Welding time models for cost calculations in the early stages of the design process

It is generally accepted that between 70 and 80% of manufacturing costs can be attributed to design. Nevertheless, it is difficult for the designer to estimate manufacturing costs accurately, especially when alternative constructions are compared at the conceptual design phase, because of the lack of cost information and appropriate tools. In general, previous reports concerning optimisation of a welded structure have used the mass of the product as the basis for the cost comparison. However, it can easily be shown using a simple example that the use of product mass as the sole manufacturing cost estimator is unsatisfactory. This study describes a method of formulating welding time models for cost calculation, and presents the results of the models for particular sections, based on typical costs in Finland. This was achieved by collecting information concerning welded products from different companies. The data included 71 different welded assemblies taken from the mechanical engineering and construction industries. The welded assemblies contained in total 1 589 welded parts, 4 257 separate welds, and a total welded length of 3 188 metres. The data were modelled for statistical calculations, and models of welding time were derived by using linear regression analysis. Themodels were tested by using appropriate statistical methods, and were found to be accurate. General welding time models have been developed, valid for welding in Finland, as well as specific, more accurate models for particular companies. The models are presented in such a form that they can be used easily by a designer, enabling the cost calculation to be automated.

Requirements Management in the Software Development Process

Ohjelmistokehitys on monimutkainen prosessi. Yksi keskeisistä tekijöistä siinä on ohjelmistolle asetettavat vaatimukset. Näitä vaatimuksia on hyvin monenlaisia, ja eri tasoisia; toivotusta toiminnallisuudesta hyvinkin yksityiskohtaisiin vaatimuksiin. Näiden vaatimusten hallinta on myöskin hyvin monitahoista, vaikkakin se on kirjallisuudessa esitetty selkeänä prosessissa, joka on sarja toisistaan erottuviavaiheita. Työn painopiste oli näiden vaatimusten muutoksen ja valmiiseen ohjelmistoon kohdistuvan palautteen hallinnassa, ja kuinka vaatimustenhallintaohjelmisto voisi olla avuksi näissä prosesseissa. Vaatimustenhallintatyökalun käyttö ei sinällään ratkaise mitään ongelmia, mutta se suo puitteet parantaa vaatimusten hallitsemista. Työkalun käytöstä on muun muassa seuraavia etuja: vaatimusten keskitetty varastointi, käyttäjäoikeuksien määrittely koskien eri käyttäjiä ja heidän pääsyään näkemään tai muuttamaan tietoa, muutoksenhallintaprosessin hallinta, muutosten vaikutuksen analysointi ja jäljitettävyys ja pääsy tietoihin web-selaimella.

Influence of software development process quality on product quality

Ohjelmistojen tärkeys nykypäivän yhteiskunnalle kasvaa jatkuvasti. Monia ohjelmistoprojekteja vaivaavat ongelmat aikataulussa pysymisestä, korkean tuottavuuden ylläpitämisestä ja riittävän korkeasta laadusta. Ohjelmistokehitysprosessien parantamisessa on naiden ongelmien minimoimiseksi tehty suuria investointeja. Investointien syynä on ollut olettamus ohjelmistokehityksen kapasiteetin suora riippuvuus tuotteen laadusta. Tämän tutkimuksen tarkoituksena oli tutkia Ohjelmistokehitysprosessien parantamisen mahdollisuuksia. Olemassaolevat ohjelmistokehityksen ja Ohjelmistokehitysprosessin parantamisen mallit, tekniikat ja metodologiat esiteltiin. Esiteltyjen mallien, tekniikoiden ja metodologioiden soveltuvuus analysoitiin ja suositus mallien käytöstä annettiin.

Benchmarked Quality Measurement Process in a Software Validation Process

Jatkuva laadunmittaus osana ohjelmistoprosessia on yleistynyt ohjelmistoyritysten keskuudessa viime vuosien aikana. ISO 9001:2000 -laatustandardi vaatii yrityksiltä tuotteiden ja prosessien laadun mittaamista ja seuraamista. Laadun mittareiden valinta on haastava tehtävä. Yritykset luulevat usein mittaavansa laatua, vaikka ne todellisuudessa mittaavatkin ohjelmistojen eri ominaisuuksia kuten kokoa tai monimutkaisuutta. Tässä diplomityössä kehitetään ohjelmistojen validointiprosessiin vertailuun perustuva laadunmittausprosessi ohjelmistotuotteiden laadun arviointiin, mittaamiseen ja seurantaan. Laatumittarit valitaan ennalta määriteltyjen kriteereiden mukaisesti, ja niille asetetaan tavoitearvot vertailuanalyysistä saatujen tulosten perusteella. Laadunmittausprosessin lisäksi työssä annetaan suositus prosessin käyttöönotosta ja käytöstä osana yrityksen toimintaa, mikä mahdollistaa jatkuvan seurannan sekä kehityksen tulevaisuudessa.

Design Process of Packaging Laboratory at Lappeenranta University of Technology

The layout design process of the packaging laboratory at Lappeenranta University of Technology is documented in this thesis. Layout planning methods are discussed in general. The systematic layout planning procedure is presented in more detail as it is utilised in the case of layout planning of the packaging laboratory. General demands for research laboratory are discussed both from the machine and product perspectives. The possibilities for commercial food processing in the laboratory are discussed from the point of view of foodstuff processing regulations and hygiene demands. The layout planning process is documented and different layout possibilities are presented. Different layout drafts are evaluated and one layout draft is developed to be the final layout of the packaging laboratory. Guideline for technical planning and implementation based on the final layout is given

Software Test Process Development

In this thesis, the components important for testing work and organisational test process are identified and analysed. This work focuses on the testing activities in reallife software organisations, identifying the important test process components, observing testing work in practice, and analysing how the organisational test process could be developed. Software professionals from 14 different software organisations were interviewed to collect data on organisational test process and testing‐related factors. Moreover, additional data on organisational aspects was collected with a survey conducted on 31 organisations. This data was further analysed with the Grounded Theory method to identify the important test process components, and to observe how real‐life test organisations develop their testing activities. The results indicate that the test management at the project level is an important factor; the organisations do have sufficient test resources available, but they are not necessarily applied efficiently. In addition, organisations in general are reactive; they develop their process mainly to correct problems, not to enhance their efficiency or output quality. The results of this study allows organisations to have a better understanding of the test processes, and develop towards better practices and a culture of preventing problems, not reacting to them.

Software Development Process Modeling. Developers Perspective to Contemporary Modeling Techniques

Formal software development processes and well-defined development methodologies are nowadays seen as the definite way to produce high-quality software within time-limits and budgets. The variety of such high-level methodologies is huge ranging from rigorous process frameworks like CMMI and RUP to more lightweight agile methodologies. The need for managing this variety and the fact that practically every software development organization has its own unique set of development processes and methods have created a profession of software process engineers. Different kinds of informal and formal software process modeling languages are essential tools for process engineers. These are used to define processes in a way which allows easy management of processes, for example process dissemination, process tailoring and process enactment. The process modeling languages are usually used as a tool for process engineering where the main focus is on the processes themselves. This dissertation has a different emphasis. The dissertation analyses modern software development process modeling from the software developers’ point of view. The goal of the dissertation is to investigate whether the software process modeling and the software process models aid software developers in their day-to-day work and what are the main mechanisms for this. The focus of the work is on the Software Process Engineering Metamodel (SPEM) framework which is currently one of the most influential process modeling notations in software engineering. The research theme is elaborated through six scientific articles which represent the dissertation research done with process modeling during an approximately five year period. The research follows the classical engineering research discipline where the current situation is analyzed, a potentially better solution is developed and finally its implications are analyzed. The research applies a variety of different research techniques ranging from literature surveys to qualitative studies done amongst software practitioners. The key finding of the dissertation is that software process modeling notations and techniques are usually developed in process engineering terms. As a consequence the connection between the process models and actual development work is loose. In addition, the modeling standards like SPEM are partially incomplete when it comes to pragmatic process modeling needs, like light-weight modeling and combining pre-defined process components. This leads to a situation, where the full potential of process modeling techniques for aiding the daily development activities can not be achieved. Despite these difficulties the dissertation shows that it is possible to use modeling standards like SPEM to aid software developers in their work. The dissertation presents a light-weight modeling technique, which software development teams can use to quickly analyze their work practices in a more objective manner. The dissertation also shows how process modeling can be used to more easily compare different software development situations and to analyze their differences in a systematic way. Models also help to share this knowledge with others. A qualitative study done amongst Finnish software practitioners verifies the conclusions of other studies in the dissertation. Although processes and development methodologies are seen as an essential part of software development, the process modeling techniques are rarely used during the daily development work. However, the potential of these techniques intrigues the practitioners. As a conclusion the dissertation shows that process modeling techniques, most commonly used as tools for process engineers, can also be used as tools for organizing the daily software development work. This work presents theoretical solutions for bringing the process modeling closer to the ground-level software development activities. These theories are proven feasible by presenting several case studies where the modeling techniques are used e.g. to find differences in the work methods of the members of a software team and to share the process knowledge to a wider audience.

Software testing design and implementation in a small software company

Monet ohjelmistoyritykset ovat alkaneet kiinnittää yhä enemmän huomiota ohjelmistotuotteidensa laatuun. Tämä on johtanut siihen, että useimmat niistä ovat valinneet ohjelmistotestauksen välineeksi, jolla tätä laatua voidaan parantaa. Testausta ei pidä rajoittaa ainoastaan ohjelmistotuotteeseen itseensä, vaan sen tulisi kattaa koko ohjelmiston kehitysprosessi. Validaatiotestauksessa keskitytään varmistamaan, että lopputuote täyttää sille asetetut vaatimukset, kun taas verifikaatiotestausta käytetään ennaltaehkäisevänä testauksena, jolla pyritään poistamaan virheitä jo ennenkuin ne pääsevät lähdekoodiin asti. Työ, johon tämä diplomityö perustuu, tehtiin alkukevään ja kesän aikana vuonna 2003 Necsom Oy:n toimeksiannosta. Necsom on pieni suomalainen ohjelmistoyritys, jonka tutkimus- ja kehitysyksikkö toimii Lappeenrannassa.Tässä diplomityössä tutustutaan aluksi ohjelmistotestaukseen sekä eri tapoihin sen organisoimiseksi. Tämän lisäksi annetaan yleisiä ohjeita testisuunnitelmien ja testaustapausten tekoon, joita onnistunut ja tehokas testaus edellyttää. Kun tämä teoria on käyty läpi, esitetään esimerkkinä kuinka sisäinen ohjelmistotestaus toteutettiin Necsomilla. Lopuksi esitetään johtopäätökset, joihin päädyttiin käytännön testausprosessin seuraamisen jälkeen ja annetaan jatkotoimenpide-ehdotuksia.

Measuring software security from the design of software

The vast majority of our contemporary society owns a mobile phone, which has resulted in a dramatic rise in the amount of networked computers in recent years. Security issues in the computers have followed the same trend and nearly everyone is now affected by such issues. How could the situation be improved? For software engineers, an obvious answer is to build computer software with security in mind. A problem with building software with security is how to define secure software or how to measure security. This thesis divides the problem into three research questions. First, how can we measure the security of software? Second, what types of tools are available for measuring security? And finally, what do these tools reveal about the security of software? Measuring tools of these kind are commonly called metrics. This thesis is focused on the perspective of software engineers in the software design phase. Focus on the design phase means that code level semantics or programming language specifics are not discussed in this work. Organizational policy, management issues or software development process are also out of the scope. The first two research problems were studied using a literature review while the third was studied using a case study research. The target of the case study was a Java based email server called Apache James, which had details from its changelog and security issues available and the source code was accessible. The research revealed that there is a consensus in the terminology on software security. Security verification activities are commonly divided into evaluation and assurance. The focus of this work was in assurance, which means to verify one’s own work. There are 34 metrics available for security measurements, of which five are evaluation metrics and 29 are assurance metrics. We found, however, that the general quality of these metrics was not good. Only three metrics in the design category passed the inspection criteria and could be used in the case study. The metrics claim to give quantitative information on the security of the software, but in practice they were limited to evaluating different versions of the same software. Apart from being relative, the metrics were unable to detect security issues or point out problems in the design. Furthermore, interpreting the metrics’ results was difficult. In conclusion, the general state of the software security metrics leaves a lot to be desired. The metrics studied had both theoretical and practical issues, and are not suitable for daily engineering workflows. The metrics studied provided a basis for further research, since they pointed out areas where the security metrics were necessary to improve whether verification of security from the design was desired.

Software Process Modeling with Eclipse Process Framework

The software development industry is constantly evolving. The rise of the agile methodologies in the late 1990s, and new development tools and technologies require growing attention for everybody working within this industry. The organizations have, however, had a mixture of various processes and different process languages since a standard software development process language has not been available. A promising process meta-model called Software & Systems Process Engineering Meta- Model (SPEM) 2.0 has been released recently. This is applied by tools such as Eclipse Process Framework Composer, which is designed for implementing and maintaining processes and method content. Its aim is to support a broad variety of project types and development styles. This thesis presents the concepts of software processes, models, traditional and agile approaches, method engineering, and software process improvement. Some of the most well-known methodologies (RUP, OpenUP, OpenMethod, XP and Scrum) are also introduced with a comparison provided between them. The main focus is on the Eclipse Process Framework and SPEM 2.0, their capabilities, usage and modeling. As a proof of concept, I present a case study of modeling OpenMethod with EPF Composer and SPEM 2.0. The results show that the new meta-model and tool have made it possible to easily manage method content, publish versions with customized content, and connect project tools (such as MS Project) with the process content. The software process modeling also acts as a process improvement activity.

Re-usable ASIC integrationverification software architecture

Mikropiirien valmistus- ja suunnittelutekniikoiden kehittyminen mahdollistaa yhä monimutkaisempien mikropiirien valmistamisen. Piirien verifioinnista onkin tullut prosessin aikaa vievin osa,sillä kompleksisuuden kasvaessa kasvaa verifioinnin tarve eksponentiaalisesti. Vaikka erinäisiä strategioita piirien integroinnin verifiointiin on esitetty, mm. verifioinnin jakaminen koko suunnitteluprosessin ajalle, jopa yli puolet koko piirin suunnitteluun ja valmistukseen käytetystä työmäärästä kuluu verifiointiin. Uudelleenkäytettävät komponentit ovat pääosassa piirin suunnittelussa, mutta verifioinnissa uudelleenkäytettävyyttä ei ole otettu kunnolla käyttöön ainakaan verifiointiohjelmistojen osalta. Tämä diplomityö esittelee uudelleenkäytettävän mikropiirien verifiointiohjelmistoarkkitehtuurin, jolla saadaan verifiointitaakkaa vähennettyä poistamalla verifioinnissa käytettävien ohjelmistojen uudelleensuunnittelun ja toteuttamisen tarvetta.

Object-oriented development of client / server application: case study of service control software

Tässä työssä on esitetty sen ohjelmiston kehittämisen prosessi, joka on tarkoitettu annettavien palveluiden valvottavaksi käyttäen prototyyppimallia. Raportti sisältää vaatimusten, kohteisiin suunnatun analyysin ja suunnittelun, realisointiprosessien kuvauksen ja prototyypin testauksen. Ohjelmiston käyttöala – antavien palveluiden valvonta. Vaatimukset sovellukselle analysoitiin ohjelmistomarkkinoiden perusteella sekä ohjelmiston engineeringin periaatteiden mukaisesti. Ohjelmiston prototyyppi on realisoitu käyttäen asiakas-/palvelinhybridimallia sekä ralaatiokantaa. Kehitetty ohjelmisto on tarkoitettu venäläisille tietokonekerhoille, jotka erikoistuvat pelipalvelinten antamiseen.

Evolutionary computing in search-based software engineering

This master’s thesis aims to study and represent from literature how evolutionary algorithms are used to solve different search and optimisation problems in the area of software engineering. Evolutionary algorithms are methods, which imitate the natural evolution process. An artificial evolution process evaluates fitness of each individual, which are solution candidates. The next population of candidate solutions is formed by using the good properties of the current population by applying different mutation and crossover operations. Different kinds of evolutionary algorithm applications related to software engineering were searched in the literature. Applications were classified and represented. Also the necessary basics about evolutionary algorithms were presented. It was concluded, that majority of evolutionary algorithm applications related to software engineering were about software design or testing. For example, there were applications about classifying software production data, project scheduling, static task scheduling related to parallel computing, allocating modules to subsystems, N-version programming, test data generation and generating an integration test order. Many applications were experimental testing rather than ready for real production use. There were also some Computer Aided Software Engineering tools based on evolutionary algorithms.

Software methods for HTML files protection in local / corporate networks: review and implementation

Tässä luomistyössä on esitetty tutkimus informaation suojaamisen menetelmien osalta paikallisissa ja ryhmäkuntaisissa verkoissa. Tutkimukseen kuuluu nykyaikaisten kryptagraafisten järjestelmien, Internetin/Intranetin ohjelmointikeinojen ja pääsyoikeuksien jakelumenetelmien analyysi. Tutkimusten perusteella on laadittu ohjelmiston prototyyppi HTML-tiedostojen suojaamista varten. Ohjelmiston laatimisprosessi on sisältänyt vaatimusten, järjestelmän ja suojelukomponenttien suunnittelun ja protytyypin testauksen. Ohjelmiston realisoinnin jälkeen kirjoitettiin käyttöohjeet. Ohjelmiston prototyyppi suojaa informaatiota HTML-tiedoston koko käytön aikana ja eri yrityksissä voidaan käyttää sitä pienien laajennuksien jälkeen.