Power Consumption in Carbon Capture and Storage Systems (CCS) and Possibilities to Reduce Power Consumption with Variable Speed Drives

The aim of this master´s thesis is to study which processes increase the auxiliary power consumption in carbon capture and storage processes and if it is possible to reduce the auxiliary power consumption with variable speed drives. Also the cost of carbon capture and storage is studied. Data about auxiliary power consumption in carbon capture is gathered from various studies and estimates made by various research centres. Based on these studies a view is presented how the power auxiliary power consumption is divided between different processes in carbon capture processes. In a literary study, the operation of three basic carbon capture systems is described. Also different methods to transport carbon dioxide and carbon dioxide storage options are described in this section. At the end of the thesis processes that consume most of the auxiliary power are defined and possibilities to reduce the auxiliary power consumption are evaluated. Cost of carbon capture, transport and storage are also evaluated at this point and in the case that the carbon capture and storage systems are fully deployed. According to the results, it can be estimated what are the processes are where variable speed drives can be used and what kind of cost and power consumption reduction could be achieved. Results also show how large a project carbon capture and storage is if it is fully deployed.

Lebesgue and Sobolev spaces with variable exponents

Kirjallisuusarvostelu

Analysis of the voltage source inverter with small DC-link capacitor

IIn electric drives, frequency converters are used to generatefor the electric motor the AC voltage with variable frequency and amplitude. When considering the annual sale of drives in values of money and units sold, the use of low-performance drives appears to be in predominant. These drives have tobe very cost effective to manufacture and use, while they are also expected to fulfill the harmonic distortion standards. One of the objectives has also been to extend the lifetime of the frequency converter. In a traditional frequency converter, a relatively large electrolytic DC-link capacitor is used. Electrolytic capacitors are large, heavy and rather expensive components. In many cases, the lifetime of the electrolytic capacitor is the main factor limiting the lifetime of the frequency converter. To overcome the problem, the electrolytic capacitor is replaced with a metallized polypropylene film capacitor (MPPF). The MPPF has improved properties when compared to the electrolytic capacitor. By replacing the electrolytic capacitor with a film capacitor the energy storage of the DC-linkwill be decreased. Thus, the instantaneous power supplied to the motor correlates with the instantaneous power taken from the network. This yields a continuousDC-link current fed by the diode rectifier bridge. As a consequence, the line current harmonics clearly decrease. Because of the decreased energy storage, the DC-link voltage fluctuates. This sets additional conditions to the controllers of the frequency converter to compensate the fluctuation from the supplied motor phase voltages. In this work three-phase and single-phase frequency converters with small DC-link capacitor are analyzed. The evaluation is obtained with simulations and laboratory measurements.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Patient education to support self-management of patients with mental illness

This study explores areas which need to be improved to develop the quality of patient education to support self-management of patients with mental illness in psychiatric hospitals. The study was conducted in five phases during the period 2000 – 2007. First, patients‘ (n = 313) satisfaction with patient education were investigated. Second, patients' (n = 51) experiences of patient education were explored. Third, a national survey was conducted to investigate realisation of patient education from the staff (n = 55) viewpoint. Fourth, outcomes of patient education were investigated by evaluating the impacts of different patient education methods on patients‘ (n = 311) attitudes towards medication, knowledge level and importance of information. Fifth, patients‘ (n = 16) perceptions of different patient education methods were explored. Patients reported poor satisfaction with patient education (Phase I), and they have considerable need to receive information during their hospital stay (Phase II). Described by staff, the content of patient education covered almost all informational areas investigated. However, discrepancies related to the realisation of patient education were found. (Phase III.) Evaluation of different patient education methods indicate that patients derived benefits from structured patient education with supportive methods (Phase IV) and patients also perceived that these methods supported their information receiving (Phase V). In order to improve the quality of patient education to support self-management of patients with mental illness patient education should be systematically and individually provided to all patients by using different educational methods. Realisation of this should be ensured by providing written instructions, improving nurses‘ knowledge and skills as well ensuring operating conditions.

Nurse-led interpersonal counselling for depressive symptoms in patients with myocardial infarction

The broad interest of this intervention study is in two worldwide remarkable diseases, myocardial infarction and depression. The purpose of the 18-month follow-up study was to evaluate the outcomes of interpersonal counselling implemented by a psychiatric nurse, and to examine the recovery experienced by the patients after myocardial infarction. The interpersonal counseling consisted of a short-term (max 6 sessions) depression-focused intervention modified for myocardial infarction patients. The main principle of interpersonal counselling is that depressive symptoms relate to interpersonal relations. The measured outcomes of the intervention consisted of changes in depressive symptoms and distress, health-related quality of life and the use of health care services. The data consisted of 103 patients with acute myocardial infarction and with sufficient knowledge of Finnish language, and they were randomized into intervention group (n=51) and control group (n=52) with standard care. Depressive symptoms were measured using Beck Depression Inventory, and distress using Symptom Checklist-25. The instrument to measure health-related quality of life was EuroQol-5 Dimensions. All instruments were used at three measurements: in hospital, at 6 months and at 18 months after hospital discharge. The Use of Health Care Services questionnaire was used during the 6- and 18-month period after hospital discharge. In addition, satisfaction with the intervention and with information received from the health-care professional was evaluated during the follow-up. To examine recovery, the patients kept diaries during a 6-month period and they were interviewed at 18 months after myocardial infarction. The number of patients with depressive symptoms decreased significantly more in the intervention group compared with the control group during 18 months of follow-up. Distress decreased significantly more among patients under 60 years in the intervention group than in the control group, but the difference was not significant between the groups. No differences in the changes of health-related quality of life were found between the groups during follow-up. However, in the group of patients under 60 years, the improvement of health-related quality of life in the intervention was significantly better in the intervention group compared with the control group during the follow-up. During the follow-up period, there was even a decline in the use of somatic specialized health care services in the intervention group and among intervention patients who had no other long-term disease. Considering recovery experienced by the patients, main categories including many supporting and inhibiting factors and subcategories were identified: clinical and physical, psychological, social, functional and professional category. No differences between the groups were found in satisfaction with information received from the professionals. The brief and easy-to-learn intervention, with which the patients were satisfied, seems to decrease depressive symptoms after myocardial infarction. Interpersonal counselling seems to be beneficial especially with younger patients. These results justify adopting depression screening and interpersonal counselling as part of routine care after myocardial infarction. The first stage evaluation of the use of health care services is interesting, and calls for more studies. From the perspective of individual patients, recovery after myocardial infarction seems to consist of many supporting and inhibiting factors. This is something that is important to take into account in developing nursing practice. The results indicate a need for further studies in outcomes of interpersonal counselling and recovery experienced by the patients after myocardial infarction. In addition, the results encourage widening the research perspective to nursing administration and educational level.

Päämääriä, ajelehtimista, tietämättömyyttä, etsintää: Koulutusvalinnat, opinnot ja koulutuksen vaihtaminen yliopisto-opiskelijoiden kokemana 2000 -luvun taitteessa

Tutkimuksessa tarkastellaan yliopisto-opiskelua, opintojen kokemista ja niiden kulkua alkaen koulutusvalinnoista. Lisäksi tutkimuksessa pyritään ymmärtämään ja kuvaamaan yliopisto-opintojen aikaista koulutuksen vaihtamista prosessina. Kyseessä on seurantatutkimus Turun yliopistossa vuonna 1998 aloittaneesta opiskelijakohortista. Tutkittavat opiskelijat valittiin sillä perusteella, että he vastasivat kolmeen opintoja koskevaan kyselyyn ja olivat vähintään kolmen vuoden ajan läsnä olevina opiskelijoina. Opiskelijat (n=440) jaettiin neljään vertailuryhmään: 1) opintoihinsa tyytyväiset, 2) ensimmäisen vuoden jälkeen koulutusta vaihtaneet, 3) toisen vuoden jälkeen koulutusta vaihtaneet ja 4) koulutusta vaihtaa halunneet. Tutkimusaineisto koostuu kolmesta kyselystä, opintorekisteriaineistosta ja koulutusta opintojen aikana vaihtaneiden opiskelijoiden haastatteluista (n=22). Kyselyt tehtiin ensimmäisen, toisen ja kolmannen opintovuoden kevätlukukausilla ja haastattelut vuonna 2002, jolloin opiskelijat opiskelivat Turun yliopistossa neljättä tai viidettä vuotta. Kyselyiden avulla tutkittiin eroavatko koulutusta vaihtaneet opiskelijat muista opiskelijoista rakenteellisilta tekijöiltään tai opintokokemuksissaan. Opintorekisteriaineiston perusteella tutkittiin eroavatko koulutusta vaihtaneet opiskelijat koulutuksessa pysyneistä opiskelijoista opintojen kulussa. Kyselyiden ja haastatteluiden avulla tutkittiin minkälaisia tietoja ja odotuksia opiskelijoilla oli yliopisto-opiskelusta ollut ennen opintojen aloittamista. Haastatteluiden perusteella tutkittiin mitä syitä koulutuksen vaihtamisen taustalla oli ja minkälaisina kertomuksina koulutuksen vaihtamisprosessi näyttäytyi. Koulutusta vaihtaneet opiskelijat erosivat koulutuksessa pysyneistä opiskelijoista aiemman koulutuksen määrän, iän ja perheellisyyden suhteen. Verrattaessa ensimmäisen ja toisen vuoden jälkeen koulutusta vaihtaneita opiskelijoita keskenään havaittiin näillä ryhmillä olevan erilainen perhetausta. Koulutusta valittaessa tärkein tekijä oli kiinnostus alaa kohtaan. Toiseksi voimakkain hakutekijä oli muilla paitsi ensimmäisen vuoden jälkeen koulutusta vaihtaneilla valmiudet haluttuun ammattiin. Vuorostaan ensimmäisen vuoden jälkeen koulutusta vaihtaneilla toiseksi tärkein tekijä hakeutumisessa oli helppo sisäänpääsy opintoihin. Suurin osa opiskelijoista oli päässyt ensisijaisesti haluamaansa koulutukseen. Koulutusta myöhemmin vaihtaneissa ryhmissä ja koulutuksen vaihtoa halunneiden ryhmässä ensisijaisesti haluttuun koulutukseen päässeitä oli alle puolet. Odotukset opiskelusta eivät täysin täyttyneet ensimmäisen puolen vuoden opiskelun aikana. Tutkittujen ryhmien välillä havaittiin eroja kokemuksissa koulutuksen sopivuudesta itselle. Koulutuksen vaihtaminen oli myönteinen kokemus, ja uusi koulutus koettiin aiempaa koulutusta sopivammaksi itselle. Kolmannen vuoden kevätlukukaudella omaa koulutusta kohtaan koettu kiinnostus oli voimakasta muissa ryhmissä paitsi koulutuksen vaihtoa halunneissa. Harvimmin positiivisia tunteita opiskelua kohtaan kokivat vaihtoa halunneet opiskelijat. Koulutuksen vaihtaminen vähensi opintoihin kiinnittymättömyyttä. Koulutuksen vaihtoa halunneiden kokemukset nykyisen koulutuksensa ilmapiiristä olivat negatiivisimpia. Koulutuksen vaihtaminen vaikutti myönteisesti myös opetuksen kokemiseen. Opinnot etenivät kaikissa tutkituissa ryhmissä tasaisesti. Koulutuksen vaihtamisen jälkeisenä vuonna opinnot etenivät vaihtaneissa ryhmissä keskimääräistä enemmän. Haastatteluiden mukaan pääasiallisia syitä koulutuksen vaihtamiselle olivat päätyminen toissijaiseen koulutukseen ja pettyminen aloittamaansa koulutukseen. Narratiivien analyysin avulla tutkimuksessa löydettiin neljä erilaista tarinaa vaihtamisprosessista: 1) toissijaisesta koulutuksesta ensisijaiseen koulutukseen vaihtaminen, 2) ensisijaiseen koulutukseen pettyminen, 3) kiinnostavampaan koulutukseen ajautuminen ja 4) oman alan löytyminen etsinnän kautta. Vaikka koulutuspolitiikassa koulutuksen vaihtaminen nähdään ongelmana, oli se tämän tutkimuksen mukaan opiskelijalle myönteinen kokemus. Tämän tutkimuksen perusteella tulisikin kiinnittää huomiota opiskelijoihin, jotka haluaisivat vaihtaa koulutuksesta toiseen. Heillä opintojen eteneminen osoittautui hitaimmaksi ja opintokokemukset negatiivisimmiksi. Koulutusta vaihtaneiden opiskelijoiden opintojen eteneminen näytti hitaalta verrattuna opintoihinsa tyytyväisiin opiskelijoihin. Koulutuksen vaihtamisen jälkeen opintojen eteneminen kuitenkin nopeutui ja opintotyytyväisyys lisääntyi.

Customer satisfaction data utilization: identifying value drivers and information use practices

The objective of this master’s thesis was twofold: first to examine the concept of customer value and its drivers and second to identify information use practices. The first part of the study represents explorative research that was carried out by examining a case company’s customer satisfaction data that was used to identify sales and technical customer service related value drivers on a detailed attribute level. This was followed by an examination of whether these attributes had been commented on in a positive or a negative light and what were the reasons why the case company had received higher or lower ratings than its competitor. As a result a classification of different sales and technical customer service related attributes was created. The results indicated that the case company has performed well, but that the results varied on the company’s business segment level. The case company’s staff, service and the benefits from a long-lasting relationship came up in a positive light whereas attitude, flexibility and reaction time came up in a negative light. The reasons for a higher or lower score in comparison to competitor varied. The results indicated that a customer’s satisfaction with the company’s performance did not always mean that the company was outperforming the competition. The second part of the study focused on customer satisfaction information use from the viewpoints of information access, dissemination and reaction. The study was conducted by running an internal survey among the case company’s staff. The results showed that information use practices varied across the company and some units or teams had taken a more proactive approach to the information use than others.

Vanhempien tyytyväisyys peruskoulun toimintaan ja koulunuudistuksia koskevat asenteet

Parents' satisfaction with the comprehensive school and reactions to current school reforms

Development of a simulation tool for torsional vibration of branched power transmission system

In this master's thesis a mechanical model that is driven with variable speed synchronous machine was developed. The developed mechanical model simulates the mechanics of power transmission and its torsional vibrations. The mechanical model was developed for the need of the branched mechanics of a rolling mill and the propulsion system of a tanker. First, the scope of the thesis was to clarify the concepts connected to the mechanical model. The clarified concepts are the variable speed drive, the mechanics of power transmission and the vibrationsin the power transmission. Next, the mechanical model with straight shaft line and twelve moments of inertia that existed in the beginning was developed to be branched considering the case of parallel machines and the case of parallel rolls. Additionally, the model was expanded for the need of moreaccurate simulation to up to thirty moments of inertia. The model was also enhanced to enable three phase short circuit situation of the simulated machine. After that the mechanical model was validated by comparing the results of the developed simulation tool to results of other simulation tools. The compared results are the natural frequencies and mode shapes of torsional vibration, the response of the load torque step and the stress in the mechanical system occurred by the permutation of the magnetic field that is arisen from the three phase short circuit situation. The comparisons were accomplished well and the mechanical model was validated for the compared cases. Further development to be made is to develop the load torque to be time-dependent and to install two frequency converters and two FEM modeled machines to be simulated parallel.

Jäähdytysjärjestelmän vaikutus kiinteistön elinkaaren aikaisiin tuottoihin

Ilmastoinnin jäähdytys yleistyy toimisto- ja hotellikiinteistöissä jatkuvasti. Perinteinen tapa tuottaa jäähdytysenergia on kiinteistökohtainen vedenjäähdytysjärjestelmä. Helsingissä on ollut vuodesta 2000 lähtien mahdollista liittyä Helsingin energian kaukojäähdytysverkostoon. Jäähdytysjärjestelmien ominaisuudet poikkeavat toisistaan ja niistä aiheutuu kiinteistönomistajalle erilaisia kustannuksia. Kiinteistöstä saataviin tuottoihin vaikuttaa kustannusten lisäksi vuokralaisen tyytyväisyys. Tämän vuoksi työssä selvitettiin vuokralaisen tarpeet jäähdytysjärjestelmälle haastattelemalla vuokralaisen edustajia. Tässä diplomityössä vertaillaan kaukojäähdytyksen ja kiinteistökohtaisen jäähdytysjärjestelmän kustannuksia, sekä vaikutuksia kiinteistön elinkaarituottoihin kiinteistönomistajan näkökulmasta. Kerättyjen kustannusten perusteella suoritetaan elinkaarikustannuslaskenta GaBi-ohjelmalla. Vuokralaisen tarpeista jäähdytysjärjestelmälle tunnistetaan olennaisiksi toimintavarmuus, ympäristöystävällisyys sekä hiljainen äänitaso. Nämä ovat lisäarvotekijöitä, joille työssä määritetään painoarvo ja jotka huomioidaan laskennassa. Diplomityö osoitti kaukojäähdytyksen kannattavaksi vaihtoehdoksi kiinteistökohtaiselle järjestelmälle, kun huomioidaan hankinta- ja käyttökustannusten lisäksi asennustöiden, käyttöönoton, huollon ja kunnossapidon sekä loppusijoituksen kustannukset. Myös valikoituneet lisäarvotekijät puoltavat kaukojäähdytystä ja niiden kompensointi lisää kiinteistökohtaisen järjestelmän kustannuksia.

Formation and Control of Trace Metal Emissions in Co-Firing of Biomass, Peat, and Wastes in Fluidised Bed Combustors

Environmentally harmful consequences of fossil fuel utilisation andthe landfilling of wastes have increased the interest among the energy producers to consider the use of alternative fuels like wood fuels and Refuse-Derived Fuels, RDFs. The fluidised bed technology that allows the flexible use of a variety of different fuels is commonly used at small- and medium-sized power plants ofmunicipalities and industry in Finland. Since there is only one mass-burn plantcurrently in operation in the country and no intention to build new ones, the co-firing of pre-processed wastes in fluidised bed boilers has become the most generally applied waste-to-energy concept in Finland. The recently validated EU Directive on Incineration of Wastes aims to mitigate environmentally harmful pollutants of waste incineration and co-incineration of wastes with conventional fuels. Apart from gaseous flue gas pollutants and dust, the emissions of toxic tracemetals are limited. The implementation of the Directive's restrictions in the Finnish legislation is assumed to limit the co-firing of waste fuels, due to the insufficient reduction of the regulated air pollutants in the existing flue gas cleaning devices. Trace metals emission formation and reduction in the ESP, the condensing wet scrubber, the fabric filter, and the humidification reactor were studied, experimentally, in full- and pilot-scale combustors utilising the bubbling fluidised bed technology, and, theoretically, by means of reactor model calculations. The core of the model is a thermodynamic equilibrium analysis. The experiments were carried out with wood chips, sawdust, and peat, and their refuse-derived fuel, RDF, blends. In all, ten different fuels or fuel blends were tested. Relatively high concentrations of trace metals in RDFs compared to the concentrations of these metals in wood fuels increased the trace metal concentrations in the flue gas after the boiler ten- to hundred-folds, when RDF was co-fired with sawdust in a full-scale BFB boiler. In the case of peat, lesser increase in trace metal concentrations was observed, due to the higher initial trace metal concentrations of peat compared to sawdust. Despite the high removal rate of most of the trace metals in the ESP, the Directive emission limits for trace metals were exceeded in each of the RDF co-firing tests. The dominat trace metals in fluegas after the ESP were Cu, Pb and Mn. In the condensing wet scrubber, the flue gas trace metal emissions were reduced below the Directive emission limits, whenRDF pellet was used as a co-firing fuel together with sawdust and peat. High chlorine content of the RDFs enhanced the mercuric chloride formation and hence the mercury removal in the ESP and scrubber. Mercury emissions were lower than theDirective emission limit for total Hg, 0.05 mg/Nm3, in all full-scale co-firingtests already in the flue gas after the ESP. The pilot-scale experiments with aBFB combustor equipped with a fabric filter revealed that the fabric filter alone is able to reduce the trace metal concentrations, including mercury, in the flue gas during the RDF co-firing approximately to the same level as they are during the wood chip firing. Lower trace metal emissions than the Directive limits were easily reached even with a 40% thermal share of RDF co-firing with sawdust.Enrichment of trace metals in the submicron fly ash particle fraction because of RDF co-firing was not observed in the test runs where sawdust was used as the main fuel. The combustion of RDF pellets with peat caused an enrichment of As, Cd, Co, Pb, Sb, and V in the submicron particle mode. Accumulation and release oftrace metals in the bed material was examined by means of a bed material analysis, mass balance calculations and a reactor model. Lead, zinc and copper were found to have a tendency to be accumulated in the bed material but also to have a tendency to be released from the bed material into the combustion gases, if the combustion conditions were changed. The concentration of the trace metal in the combustion gases of the bubbling fluidised bed boiler was found to be a summary of trace metal fluxes from three main sources. They were (1) the trace metal flux from the burning fuel particle (2) the trace metal flux from the ash in the bed, and (3) the trace metal flux from the active alkali metal layer on the sand (and ash) particles in the bed. The amount of chlorine in the system, the combustion temperature, the fuel ash composition and the saturation state of the bed material in regard to trace metals were discovered to be key factors affecting therelease process. During the co-firing of waste fuels with variable amounts of e.g. ash and chlorine, it is extremely important to consider the possible ongoingaccumulation and/or release of the trace metals in the bed, when determining the flue gas trace metal emissions. If the state of the combustion process in regard to trace metals accumulation and/or release in the bed material is not known,it may happen that emissions from the bed material rather than the combustion of the fuel in question are measured and reported.

Kaukolämpöjärjestelmän suunnittelu Liljendalin kunnassa

Tämän työn tavoitteena on löytää suositeltavat mitoitusarvot Liljendalin kunnan kaukolämpöjärjestelmään. Kirjallisuuden perusteella tarkastellaan kaukolämpö-järjestelmän suunnittelua ja mitoitusta sekä lämmön hinnoittelua ja niistä annettuja määräyksiä, suosituksia ja ohjeita. Työssä käsitellään mahdollisuuksia ja keinoja kaukolämmityksen siirtolämpötilojen pienentämiseen. Lisäksi vertaillaan nykyarvomenetelmällä laskemalla kaukolämpöjärjestelmän siirtokustannuksia eri mitoituslämpötiloilla, putkikoolla ja eristyspaksuuksilla. Lämmön myyntihinnalle on tehty tariffiehdotus. Lopuksi on esitetty lämpökeskuksen hankintaa koskevia tietoja. Laskennan tuloksena havaittiin, että siirtolämpötilojen, putkikoon ja eristyspaksuuden oikealla valinnalla voidaan säästää lämmönsiirron kustannuksissa. Laskelmien perusteella suositellaan Liljendalin kunnan kaukolämpöjärjestelmän mitoituslämpötiloiksi 100/50°C ja eristyspaksuudeksi III-luokan eriste. Putkikoon oikealla valinnalla voidaan säästää merkittävästi varsinkin, kun kyseessä on lyhyt siirtoetäisyys. Putkikoon valinnassa on kuitenkin huomioitava mahdolliset tulevaisuuden laajennukset verkossa ja kulutuksen kasvu.

Kustannussäästöpotentiaali sivutuotekuljetuksissa

Tämä diplomityö tehtiin UPM-Kymmene Oyj:lle. Työssä tutkittiin kustannussäästöpotentiaalia hakkeiden, purujen ja kuorien kuljetuksissa uudenlaisten reittisuunnitelmien avulla. Tavoitteena oli löytää uusi tehokkaampi toimintamalli. Sivutuotevolyymeina käytettiin vuonna 2004 toteutuneita määriä ja laskelmat tehtiin vuodelta 2003 olevilla taulukkotaksoilla. Niitä ei ole päivitetty vuoden 2003 jälkeen eikä niihin ole lisätty polttoaineen hinnan noususta johtuvia korotuksia. Vertailun vuoksi liitteissä on esitetty sama laskelma vuoden 2004 sopimushinnoilla. Kustannussäästöjä saavutettiin nykytoimintamallin perusteella muodostettujen monipistekuljetusreittien sekä lineaarisen optimoinnin avulla. Optimoinnissa käsiteltiin ainoastaan koivuviiluhakkeiden ja purujen volyymeja. Monipistekuljetusreitteihin lisättiin mukaan jätepaperikuljetuksia ja vaneritehtaiden välisiä viilukuljetuksia. Niiden avulla oli mahdollista hyödyntää volyymien vastavirtoja. Kustannussäästöjen muodostumiseen vaikutti oleellisesti kuljetusten keskitetty ohjausmalli.

Näkökulmia matkailun ohjelmapalveluihin Case: Savonlinnan alue

Tutkielman päätavoitteena on kuvata ohjelmapalveluiden tilaa case-alueella. Ohjelmapalveluiden tilaa on käsitelty viidestä eri näkökulmasta: Alueellisessa näkökulmassa on haluttu saada tietoon todelliset syyt, miksi asiakas, eli turisti tulee juuri case-alueelle. Ohjelmapalveluryhmä –näkökulmassa on tarkasteltu, millaisia ohjelmapalveluita case–alueella käytetään. Asiakasyhteys –näkökulmassa on määritelty asiakaskunnat, jotka näitä ohjelmapalveluja käyttävät. Tyytyväisyys tarjontaan ja kehitystarpeet –näkökulmassa on tuotu esille ohjelmapalvelujen kehitystarpeita sekä tyytyväisyyttä ohjelmapalveluiden tarjontaan. Yhteistyön kehittämisnäkökulmassa on haettu vastauksia ohjelmapalveluyrittäjän sekä palvelun ostajan yhteistyötoimintaan ja sen kehittämiseen. Tutkielmassa on käytetty kvalitatiivista eli laadullista tutkimusta. Tutkimusmetodiltaan työ on case-tutkimus. Tutkimusmenetelmänä käytettiin henkilökohtaisia haastatteluja. Todellinen tarve tietää alueen ohjelmapalveluiden tilasta sekä halu kehittää case-alueen ohjelmapalveluja antoi sysäyksen tälle tutkielmalle. Alueella toimii erilaisia ohjelmapalveluiden tarjoajia, jotka haluavat kasvattaa asiakasmääriään ja kehittää yhteistyötä välittäjäyritysten kanssa. Matkailun kehittyminen ja kova kilpailu pakottaa ohjelmapalveluyritykset muuntautumaan monipuolisiksi tarjoajiksi, jossa epäonnistumiseen ei ole varaa. Tutkielman tuloksina saatiin aikaan uusia kehittämisideoita. Kehittämisideat kohdistuivat mm. tarjontaan, palveluun, hinnoitteluun, ja yhteistyöhön. ***** The main aim of this qualitative case study is to examine the state of special events services in the case area. The state of the services is examined from five different perspectives. The first (regional) perspective determines the true reasons, why the tourist comes to the case area. The second (special events) perspective examines what kind of special events are arranged in the case area. The third (customer-oriented) perspective defines the tourists, who use these services. The fourth perspective (customer satisfaction and development targets) introduces some development targets and examines the satisfaction with the special events services offered. The fifth (co-operative) perspective examines the co-operation between the special events entrepreneur and the consumer and proposes some improvements. The data of the study was collected by interviews. This study was triggered by the need to examine the state of special events and to develop the special events services in the case area. There are different special events providers in the case area, who want to expand their clientele and improve the co-operation with the suppliers. The development of the tourist industry and the competition in the branch demands diversity from the special events entrepreneurs. The analysis revealed some new ideas on how to develop the service and pricing and how to improve co-operation in this particular branch.