LTO- laitteiden vuosihyötysuhteiden vertailututkimus

Tämän työn tavoitteena oli laskea ja vertailla eroja lämmön talteenottolaitteistojen vuosihyötysuhteissa. Tavoitteena oli erityisesti löytää selkeät perusteet Suomen Rakennusmääräyskokoelman osassa D2 esitetyille arvoille vuosihyötysuhdetta laskettaessa. Työn kirjallisuusosassa on käsitelty yleisellä tasolla erityyppisten lämmön talteenottolaitteistojen teoriaa, toimintaperiaatteita ja soveltuvuutta erilaisiin käyttöolosuhteisiin. Työn empiirisessä osassa selvitettiin laboratorio-olosuhteissa virtauksessa mitattujen lämpötila- ja kosteusolosuhteiden vaikutusta lämmön talteenottolaitteiden toimintaan. Lisäksi työssä esitellään yleisellä tasolla mittauksissa käytettyjen mittalaitteiden toimintaa. Suoritettujen mittausten ja laskennan perusteella havaittiin, että laitteistojen vuosihyötysuhteiden välille saatiin odotetunlaisia eroja. Parhaimpiin tuloksiin päästiin regeneratiivisella lämmön talteenottolaitteella.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Kaasunpolton tutkimuslaitteiston mittausten suunnittelu

Tämä diplomityö on Lappeenrannan teknillisessä yliopistossa aloitetun kaasunpolttotutkimushankkeen ensimmäinen tutkimusjakso. Tutkimushanketta varten on LTY:n voimalaitostekniikan koepolttolaboratoriossa rakennettu kaasunpolton tutkimuslaitteisto, jolla tässä diplomityössä perehdytään kaasuliekin lämpötilan mittausmenetelmiin, lämmönsiirtoon ja syntyviin päästöihin neste- ja maakaasupoltossa. Hankkeen toisessa tutkimusjaksossa laitteistolla tutkitaan regenaratiivista polttoa, ja polttoaineena käytetään neste- ja maakaasun lisäksi muita kaasuja kuten vetyä ja erilaisia seoskaasuja. Kaasunpolttotutkimushankkeen kokonaistavoitteena on pienentää kaasunpoltossa syntyviä NOx-päästöjä ja parantaa palamishyötysuhdetta ja tätä kautta pienentää laitteiston kokoa ja vähentää hiilidioksidipäästöjä.

Voimalaitoskattilan pyörivän regeneratiivisen ilman esilämmittimen suorituskyky ja mitoitus

Diplomityön tarkoituksena oli kehittää laskentaohjelma pyörivälle regeneratiiviselle lämmönsiirtimelle. Työ tehtiin Foster Wheeler Energia Oy:n Varkauden toimipisteessä. Työn ensimmäisessä osuudessa tutkittiin kirjallisuuden avulla regeneraattoreihin liittyvää teoriaa. Tämä osuus sisältää regeneratiivisen lämmönsiirron perusteita, regeneraattoreiden luokittelua, sektorijakoja, vuotoja, lämpöpintojen geometriaa ja likaantumista. Soveltavassa osassa tehtiin laskentaohjelma, jonka avulla voidaan laskea pyörivän regeneraattorin mitoitus- ja suorituskykylaskuja. Lisäksi ohjelman avulla voidaan laskea regeneraattorin lämpötilaprofiili.

Prosessihyötysuhteen parantamiskohteiden kartoitus painevesireaktorityyppisessä ydinvoimalaitoksessa

Työn tavoitteena on kartoittaa painevesireaktorityyppisen ydinvoimalaitoksen prosessihyötysuhteen parantamiskohteita. Aluksi kirjallisuudesta etsitään hyötysuhteen parantamiskeinoja ideaalisessa höyryvoimalaitosprosessissa. Näistä valitaan sopivimmat tarkastelun kohteeksi todellisessa voimalaitoksessa: syöttöveden esilämmityksen tehostaminen väliottohöyryvirtausta kasvattamalla ja syöttöveden esilämmittimen lämmönsiirtopintaa lisäämällä. Tarkastelussa pyritään löytämään paras mahdollinen hyötysuhde väliottohöyrylinjojen putkikokoa sekä esilämmittimien putkien lukumäärää muuttamalla. Diskreetin optimoinnin iteraatioaskel määritetään hyötysuhteen osittaisderivaattojen avulla. Tehtäviä muutoksia simuloidaan APROS-simulointiohjelmalla, jossa käytetään Loviisan voimalaitoksesta tehtyä mallia VVER-440. Työssä havaittiin, että pelkkiä väliottohöyrylinjojen putkikokoja – ja massavirtaa – kasvattamalla Loviisan voimalaitoksen hyötysuhdetta voidaan parantaa parhaimmillaan 32,75%:sta 32,85%:iin. Syöttöveden esilämmittimien lämmönsiirtopintaa lisäämällä saadaan suurempi parannus hyötysuhteeseen: 32,75%:sta 32,99%:iin. Näissä tapauksissa muutettiin kaikkia väliottohöyrylinjoja tai syöttöveden esilämmittimien lämpöpintoja. Työssä tarkasteltiin myös joitakin pienempiä muutoskohteita, joista paras hyötysuhteen kasvu saatiin korkeapaine-esilämmittimien lämmönsiirtopintaa kasvattamalla sekä toisen väliottohöyrylinjan (RD12) ja sitä vastaavan syöttöveden esilämmittimen muutosten yhteisvaikutuksena.

Model based study of a calcium oxide looping process for post-combustion carbon dioxide capture

Calcium oxide looping is a carbon dioxide sequestration technique that utilizes the partially reversible reaction between limestone and carbon dioxide in two interconnected fluidised beds, carbonator and calciner. Flue gases from a combustor are fed into the carbonator where calcium oxide reacts with carbon dioxide within the gases at a temperature of 650 ºC. Calcium oxide is transformed into calcium carbonate which is circulated into the regenerative calciner, where calcium carbonate is returned into calcium oxide and a stream of pure carbon dioxide at a higher temperature of 950 ºC. Calcium oxide looping has proved to have a low impact on the overall process efficiency and would be easily retrofitted into existing power plants. This master’s thesis is done in participation to an EU funded project CaOling as a part of the Lappeenranta University of Technology deliverable, reactor modelling and scale-up tools. Thesis concentrates in creating the first model frame and finding the physically relevant phenomena governing the process.

Dieselmoottorisen kaupunkilinja-auton muuttaminen sarjahybridiajoneuvoksi

Tutkimus on pohjustusta Lappeenrannan teknillisen yliopiston Green Campus–hankkeessa tulevaisuudessa mahdollisesti rakennettavalle Cambus–hybridibussille ja siihen liittyvälle muutostyölle. Tässä tutkimuksessa käsitellään asioita, joita kohdataan kun tavallinen dieselkäyttöinen linja–auto muutetaan hybridiajoneuvoksi. Työ sisältää teoriaosuuden, jossa esitellään peruskomponentteja esimerkiksi moottoreiden ja energianvarastointitekniikoiden osalta sekä uusimpia kehityskohteita polttomoottoreiden osalta. Tutkimuksessa on myös vertailtu erilaisia hybridivaihtoehtoja sekä käsitelty mm. tasauspyörästön välityssuhteen ja vaihteiston vaikutusta bussin teoreettiseen suorituskykyyn. Tehdyn tutkimustyön perusteella on hahmoteltu eräs mahdollinen sarjahybridibussin voimansiirtolinja esimerkkikomponentteineen. Tutkimuksessa esitetään myös laskelmia järjestelmän teoreettisesta polttoaineenkulutuksesta jarrutusenergian talteenotto huomioiden perinteiseen kaupunkilinja-autoon verrattuna.

Energy storage in electric drive system

In recent years the environmental issues and the energy saving have become increasingly import in modern society where industry is the major emission factor and energy consumer. Generally, most of the total energy consumption is caused by electrical drives used in industrial applications and thus improving the performance of electrical drives give an opportunity to improve the energy efficiency. In this Master Thesis improving the energy efficiency in different electrical drives is clarified with different cases: regenerative braking in the electric grid or recovery of the braking energy into an energy storage. In addition, as an example, the energy consumption of an elevator is analyzed by measurements. From these measurement results it can be estimated how much the share of the standby energy consumption is from the total energy consumption and how much regenerative energy is available. The latter part of the thesis concentrates on determination of the properties of lithium iron phosphate battery with measurements.

Identification and characterization of new genes and pathways regulating spermatogonial cell fate

Spermatogenesis, i.e sperm production in the seminiferous tubules of the testis, is a complex process that takes over one month to complete. Life-long ability of sperm production ultimately lies in a small population of undifferentiated cells, called spermatogonial stem cells (SSCs). These cells give rise to differentiating spermatogonia, which are committed to mature into spermatozoa. SSCs represent a heterogeneous population of cells and many aspects of their basic biology are still unknown. Understanding the mechanisms behind the cell fate decision of these cells is important to gain more insights into the causes of infertility and testis cancer. In addition, an interesting new aspect is the use of testis-derived stem cells in regenerative medicine. Our data demonstrated that adult mouse testis houses a population of Nanog-expressing spermatogonia. Based on mRNA and protein analysis these cells are enriched in stage XII of the mouse seminiferous epithelial cycle. The cells derived from this stage have the highest capacity to give rise to ES cell-like cells which express Oct4 and Nanog. These cells are under tight non- GDNF regulation but their fate can be dictated by activating p21 signalling. Comparative studies suggested that these cells are regulated like ES cells. Taken together these data imply that pluripotent cells are present in the adult mammalian testis. CIP2A (cancerous inhibitor of PP2A) has been associated with tumour aggressiveness and poor prognosis. In the testis it is expressed by the descendants of stem cells, i.e. the spermatogonial progenitor cells. Our data suggest that CIP2A acts upstream of PLZF and is needed for quantitatively normal spermatogenesis. Classification of CIP2A as a cancer/testis gene makes it an attractive target for cancer therapy. Study on the CIP2A deficient mouse model demonstrates that systemic inhibition of CIP2A does not severely interfere with growth and development or tissue or organ function, except for the spermatogenic output. These data demonstrate that CIP2A is required for quantitatively normal spermatogenesis. Hedgehog (Hh) signalling is involved in the development and maintenance of many different tissues and organs. According to our data, Hh signalling is active at many different levels during rat spermatogenesis: in spermatogonia, spermatocytes and late elongating spermatids. Localization of Suppressor of Fused (SuFu), the negative regulator of the pathway, specifically in early elongating spermatids suggests that Hh signalling needs to be shut down in these cells. Introduction of Hh signalling inhibitor resulted in an increase in germ cell apoptosis. Follicle-stimulating hormone (FSH) and inhibition of receptor tyrosine kinases resulted in down-regulation of Hh signalling. These data show that Hh signalling is under endocrine and paracrine control and it promotes germ cell survival.

Pluripotency and genetic stability of human pluripotent stem cells

Pluripotent cells have the potential to differentiate into all somatic cell types. As the adult human body is unable to regenerate various tissues, pluripotent cells provide an attractive source for regenerative medicine. Human embryonic stem cells (hESCs) can be isolated from blastocyst stage embryos and cultured in the laboratory environment. However, their use in regenerative medicine is restricted due to problems with immunosuppression by the host and ethical legislation. Recently, a new source of pluripotent cells was established via the direct reprogramming of somatic cells. These human induced pluripotent stem cells (hiPSCs) enable the production of patient specific cell types. However, numerous challenges, such as efficient reprogramming, optimal culture, directed differentiation, genetic stability and tumor risk need to be solved before the launch of therapeutic applications. The main objective of this thesis was to understand the unique properties of human pluripotent stem cells. The specific aims were to identify novel factors involved in maintaining pluripotency, characterize the effects of low oxygen culture on hESCs, and determine the high resolution changes in hESCs and hiPSCs during culture and reprogramming. As a result, the previously uncharacterized protein L1TD1 was determined to be specific for pluripotent cells and essential for the maintenance of pluripotency. The low oxygen culture supported undifferentiated growth and affected expression of stem cell associated transcripts. High resolution screening of hESCs identified a number of culture induced copy number variations and loss of heterozygosity changes. Further, screening of hiPSCs revealed that reprogramming induces high resolution alterations. The results obtained in this thesis have important implications for stem cell and cancer biology and the therapeutic potential of pluripotent cells.

Acidic dissolution of iron oxides and regeneration of a ceramic filter medium

The dewatering of iron ore concentrates requires large capacity in addition to producing a cake with low moisture content. Such large processes are commonly energy intensive and means to lower the specific energy consumption are needed. Ceramic capillary action disc filters incorporate a novel filter medium enabling the harnessing of capillary action, which results in decreased energy consumption in comparison to traditional filtration technologies. As another benefit, the filter medium is mechanically and chemically more durable than, for example, filter cloths and can, thus, withstand harsh operating conditions and possible regeneration better than other types of filter media. In iron ore dewatering, the regeneration of the filter medium is done through a combination of several techniques: (1) backwashing, (2) ultrasonic cleaning, and (3) acid regeneration. Although it is commonly acknowledged that the filter medium is affected by slurry particles and extraneous compounds, published research, especially in the field of dewatering of mineral concentrates, is scarce. Whereas the regenerative effect of backwashing and ultrasound are more or less mechanical, regeneration with acids is based on chemistry. The chemistry behind the acid regeneration is, naturally, dissolution. The dissolution of iron oxide particles has been extensively studied over several decades but those studies may not necessarily be directly applicable in the regeneration of the filter medium which has undergone interactions with the slurry components. The aim of this thesis was to investigate if free particle dissolution indeed correlates with the regeneration of the filter medium. For this purpose, both free particle dissolution and dissolution of surface adhered particles were studied. The focus was on acidic dissolution of iron oxide particles and on the study of the ceramic filter medium used in the dewatering of iron ore concentrates. The free particle dissolution experiments show that the solubility of synthetic fine grained iron oxide particles in oxalic acid could be explained through linear models accounting for the effects of temperature and acid concentration, whereas the dissolution of a natural magnetite is not so easily explained by such models. In addition, the kinetic experiments performed both support and contradict the work of previous authors: the suitable kinetic model here supports previous research suggesting solid state reduction to be the reaction mechanism of hematite dissolution but the formation of a stable iron oxalate is not supported by the results of this research. Several other dissolution mechanisms have also been suggested for iron oxide dissolution in oxalic acid, indicating that the details of oxalate promoted reductive dissolution are not yet agreed and, in this respect, this research offers added value to the community. The results of the regeneration experiments with the ceramic filter media show that oxalic acid is highly effective in removing iron oxide particles from the surface of the filter medium. The dissolution of those particles did not, however, exhibit the expected behaviour, i.e. complete dissolution. The results of this thesis show that although the regeneration of the ceramic filter medium with acids incorporates the dissolution of slurry particles from the surface of the filter medium, the regeneration cannot be assessed purely based upon free particle dissolution. A steady state, dependent on temperature and on the acid concentration, was observed in the dissolution of particles from the surface even though the limit of solubility of free iron oxide particles had not been reached. Both the regeneration capacity and efficiency, with regards to the removal of iron oxide particles, was found to be temperature dependent, but was not affected by the acid concentration. This observation further suggests that the removal of the surface adhered particles does not follow the dissolution of free particles, which do exhibit a dependency on the acid concentration. In addition, changes in the permeability and in the pore structure of the filter medium were still observed after the bulk concentration of dissolved iron had reached a steady state. Consequently, the regeneration of the filter medium continued after the dissolution of particles from the surface had ceased. This observation suggests that internal changes take place at the final stages of regeneration. The regeneration process could, in theory, be divided into two, possibly overlapping, stages: (1) dissolution of surface-adhered particles, and (2) dissolution of extraneous compounds from within the pore structure. In addition to the fundamental knowledge generated during this thesis, tools to assess the effects of parameters on the regeneration of the ceramic filter medium are needed. It has become clear that the same tools used to estimate the dissolution of free particles cannot be used to estimate the regeneration of a filter medium unless only a robust characterisation of the order of regeneration efficiency is needed.

Regulation of self-renewal and detection of karyotypic changes of pluripotent human embryonic stem cells

Human embryonic stem cells are pluripotent cells capable of renewing themselves and differentiating to specialized cell types. Because of their unique regenerative potential, pluripotent cells offer new opportunities for disease modeling, development of regenerative therapies, and treating diseases. Before pluripotent cells can be used in any therapeutic applications, there are numerous challenges to overcome. For instance, the key regulators of pluripotency need to be clarified. In addition, long term culture of pluripotent cells is associated with the accumulation of karyotypic abnormalities, which is a concern regarding the safe use of the cells for therapeutic purposes. The goal of the work presented in this thesis was to identify new factors involved in the maintenance of pluripotency, and to further characterize molecular mechanisms of selected candidate genes. Furthermore, we aimed to set up a new method for analyzing genomic integrity of pluripotent cells. The experimental design applied in this study involved a wide range of molecular biology, genome-wide, and computational techniques to study the pluripotency of stem cells and the functions of the target genes. In collaboration with instrument and reagent company Perkin Elmer, KaryoliteTM BoBsTM was implemented for detecting karyotypic changes of pluripotent cells. Novel genes were identified that are highly and specifically expressed in hES cells. Of these genes, L1TD1 and POLR3G were chosen for further investigation. The results revealed that both of these factors are vital for the maintenance of pluripotency and self-renewal of the hESCs. KaryoliteTM BoBsTM was validated as a novel method to detect karyotypic abnormalities in pluripotent stem cells. The results presented in this thesis offer significant new information on the regulatory networks associated with pluripotency. The results will facilitate in understanding developmental and cancer biology, as well as creating stem cell based applications. KaryoliteTM BoBsTM provides rapid, high-throughput, and cost-efficient tool for screening of human pluripotent cell cultures.

Pk-yrityksen uudistumiskyvyn ja innovaatiokyvykkyyden mittaaminen

Uudistumiskyky ja innovaatiokyvykkyys edistävät uusien innovaatioiden syntymistä, mikä mahdollistaa kestävän kilpailuedun saavuttamisen. Tässä tutkimuksessa käsitellään uudistumiskykyä yhtenä merkittävänä innovaatiokyvykkyyden taustatekijänä. Pk-yritysten innovaatiokyvykkyyden mittaamisen on havaittu parantavan innovaatiokyvykkyyttä. Näin myös pk-yritysten uudistumiskyvyn sekä innovaatiokyvykkyyden mittaamisen merkitys korostuu kilpailun koventuessa markkinoilla ja sitä tulisi käyttää osana suorituskyvyn johtamista. Tutkimuksen tavoitteena oli selvittää, miten uudistumiskykyä ja innovaatiokyvykkyyttä mitataan pk-yrityksissä. Tutkimusongelmaa lähdettiin ratkaisemaan aihealueen teorian pohjalta, jota myöhemmin sovellettiin empiriaosuudessa. Empiriassa käytettiin kvalitatiivista tutkimusmenetelmää, missä haettiin vastauksia tutkimuskysymyksiin puolistrukturoidun haastattelumallin avulla. Tutkimuksen tuloksena selvisi, mihin innovaatiokyvykkyyden osa-alueisiin pk-yritykset keskittyvät mittaamisessa. Esimerkiksi pk-yritysten innovaatiokyvykkyyden mittaamisessa tulisi kiinnittää enemmän huomiota erityisesti osallistuvan johtamisen sekä ulkopuolisen tiedon merkitykseen. Kaiken kaikkiaan innovaatiokyvykkyyden mittaamisen merkitystä ja mittariston rakentamista tulisi opettaa pk-yrityksille laajemmin.