Ionic liquid mediated biomass deconstruction: from analysis challenges to fermentable sugars

Ionic liquids, ILs, have recently been studied with accelerating interest to be used for a deconstruction/fractionation, dissolution or pretreatment processing method of lignocellulosic biomass. ILs are usually utilized combined with heat. Regarding lignocellulosic recalcitrance toward fractionation and IL utilization, most of the studies concern IL utilization in the biomass fermentation process prior to the enzymatic hydrolysis step. It has been demonstrated that IL-pretreatment gives more efficient hydrolysis of the biomass polysaccharides than enzymatic hydrolysis alone. Both cellulose (especially cellulose) and lignin are very resistant towards fractionation and even dissolution methods. As an example, it can be mentioned that softwood, hardwood and grass-type plant species have different types of lignin structures leading to the fact that softwood lignin (guaiacyl lignin dominates) is the most difficult to solubilize or chemically disrupt. In addition to the known conventional biomass processing methods, several ILs have also been found to efficiently dissolve either cellulose and/or wood samples – different ILs are suitable for different purposes. An IL treatment of wood usually results in non-fibrous pulp, where lignin is not efficiently separated and wood components are selectively precipitated, as cellulose is not soluble or degradable in ionic liquids under mild conditions. Nevertheless, new ILs capable of rather good fractionation performance have recently emerged. The capability of the IL to dissolve or deconstruct wood or cellulose depends on several factors, (e.g. sample origin, the particle size of the biomass, mechanical treatments as pulverization, initial biomassto-IL ratio, water content of the biomass, possible impurities of IL, reaction conditions, temperature etc). The aim of this study was to obtain (fermentable) saccharides and other valuable chemicals from wood by a combined heat and IL-treatment. Thermal treatments alone contribute to the degradation of polysaccharides (e.g. 150 °C alone is said to cause the degradation of polysaccharides), thus temperatures below that should be used, if the research interest lies on the IL effectiveness. On the other hand, the efficiency of the IL-treatment can also be enhanced to combine other treatment methods, (e.g. microwave heating). The samples of spruce, pine and birch sawdust were treated with either 1-Ethyl-3-methylimidazolium chloride, Emim Cl, or 1-Ethyl-3-methylimidazolium acetate, Emim Ac, (or with ionized water for comparison) at various temperatures (where focus was between 80 and 120 °C). The samples were withdrawn at fixed time intervals (the main interest treatment time area lied between 0 and 100 hours). Double experiments were executed. The selected mono- and disaccharides, as well as their known degradation products, 5-hydroxymethylfurfural, 5-HMF, and furfural were analyzed with capillary electrophoresis, CE, and high-performance liquid chromatography, HPLC. Initially, even GC and GC-MS were utilized. Galactose, glucose, mannose and xylose were the main monosaccharides that were present in the wood samples exposed to ILs at elevated temperatures; in addition, furfural and 5-HMF were detected; moreover, the quantitative amount of the two latter ones were naturally increasing in line with the heating time or the IL:wood ratio.

Catalytic upgrading of biomass extractives to fine chemicals over supported ionic liquid catalysts (SILCAs)

Behovet av förnyelsebar energi ökar ständigt eftersom det finns en strävan att minska beroendet av fossila bränslen. Dessutom är tillgångar av fossila bränslen begränsade. Miljövänliga processer för bioraffinaderier erbjuder en stor möjlighet för produktion av energi, bränslen och kemikalier. Den finska och svenska skogsindustrin har en lång tradition i utnyttjandet av skogsbiomassor. Bioraffinaderier som integreras med pappers- och cellulosaindustrin kan frambringa både ekonomiska och ekologiska fördelar i framställning av traditionella och biobaserade produkter. I doktorsarbetet studerades omvandling av extraktivämnen till finkemikalier som kan användas t.ex. av läkemedelsindustrin. Extraktivämnen fås ur biomassa. I forskningsarbetet framställdes biobaserade finkemikalier med hjälp av katalysatorer som baserar sig på joniska vätskor. Biomassan består av cellulosa, hemicellulosa, lignin och extraktivämnen, vilka huvudsakligen är terpener, vaxer och fettsyror. Extraktivämen är vedens komponenter, som kan separeras ur vedmaterialet med hjälp av neutrala lösningsmedel. Joniska vätskekatalysatorer som var immobiliserade på fasta bärare utnyttjades för isomerisering av α,β-pinenoxider samt hydrogenering citral. Inverkan av joniska vätskor på katalysatorns aktivitet och reaktionernas produktfördelning undersöktes under varierande reaktionsbetingelser. Kinetiska modeller för pinenoxidens isomeriseringsreaktioner beskrev väl experimentellt upptäckta skillnader mellan olika katalysatorer. --------------------------------------------------- Uusiutuvan energian tarve on kasvussa, koska riippuvuutta fossiilisista polttoaineista pyritään vähentämään. Tämän lisäksi fossiilisten polttoaineiden varannot ovat rajalliset. Ympäristöystävälliset biojalostusprosessit ovat näin ollen suuri mahdollisuus energian, polttoaineiden ja kemikaalien tuotannossa. Suomen ja Ruotsin metsäteollisuudella on pitkät perinteet metsäbiomassojen hyödyntämisessä. Paperi- ja selluteollisuuden yhteyteen integroiduilla biojalostamoilla voidaan luoda taloudellisia ja ympäristöllisiä etuja sekä perinteisten että biopohjaisten tuotteiden valmistuksessa. Väitöstyössä on tutkittu biomassan uuteaineiden kemiallista muuntamista hienokemikaaleiksi, joita voidaan käyttää esimerkiksi lääkeaineteollisuudessa. Biopohjaisia hienokemikaaleja on valmistettu biomassan uuteaineista ionisiin nesteisiin perustuvilla katalyyteillä. Biomassa koostuu selluloosasta, hemiselluloosasta, ligniinistä sekä uuteaineista, jotka ovat pääosin terpeenejä, vahoja tai rasvahappoja. Uuteaineet ovat puun komponentteja, jotka voidaan erottaa puusta neutraalien liuottimien avulla. Kiinteän kantajan päälle immobilisoituja ionisia nestekatalyyttejä (Supported Ionic Liquid Catalyst) hyödynnettiin α,β-pineenioksidien isomerisointireaktioissa sekä sitraalin vedytysreaktioissa. Ionisten nesteiden vaikutusta katalyyttien aktiivisuuteen sekä reaktioiden tuotejakaumaan tutkittiin erilaisissa reaktio-olosuhteissa. Pineenioksidien isomerisointireaktioiden kineettiset mallit kuvasivat hyvin kokeellisesti todettuja katalyyttien eroavaisuuksia.

Membraanien kestävyys ionisessa nesteessä

Tämän diplomityön tavoitteena oli etsiä mahdollisimman hyvin ionista nestettä kestävä yleisesti kaupallisesti saatavilla oleva nano- tai ultrasuodatusmembraani. Kirjallisuusosassa on perehdytty yleisesti membraanitekniikan ja ionisten nesteiden historiaan sekä niiden ominaisuuksiin ja käyttösovelluksiin. Membraaniprosesseista on lyhyesti käyty läpi mikro-, ultra- ja nanosuodatus sekä käänteisosmoosi ja pervaporaatio. Kokeellisessa osassa tutkittiin neljäntoista kaupallisesti saatavilla olevien nano- ja ultrasuodatusmembraanien kestävyyttä ionisessa nesteessä. Tutkimuksessa käytettyjen membraanien vesi- ja malliaineliuosvuon arvoja sekä retentioita vertailtiin ennen ja jälkeen ioniselle nesteelle altistusta. Tulokset osoittivat, että polyamidista, polyeetterisulfonista ja sulfonoidusta polyeetterisulfonista valmistettujen membraanien suodatusominaisuudet muuttuivat niiden altistuessa ioniselle nesteelle. Näiden membraanien permeabiliteetit ja retentiot laskivat viikon altistuksen jälkeen merkittävästi. Erityisesti liuottimia kestäviksi suunnitellut membraanit säilyttivät erotusominaisuutensa paremmin.

Towards novel biogas upgrading processes

Biogas production has considerable development possibilities not only in Finland but all over the world since it is the easiest way of creating value out of various waste fractions and represents an alternative source of renewable energy. Development of efficient biogas upgrading technology has become an important issue since it improves the quality of biogas and for example facilitating its injection into the natural gas pipelines. Moreover, such upgrading contributes to resolving the issue of increasing CO2 emissions and addresses the increasing climate change concerns. Together with traditional CO2 capturing technologies a new class of recently emerged sorbents such as ionic liquids is claimed as promising media for gas separations. In this thesis, an extensive comparison of the performance of different solvents in terms of CO2 capture has been performed. The focus of the present study was on aqueous amine solutions and their mixtures, traditional ionic liquids, ‘switchable’ ionic liquids and poly(ionic liquid)s in order to reveal the best option for biogas upgrading. The CO2 capturing efficiency for the most promising solvents achieved values around 50 - 60 L CO2 / L absorbent. These values are superior to currently widely applied water wash biogas upgrading system. Regeneration of the solvent mixtures appeared to be challenging since the loss of initial efficiency upon CO2 release was in excess of 20 - 40 vol %, especially in the case of aqueous amine solutions. In contrast, some of the ionic liquids displayed reversible behavior. Thus, for selected “switchable” ionic and poly(ionic liquid)s the CO2 absorption/regeneration cycles were performed 3 - 4 times without any notable efficiency decrease. The viscosity issue, typical for ionic liquids upon CO2 saturation, was addressed and the information obtained was evaluated and related to the ionic interactions. The occurrence of volatile organic compounds (VOCs) before and after biogas upgrading was studied for biogas produced through anaerobic digestion of waste waters sludge. The ionic liquid [C4mim][OAc] demonstrated its feasibility as a promising scrubbing media and exhibited high efficiency in terms of the removal of VOCs. Upon application of this ionic liquid, the amount of identified VOCs was diminished by around 65 wt %, while the samples treated with the aqueous mixture of 15 wt % N-methyldiethanolamine with addition of 5 wt % piperazine resulted in 32 wt % reduction in the amounts of volatile organic compounds only.

Topochemistry of physical and chemical pretreatments of biomass as investigated by FE-SEM, XPS and ToF-SIMS

Surface chemistry is of great importance in plant biomass engineering and applications. The surface chemical composition of biomass which includes lignin, carbohydrates and extractives influences its interactions with chemical agents, such as pulp processing/papermaking chemicals, or enzymes for different purposes. In this thesis, the changes in the surface chemical composition of lignocellulosic biomass after physical modification for the improvement of resulting paper properties and chemical treatment for the enhancement of enzymatic hydrolysis were investigated. Low consistency (LC) refining was used as physical treatment of bleached softwood and hardwood pulp samples, and the surface chemistry of refined samples was investigated. The refined pulp was analysed as whole pulp while the fines-free fibre samples were characterized separately. The fines produced in LCrefining contributed to an enlarged surface specific area as well as the change of surface coverage by lignin and extractives, as investigated by X-ray photoelectron spectroscopy (XPS). The surface coverage by lignin of the whole pulp decreased after refining while the surface coverage by extractives increased both for pine and eucalyptus. In the case of pine, the removal of fines resulted in reduction of the surface coverage by extractives, while the surface coverage by lignin increased on fibre sample (without fines). In the case of eucalyptus, the surface coverage by lignin of fibre samples decreased after the removal of fines. In addition, the surface distribution of carbohydrates, lignin and extractives of pine and eucalyptus samples was determined by Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). LC-refining increased the amounts of pentose, hexose and extractives on the surface of pine samples. ToF-SIMS also gave clear evidence about xylan deposition and reduction of surface lignin distribution on the fibre of eucalyptus. However, the changes in the surface chemical composition during the physical treatment has led to an increase in the adsorption of fluorescent whitening agents (FWAs) on fibres due to a combination of electro-static forces, specific surface area of fibres and hydrophobic interactions. Various physicochemical pretreatments were conducted on wood and non-wood biomass for enhancing enzymatic hydrolysis of polysaccharides, and the surface chemistry of the pretreated and enzymatically hydrolysed samples was investigated by field emission scanning electron microscopy (FE-SEM), XPS and ToF-SIMS. A hydrotrope was used as a relatively novel pretreatment technology both in the case of wood and non-wood biomass. For comparison, ionic liquid and hydrothermal pretreatments were applied on softwood and hardwood as well. Thus, XPS analysis showed that the surface lignin was more efficiently removed by hydrotropic pretreatment compared to ionic liquid or hydrothermal pretreatments. SEM analysis also found that already at room temperature the ionic liquid pretreatments were more effective in swelling the fibres compared with hydrotropic pretreatment at elevated temperatures. The enzymatic hydrolysis yield of hardwood was enhanced due to the decrease in surface coverage of lignin, which was induced by hydrotropic treatment. However, hydrotropic pretreatment was not appropriate for softwood because of the predominance of guaiacyl lignin structure in this material. In addition, the reduction of surface lignin and xylan during pretreatment and subsequent increase in cellulose hydrolysis by enzyme could be observed from ToF-SIMS results. The characterisation of the non-wood biomass (e.g. sugarcane bagasse and common reed) treated by hydrotropic method, alkaline and alkaline hydrogen peroxide pretreatments were carried out by XPS and ToF-SIMS. According to the results, the action for the removal of the surface lignin of non-wood biomass by hydrotropic pretreatment was more significant compared to alkaline and alkaline hydrogen peroxide pretreatments, although a higher total amount of lignin could be removed by alkaline and alkaline hydrogen peroxide pretreatment. Furthermore, xylan could be remarkably more efficiently removed by hydrotropic method. Therefore, the glucan yield achieved from hydrotropic treated sample was higher than that from samples treated with alkaline or alkaline hydrogen peroxide. Through the use of ToF-SIMS, the distribution and localization of lignin and carbohydrates on the surface of ignocelluloses during pretreatment and enzymatic hydrolysis could be detected, and xylan degradation during enzymatic hydrolysis could also be assessed. Thus, based on the results from XPS and ToF-SIMS, the mechanism of the hydrotropic pretreatment in improving the accessibility of enzymes to fibre and further ameliorating of the enzymatic saccharification could be better elucidated.

Litiumin talteenotto luonnon suola-altaista ionisilla nesteillä

Uusiutuvan energian käytön lisääntyminen lisää sähkön varastoinnin tarvetta. Litiumioniakku-jen on todettu olevan oivallisia keinoja varastoida sähköä esimerkiksi sähköautojen energian-lähteeksi. Tästä syystä akkujen kysyntä kasvaa nopeaa tahtia, jolloin nykyiset litiumlähteet ei-vät enää riitä tuottamaan tarpeeksi litiumia kasvavaan tarpeeseen. Tämän vuoksi litiumin tal-teenottoon tulee valjastaa uusia litiumin lähteitä, joiden hyödynnettävyys nykyisellä tekniikalla on pienen litiumkonsentraation ja muiden alkali- ja maa-alkalimetallien läsnäolon takia vaikeaa. Tällä hetkellä litiumia otetaan talteen eniten korkean litiumpitoisuuden luonnon suolajärvistä. Nykyisin käytössä oleva litiumin erotusprosessi on hidas ja sen käyttö pienten litiumkonsent-raatioiden suola-altailla on kannattamatonta. Tehokkaampana talteenottomenetelmänä luonnon suolajärvillä nähdään litiumin selektiivinen uutto ionisilla nesteillä. Menetelmä on todettu toi-mivaksi suolajärvillä, joilla on matala litiumkonsentraatio. Uusien suolajärvien käyttöönotto ei ratkaise kaikkia litiumin talteenottoon liittyviä ongelmia, sillä suolajärvet ovat alttiita ilmastonmuutokselle, eikä niiden litiumvarannot ole ehtymättömät. Merien litiumvarantoja sen sijaan pidetään lähes ehtymättöminä. Litiumin talteenotto meristä on mahdollista ionisia nesteitä ja membraaneja hyödyntävällä elektrodialyysilaitteistolla, jolla litiumia voidaan ottaa talteen myös hyvin pienistä pitoisuuksista. Lisäksi on mahdollista, että litiumin talteenottoon yhdistetään juomaveden valmistus. Tällainen vedenpuhdistusprosessi olisi myös hyvä kestävän kehityksen näkökulmasta.

Selluloosamembraanien kehittäminen ja testaus

Tämän työn tavoitteena oli selvittää, kuinka selluloosan lisääminen vaikuttaa polysulfonirunkoisiin membraaneihin. Lisäksi työssä selvitettiin selluloosamembraanien modifiointia kitosaanilla ja bentoniitilla. Työssä muodostettiin membraanit faasi-inversiotekniikalla. Selluloosamembraanien valmistuksessa jauhettu selluloosa liuotettiin ioniseen nesteeseen. Sekä polysulfonista että selluloosasta valmistetuille membraaneille määritettiin puhdasvesivuot ja retentiot. Retention määrittämiseen käytettiin malliaineena dekstraanin vesiliuosta. Lisäksi määriteltiin polysulfonipohjaisten membraanien hydrofiilisyys tutkimalla membraanien pintojen ja vesipisaroiden välisiä kontaktikulmia. Polysulfonimembraaneihin lisätyn selluloosan havaittiin pienentävän puhdasvesivuota ja kasvattavan hydrofiilisyyttä mitä enemmän selluloosaa oli membraanimatriisissa. Kaikkien selluloosalla modifioitujen membraanien retentiot olivat suurempia kuin modifioimattoman polysulfonimembraanin. Kitosaanilla modifioitujen selluloosamembraanien valmistus ei onnistunut johtuen luultavasti kitosaanin liian suuresta partikkelikoosta. Bentoniitilla modifioitujen membraanien vuot olivat merkittävästi suuremmat sekä niiden retentiot pienemmät verrattuna modifioimattomaan selluloosamembraaniin. Tämä johtui luultavasti siitä, että bentoniitin lisääminen aiheutti membraanirakenteeseen reikiä.

Release of soil phosphorus during runoff as affected by ionic strength and temperature

Selostus: Ympäristöolosuhteiden vaikutus maan fosforin liukenemiseen pintavalunnan aikana

Implementation of population balances in simulation of gas-liquid reactors using a CFD-PBM coupled approach

In bubbly flow simulations, bubble size distribution is an important factor in determination of hydrodynamics. Beside hydrodynamics, it is crucial in the prediction of interfacial area available for mass transfer and in the prediction of reaction rate in gas-liquid reactors such as bubble columns. Solution of population balance equations is a method which can help to model the size distribution by considering continuous bubble coalescence and breakage. Therefore, in Computational Fluid Dynamic simulations it is necessary to couple CFD and Population Balance Model (CFD-PBM) to get reliable distribution. In the current work a CFD-PBM coupled model is implemented as FORTRAN subroutines in ANSYS CFX 10 and it has been tested for bubbly flow. This model uses the idea of Multi Phase Multi Size Group approach which was previously presented by Sha et al. (2006) [18]. The current CFD-PBM coupled method considers inhomogeneous flow field for different bubble size groups in the Eulerian multi-dispersed phase systems. Considering different velocity field for bubbles can give the advantageof more accurate solution of hydrodynamics. It is also an improved method for prediction of bubble size distribution in multiphase flow compared to available commercial packages.

Solid and liquid biofuels markets in Finland - a study on international biofuels trade

This study considered the current situation of solid and liquid biofuels markets and international biofuels trade in Finland and identified the challenges ofthe emerging international biofuels markets for Finland. The fact that industryconsumes more than half of the total primary energy, widely applied combined heat and power production (CHP) and a high share of biofuels in the total energy consumption are specific to the Finnish energy system. One third of the electricity is generated in CHP plants. As much as 27% of the total energy consumption ismet by using wood and peat, which makes Finland the leading country in the use of biofuels. Finland has made a commitment to maintain greenhouse gas emissions at the 1990 level at the highest during the period 2008-2012. The Finnish energypolicy aims to achieve the target, and a variety of measures are taken to promote the use of renewable energy sources and especially wood fuels. In this study, the wooden raw material streams of the forest industry were included the international biofuels trade in addition to biomass streams that are traded for energy production. In 2004, as much as 45% of the raw wood importedinto Finland ended up in energy production. The total international trading of biofuels was evaluated at 72 PJ, of which the majority, 58 PJ, was raw wood. About 22% of wood based energy in Finland originated from imported raw wood. Tall oil and wood pellets composed the largest export streams of biofuels. The annual turnover of international biofuels trade was estimated at about ¤ 90 million fordirect trade and at about ¤ 190 million for indirect trade. The forest industryas the biggest user of wood, and the producer and user of wood fuels has a central position in biomass and biofuels markets in Finland. Lately, the international aspects of Finnish biofuels markets have been emphasised as the import of rawwood and the export of wood pellets have increased. Expanding the use of biofuels in the road transportation sector would increase the international streams ofbiofuels in Finland. In coming years, the international trading of biomass for energy purposes can be expected to continue growing.

Development of filter media treatments for liquid filtration

Woven monofilament, multifilament, and spun yarn filter media have long been the standard media in liquid filtration equipment. While the energy for a solid-liquid separation process is determined by the engineering work, it is the interface between the slurry and the equipment - the filter media - that greatly affects the performance characteristics of the unit operation. Those skilled in the art are well aware that a poorly designed filter medium may endanger the whole operation, whereas well-performing filter media can make the operation smooth and economical. As the mineral and pulp producers seek to produce ever finer and more refined fractions of their products, it is becoming increasingly important to be able to dewater slurries with average particle sizes around 1 ¿m using conventional, high-capacity filtration equipment. Furthermore, the surface properties of the media must not allow sticky and adhesive particles to adhere to the media. The aim of this thesis was to test how the dirt-repellency, electrical resistance and highpressure filtration performance of selected woven filter media can be improved by modifying the fabric or yarn with coating, chemical treatment and calendering. The results achieved by chemical surface treatments clearly show that the woven media surface properties can be modified to achieve lower electrical resistance and improved dirt-repellency. The main challenge with the chemical treatments is the abrasion resistance and, while the experimental results indicate that the treatment is sufficiently permanent to resist standard weathering conditions, they may still prove to be inadequately strong in terms of actual use.From the pressure filtration studies in this work, it seems obvious that the conventional woven multifilament fabrics still perform surprisingly well against the coated media in terms of filtrate clarity and cake build-up. Especially in cases where the feed slurry concentration was low and the pressures moderate, the conventional media seemed to outperform the coated media. In the cases where thefeed slurry concentration was high, the tightly woven media performed well against the monofilament reference fabrics, but seemed to do worse than some of the coated media. This result is somewhat surprising in that the high initial specific resistance of the coated media would suggest that the media will blind more easily than the plain woven media. The results indicate, however, that it is actually the woven media that gradually clogs during the coarse of filtration. In conclusion, it seems obvious that there is a pressure limit above which the woven media looses its capacity to keep the solid particles from penetrating the structure. This finding suggests that for extreme pressures the only foreseeable solution is the coated fabrics supported by a strong enough woven fabric to hold thestructure together. Having said that, the high pressure filtration process seems to follow somewhat different laws than the more conventional processes. Based on the results, it may well be that the role of the cloth is most of all to support the cake, and the main performance-determining factor is a long life time. Measuring the pore size distribution with a commercially available porometer gives a fairly accurate picture of the pore size distribution of a fabric, but failsto give insight into which of the pore sizes is the most important in determining the flow through the fabric. Historically air, and sometimes water, permeability measures have been the standard in evaluating media filtration performance including particle retention. Permeability, however, is a function of a multitudeof variables and does not directly allow the estimation of the effective pore size. In this study a new method for estimating the effective pore size and open pore area in a densely woven multifilament fabric was developed. The method combines a simplified equation of the electrical resistance of fabric with the Hagen-Poiseuille flow equation to estimate the effective pore size of a fabric and the total open area of pores. The results are validated by comparison to the measured values of the largest pore size (Bubble point) and the average pore size. The results show good correlation with measured values. However, the measured and estimated values tend to diverge in high weft density fabrics. This phenomenon is thought to be a result of a more tortuous flow path of denser fabrics, and could most probably be cured by using another value for the tortuosity factor.

Gas-liquid mass transfer in bubbly flow: Estimation of mass transfer, bubble size and reactor performance in various applications

Gas-liquid mass transfer is an important issue in the design and operation of many chemical unit operations. Despite its importance, the evaluation of gas-liquid mass transfer is not straightforward due to the complex nature of the phenomena involved. In this thesis gas-liquid mass transfer was evaluated in three different gas-liquid reactors in a traditional way by measuring the volumetric mass transfer coefficient (kLa). The studied reactors were a bubble column with a T-junction two-phase nozzle for gas dispersion, an industrial scale bubble column reactor for the oxidation of tetrahydroanthrahydroquinone and a concurrent downflow structured bed.The main drawback of this approach is that the obtained correlations give only the average volumetric mass transfer coefficient, which is dependent on average conditions. Moreover, the obtained correlations are valid only for the studied geometry and for the chemical system used in the measurements. In principle, a more fundamental approach is to estimate the interfacial area available for mass transfer from bubble size distributions obtained by solution of population balance equations. This approach has been used in this thesis by developing a population balance model for a bubble column together with phenomenological models for bubble breakage and coalescence. The parameters of the bubble breakage rate and coalescence rate models were estimated by comparing the measured and calculated bubble sizes. The coalescence models always have at least one experimental parameter. This is because the bubble coalescence depends on liquid composition in a way which is difficult to evaluate using known physical properties. The coalescence properties of some model solutions were evaluated by measuring the time that a bubble rests at the free liquid-gas interface before coalescing (the so-calledpersistence time or rest time). The measured persistence times range from 10 msup to 15 s depending on the solution. The coalescence was never found to be instantaneous. The bubble oscillates up and down at the interface at least a coupleof times before coalescence takes place. The measured persistence times were compared to coalescence times obtained by parameter fitting using measured bubble size distributions in a bubble column and a bubble column population balance model. For short persistence times, the persistence and coalescence times are in good agreement. For longer persistence times, however, the persistence times are at least an order of magnitude longer than the corresponding coalescence times from parameter fitting. This discrepancy may be attributed to the uncertainties concerning the estimation of energy dissipation rates, collision rates and mechanisms and contact times of the bubbles.

Potentiometric titration as a method of determining the stoichiometric dissociation constants of weak acids from the thermodynamic dissociation constants of aqueous solutions at 298.15 K

The simple single-ion activity coefficient equation originating from the Debye-Hückel theory was used to determine the thermodynamic and stoichiometric dissociation constants of weak acids from data concerning galvanic cells. Electromotive force data from galvanic cells without liquid junctions, which was obtained from literature, was studied in conjuction with the potentiometric titration data relating to aqueous solutions at 298.15 K. The dissociation constants of weak acids could be determined by the presented techniques and almost all the experimental data studied could be interpreted within the range of experimental error. Potentiometric titration has been used here and the calculation methods were developed to obtain the thermodynamic and stoichiometric dissociation constants of some weak acids in aqueous solutions at 298.15 K. The ionic strength of titrated solutions were adjusted using an inert electrolyte, namely, sodium or potassium chloride. Salt content alonedetermines the ionic strength. The ionic strength of the solutions studied varied from 0.059 mol kg-1 to 0.37 mol kg-1, and in some cases up to 1.0 mol kg-1. The following substances were investigated using potentiometric titration: aceticacid, propionic acid, L-aspartic acid, L-glutamic acid and bis(2,2-dimethyl-3-oxopropanol) amine.

Liquid Packaging Board Market in China

Tämän diplomityön tavoitteena on määrittää liiketoimintailmapiiri ja markkinapotentiaali Kiinan nestepakkauskartonkimarkkinoilla. Tutkimus tukee nestepakkauskartonkivalmistajan vientitoimintoja. Pääosin käytännön tiedoista koostuva tutkimus suoritettiin keräämällä sekundaääritietoa ja haastattelemalla alan erikoisasiantuntijoita. Suuri ja kasvava väestö sekä nopeasti kehittyvä talous tukee nestepakkauskartonkimarkkinoiden kasvua Kiinassa. Viimeaikainen globalisaatio haittapuolineen saattaa kuitenkin horjuttaa poliittista ja sosiaalista tasapainoa ja tätä kautta ylellisyys hyödykkeiden kuten kartonkipakattujen tuotteiden kysyntää Kiinassa. Tuontirajoitukset Kiinaan ovat laskemassa valtion tämän hetkisen kansainvälistymispolitiikan seurauksena. Kartonki vahvistaa asemaansa kilpailevien pakkausmateriaalien joukossa. Kiinan kokonaisnestepakkauskartonkimarkkinat kasvavat vuosittain 10,7 % ja ovat vuonna 2001 noin 100 000 tonnia.