Natal : nach: map of the Colony of the Cape of Good Hope and neighbouring territories 1895

Kartta kuuluu A. E. Nordenskiöldin kokoelmaan

Is All Fair in Law and War? The Ambiguous Principle of Proportionality of Collateral Damage and the CIA Drone Attacks in Pakistan

Tutkielma käsittelee Yhdysvaltain CIAn miehittämättömiä lennokki-iskuja Pakistanissa kansainvälisen humanitaarisen oikeuden suhteellisuusperiaatteen näkökulmasta. Suhteellisuusperiaatteen mukaan aseellisista iskuista saatavan sotilaallisen hyödyn tulee olla suhteellinen verrattuna siviileille aiheutuvaan haittaan. CIAn iskuja Pakistanissa on kritisoitu, että ne eivät täytä suhteellisuusperiaatteen asettamia vaatimuksia. Tutkielmassa perehdytään ensinnäkin selvittämään ne velvollisuudet, jotka suhteellisuusperiaate asettaa hyökkääjille. Sen jälkeen CIAn lennokki-iskuja tutkitaan näiden velvollisuuksien valossa. Tutkielmassa pyritään selvittämään antaako suhteellisuusperiaatteen luomat oikeudelliset velvollisuudet riittävää suojaa Pakistanin siviileille lennokki-iskujen tuhoja vastaan. Lisäksi pyritään selvittämään, onko lennokki-iskuissa viitteitä suhteellisuusperiaatteen vastaisista iskuista. Tutkimusmenetelmänä käytetään positivistista lainopin metodia, jonka avulla selvitetään voimassa olevaa kansainvälisen humanitaarisen tapaoikeuden suhteellisuusperiaatteen sisältöä. Oikeudellisina lähteinä käytetään pääasiassa humanitaarista tapaoikeutta, mutta tulkinnallisena apuna myös kansainvälisiä sopimuksia sekä oikeuden päätöksiä. Lisäksi oikeudellinen kirjallisuus on tutkimuksessa tärkeässä asemassa. Tutkimuksessa päädytään siihen, että suhteellisuusperiaatteen asettamat velvollisuudet hyökkääjälle ovat niin epämääräiset, että ne eivät anna riittävää suojaa siviileille. Ensinnäkin hyökkääjä voi määrittää sotilaallisen hyödyn omien päämääriensä mukaisesti suhteellisuusanalyysissä. Lisäksi kynnys sille, mikä katsotaan suhteellisuusperiaatteen vastaisuudeksi on hyvin epämääräinen ja korkea. Tämän vuoksi varotoimenpiteet iskujen suunnittelussa ovat hyvin tärkeässä asemassa myös suhteellisuusanalyysissä. Kuitenkin jos hyökkääjä edes jossain määrin osoittaa, että on tehnyt iskut hyvässä uskossa niiden laillisuudesta, iskujen katsotaan yleensä olevan suhteellisuusperiaatteen mukaisia. CIAn lennokki-iskuissa Pakistanissa on viitteitä suhteellisuusperiaatteen vastaisuudesta erityisesti ”tunnusmerkki-iskujen” osalta. ”Tunnusmerkki-iskut” johtavat yleensä vain vähäiseen sotilaalliseen hyötyyn aiheuttaen silti siviiliuhreja. Lisäksi erityisesti tunnusmerkki-iskuissa edellytetään korkeampaa tarkkuutta varotoimenpiteissä. Kuitenkin useat siviiliuhrit voivat merkitä sitä, että näitä varotoimenpiteitä ei ole noudatettu iskuissa.

In search of good relationships to music : understanding aspiration and challenge in developing music school teacher practices

This study focuses on teacher practices in publicly funded music schools in Finland. As views on the aims of music education change and broaden, music schools across Europe share the challenge of developing their activities in response. In public and scholarly debate, there have been calls for increased diversity of contents and concepts of teaching. In Finland, the official national curriculum for state-funded music schools builds on the ideal that teaching and learning should create conditions which promote ‘a good relationship to music’. The meaning of this concept has been deliberately left open in order to leave room for dialogue, flexibility, and teacher autonomy. Since what is meant by ‘good’ is not defined in advance, the notion of ‘improving’ practices is also open to discussion. The purpose of the study is to examine these issues from teachers’ point of view by asking what music school teachers aim to accomplish as they develop their practices. Methodologically, the study introduces a suggestion for building empirical research on Alperson’s ‘robust’ praxial approach to music education, a philosophical theory which is strongly committed to practitioner perspectives and musical diversity. A systematic method for analysing music education practices, interpretive practice analysis, is elaborated with support from interpretive research methods originally used in policy analysis. In addition, the research design shows how reflecting conversations (a collaborative approach well-known in Nordic social work) can be fruitfully applied in interpretive research and combined with teacher inquiry. Data have been generated in a collaborative project involving five experienced music school teachers and the researcher. The empirical material includes transcripts from group conversations, data from teacher inquiry conducted within the project, and transcripts from follow-up interviews. The teachers’ aspirations can be understood as strivings to reinforce the connection between musical practices and various forms of human flourishing such that music and flourishing can sustain each other. Examples from their practices show how the word ‘good’ receives its meaning in context. Central among the teachers’ concerns is their hope that students develop a free and sustainable interest in music, often described as inspiration. I propose that ‘good relationships to music’ and ‘inspiration’ can be understood as philosophical mediators which support the transition from an indeterminate ‘interest in music’ towards specific ways in which music can become a (co-)constitutive part of living well in each person’s particular circumstances. Different musical practices emphasise different aspects of what is considered important in music and in human life. Music school teachers consciously balance between a variety of such values. They also make efforts to resist pressure which might threaten the goods they think are most important. Such goods include joy, participation, perseverance, solid musical skills related to specific practices, and a strong sense of vitality. The insights from this study suggest that when teachers are able to create inspiration, they seem to do so by performing complex work which combines musical and educational aims and makes general positive contributions to their students’ lives. Ensuring that teaching and learning in music schools remain as constructive and meaningful as possible for both students and teachers is a demanding task. The study indicates that collaborative, reflective and interdisciplinary work may be helpful as support for development processes on both individual and collective levels of music school teacher practices.

Characteristics of a good customer reference for a process equipment supplier

Työn tavoitteena oli tutkia hyvän asiakasreferenssin ominaisuuksia suodatinvalmistaja Laroxin myynnin ja huollon sekä yrityksen asiakkaiden näkökulmasta. Larox voi käyttää saatua tietoa referenssien tehokkaampaan valintaan ja hyödyntämiseen. Kaksi internet-kyselyä toteutettiin, välineenä Webropol. Alustava kysely sunnattiin Laroxin myynnille ja huollolle. Kysely koostui viidestä kategoriasta asiakasreferenssejä, joiden tärkeyttä arvioitiin, sekä vapaista vastauksista. Tunnistettuja hyvän asiakasreferenssin ominaisuuksia ovat hyvä suhde referenssiasiakkaaseen, positiiviset jarehelliset suosittelut asiakkaalta, referenssilaitteen hyvä toimintakyky ja asiakas joka ymmärtää huollon tärkeyden. Pääkysely suunnattiin Laroxin asiakkaille. Tilastollisilla analyyseilla tutkittiin koetun riskin mallinmuuttujien välisiä yhteyksiä. Analyysit eivät paljastaneet merkittäviä riippuvuuksia asiakasreferenssin ominaisuuksien tärkeydessä eritaustaisten vastaajien tai tilannetekijöiden välillä, mutta asiakasreferenssin ominaisuuksien faktorit tukevat mallia. Referenssilaitteiden toimintakyky vaikuttaa tärkeimmältä ja huollon tärkeys on myös merkittävä.

Laser Cutting of Austenitic Stainless Steel with a High Quality Laser Beam

The thin disk and fiber lasers are new solid-state laser technologies that offer a combinationof high beam quality and a wavelength that is easily absorbed by metal surfacesand are expected to challenge the CO2 and Nd:YAG lasers in cutting of metals ofthick sections (thickness greater than 2mm). This thesis studied the potential of the disk and fiber lasers for cutting applications and the benefits of their better beam quality. The literature review covered the principles of the disk laser, high power fiber laser, CO2 laser and Nd:YAG laser as well as the principle of laser cutting. The cutting experiments were made with thedisk, fiber and CO2 lasers using nitrogen as an assist gas. The test material was austenitic stainless steel of sheet thickness 1.3mm, 2.3mm, 4.3mm and 6.2mm for the disk and fiber laser cutting experiments and sheet thickness of 1.3mm, 1.85mm, 4.4mm and 6.4mm for the CO2 laser cutting experiments. The experiments focused on the maximum cutting speeds with appropriate cut quality. Kerf width, cutedge perpendicularity and surface roughness were the cut characteristics used to analyze the cut quality. Attempts were made to draw conclusions on the influence of high beam quality on the cutting speed and cut quality. The cutting speeds were enormous for the disk and fiber laser cutting experiments with the 1.3mm and 2.3mm sheet thickness and the cut quality was good. The disk and fiber laser cutting speeds were lower at 4.3mm and 6.2mm sheet thickness but there was still a considerable percentage increase in cutting speeds compared to the CO2 laser cutting speeds at similar sheet thickness. However, the cut quality for 6.2mm thickness was not very good for the disk and fiber laser cutting experiments but could probably be improved by proper selection of cutting parameters.

Converter-flux-based current control of voltage source PWM rectifiers - analysis and implementation

Pulsewidth-modulated (PWM) rectifier technology is increasingly used in industrial applications like variable-speed motor drives, since it offers several desired features such as sinusoidal input currents, controllable power factor, bidirectional power flow and high quality DC output voltage. To achieve these features,however, an effective control system with fast and accurate current and DC voltage responses is required. From various control strategies proposed to meet these control objectives, in most cases the commonly known principle of the synchronous-frame current vector control along with some space-vector PWM scheme have been applied. Recently, however, new control approaches analogous to the well-established direct torque control (DTC) method for electrical machines have also emerged to implement a high-performance PWM rectifier. In this thesis the concepts of classical synchronous-frame current control and DTC-based PWM rectifier control are combined and a new converter-flux-based current control (CFCC) scheme is introduced. To achieve sufficient dynamic performance and to ensure a stable operation, the proposed control system is thoroughly analysed and simple rules for the controller design are suggested. Special attention is paid to the estimationof the converter flux, which is the key element of converter-flux-based control. Discrete-time implementation is also discussed. Line-voltage-sensorless reactive reactive power control methods for the L- and LCL-type line filters are presented. For the L-filter an open-loop control law for the d-axis current referenceis proposed. In the case of the LCL-filter the combined open-loop control and feedback control is proposed. The influence of the erroneous filter parameter estimates on the accuracy of the developed control schemes is also discussed. A newzero vector selection rule for suppressing the zero-sequence current in parallel-connected PWM rectifiers is proposed. With this method a truly standalone and independent control of the converter units is allowed and traditional transformer isolation and synchronised-control-based solutions are avoided. The implementation requires only one additional current sensor. The proposed schemes are evaluated by the simulations and laboratory experiments. A satisfactory performance and good agreement between the theory and practice are demonstrated.

The laser weldability of lean duplex stainless steels

Ruostumattomien terästen hinta on kasvanut maailman laajuisen kysynnän kasvun seurauksena. Samoin on käynyt myös ruostumattomien terästen valmistukseen käytettävien seosaineiden hinnalle. Terästen valmistajat ovatkin kehittäneet lean duplex teräksiä vastatakseen hintatietoisten markkinoiden kysyntään. Näissä lean duplex teräksissä kalliita seosaineita kuten nikkeliä ja molybdeenia on korvattu typellä ja mangaanilla. Houkutteleviksi vaihtoehdoiksi perinteisille ruostumattomille teräksille lean duplex laadut tekee myös niiden hyvät lujuus- ja korroosio-ominaisuudet. Kirjallisuus osio esittelee lasereiden toimintaperiaatteen. Myös avaimenreikähitsauksen periaate on esitetty. Ruostumattomien terästen yleisimmät seosaineet ovat esitelty, kuten myös syy niiden seostamiseen. Ruostumattomat duplex-teräkset on esitelty samoin kuin lean duplex teräkset. Kokeellisen osion koehitsit hitsattiin osin samalla tuotantolinjalla lopputuotteen kanssa ja osin laboratoriossa. Koemateriaaleina olivat lean duplex teräkset 1.4162 ja 1.4362 joiden materiaalipaksuudet olivat 1.2 mm ja 1.5 mm. Hitsatuille lamelleille tehtiin painetestaus. Makroskopiaa ja valomikroskopiaa käytettiin koehitsien arvioinnissa kuten myös ristivetokoetta. Kiinnostavimmista hitseistä määritettiin myös faasisuhde. Lean duplex teräs 1.4362 havaittiin sopivammaksi laaduksi tämän kaltaisessa sovelluksessa, mutta myös laatu 1.4162 täyttää sovelluksen hitsille asetetut vaatimukset, tosin huomattavasti pienemmässä parametri ikkunassa. Valittu menetelmä faasisuhteen määrittämiseen osoittautui epätarkaksi, joten faasisuhteen osalta tämän tutkimuksen tulokset ovat vain suuntaa-antavia.

Compulsory licensing of standard-essential patents and injunctive relief as abuse of dominant position in violation of Article 102 TFEU

When a dominant undertaking holding a standard-essential patent uses its exclusive right to the IP to seek injunctions against those wishing to produce either de jure or de facto standard compliant products, it creates a conflict between the exclusive right to the use of the IP on the one hand and the possible abuse of dominance due to the exclusionary conduct on the other. The aim of the thesis is to focus on the issues concerning abuse of dominance in violation of Article 102 TFEU when the holder of the standard-essential patent seeks an injunction against a would-be licensee. The thesis is mainly based on the most recent ECJ case law in Huawei and the Commission’s recent decisions in Samsung and Motorola. The case law in Europe prior to those decisions was mainly focused on the German case law from Orange Book Standard which provided IP holders great leverage due to the almost automatic granting of injunctions against infringers. The ECJ in Huawei set out the requirements for when a de jure standard-essential patent holder would not be violating Article 102 TFEU when seeking an injunction, requiring that negotiations in good faith must take place prior to the seeking of the injunction and that all offers must comply with FRAND terms, thus limiting the scope of case law derived from Orange Book Standard in Germany. The ECJ chose not to follow all of the reasoning the Commission had laid out in Samsung and Motorola which provided a more licensee-friendly approach on the matter, but rather chose a compromise between the IP holder friendly German case law and the Commission’s decisions. However, the ECJ did not disclose how FRAND terms themselves should be interpreted, but rather left it for the national courts to decide. Furthermore, the thesis strongly argues that Huawei did not change the fact that only vertically integrated IP holders who have made a FRAND declaration are subject to the terms laid out in Huawei, thus leaving non-practicing entities such as patent trolls and entities that have not made a FRAND declaration outside its scope. The resulting conclusion from the thesis is that while the ECJ in Huawei presented new exceptional circumstances for when an IP holder could be abusing its dominant position when it seeks an injunction, it still left many more questions answered, such as the meaning of FRAND and whether deception in giving a FRAND declaration is prohibited under Article 102 TFEU or not.

CO2 Laser Cutting of Particleboard, HDF and MDF

The purpose of this thesis is to reveal how the laser cutting parameters influence lasercutting of particleboard, HDF and MDF. The literature review introduces the basic principle of CO2 laser, CO2 laser equipment and its usage in cutting of wood-based materials. The experimental part focuses on the discussion and analysis ofthe test data and attempts to draw conclusions on the influence of various parameters, including laser power, focal length of the lens and cutting gas, on the cutting speed and kerf quality. The tested materials include various thicknesses of particleboard, HDF and MDF samples. A TRUMPF TLF2700 HQ laser equipment was used for the experiments. To obtain valid data, the test samples must be completely cut through without any bonding of wood fibre. The maximum cutting speed is linear dependent on the laser power in thecondition that the other parameters are constant. For each thickness of a specific material type, there is a minimum laser power for cutting. Normally, the topand bottom kerf widths increase with the enhancement of laser power. There may be a critical laser power which can generate the minimum cross-sectional kerf width. Lens of larger focal length may achieve higher cutting speed. As the focal length becomes larger, the top kerf width tends to increase while the bottom andcross-sectional kerf widths to the opposite. Of all cutting gases, oxygen can help achieve higher cutting speed. The gas pressure of nitrogen does not seem to have strong influence on the cutting result. Generally, 2 bar air is more preferable for higher cutting speed. For particleboard and MDF samples of larger thickness than 12 mm, 2 bar argon can be used to reach remarkably higher cutting speed than the 5 bar. Generally, the 190.5 mm lens can produce smallest total kerf width. The kerf sides of thicker samples are darker than the thinner ones. The sample darkness tends to be lower as laser power increased. 63.5 mm lens seemed tocause more darkness than other lens. 5 bar cutting gases can produce less dark side kerfs than 2 bar ones. Oxygen normally causes darker kerfs than other gases. No distinct differences were found between nitrogen and argon.

Fiber Laser Cutting of Mild Steel

Fiber laser for materials processing have undergone a rapid development in the pastseveral years. As fiber laser provides a combination of high beam quality and awavelength that is easily absorbed by metal surfaces, the named future laser isexpected to challenge the CO2 and Nd:YAG lasers in the area of metal cutting. This thesis studied the performance of fiber laser cutting mild steel. In the literature review part, it introduced the laser cutting principle and the principle of fiber laser including the newest development of fiber laser cuttingtechnology. Because the fiber laser cutting mild steel is a very young technology, a preliminary test was made in order to investigate effect of the cutting parameters on cut quality. Then the formal fiber laser cutting experiment was madeby using 3 mm thickness S355 steel with oxygen as assistant gas. The experimentwas focused on the cut quality with maximum cutting speed and minimum oxygen gas pressure. And the cut quality is mainly decided by the kerf width, perpendicularity tolerance, surface roughness and striation patterns. After analysis the cutting result, several conclusions were made. Although the best result got in the experiment is not perfect as predicted, the whole result of the test can be accepted. Compared with CO2 laser, a higher cutting speed was achieved by fiber laser with very low oxygen gas pressure. A further improvement about the cutting quality might be possible by proper selection of process parameters. And in order to investigate the cutting performance more clearly, a future study about cutting different thickness mild steel and different shape was recommended.

Assessing the technical competitiveness of printing papers

This dissertation studies the technical quality assessment of a printing paper. The theoretical framework basis on the customer value hierarchy concept and the product integrity concept. The experimental part of the research was divided into two phases: Interviews of the publishers and the printers and the testing of the technical quality of selected consumer magazines and a set of selected white paper samples. The revenue coming from the advertising and the revenue coming from the copy sales arethe most important factors of efficiency of the publisher. They form the highest level in the customer value hierarchy of the publisher. A printed product is profiled according to the target group and product segment. There is no absolute level of good printed quality. It can be studied only in context of the requirements set on the printed product. Publishers quality expectations are basic elements of external product integrity. The most important elements of efficiency of the printer can be summarised to reaching high production efficiency in order toattain good profitability and competitive delivery times. Printers' factors of efficiency base on the customers expectations on the consequences in use situation in the customer value hierarchy. They form the basis of internal productintegrity. The use of purely technical testing to classify printed products according to the customers' expectations proved to be only indicative at its best. The information gathered from the interviews was documented and sorted withthe help of the QFD-technique. The technical quality of two different coated paper grades were assessed based on the customer expectations and based on the best achievable quality. When customer requirements are used for the basis of assessing the technical quality of printing papers the order from best to worst is different than when comparing the papers just based on the best achievable quality.

Environmental requirements and environmental management system of boiler plant supplier

Työn tärkeimpänä tavoitteena oli edistää ympäristöjärjestelmän laatimista Kvaerner Pulping, Power divisioonan Kattilat-liiketoimintayksikölle. Lisäksi tavoitteena oli tarkastella yritykseen kohdistuvia ympäristövaatimuksia ja niiden vaikutusta yrityksen toimintaan. Aluksi työssä tarkasteltiin ympäristöjärjestelmästandardien sisältöjä ja niiden eroja. Työssä käsiteltiin myös erilaisia elinkaarijohtamisen malleja, joita voidaan hyödyntää yrityksen kokonaisvaltaisessa ympäristöjärjestelmässä. Työssä tarkasteltiin myös sidosryhmien vaikutusta yrityksen ympäristötoimintaan. Kattilalaitostoimittajan tärkeimpiä asiakkaita ovat sellu- ja paperiteollisuus. Näihin yrityksiin on kohdistunut runsaan kymmenen vuoden aikana paineita ympäristötoiminnan tehostamiseksi. Tämän kehityksen seurauksena vastaavat tehostamispaineet ovat siirtymässä myös alihankkijoille, kuten kattilaitostoimittajille. Tehokkaan ympäristöjohtamisen takaamiseksi työssä määriteltiin ympäristövastuut ja –valtuudet sekä ympäristöpäämäärät ja –tavoitteet. Lisäksi tunnistettiin yrityksen toimintaan liittyvät ympäristönäkökohdat ja –riskit. Työn yhteydessä laadittiin ympäristöjärjestelmän luonnos, ja se sisältää jatkuvan parantamisen periaatteen. Työn yhteydessä laadittiin lisäksi Kvaerner Pulping Oy:n koelaitokselle ympäristölupahakemus. Työssä on kuvattu koelaitosta ja sen ympäristölupahakemukseen liittyviä asioita esimerkkinä parantuneesta ympäristöasioiden hoidosta.

Electrical characteristics of eddy current position sensor

In the thesis the principle of work of eddy current position sensors and the main cautions that must be taken into account while sensor design process are explained. A way of automated eddy current position sensor electrical characteristics measurement is suggested. A prototype of the eddy current position sensor and its electrical characteristics are investigated. The results obtained by means of the automated measuring system are explained.