Printed platforms for paper-based analytical applications

Paper-based analytical technologies enable quantitative and rapid analysis of analytes from various application areas including healthcare, environmental monitoring and food safety. Because paper is a planar, flexible and light weight substrate, the devices can be transported and disposed easily. Diagnostic devices are especially valuable in resourcelimited environments where diagnosis as well as monitoring of therapy can be made even without electricity by using e.g. colorimetric assays. On the other hand, platforms including printed electrodes can be coupled with hand-held readers. They enable electrochemical detection with improved reliability, sensitivity and selectivity compared with colorimetric assays. In this thesis, different roll-to-roll compatible printing technologies were utilized for the fabrication of low-cost paper-based sensor platforms. The platforms intended for colorimetric assays and microfluidics were fabricated by patterning the paper substrates with hydrophobic vinyl substituted polydimethylsiloxane (PDMS) -based ink. Depending on the barrier properties of the substrate, the ink either penetrates into the paper structure creating e.g. microfluidic channel structures or remains on the surface creating a 2D analog of a microplate. The printed PDMS can be cured by a roll-ro-roll compatible infrared (IR) sintering method. The performance of these platforms was studied by printing glucose oxidase-based ink on the PDMS-free reaction areas. The subsequent application of the glucose analyte changed the colour of the white reaction area to purple with the colour density and intensity depending on the concentration of the glucose solution. Printed electrochemical cell platforms were fabricated on paper substrates with appropriate barrier properties by inkjet-printing metal nanoparticle based inks and by IR sintering them into conducting electrodes. Printed PDMS arrays were used for directing the liquid analyte onto the predetermined spots on the electrodes. Various electrochemical measurements were carried out both with the bare electrodes and electrodes functionalized with e.g. self assembled monolayers. Electrochemical glucose sensor was selected as a proof-of-concept device to demonstrate the potential of the printed electronic platforms.

Multispectral Analysis of Paper Production Phases

Paperitehtaissa paperin väriä arvioidaan L*a*b –arvojen perusteella. Tämä lähestymistapa ei ole tarkka ja johtaa siihen, että saman luokkaan kuuluvat paperit saatetaan havaita eri värisinä. Tässä diplomityössä tarkastellaan värien arviointia multispektraalisen kuvantamisen avulla. Menetelmän ajatuksena on verrata standardoidun heijastuman spektriä kohteena olevan paperirullan heijastuman spektriin mittaustapojen avulla. 12:n kirjallisuuteen perustuvan ja yhden tutkimusryhmämme kehittämän mittaustavan joukosta pyrittiin valitsemaan parhaat mittaustavat tutkimuksien perusteella. Mittaustavan tehokkuus tarkoittaa kykä tunnistaa eroavaisuuksia värisävyn, värikylläisyyden ja valoisuuden perusteella. Mittaustapoja tutkittiin sekä keinotekoisilla kuvilla että aidoilla paperinäytteillä. Tuloksena maksimi-minimi-, aritmeettisen keskiarvon minimi- ja geometrisen keskiarvon minimimenetelmä olivat parhaita mittaustapoja.

Hemicellulose extracted Kraft pulp as a raw material of paper

The transformation of a traditional pulp mill into an integrated forest biorefinery utilizing wood-derived biomass presents a promising opportunity for enterprise revival of the pulp and paper industry by offering new sources of revenue and significantly improved industry profitability. One proposed next generation process step for an integrated forest biorefinery is the extraction of hemicelluloses, allowing the co-production of pulp and ethanol or chemicals. The extraction of hemicelluloses, however, will likely have downstream effects on pulp quality. In the literature survey an overview of the integrated forest biorefinery and possible next generation technologies implementable in such facility were reviewed. Moreover, some hemicellulose extraction methods suitable for the co-production of pulp and hemicellulose products were looked into in more detail. Also, an overview on the significance of pulp’s hemicellulose content on papermaking properties of pulp fibers was made. In the literature it is stated that the hemicellulose content of pulp affects on many papermaking properties of pulp fibers, hornification and paper strength properties in particular. In the experimental part the goal was to investigate what effects alkaline hemicellulose extraction after bleaching has on the papermaking properties of birch Kraft pulp. It was discovered that tested pulps, normal and hemi-poor birch Kraft pulp, were different in many ways regarding to pulp properties. Differences were observed in both physical and chemical characteristics. Furthermore, clear distinctions were seen in tested paper properties, especially in strength properties, between the handsheets made from hemi-poor or normal birch Kraft pulp. Hemi-poor and normal birch Kraft pulps were also compared as a raw material of laboratory made copy paper. Based on this comparison, usage of hemi-poor birch pulp as the raw material of copy paper does not drastically deteriorate its quality.

Paper for printed electronics and functionality

Mass-produced paper electronics (large area organic printed electronics on paper-based substrates, “throw-away electronics”) has the potential to introduce the use of flexible electronic applications in everyday life. While paper manufacturing and printing have a long history, they were not developed with electronic applications in mind. Modifications to paper substrates and printing processes are required in order to obtain working electronic devices. This should be done while maintaining the high throughput of conventional printing techniques and the low cost and recyclability of paper. An understanding of the interactions between the functional materials, the printing process and the substrate are required for successful manufacturing of advanced devices on paper. Based on the understanding, a recyclable, multilayer-coated paper-based substrate that combines adequate barrier and printability properties for printed electronics and sensor applications was developed in this work. In this multilayer structure, a thin top-coating consisting of mineral pigments is coated on top of a dispersion-coated barrier layer. The top-coating provides well-controlled sorption properties through controlled thickness and porosity, thus enabling optimizing the printability of functional materials. The penetration of ink solvents and functional materials stops at the barrier layer, which not only improves the performance of the functional material but also eliminates potential fiber swelling and de-bonding that can occur when the solvents are allowed to penetrate into the base paper. The multi-layer coated paper under consideration in the current work consists of a pre-coating and a smoothing layer on which the barrier layer is deposited. Coated fine paper may also be used directly as basepaper, ensuring a smooth base for the barrier layer. The top layer is thin and smooth consisting of mineral pigments such as kaolin, precipitated calcium carbonate, silica or blends of these. All the materials in the coating structure have been chosen in order to maintain the recyclability and sustainability of the substrate. The substrate can be coated in steps, sequentially layer by layer, which requires detailed understanding and tuning of the wetting properties and topography of the barrier layer versus the surface tension of the top-coating. A cost competitive method for industrial scale production is the curtain coating technique allowing extremely thin top-coatings to be applied simultaneously with a closed and sealed barrier layer. The understanding of the interactions between functional materials formulated and applied on paper as inks, makes it possible to create a paper-based substrate that can be used to manufacture printed electronics-based devices and sensors on paper. The multitude of functional materials and their complex interactions make it challenging to draw general conclusions in this topic area. Inevitably, the results become partially specific to the device chosen and the materials needed in its manufacturing. Based on the results, it is clear that for inks based on dissolved or small size functional materials, a barrier layer is beneficial and ensures the functionality of the printed material in a device. The required active barrier life time depends on the solvents or analytes used and their volatility. High aspect ratio mineral pigments, which create tortuous pathways and physical barriers within the barrier layer limit the penetration of solvents used in functional inks. The surface pore volume and pore size can be optimized for a given printing process and ink through a choice of pigment type and coating layer thickness. However, when manufacturing multilayer functional devices, such as transistors, which consist of several printed layers, compromises have to be made. E.g., while a thick and porous top-coating is preferable for printing of source and drain electrodes with a silver particle ink, a thinner and less absorbing surface is required to form a functional semiconducting layer. With the multilayer coating structure concept developed in this work, it was possible to make the paper substrate suitable for printed functionality. The possibility of printing functional devices, such as transistors, sensors and pixels in a roll-to-roll process on paper is demonstrated which may enable introducing paper for use in disposable “onetime use” or “throwaway” electronics and sensors, such as lab-on-strip devices for various analyses, consumer packages equipped with product quality sensors or remote tracking devices.

Reklamaatioprosessin kehittäminen tavarataloketjussa

Tämän työn tavoitteena oli selvittää Sokoksen reklamaatioprosessin kehittämisessä saavutettavia etuja. Reklamaatiokäytäntö muuttui tämän työn aikana paperiversiosta sähköiseen muotoon, ja tässä on pyritty selvittämään muutosten vaikutuksia seurantaan ja ja toimintaan. Tavoitteena oli myös rakentaa prosessin seurannan kannalta tärkeitä mittareita kehityksen seurantaa varten.Sokos-ketjussa tehtiin vuonna 1999 yli 20 000 virheilmoitusta hankintayhtiöön. Näistä osa oli toimitusvirheitä ja osa tuotevirheitä. Reklamaatioiden arvoksi muodostui ostohinnoin lähes seitsemän miljoonaa markkaa. Reklamaatioiden suuresta määrästä johtuen Sokoksella katsottiin järkeväksi tehostaa reklamointia siirtymällä tekemään virheilmoitukset suoraan tietojärjestelmään ja välittämään ne sitä kautta automaattisesti hankintayhtiöön. Uuteen toimintamalliin siirryttiin 1.5.2000. Prosessissa saavutettuja etuja mitattiin tässä työssä järjestämällä henkilöstölle kysely, sekä mittaamalla ja arvioimalla ajansäästöjä. Investoinnin kannattavuutta tutkittiin erilaisten tulevaisuusnäkymien perusteella. Tutkimuksen perusteella uusi prosessi on helpottanut tekijöiden työtä, seuranta/mittaaminen on huomattavasti aiempaa tehokkaampaa, ja investointi muodostuu melko suurella todennäköisyydellä kannattavaksi tiettyjen hyvityssummiin liittyvien ehtojen täyttyessä.

Sähköinen tarkastuslista rakennusteollisuuden laadunvalvonnan tukena

Rakennusteollisuus on tunnettu useita muita aloja hitaammasta uuden teknologian käyttöönotosta. Yleisesti käytössä on hyvin perinteinen paperia ja kynää hyödyntävä tiedontallennuskäytäntö. Paperin käytössä tiedon tallennusvälineenä on useita ongelmia kuten säilytettävyys ja hallittavuus, joista päästään eroon siirtymällä sähköiseen tiedon tallennukseen. Laadun varmistamiseksi voidaan käyttää tarkastuslistoja, jotka toimivat tarkastuksien suorittajan muistin tukena. Muutettaessa tarkastuslista sähköiseen muotoon, voidaan välttyä paperisen tarkastuslistan ongelmilta, kuten käsialan tunnistamiselta ja merkintätapojen vaihtelevuudelta. Tässä diplomityössä käsitellään rakennusteollisuuden laadunhallinnan nykytilaa sekä sähköisen tarkastuslistan käyttöä rakennusteollisuuden laadunvalvonnassa. Lisäksi esitellään prototyyppi sähköisestä tarkastuslistasta osana laadunvalvontaa. Sähköinen tarkastuslista toteutetaan dynaamisesti niin, että tarkastuslistojen pohjalta on mahdollista luoda käyttöliittymä kyseessä olevan listan mukaisesti päätelaitteelle. Sähköisen tarkastuslistan prototyyppi on toteutettu WWW-sovelluspalveluna (World Wide Web), joka mahdollistaa useiden erilaisten päätelaitteiden hyödyntämisen.

Microscopic simulation of pigment coating consolidation

The control of coating layer properties is becoming increasingly important as a result of an emerging demand for novel coated paper-based products and an increasing popularity of new coating application methods. The governing mechanisms of microstructure formation dynamics during consolidation and drying are nevertheless, still poorly understood. Some of the difficulties encountered by experimental methods can be overcome by the utilisation of numerical modelling and simulation-based studies of the consolidation process. The objective of this study was to improve the fundamental understanding of pigment coating consolidation and structure formation mechanisms taking place on the microscopic level. Furthermore, it is aimed to relate the impact of process and suspension properties to the microstructure of the coating layer. A mathematical model based on a modified Stokesian dynamics particle simulation technique was developed and applied in several studies of consolidation-related phenomena. The model includes particle-particle and particle-boundary hydrodynamics, colloidal interactions, Born repulsion, and a steric repulsion model. The Brownian motion and a free surface model were incorporated to enable the specific investigation of consolidation and drying. Filter cake stability was simulated in various particle systems, and subjected to a range of base substrate absorption rates and system temperatures. The stability of the filter cake was primarily affected by the absorption rate and size of particles. Temperature was also shown to have an influence. The consolidation of polydisperse systems, with varying wet coating thicknesses, was studied using imposed pilot trial and model-based drying conditions. The results show that drying methods have a clear influence on the microstructure development, on small particle distributions in the coating layer and also on the mobility of particles during consolidation. It is concluded that colloidal properties can significantly impact coating layer shrinkage as well as the internal solids concentration profile. Visualisations of particle system development in time and comparison of systems at different conditions are useful in illustrating coating layer structure formation mechanisms. The results aid in understanding the underlying mechanisms of pigment coating layer consolidation. Guidance is given regarding the relationship between coating process conditions and internal coating slurry properties and their effects on the microstructure of the coating.

Parallella, dynamiska representationer i gymnasiefysiken : implementering av ett interaktivt datorverktyg i didaktiska situationer och uppfattning av effektivt lärande

The computer is a useful tool in the teaching of upper secondary school physics, and should not have a subordinate role in students' learning process. However, computers and computer-based tools are often not available when they could serve their purpose best in the ongoing teaching. Another problem is the fact that commercially available tools are not usable in the way the teacher wants. The aim of this thesis was to try out a novel teaching scenario in a complicated subject in physics, electrodynamics. The didactic engineering of the thesis consisted of developing a computer-based simulation and training material, implementing the tool in physics teaching and investigating its effectiveness in the learning process. The design-based research method, didactic engineering (Artigue, 1994), which is based on the theoryof didactical situations (Brousseau, 1997), was used as a frame of reference for the design of this type of teaching product. In designing the simulation tool a general spreadsheet program was used. The design was based on parallel, dynamic representations of the physics behind the function of an AC series circuit in both graphical and numerical form. The tool, which was furnished with possibilities to control the representations in an interactive way, was hypothesized to activate the students and promote the effectiveness of their learning. An effect variable was constructed in order to measure the students' and teachers' conceptions of learning effectiveness. The empirical study was twofold. Twelve physics students, who attended a course in electrodynamics in an upper secondary school, participated in a class experiment with the computer-based tool implemented in three modes of didactical situations: practice, concept introduction and assessment. The main goal of the didactical situations was to have students solve problems and study the function of AC series circuits, taking responsibility for theirown learning process. In the teacher study eighteen Swedish speaking physics teachers evaluated the didactic potential of the computer-based tool and the accompanying paper-based material without using them in their physics teaching. Quantitative and qualitative data were collected using questionnaires, observations and interviews. The result of the studies showed that both the group of students and the teachers had generally positive conceptions of learning effectiveness. The students' conceptions were more positive in the practice situation than in the concept introduction situation, a setting that was more explorative. However, it turned out that the students' conceptions were also positive in the more complex assessment situation. This had not been hypothesized. A deeper analysis of data from observations and interviews showed that one of the students in each pair was more active than the other, taking more initiative and more responsibilityfor the student-student and student-computer interaction. These active studentshad strong, positive conceptions of learning effectiveness in each of the threedidactical situations. The group of less active students had a weak but positive conception in the first iv two situations, but a negative conception in the assessment situation, thus corroborating the hypothesis ad hoc. The teacher study revealed that computers were seldom used in physics teaching and that computer programs were in short supply. The use of a computer was considered time-consuming. As long as physics teaching with computer-based tools has to take place in special computer rooms, the use of such tools will remain limited. The affordance is enhanced when the physical dimensions as well as the performance of the computer are optimised. As a consequence, the computer then becomes a real learning tool for each pair of students, smoothly integrated into the ongoing teaching in the same space where teaching normally takes place. With more interactive support from the teacher, the computer-based parallel, dynamic representations will be efficient in promoting the learning process of the students with focus on qualitative reasoning - an often neglected part of the learning process of the students in upper secondary school physics.

Rakennustarkastuksen mobiilityökalun suunnittelu ja toteuttaminen

Rakennusteollisuuden prosessit ovat vielä usein paperipohjaisia, mikä aiheuttaa työmaiden luonteesta johtuen tiedon hajaantumista, hidastaa tiedon siirtymistä ja vaikeuttaa tiedon käsittelyä. Työmaiden väliaikaisilla konttoreilla tiedon määrä voi nousta hallitsemattoman suureksi, mikä haittaa ja hidastaa työnjohdon päätöksentekoa. Käyttämällä sähköisiä työkaluja tiedon keräämistä, keskittämistä ja siirtoa voidaan tehostaa. Projektin tavoitteeksi otettiin teollisuuden laadunvalvonnan tarkastusprosessin tehostaminen ajallisesti käyttämällä tarkastustyöhön sähköistä tarkastuspöytäkirjaa. Tätä varten suunniteltiin sähköinen tarkastusjärjestelmä, joka koostuu kolmesta erillisestä osasta: Tarkastajan mukana kulkeva mobiililaite, jolle tallennetaan suoraan tarkastuksen laatutietoa, palvelinkone avustamaan tiedonsiirrossa ja –varastoinnissa sekä työpöytäsovellus työnjohdon tarpeisiin. Järjestelmää testattiin sähköalan asennuksia tekevässä yrityksessä osana yrityksen normaalia tarkastustyötä. Verrattuna paperiseen pöytäkirjaan sähköinen tarkastusjärjestelmä nopeutti prosessia moninkertaisesti. Nopeustesteissä havaittiin kuitenkin, että valittu tiedon synkronointikirjasto oli järjestelmän tarpeisiin liian hidas. Järjestelmä saavutti sille asetetut tavoitteet tehostamalla prosessia ajallisesti, mutta järjestelmässä on vielä osa-alueita, jotka tarvitsevat jatkokehittämistä.

Methods for Region Based Paper Surface Roughness Measurement

Paperin pinnan karheus on yksi paperin laatukriteereistä. Sitä mitataan fyysisestipaperin pintaa mittaavien laitteiden ja optisten laitteiden avulla. Mittaukset vaativat laboratorioolosuhteita, mutta nopeammille, suoraan linjalla tapahtuville mittauksilla olisi tarvetta paperiteollisuudessa. Paperin pinnan karheus voidaan ilmaista yhtenä näytteelle kohdistuvana karheusarvona. Tässä työssä näyte on jaettu merkitseviin alueisiin, ja jokaiselle alueelle on laskettu erillinen karheusarvo. Karheuden mittaukseen on käytetty useita menetelmiä. Yleisesti hyväksyttyä tilastollista menetelmää on käytetty tässä työssä etäisyysmuunnoksen lisäksi. Paperin pinnan karheudenmittauksessa on ollut tarvetta jakaa analysoitava näyte karheuden perusteella alueisiin. Aluejaon avulla voidaan rajata näytteestä selvästi karheampana esiintyvät alueet. Etäisyysmuunnos tuottaa alueita, joita on analysoitu. Näistä alueista on muodostettu yhtenäisiä alueita erilaisilla segmentointimenetelmillä. PNN -menetelmään (Pairwise Nearest Neighbor) ja naapurialueiden yhdistämiseen perustuvia algoritmeja on käytetty.Alueiden jakamiseen ja yhdistämiseen perustuvaa lähestymistapaa on myös tarkasteltu. Segmentoitujen kuvien validointi on yleensä tapahtunut ihmisen tarkastelemana. Tämän työn lähestymistapa on verrata yleisesti hyväksyttyä tilastollista menetelmää segmentoinnin tuloksiin. Korkea korrelaatio näiden tulosten välillä osoittaa onnistunutta segmentointia. Eri kokeiden tuloksia on verrattu keskenään hypoteesin testauksella. Työssä on analysoitu kahta näytesarjaa, joidenmittaukset on suoritettu OptiTopolla ja profilometrillä. Etäisyysmuunnoksen aloitusparametrit, joita muutettiin kokeiden aikana, olivat aloituspisteiden määrä ja sijainti. Samat parametrimuutokset tehtiin kaikille algoritmeille, joita käytettiin alueiden yhdistämiseen. Etäisyysmuunnoksen jälkeen korrelaatio oli voimakkaampaa profilometrillä mitatuille näytteille kuin OptiTopolla mitatuille näytteille. Segmentoiduilla OptiTopo -näytteillä korrelaatio parantui voimakkaammin kuin profilometrinäytteillä. PNN -menetelmän tuottamilla tuloksilla korrelaatio oli paras.

The Boundaries of a Firm in the Pulp and Paper Industry: Complementarities of the Resource-Based View and Transaction Cost Economics

Tämän tutkimuksen tarkoituksena on tutkia sellu- ja paperiteollisuuden toimintojen luonnetta sekä miten yrityksen rajapinnat ovat muodostuneet ko. teollisuudenalalla. Tutkimus on eksploratiivinen ja luonteeltaan kvalitatiivinen. Tutkimuksen aineisto kerättiin yrityksissä tehdyillä teemahaastatteluilla. Sellu- ja paperitehtaan toimintojen analysoinnissa käytetään resurssiperusteista näkemystä ja transaktiokustannusteoriaa. Tutkimuksen yritysten rakennetta voidaan pitää varsin konservatiivisena. Teoreettinen kehys pystyi selittämään varsinaisen tuotannon järjestämistä varsin hyvin. Tukitoiminnoissa löytyi ristiriitoja teorian ja todellisuuden välillä. Tuotantotoiminnot kannattaa pitää yrityksen sisällä, koska ne täyttävät VRIN-attribuutit ja niihin liittyy korkeita transaktiokustannuksia. Suurin osa tukitoiminnoista voidaan luokitella triviaaleiksi. Joitain tukitoimintoja voidaan kuitenkin luokitella strategisesti tärkeiksi, ja voidaan päätellä, että ne pitäisi pitää yrityksen sisällä. Tässä suhteessa tulokset olivat kuitenkin ristiriitaisia, ja lisätutkimuksia tarvittaisiin lopullisten johtopäätösten tekemiseen.

The Reflections of Strategic Orientation on profitability - A resource-based study in pulp and paper industry

Tutkielman tavoitteena oli analysoida erilaisia strategisia orientaatioita sellu- ja paperiteollisuudessa. Sellu- ja paperiteollisuus on kohtaamassa strategisia haasteita, jotka ulottuvat syvälle sen rakenteisiin. Yritykset ovat valinneet erilaisia lähestymistapoja organisoidessaan tuotantoa ja kansainvälistä arvoketjuaan tässä muuttuvassa ympäristössä. Tutkimukseen valittiin 30 suurinta sellu- ja paperiteollisuudessa toimivaa yritystä ja mahdollisia syitä kannattavuuseroihin yritysten välillä analysoitiin. Yritysten strategista orientaatiota tarkasteltiin vertailemalla muun muassa seuraavia tekijöitä: vertikaalinen integraatioaste, tuotevalikoiman laajuus, tuotantokapasiteetin levinneisyys ja tuotantokapasiteetin ikä. Kannattavuutta mitattiin erilaisilla talouden tunnusluvuilla (liikevoitto, oman pääoman tuotto-%, koko pääoman tuotto-%). Tulosten mukaan yrityksiä voidaan ryhmitellä strategisen orientaation perusteella ja ryhmien välillä on kannattavuuseroja.

Quality potential of DIP and hardwood CTMP based raw materials in woodcontaining printing paper

The objective of the thesis was to define the quality potential of DIP and hardwood CTMP based raw material furnish for a printing paper production and to define the end product's pulp-based boundary conditions especially when thinking of Chinese markets. Although the Chinese paper industry expands rapidly, the production of some paper grades is still exiguous. Especially the softwood resources are limited in Asia, thus the purpose of the thesis was to find out the possibilities to produce printing paper in China from local raw materials. Bleached CTMP can be produced, for example, from fast-growing hardwood species like eucalyptus and poplar. Therefore in this thesis it was examined if good quality printing paper is possible to produce by using deinked pulp and hardwood CTMP based furnish. In the first section of experimental part, various deinked pulps and chemithermomechanical pulps were compared. The deinked pulps were from China, Central Europe and Finland. Central European was made for magazine papers, and the Chinese as well as the Finnish pulps were made for newsprints. Two of the BCTMPs were from China and those both were made from poplar, whereas one BCTMP was made from eucalyptus in a pilot plant. There were significant differences especially between BCTMPs and their paper properties. In the second section of experimental part, the deinked pulp and eucalyptus BCTMP were blended to produce handsheets. The results show that producing the highest quality printing paper would be difficult from these raw materials. Deinked pulp affected especially the strength and optical properties as well as calender blackening. The BCTMP was found to have effects mostly on the smoothness, strength and optical properties as well as calender blackening.

Engendering Group Support Based Foresight for Capital Intensive Manufacturing Industries - Case Paper and Steel Industry Scenarios by 2018

In recent times of global turmoil, the need for uncertainty management has become ever momentous. The need for enhanced foresight especially concerns capital-intensive industries, which need to commit their resources and assets with long-term planning horizons. Scenario planning has been acknowledged to have many virtues - and limitations - concerning the mapping of the future and illustrating the alternative development paths. The present study has been initiated to address both the need of improved foresight in two capital-intensive industries, i.e. the paper and steel industries and the imperfections in the current scenario practice. The research problem has been approached by engendering a problem-solving vehicle, which combines, e.g. elements of generic scenario process, face-to-face group support methods, deductive scenario reasoning and causal mapping into a fully integrated scenario process. The process, called the SAGES scenario framework, has been empirically tested by creating alternative futures for two capital-intensive industries, i.e. the paper and steel industries. Three scenarios for each industry have been engendered together with the identification of the key megatrends, the most important foreign investment determinants, key future drivers and leading indicators for the materialisation of the scenarios. The empirical results revealed a two-fold outlook for the paper industry, while the steel industry future was seen as much more positive. The research found support for utilising group support systems in scenario and strategic planning context with some limitations. Key perceived benefits include high time-efficiency, productivity and lower resource-intensiveness. Group support also seems to enhance participant satisfaction, encourage innovative thinking and provide the users with personalised qualitative scenarios.

Effect of forest-based biofuels production on carbon footprint, Case: Integrated LWC paper mill

International energy and climate strategies also set Finland’s commitments to increasing the use of renewable energy sources and reducing greenhouse gas emissions. The target can be achieved by, for example, increasing the use of energy wood. Finland’s forest biomass potential is significant compared with current use. Increased use will change forest management and wood harvesting methods however. The thesis examined the potential for integrated pulp and paper mills to increase bioenergy production. The effects of two bioenergy production technologies on the carbon footprint of an integrated LWC mill were studied at mill level and from the cradle-to-customer approach. The LignoBoost process and FT diesel production were chosen as bioenergy cases. The data for the LignoBoost process were obtained from Metso and for the FT diesel process from Neste Oil. The rest of the information is based on the literature and databases of the KCL-ECO life-cycle computer program and Ecoinvent. In both case studies, the carbon footprint was reduced. From the results, it can be concluded that it is possible to achieve a fossil-fuel-free pulp mill with the LignoBoost process. By using steam from the FT diesel process, the amount of auxiliary fuel can be reduced considerably and the bark boiler can be replaced. With a choice of auxiliary fuels for use in heat production in the paper mill and the production methods for purchased electricity, it is possible to affect the carbon footprints even more in both cases.