Computational studies of deformation in stainless steel rings due to torch heating

A support ring of AISI 304L stainless steel that holds vertical, parallel wires arranged in a circle forming a cylinder is studied. The wires are attached to the ring with heat-induced shrinkage. When the ring is heated with a torch the heat affected zone tries to expand while the adjacent cool structure obstructs the expansion causing upsetting. During cooling, the ring shrinks smaller than its original size clamping the wires. The most important requirement for the ring is that it should be as round as possible and the deformations should occur as overall shrinkage in the ring diameter. A three-dimensional nonlinear transient sequential thermo-structural Abaqus model is used together with a Fortran code that enters the heat flux to each affected element. The local and overall deformations in one ring inflicted by the heating are studied with a small amount of inspection on residual stresses. A variety of different cases are chosen to be studied with the model constructed to provide directional knowledge; torch flux with the means of speed, location of the wires, heating location and structural factors. The decrease of heating speed increases heat flux that rises the temperature increasing shrinkage. In a single progressive heating uneven distribution of shrinkage appears to the start/end region that can be partially fixed with using speeded heating’s to strengthen the heating of that region. Location of the wires affect greatly to the caused shrinkage unlike heating location. The ring structure affects also greatly to the shrinkage; smaller diameter, bigger ring height, thinner thickness and greater number of wires increase shrinkage.

Pyridyyliryhmän sisältävien erotusmateriaalien ominaisuudet ja soveltaminen hydrometallurgiassa

Diplomityössä tutkittiin silikarunkoisen, pyridyyliryhmän sisältävän erotusmateriaalin kykyä erottaa selektiivisesti kuparia, nikkeliä, kobolttia ja kadmiumia sinkkisulfaattiliuoksista. Erotuskykyä verrattiin kolonnikokein toiseen kaupalliseen polystyreenidivinyylibentseenirunkoiseen (PS-DVB) erotusmate-riaaliin, jonka funktionaalinen ryhmä on samantyyppinen. Silikarunkoisen erotusmateriaalin happo-emäsominaisuuksia selvitettiin titrauksin. Metallien sitoutumisen kinetiikkaa ja eluointia verrattiin PS-DVB-runkoisen erotus-materiaalin kirjallisuudessa esitettyihin tuloksiin. Lisäksi määritettiin kummankin erotusmateriaalin partikkelikokojakaumat. Silikarunkoisen materiaalin havaittiin turpoavan noin 4 % muutettaessa se vapaastaemäsmuodosta happomuotoon. Turpoaminen oli huomattavasti vähäisempää kuin PS-DVB-runkoisella materiaalilla. Silikarunkoisen erotus-materiaalin titrauksen tuloksena voitiin todeta, että se oli heikosti emäksinen. Titrauskäyrä muistutti PS-DVB-runkoisen erotusmateriaalin titrauskäyrää, vaikka erotusmateriaalien protonoitumisalueet olivat hieman erilaiset. Tämä johtuu siitä, että silikarunkoisen materiaalin funktionaaliset ryhmät poikkeavat rakenteeltaan hieman PS-DVB-runkoisesta materiaalista. Tasapainokokeet osoittivat, että silikarunkoinen erotusmateriaali adsorboi tutkituista metalleista eniten kuparia ja nikkeliä ja vähiten sinkkiä. Kaikkien tutkittujen metallien eluointi silikarunkoisesta erotusmateriaalista onnistui rikkihapolla toisin kuin PS-DVB-runkoisesta erotusmateriaalista, jonka regenerointiin tarvitaan rikkihappoa tai ammoniumhydroksidia riippuen siitä, mitä metalleja siihen on ladattu.

Electromagnetic Design of a Solid Steel Rotor Motor for Demanding Operation Environments

The solid-rotor induction motor provides a mechanically and thermally reliable solution for demanding environments where other rotor solutions are prohibited or questionable. Solid rotors, which are manufactured of single pieces of ferromagnetic material, are commonly used in motors in which the rotationspeeds exceed substantially the conventional speeds of laminated rotors with squirrel-cage. During the operation of a solid-rotor electrical machine, the rotor core forms a conductor for both the magnetic flux and the electrical current. This causes an increase in the rotor resistance and rotor leakage inductance, which essentially decreases the power factor and the efficiency of the machine. The electromagnetic problems related to the solid-rotor induction motor are mostly associated with the low performance of the rotor. Therefore, the main emphasis in this thesis is put on the solid steel rotor designs. The rotor designs studied in thisthesis are based on the fact that the rotor construction should be extremely robust and reliable to withstand the high mechanical stresses caused by the rotational velocity of the rotor. In addition, the demanding operation environment sets requirements for the applied materials because of the high temperatures and oxidizing acids, which may be present in the cooling fluid. Therefore, the solid rotors analyzed in this thesis are made of a single piece of ferromagnetic material without any additional parts, such as copper end-rings or a squirrel-cage. A pure solid rotor construction is rigid and able to keep its balance over a large speed range. It also may tolerate other environmental stresses such as corroding substances or abrasive particles. In this thesis, the main target is to improve the performance of an induction motor equipped with a solid steel rotor by traditional methods: by axial slitting of the rotor, by selecting a proper rotor core material and by coating the rotor with a high-resistive stainless ferromagnetic material. In the solid steel rotor calculation, the rotor end-effects have a significant effect on the rotor characteristics. Thus, the emphasis is also put on the comparison of different rotor endfactors. In addition, a corrective slip-dependent end-factor is proposed. The rotor designs covered in this thesis are the smooth solid rotor, the axially slitted solid rotor and the slitted rotor having a uniform ferromagnetic coating cylinder. The thesis aims at design rules for multi-megawatt machines. Typically, mega-watt-size solidrotor machines find their applications mainly in the field of electric-motor-gas-compression systems, in steam-turbine applications, and in various types of largepower pump applications, where high operational speeds are required. In this thesis, a 120 kW, 10 000 rpm solid-rotor induction motor is usedas a small-scale model for such megawatt-range solid-rotor machines. The performance of the 120 kW solid-rotor induction motors is determined by experimental measurements and finite element calculations.

Oikosulkumoottorin roottorivaurioiden tunnistaminen staattorivirran avulla

Diplomityössä esitellään menetelmiä sauvarikon toteamiseksi. Työn tarkoituksena on tutkia roottorivaurioita staattorivirran avulla. Työ jaetaan karkeasti kolmeen osa-alueeseen: oikosulkumoottorin vikoihin, roottorivaurioiden tunnistamiseen ja signaalinkäsittelymenetelmiin, jonka avulla havaitaan sauvarikko. Oikosulkumoottorin vikoja ovat staattorikäämien vauriot ja roottorivauriot. Roottorikäämien vaurioita ovat roottori sauvojen murtuminen sekä roottorisauvan irtoaminen oikosulkujenkaan päästä. Roottorivaurioiden tunnistamismenetelmiä ovat parametrin arviointi ja virtaspektrianalyysi. Työn alkuosassa esitellään oikosulkumoottorien rakenne ja toiminta. Esitellään moottoriin kohdistuvia vikoja ja etsitään ratkaisumenetelmiä roottorivaurioiden tunnistamisessa. Lopuksi tutkitaan, kuinka staattorimittaustietojen perusteella saadut tulokset voidaan käsitellä FFT -algoritmilla ja kuinka FFT -algoritmi voidaan toteuttaa sulautettuna Sharc -prosessorin avulla. Työssä käytetään ADSP 21062 EZ -LAB kehitysympäristöä, jonka avulla voidaan ajaa ohjelmia RAM-sirusta, joka on vuorovaikutuksessa SHARC -laudassa oleviin laitteisiin.

High-Speed Solid-Rotor Induction Machine – Electromagnetic Calculation and Design

Within the latest decade high-speed motor technology has been increasingly commonly applied within the range of medium and large power. More particularly, applications like such involved with gas movement and compression seem to be the most important area in which high-speed machines are used. In manufacturing the induction motor rotor core of one single piece of steel it is possible to achieve an extremely rigid rotor construction for the high-speed motor. In a mechanical sense, the solid rotor may be the best possible rotor construction. Unfortunately, the electromagnetic properties of a solid rotor are poorer than the properties of the traditional laminated rotor of an induction motor. This thesis analyses methods for improving the electromagnetic properties of a solid-rotor induction machine. The slip of the solid rotor is reduced notably if the solid rotor is axially slitted. The slitting patterns of the solid rotor are examined. It is shown how the slitting parameters affect the produced torque. Methods for decreasing the harmonic eddy currents on the surface of the rotor are also examined. The motivation for this is to improve the efficiency of the motor to reach the efficiency standard of a laminated rotor induction motor. To carry out these research tasks the finite element analysis is used. An analytical calculation of solid rotors based on the multi-layer transfer-matrix method is developed especially for the calculation of axially slitted solid rotors equipped with wellconducting end rings. The calculation results are verified by using the finite element analysis and laboratory measurements. The prototype motors of 250 – 300 kW and 140 Hz were tested to verify the results. Utilization factor data are given for several other prototypes the largest of which delivers 1000 kW at 12000 min-1.

Etelä-Karjalan kuntien aineeton pääoma ja sen kehittämisen haasteet

Tämän kvalitatiivisin menetelmin suoritetun tutkimuksen tavoite on selvittää, mikä on aineettoman pääoman tila Etelä-Karjalan kunnissa ja mitkä ovat niiden aineettoman pääoman kehittämisen haasteet. Kunnat valittiin tutkimukseen kunta- ja palvelurakenneuudistuslaissa määrätyn kaupunkiseutusuunnitelman velvoitteen rajaamana. Tutkimuksen aineisto perustuu kuntien aineettoman pääoman raportteihin sekä kuntien johdolle tehtyihin puolistrukturoituihin haastatteluihin. Aineettoman pääoman raporttien analysointi on suoritettu kirjallisuusanalyysina henkilöstötilinpäätösmallia viitekehyksenä käyttäen, teoreettinen viitekehys on muodostettu kirjallisuusanalyysina aineettoman pääoman ja tietojohtamisen tutkimuskirjallisuudesta. Etelä-Karjalan kunnissa aineetonta pääomaa on osaaminen, koulu-tus, kuntien erilaiset prosessit ja järjestelmät sekä yhteistyö erilaisten sidosryhmien kanssa ja kuntien maine. Kehittämishaasteita aineettomalle pääomalle asettaa kuntien henkilöstön eläköityminen, kuntien yhteistyön lisääntyminen ja erilaisten prosessien ja järjestelmien kehittäminen.

Structural and optical properties of InAs/GaAs quantum structures

The goal of the thesis was to study fundamental structural and optical properties of InAs islands and In(Ga)As quantum rings. The research was carried out at the Department of Micro and Nanosciences of Helsinki University of Technology. A good surface quality can be essential for the potential applications in optoelectronic devices. For such device applications it is usually necessary to control size, density and arrangement of the islands. In order to study the dependence of the structural properties of the islands and the quantum rings on growth conditions, atomic force microscope was used. Obtained results reveal that the size and the density of the In(Ga)As quantum rings strongly depend on the growth temperature, the annealing time and the thickness of the partial capping layer. From obtained results it is possible to conclude that to get round shape islands and high density one has to use growth temperature of 500 ̊C. In the case of formation of In(Ga)As quantum rings the effect of mobility anisotropy is observed that so the shape of the rings is not symmetric. To exclude this effect it is preferable to use a higher annealing temperature of 570 ̊C. Optical properties were characterized by PL spectroscopy. PL emission was observed from buried InAs quantum dots and In(Ga)As quantum rings grown with different annealing time and temperature and covered with a various thickness of the partial capping layer.

Chelating Adsorbents in Purification of Hydrometallurgical Solutions

In this thesis, equilibrium and dynamic sorption properties of weakly basic chelating adsorbents were studied to explain removal of copper, nickel from a concentrated zinc sulfate solution in a hydrometallurgical process. Silica-supported chelating composites containing either branched poly(ethyleneimine) (BPEI) or 2-(aminomethyl)pyridine (AMP) as a functional group were used. The adsorbents are commercially available from Purity Systems Inc, USA as WP-1® and CuWRAM®, respectively. The fundamental interactions between the adsorbents, sulfuric acid and metal sulfates were studied in detail and the results were used to find the best conditions for removal of copper and nickel from an authentic ZnSO4 process solution. In particular, the effect of acid concentration and temperature on the separation efficiency was considered. Both experimental and modeling aspectswere covered in all cases. Metal sorption is considerably affected by the chemical properties of the studied adsorbents and by the separation conditions. In the case of WP-1, acid affinity is so high that column separation of copper, nickel and zinc has to be done using the adsorbent in base-form. On the other hand, the basicity of CuWRAM is significantly lower and protonated adsorbent can be used. Increasing temperature decreases the basicity and the metals affinity of both adsorbents, but the uptake capacities remain practically unchanged. Moreover, increasing temperature substantially enhances intra-particle mass transport and decreases viscosities thus allowing significantly higher feed flow rates in the fixed-bed separation. The copper selectivity of both adsorbents is very high even in the presence of a 250-fold excess of zinc. However, because of the basicity of WP-1, metal precipitation is a serious problem and therefore only CuWRAM is suitable for the practical industrial application. The optimum temperature for copper removal appears to be around 60 oC and an alternative solution purification method is proposed. The Ni/Zn selectivity of both WP-1 and CuWRAM is insufficient for removal of the very small amounts of nickel present in the concentrated ZnSO4 solution.

Conformal invariants

This master thesis investigates the moduli of families of curves and the capacities of the Gr¨otzsch and Teichm¨uller rings, which are applied in the main parts of this master thesis. The extremal properties of these rings are discussed in connection with the spherical symmetrization. Applications are given to the study of distortion of quasiconformal maps in the euclidean n-dimensional space.

Elemental analysis of wood materials by external millibeam thick target PIXE

PIXE (Particle Induce X-ray Emission spectrometry) was used for analysing stem bark and stem wood of Scots pine, Norway spruce and Silver birch. Thick samples were irradiated, in laboratory atmosphere, with 3 MeV protons and the beam current was measured indirectly using a photo multiplicator (PM) tube. Both point scans and bulk analyses were performed with the 1 mm diameter proton beam. In bulk analyses, whole bark and sectors of discs of the stem wood were dry ashed at 550 ˚C. The ashes were homogenised by shaking and prepared to target pellets for PIXE analyses. This procedure generated representative samples to be analysed, but the enrichment also enabled quantification of some additional trace elements. The ash contents obtained as a product of the sample preparation procedure also showed to be of great importance in the evaluation of results in environmental studies. Spot scans from the pith of pine wood outwards, showed clearly highest concentrations of manganese, calcium and zinc in the first spot irradiated, or 2-3 times higher than in the surrounding wood. For stem wood from the crown part of a pine this higher concentration level was found in the first four spots/mms, including the pith and the two following growth rings. Zinc showed increasing concentrations outwards in sapwood of the pine stem, with the over-all lowest concentrations in the inner half of the sapwood. This could indicate emigration of this element from sapwood being under transformation to heartwood. Point scans across sapwood of pine and spruce showed more distinct variations in concentrations relative to hearth wood. Higher concentrations of e.g. zinc, calcium and manganese were found in earlywood than in denser latewood. Very high concentrations of iron and copper were also seen for some earlywood increments. The ash content of stem bark is up to and order higher than for the stem wood. However, when the elemental concentration in ashes of bark and wood of the same disc were compared, these are very similar – this when trees are growing at spots with no anthropogenic contamination from the atmosphere. The largest difference was obtained for calcium which appeared at two times high concentrations in ashes of bark than in ashes of the wood (ratio of 2). Pine bark is often used in monitoring of atmospheric pollution, where concentrations in bark samples are compared. Here an alternative approach is suggested: Bark and the underlying stem wood of a pine trees are dry ashed and analysed. The elemental concentration in the bark ash is then compared to the concentration of the same element in the wood ash. Comparing bark to wood includes a normalisation for the varying availability of an element from the soil at different sites. When this comparison is done for the ashes of the materials, a normalisation is also obtained for the general and locally different enrichment of inorganic elements from wood to bark. Already a ratio >2 between the concentration in the bark ash and the concentration in the wood ash could indicate atmospheric pollution. For monitoring where bark is used, this way of “inwards” comparison is suggested - instead of comparing to results from analyses of bark from other trees (read reference areas), growing at sites with different soil and, locally, different climate conditions. This approach also enables evaluation of atmospheric pollution from sampling of only relative few individual trees –preferable during forest felling.

High-speed solid-rotor induction machine – calculation program

The aim of this thesis is to utilize the technology developed at LUT and to provide an easy tool for high-speed solid-rotor induction machine preliminary design. Computer aided design tool MathCAD has been chosen as the environment for realizing the calculation program. Four versions of the design program have been made depending on the motor rotor type. The first rotor type is an axially slitted solid-rotor with steel end rings. The next one is an axially slitted solid-rotor with copper end rings. The third machine type is a solid rotor with deep, rectangular copper bars and end rings (squirrel cage). And the last one is a solid-rotor with round copper bars and end rings (squirrel cage). Each type of rotor has its own specialties but a general thread of design is common. This paper follows the structure of the calculating program and explains some features and formulas. The attention is concentrated on the difference between laminated and solid-rotor machine design principles. There is no deep analysis of the calculation ways are presented. References for all solution methods appearing during the design procedure are given for more detailed studying. This thesis pays respect to the latest innovations in solid-rotor machines theory. Rotor ends’ analytical calculation follows the latest knowledge in this field. Correction factor for adjusting the rotor impedance is implemented. The purpose of the created design program is to calculate the preliminary dimensions of the machine according to initial data. Obtained results are not recommended for exact machine development. Further more detailed design should be done in a finite element method application. Hence, this thesis is a practical tool for the prior evaluating of the high-speed machine with different solid-rotor types parameters.

Synthesis, characterization and chemical sensor application of conducting polymers

Polymeric materials that conduct electricity are highly interesting for fundamental studies and beneficial for modern applications in e.g. solar cells, organic field effect transistors (OFETs) as well as in chemical and bio‐sensing. Therefore, it is important to characterize this class of materials with a wide variety of methods. This work summarizes the use of electrochemistry also in combination with spectroscopic methods in synthesis and characterization of electrically conducting polymers and other π‐conjugated systems. The materials studied in this work are intended for organic electronic devices and chemical sensors. Additionally, an important part of the presented work, concerns rational approaches to the development of water‐based inks containing conducting particles. Electrochemical synthesis and electroactivity of conducting polymers can be greatly enhanced in room temperature ionic liquids (RTILs) in comparison to conventional electrolytes. Therefore, poly(para‐phyenylene) (PPP) was electrochemically synthesized in the two representative RTILs: bmimPF6 and bmiTf2N (imidazolium and pyrrolidinium‐based salts, respectively). It was found that the electrochemical synthesis of PPP was significantly enhanced in bmimPF6. Additionally, the results from doping studies of PPP films indicate improved electroactivity in bmimPF6 during oxidation (p‐doping) and in bmiTf2N in the case of reduction (n‐doping). These findings were supported by in situ infrared spectroscopy studies. Conducting poly(benzimidazobenzophenanthroline) (BBL) is a material which can provide relatively high field‐effect mobility of charge carriers in OFET devices. The main disadvantage of this n‐type semiconductor is its limited processability. Therefore in this work BBL was functionalized with poly(ethylene oxide) PEO, varying the length of side chains enabling water dispersions of the studied polymer. It was found that functionalization did not distract the electrochemical activity of the BBL backbone while the processability was improved significantly in comparison to conventional BBL. Another objective was to study highly processable poly(3,4‐ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) water‐based inks for controlled patterning scaled‐down to nearly a nanodomain with the intention to fabricate various chemical sensors. Developed PEDOT:PSS inks greatly improved printing of nanoarrays and with further modification with quaternary ammonium cations enabled fabrication of PEDOT:PSS‐based chemical sensors for lead (II) ions with enhanced adhesion and stability in aqueous environments. This opens new possibilities for development of PEDOT:PSS films that can be used in bio‐related applications. Polycyclic aromatic hydrocarbons (PAHs) are a broad group of π‐conjugated materials consisting of aromatic rings in the range from naphthalene to even hundred rings in one molecule. The research on this type of materials is intriguing, due to their interesting optical properties and resemblance of graphene. The objective was to use electrochemical synthesis to yield relatively large PAHs and fabricate electroactive films that could be used as template material in chemical sensors. Spectroscopic, electrochemical and electrical investigations evidence formation of highly stable films with fast redox response, consisting of molecules with 40 to 60 carbon atoms. Additionally, this approach in synthesis, starting from relatively small PAH molecules was successfully used in chemical sensor for lead (II).

Anti-predator adaptations in aquatic environments

Predation is an important selective force that has led to the evolution of a variety of fascinating anti-predator adaptations, such as many types of protective coloration and prey behaviours. Because the evolution of life has begun in the aquatic environment and many anti-predator adaptations are found already in relative primitive taxa, it is likely that many of these adaptations evolved initially in the aquatic environment. Yet, there has been surprisingly little research on the mechanisms and function of antipredator adaptations in aquatic systems. To understand the function of anti-predator adaptations and natural selection imposed on prey appearance and behaviour, I have investigated how protective coloration can be used, either as such or together with behavioural adaptations, to manipulate predator behaviour and decrease predation risk. To this end I conducted a series of behaviour ecological laboratory experiments in which I manipulated the visual appearance of artificial backgrounds and prey items. In paper I of this thesis, I investigated background choice as an anti-predator strategy, by observing the habitat choice of the least killifish (Heterandria formosa) between pairs of artificial backgrounds, both in the presence and absence of predation threat. It has been suggested that prey could decrease their risk of being detected by predators either by preferring backgrounds into which they blend or by preferring visually complex backgrounds. The least killifish preferred a background that matched their patterning to a background that mismatched it, showing that they are able to respond to cues of visual similarity between their colour pattern and the surrounding environment. Interestingly however, in female least killifish visual complexity of the background was a more important cue for habitat safety and may override or act together with background matching when searching for a safe habitat. It is possible that in females, preference for visually complex backgrounds is associated with lower opportunity costs than preference for matching backgrounds would be. Generally, the least killifish showed stronger preference while under predation threat, indicating that their background choice behaviour is an antipredator adaptation. Many aquatic prey species have eyespots, which are colour patterns that consist of roughly concentric rings and have received their name because they for humans often resemble the vertebrate eye. I investigated the anti-predator function of eyespots against predation by fish in papers II, III and IV. Some eyespots have been suggested to benefit prey by diverting the strikes of predators away from vital parts of the prey body or towards a direction that facilitates prey escape. Although proposed over a century ago, the divertive effect of eyespots has proven to be difficult to show experimentally. In papers II and III, I tested for divertive effect of eyespots towards attacking fish by presenting artificial prey with eyespots to laboratory reared three-spined sticklebacks (Gasterosteus aculeatus). I found that eyespots strongly influenced the behaviour of attacking sticklebacks and effectively drew their strikes towards the eyespots. To further investigate this divertive effect and whether the specific shape of eyespots is important for it, I tested in paper III the response of fish also to other markings than eyespots. I found that eyespots were generally more effective in diverting the first strikes of attacking fish compared to other prey markings. My findings suggest that the common occurrence of eyespots in aquatic prey species can at least partly be explained by the divertive effect of the eyespot shape, possibly together with the relative simple developmental mechanisms underlying circular colour patterns. An eyebar is a stripe that runs through the eye, and this pattern has been suggested to obscure the real eyes of the prey by visually blending parts of the eyes and head of the prey and by creating false edges. In paper III, I show that an eyebar effectively disrupts an eyelike shape. This suggests that eyebars provide an effective way to conceal the eyes and consequently obstruct detection and recognition of prey. This experiment also demonstrates that through concealment of the eyes, eyebars could be used to enhance the divertive effect of eyespots, which can explain the common occurrence of eyebars in many species of fish that have eyespots. Larger eyespots have been shown to intimidate some terrestrial predators, such as passerine birds, either because they resemble the eyes of the predator’s own enemy or because highly salient features may have an intimidating effect. In papers II and IV, I investigated whether the occurrence of eyespots in some aquatic prey could be explained by their intimidating effect predatory fish. In paper IV, I also investigated the reason for the intimidating effect of eyelike prey marks. In paper II, I found no clear intimidating effect of eyespots, whereas in paper IV, using a different approach, I found that sticklebacks hesitated to attack towards eyelike but not towards non-eyelike marks. Importantly, paper IV therefore presents the first rigorous evidence for the idea that eye mimicry, and not merely conspicuousness, underlies the intimidating effect. It also showed that the hesitation shown by fish towards eyelike marks is partly an innate response that is reinforced by encounters with predators. Collectively, this thesis shows that prey colour pattern and the visual appearance of the habitat influence the behaviour of fish. The results demonstrate that protective coloration provides numerous distinctive ways for aquatic prey to escape predation. Thus, visual perception and behaviour of fish are important factors shaping the appearance and behaviours of aquatic prey.