Polymer surface modification by atomic layer deposition

Current industrial atomic layer deposition (ALD) processes are almost wholly confined to glass or silicon substrates. For many industrial applications, deposition on polymer substrates will be necessary. Current deposition processes are also typically carried out at temperatures which are too high for polymers. If deposition temperatures in ALD can be reduced to the level applicable for polymers, it will open new interesting areas and applications for polymeric materials. The properties of polymers can be improved for example by coatings with functional and protective properties. Although the ALD has shown its capability to operate at low temperatures suitable for polymer substrates, there are other issues related to process efficiency and characteristics of different polymers where new knowledge will assist in developing industrially conceivable ALD processes. Lower deposition temperature in ALD generally means longer process times to facilitate the self limiting film growth mode characteristic to ALD. To improve process efficiency more reactive precursors are introduced into the process. For example in ALD oxide processes these can be more reactive oxidizers, such as ozone and oxygen radicals, to substitute the more conventionally used water. Although replacing water in the low temperature ALD with ozone or plasma generated oxygen radicals will enable the process times to be shortened, they may have unwanted effects both on the film growth and structure, and in some cases can form detrimental process conditions for the polymer substrate. Plasma assistance is a very promising approach to improve the process efficiency. The actual design and placement of the plasma source will have an effect on film growth characteristics and film structure that may retard the process efficiency development. Due to the fact that the lifetime of the radicals is limited, it requires the placement of the plasma source near to the film growth region. Conversely this subjects the substrate to exposure byother plasma species and electromagnetic radiation which sets requirements for plasma conditions optimization. In this thesis ALD has been used to modify, activate and functionalize the polymer surfaces for further improvement of polymer performance subject to application. The issues in ALD on polymers, both in thermal and plasma-assisted ALD will be further discussed.

IP Telephony in Third Generation Mobile Systems: Transport Layer Dimensioning

Tämä diplomityö käsittelee kolmannen sukupolven matkaviestinjärjestelmien kuljetuskerroksen mitoitusta. Nykyisten matkapuhelinverkkojen korvaajiksi suunnitellut kolmannen sukupolven matkaviestinjärjestelmät tulevat yhdistämään perinteisen puhelinviestinnän ja uudenlaiset datapalvelut. Uudet verkot tulevat perustumaan pakettivälitteiseen tiedonsiirtoon joka mahdollistaa molempien liikennetyyppien, puheen sekä datan, siirtämisen samassa verkossa. Tämän ratkaisun uskotaan tarjoavan paremmat mahdollisuudet uusien palvelujen luomiseen ja parantavan tiedonsiirtokapasiteettia. Siirtyminen pakettivälitteiseen tiedonsiirtoon aiheuttaa kuitenkin suuria muutoksia verkkoarkkitehtuurissa. Tässä diplomityössä tarkastellaan tulevien runkoverkkojen mitoitukseen liittyviä näkökohtia sekä muodostetaan alustavia kuljetuskerroksen mitoitusohjeita. Diplomityö on tehty osaksi diplomi-insinöörin tutkintoa Lappeenrannan teknillisessä korkeakoulussa. Työ on tehty Nokia Networksin palveluksessa Helsingissä, vuoden 2000 toisella puoliskolla.

Physical layer development in third generation protocol software architecture

Diplomityön tavoitteena oli kehittää kolmannen sukupolven fyysistä protokollakerrosta matkapuhelimen ohjelmistoarkkitehtuurille. Kolmannen sukupolven matkapuhelinjärjestelmät ovat aikaisempia järjestelmiä monimutkaisempia. Ohjelmiston koon ja monimutkaisuuden sekä aikataulujen kiireellisyyden vuoksi on tullut tarve ottaa käyttöön formaaleja menetelmiä ohjelmiston kehitystyöhön. Formaalit kuvauskielet mahdollistavat tarkan, yksiselitteisen ja simuloitavissa olevan järjestelmäkuvauksen muodostamisen. Fyysinen protokollakerros tarjoaa tiedon siirtoa ylemmille protokollakerroksille. Tämän tiedonsiirron hallinta vaatii protokollakerrosten välistä viestinvälitystä. Formaaleja kuvauskieliä käyttämällä voidaan viestinvälityksen toteutusta automatisoida ja siinä tarvittavaa logiikkaa havainnollistaa. Työssä suunniteltiin, toteutettiin ja testattiin ylempien protokollakerrosten kanssa kommunikoivaa osaa fyysisestä protokollakerroksesta. Tuloksena saatiin solunvalintatoiminnallisuuden vaatiman kommunikoinnin ja tilakoneen toteutus ohjelmistoarkkitehtuurissa. Ohjelmistonkehityksen alkuvaiheiden havaittiin olevan fyysisen kerroksen suorituskyvyn kannalta merkittävässä asemassa, koska tällöin viestinvälityksen optimointi on helpointa. Formaalit kuvauskielet eivät ole sellaisenaan täysin soveltuvia tarkoin määritellyn ohjelmistoarkkitehtuurin osien kehitykseen.

Evaluation of GPRS Radio Link Control Layer in Weak RF Field

General Packet Radio Service (GPRS) mahdollistaa pakettimuotoisen tiedonsiirron GSM-verkossa. Se tarjoaa yhteyden pakettidataverkkoihin, nostaen samalla tiedonsiirtonopeutta radiorajapinnassa. Radioresurssit ovat varattuna vain silloin kun on jotain lähetettävää, tehden täten radioresurssien käytön paljon tehokkaammaksi. Tämä diplomityö keskittyy GPRS protokollaan ja erityisesti sen datapinossa olevaan Radio Link Control (RLC) kerrokseen. RLC-kerros huolehtii GPRS- puhelimen ja tukiaseman välisen yhteyden luotettavuudesta. Työn tavoitteena on tutkia RLC-kerroksen toiminnallisuutta ja sen luotettavuutta heikossa kentässä, sekä selvittää heikon kentän vaikutusta uudelleenlähetyksiin. Työn tuloksena saadaan arvio signaalin voimakkuuden sekä uudelleen lähetysten vaikutuksesta GPRS:n datansiirtonopeuteen. Tämä työ käsittelee myös lyhyesti GSM-järjestelmää, koska lukijan on näin helpompaa ymmärtää myös GPRS-järjestelmän vaatimia teknisiä muutoksia. Tämä diplomityö on tehty osana Nokia Matkapuhelimet Oyj:ssä käynnissä olevaa GPRS tuotekehitysprojektia. Työn tuloksia käytetään testauksen tukena ja niitä on käytetty apuna RLC-kerroksen luotettavuustestauksen suunnittelussa.

Gas-phase photocatalytic oxidation of volatile organic compounds

Substances emitted into the atmosphere by human activities in urban and industrial areas cause environmental problems such as air quality degradation, respiratory diseases, climate change, global warming, and stratospheric ozone depletion. Volatile organic compounds (VOCs) are major air pollutants, emitted largely by industry, transportation and households. Many VOCs are toxic, and some are considered to be carcinogenic, mutagenic, or teratogenic. A wide spectrum of VOCs is readily oxidized photocatalytically. Photocatalytic oxidation (PCO) over titanium dioxide may present a potential alternative to air treatment strategies currently in use, such as adsorption and thermal treatment, due to its advantageous activity under ambient conditions, although higher but still mild temperatures may also be applied. The objective of the present research was to disclose routes of chemical reactions, estimate the kinetics and the sensitivity of gas-phase PCO to reaction conditions in respect of air pollutants containing heteroatoms in their molecules. Deactivation of the photocatalyst and restoration of its activity was also taken under consideration to assess the practical possibility of the application of PCO to the treatment of air polluted with VOCs. UV-irradiated titanium dioxide was selected as a photocatalyst for its chemical inertness, non-toxic character and low cost. In the present work Degussa P25 TiO2 photocatalyst was mostly used. In transient studies platinized TiO2 was also studied. The experimental research into PCO of following VOCs was undertaken: - methyl tert-butyl ether (MTBE) as the basic oxygenated motor fuel additive and, thus, a major non-biodegradable pollutant of groundwater; - tert-butyl alcohol (TBA) as the primary product of MTBE hydrolysis and PCO; - ethyl mercaptan (ethanethiol) as one of the reduced sulphur pungent air pollutants in the pulp-and-paper industry; - methylamine (MA) and dimethylamine (DMA) as the amino compounds often emitted by various industries. The PCO of VOCs was studied using a continuous-flow mode. The PCO of MTBE and TBA was also studied by transient mode, in which carbon dioxide, water, and acetone were identified as the main gas-phase products. The volatile products of thermal catalytic oxidation (TCO) of MTBE included 2-methyl-1-propene (2-MP), carbon monoxide, carbon dioxide and water; TBA decomposed to 2-MP and water. Continuous PCO of 4 TBA proceeded faster in humid air than dry air. MTBE oxidation, however, was less sensitive to humidity. The TiO2 catalyst was stable during continuous PCO of MTBE and TBA above 373 K, but gradually lost activity below 373 K; the catalyst could be regenerated by UV irradiation in the absence of gas-phase VOCs. Sulphur dioxide, carbon monoxide, carbon dioxide and water were identified as ultimate products of PCO of ethanethiol. Acetic acid was identified as a photocatalytic oxidation by-product. The limits of ethanethiol concentration and temperature, at which the reactor performance was stable for indefinite time, were established. The apparent reaction kinetics appeared to be independent of the reaction temperature within the studied limits, 373 to 453 K. The catalyst was completely and irreversibly deactivated with ethanethiol TCO. Volatile PCO products of MA included ammonia, nitrogen dioxide, nitrous oxide, carbon dioxide and water. Formamide was observed among DMA PCO products together with others similar to the ones of MA. TCO for both substances resulted in the formation of ammonia, hydrogen cyanide, carbon monoxide, carbon dioxide and water. No deactivation of the photocatalyst during the multiple long-run experiments was observed at the concentrations and temperatures used in the study. PCO of MA was also studied in the aqueous phase. Maximum efficiency was achieved in an alkaline media, where MA exhibited high fugitivity. Two mechanisms of aqueous PCO – decomposition to formate and ammonia, and oxidation of organic nitrogen directly to nitrite - lead ultimately to carbon dioxide, water, ammonia and nitrate: formate and nitrite were observed as intermediates. A part of the ammonia formed in the reaction was oxidized to nitrite and nitrate. This finding helped in better understanding of the gasphase PCO pathways. The PCO kinetic data for VOCs fitted well to the monomolecular Langmuir- Hinshelwood (L-H) model, whereas TCO kinetic behaviour matched the first order process for volatile amines and the L-H model for others. It should be noted that both LH and the first order equations were only the data fit, not the real description of the reaction kinetics. The dependence of the kinetic constants on temperature was established in the form of an Arrhenius equation.

Determination of compression behaviour of coating layer

The strength properties of paper coating layer are very important in converting and printing operations. Too great or low strength of the coating can affect several problems in printing. One of the problems caused by the strength of coating is the cracking at the fold. After printing the paper is folded to final form and the pages are stapled together. In folding the paper coating can crack causing aesthetic damage over printed image or in the worst case the centre sheet can fall off in stapling. When folding the paper other side undergoes tensile stresses and the other side compressive stresses. If the difference between these stresses is too high, the coating can crack on the folding. To better predict and prevent cracking at the fold it is good to know the strength properties of coating layer. It has measured earlier the tensile strength of coating layer but not the compressive strength. In this study it was tried to find some way to measure the compressive strength of the coating layer and investigate how different coatings behave in compression. It was used the short span crush test, which is used to measure the in-plane compressive strength of paperboards, to measure the compressive strength of the coating layer. In this method the free span of the specimen is very small which prevent buckling. It was measured the compressive strength of free coating films as well as coated paper. It was also measured the tensile strength and the Bendtsen air permeance of the coating film. The results showed that the shape of pigment has a great effect to the strength of coating. Platy pigment gave much better strength than round or needle-like pigment. On the other hand calcined kaolin, which is also platy but the particles are aggregated, decreased the strength substantially. The difference in the strength can be explained with packing of the particles which is affecting to the porosity and thus to the strength. The platy kaolin packs up much better than others and creates less porous structure. The results also showed that the binder properties have a great effect to the compressive strength of coating layer. The amount of latex and the glass transition temperature, Tg, affect to the strength. As the amount of latex is increasing, the strength of coating is increasing also. Larger amount of latex is binding the pigment particles better together and decreasing the porosity. Compressive strength was increasing when the Tg was increasing because the hard latex gives a stiffer and less elastic film than soft latex.