On the Condition Monitoring of Induction machines

The research of condition monitoring of electric motors has been wide for several decades. The research and development at universities and in industry has provided means for the predictive condition monitoring. Many different devices and systems are developed and are widely used in industry, transportation and in civil engineering. In addition, many methods are developed and reported in scientific arenas in order to improve existing methods for the automatic analysis of faults. The methods, however, are not widely used as a part of condition monitoring systems. The main reasons are, firstly, that many methods are presented in scientific papers but their performance in different conditions is not evaluated, secondly, the methods include parameters that are so case specific that the implementation of a systemusing such methods would be far from straightforward. In this thesis, some of these methods are evaluated theoretically and tested with simulations and with a drive in a laboratory. A new automatic analysis method for the bearing fault detection is introduced. In the first part of this work the generation of the bearing fault originating signal is explained and its influence into the stator current is concerned with qualitative and quantitative estimation. The verification of the feasibility of the stator current measurement as a bearing fault indicatoris experimentally tested with the running 15 kW induction motor. The second part of this work concentrates on the bearing fault analysis using the vibration measurement signal. The performance of the micromachined silicon accelerometer chip in conjunction with the envelope spectrum analysis of the cyclic bearing faultis experimentally tested. Furthermore, different methods for the creation of feature extractors for the bearing fault classification are researched and an automatic fault classifier using multivariate statistical discrimination and fuzzy logic is introduced. It is often important that the on-line condition monitoring system is integrated with the industrial communications infrastructure. Two types of a sensor solutions are tested in the thesis: the first one is a sensor withcalculation capacity for example for the production of the envelope spectra; the other one can collect the measurement data in memory and another device can read the data via field bus. The data communications requirements highly depend onthe type of the sensor solution selected. If the data is already analysed in the sensor the data communications are needed only for the results but in the other case, all measurement data need to be transferred. The complexity of the classification method can be great if the data is analysed at the management level computer, but if the analysis is made in sensor itself, the analyses must be simple due to the restricted calculation and memory capacity.

Assessing Strategic IT Investments of Forest Industry by Means of the Real Options Approach, Case: Stora Enso

Tutkimuksen päämääränä oli tutkia miten reaalioptiomenetelmä soveltuu metsäteollisuuden strategisten informaatioteknologiainvestointien arvioimiseen. Tässä tutkimuksessa muodostettiin mukautettu reaalioptiosovelluskehys, esiteltyjen reaalioptiosovelluskehyksien perusteella. Valitut investointiehdotukset arvioitiin muodostetun sovelluskehyksen avulla. Tutkimus oli luonteeltaan kvalitatiivinen. Pääasiallisia tiedonlähteitä olivat lehtiartikkelit, GDSS -istunnot ja haastattelut. Tutkimuksen tuloksena selvisi, että reaalioptiomenetelmä sopii metsäteollisuudenstrategisten informaatioteknologiainvestointien arvioimiseen. On kuitenkin huomioitava, että investoinnin suunnitteluprosessin kypsyysaste vaikuttaa reaalioptiomenetelmän soveltamiseen. Tutkimuksessa arvioidut investoinnit ovat investoinnin suunnitteluvaiheen varhaisessa vaiheessa.

R&D Performance Analysis: Case Studies on the Challenges and Promotion of the Evaluation and Measurement of R&D

Due to the intense international competition, demanding, and sophisticated customers, and diverse transforming technological change, organizations need to renew their products and services by allocating resources on research and development (R&D). Managing R&D is complex, but vital for many organizations to survive in the dynamic, turbulent environment. Thus, the increased interest among decision-makers towards finding the right performance measures for R&D is understandable. The measures or evaluation methods of R&D performance can be utilized for multiple purposes; for strategic control, for justifying the existence of R&D, for providing information and improving activities, as well as for the purposes of motivating and benchmarking. The earlier research in the field of R&D performance analysis has generally focused on either the activities and considerable factors and dimensions - e.g. strategic perspectives, purposes of measurement, levels of analysis, types of R&D or phases of R&D process - prior to the selection of R&Dperformance measures, or on proposed principles or actual implementation of theselection or design processes of R&D performance measures or measurement systems. This study aims at integrating the consideration of essential factors anddimensions of R&D performance analysis to developed selection processes of R&D measures, which have been applied in real-world organizations. The earlier models for corporate performance measurement that can be found in the literature, are to some extent adaptable also to the development of measurement systemsand selecting the measures in R&D activities. However, it is necessary to emphasize the special aspects related to the measurement of R&D performance in a way that make the development of new approaches for especially R&D performance measure selection necessary: First, the special characteristics of R&D - such as the long time lag between the inputs and outcomes, as well as the overall complexity and difficult coordination of activities - influence the R&D performance analysis problems, such as the need for more systematic, objective, balanced and multi-dimensional approaches for R&D measure selection, as well as the incompatibility of R&D measurement systems to other corporate measurement systems and vice versa. Secondly, the above-mentioned characteristics and challenges bring forth the significance of the influencing factors and dimensions that need to be recognized in order to derive the selection criteria for measures and choose the right R&D metrics, which is the most crucial step in the measurement system development process. The main purpose of this study is to support the management and control of the research and development activities of organizations by increasing the understanding of R&D performance analysis, clarifying the main factors related to the selection of R&D measures and by providing novel types of approaches and methods for systematizing the whole strategy- and business-based selection and development process of R&D indicators.The final aim of the research is to support the management in their decision making of R&D with suitable, systematically chosen measures or evaluation methods of R&D performance. Thus, the emphasis in most sub-areas of the present research has been on the promotion of the selection and development process of R&D indicators with the help of the different tools and decision support systems, i.e. the research has normative features through providing guidelines by novel types of approaches. The gathering of data and conducting case studies in metal and electronic industry companies, in the information and communications technology (ICT) sector, and in non-profit organizations helped us to formulate a comprehensive picture of the main challenges of R&D performance analysis in different organizations, which is essential, as recognition of the most importantproblem areas is a very crucial element in the constructive research approach utilized in this study. Multiple practical benefits regarding the defined problemareas could be found in the various constructed approaches presented in this dissertation: 1) the selection of R&D measures became more systematic when compared to the empirical analysis, as it was common that there were no systematic approaches utilized in the studied organizations earlier; 2) the evaluation methods or measures of R&D chosen with the help of the developed approaches can be more directly utilized in the decision-making, because of the thorough consideration of the purpose of measurement, as well as other dimensions of measurement; 3) more balance to the set of R&D measures was desired and gained throughthe holistic approaches to the selection processes; and 4) more objectivity wasgained through organizing the selection processes, as the earlier systems were considered subjective in many organizations. Scientifically, this dissertation aims to make a contribution to the present body of knowledge of R&D performance analysis by facilitating dealing with the versatility and challenges of R&D performance analysis, as well as the factors and dimensions influencing the selection of R&D performance measures, and by integrating these aspects to the developed novel types of approaches, methods and tools in the selection processes of R&D measures, applied in real-world organizations. In the whole research, facilitation of dealing with the versatility and challenges in R&D performance analysis, as well as the factors and dimensions influencing the R&D performance measure selection are strongly integrated with the constructed approaches. Thus, the research meets the above-mentioned purposes and objectives of the dissertation from the scientific as well as from the practical point of view.

The effects of selective estrogen receptor modulators on the death of breast cancer cells and osteoblastic cells

Selektiivisten estrogeenireseptorin muuntelijoiden (serm) vaikutus rintasyöpäsolujen ja luun solujen kuolemaan Selektiiviset estrogeenireseptorin muuntelijat (SERMit) ovat ryhmä kemialliselta rakenteeltaan erilaisia yhdisteitä jotka sitoutuvat solunsisäisiin estrogeenireseptoreihin toimien joko estrogeenin kaltaisina yhdisteinä tai estrogeenin vastavaikuttajina. Tamoksifeeni on SERM –yhdiste, jota on jo pitkään käytetty estrogeenireseptoreita (ER) ilmentävän rintasyövän lääkehoidossa. Tamoksifeeni sekä estää rintasyöpäsolujen jakaantumista että toisaalta aikaansaa niiden apoptoosin eli ohjelmoidun solukuoleman muuntelemalla ER-välitteisesti kohdesolun geenien ilmentymistä. Viimeaikaiset tutkimustulokset ovat kuitenkin osoittaneet tamoksifeenilla olevan myös nopeampia, nongenomisia vaikutusmekanismeja. Tässä väitöskirjatyössä tutkimme niitä nopeita vaikutusmekanismeja joiden avulla tamoksifeeni vaikuttaa rintasyöpäsolujen elinkykyyn. Osoitamme että tamoksifeeni farmakologisina pitoisuuksina aikaansaa nopean mitokondriaalisen solukuolemaan johtavan signallointireitin aktivoitumisen rintasyöpäsoluissa. Tämän lisäksi tutkimme myös tamoksifeenin aiheuttamaan mitokondriovaurioon johtavia tekijöitä. Tutkimustuloksemme osoittavat että ER-positiivisissa rintasyöpäsoluissa tamoksifeeni indusoi pitkäkestoisen ERK-kinaasiaktivaation, joka voidaan estää 17-beta-estradiolilla. Tamoksifeenin aikaansaama nopea solukuolema on pääosin ER:sta riippumaton tapahtuma, mutta siihen voidaan vaikuttaa myös ER-välitteisin mekanismein. Sen sijaan epidermaalisen kasvutekijäreseptorin (EGFR) voitiin osoittaa osallistuvan tamoksifeenin nopeiden vaikutusten välittämiseen. Tämän lisäksi vertailimme myös estradiolin ja eri SERM-yhdisteiden kykyä suojata apoptoosilta käyttämällä osteoblastiperäisiä soluja. Pytyäksemme vertailemaan ER-isotyyppien roolia eri yhdisteiden suojavaikutuksissa, transfektoimme U2OS osteosarkoomasolulinjan ilmentämään pysyvästi joko ERalfaa tai ERbetaa. Tulostemme mukaan sekä estradioli että uusi SERM-yhdiste ospemifeeni suojaavat osteoblastin kaltaisia soluja etoposidi-indusoidulta apoptoosilta. Sekä ERalfa että ERbeta pystyivät välittämään suojavaikutusta, joskin vaikutukset erosivat toisistaan. Lisäksi havaitsimme edellä mainitun suojavaikutuksen olevan yhteydessä muutoksiin solujen sytokiiniekspressiossa. Tietoa SERM-yhdisteiden anti-ja proapoptoottisten vaikutusmekanismeista eri kohdekudoksissa voidaan mahdollisesti hyödyntää kehiteltäessä uusia kudosspesifisiä SERM-yhdisteitä.

On the Application of Beam on Elastic Foundation Theory to the Analysis of Stiffened Plate Strips

The main objective of this thesis is to show that plate strips subjected to transverse line loads can be analysed by using the beam on elastic foundation (BEF) approach. It is shown that the elastic behaviour of both the centre line section of a semi infinite plate supported along two edges, and the free edge of a cantilever plate strip can be accurately predicted by calculations based on the two parameter BEF theory. The transverse bending stiffness of the plate strip forms the foundation. The foundation modulus is shown, mathematically and physically, to be the zero order term of the fourth order differential equation governing the behaviour of BEF, whereas the torsion rigidity of the plate acts like pre tension in the second order term. Direct equivalence is obtained for harmonic line loading by comparing the differential equations of Levy's method (a simply supported plate) with the BEF method. By equating the second and zero order terms of the semi infinite BEF model for each harmonic component, two parameters are obtained for a simply supported plate of width B: the characteristic length, 1/ λ, and the normalized sum, n, being the effect of axial loading and stiffening resulting from the torsion stiffness, nlin. This procedure gives the following result for the first mode when a uniaxial stress field was assumed (ν = 0): 1/λ = √2B/π and nlin = 1. For constant line loading, which is the superimposition of harmonic components, slightly differing foundation parameters are obtained when the maximum deflection and bending moment values of the theoretical plate, with v = 0, and BEF analysis solutions are equated: 1 /λ= 1.47B/π and nlin. = 0.59 for a simply supported plate; and 1/λ = 0.99B/π and nlin = 0.25 for a fixed plate. The BEF parameters of the plate strip with a free edge are determined based solely on finite element analysis (FEA) results: 1/λ = 1.29B/π and nlin. = 0.65, where B is the double width of the cantilever plate strip. The stress biaxial, v > 0, is shown not to affect the values of the BEF parameters significantly the result of the geometric nonlinearity caused by in plane, axial and biaxial loading is studied theoretically by comparing the differential equations of Levy's method with the BEF approach. The BEF model is generalised to take into account the elastic rotation stiffness of the longitudinal edges. Finally, formulae are presented that take into account the effect of Poisson's ratio, and geometric non linearity, on bending behaviour resulting from axial and transverse inplane loading. It is also shown that the BEF parameters of the semi infinite model are valid for linear elastic analysis of a plate strip of finite length. The BEF model was verified by applying it to the analysis of bending stresses caused by misalignments in a laboratory test panel. In summary, it can be concluded that the advantages of the BEF theory are that it is a simple tool, and that it is accurate enough for specific stress analysis of semi infinite and finite plate bending problems.

Subjectivity in the valuation : Case study on the Finnish biotechnology industry

The thesis combines valuation and behavioral economics literature, which is not common among the Finnish management accounting research. Furthermore, the valuation is studied in biotechnology context and those type of studies are rather rare as well. The thesis studies the valuation in the Finnish biotechnology industry. The concepts of behavioral finance are employed in the empirical part of the study to explore decision-makers’ behavior in valuation processes. The main interest of this study is to explore how subjectivity of a decision-maker affects the valuation in the biotechnology industry. The valuation is studied from two perspectives. First, what is the best valuation model for biotechnology companies suggested by the valuation literature? Second, how the valuation in biotechnology industry is done in practice and how the decision-makers subjectivity affects the valuation? The literature review aims at seeking the best valuation model. The real options were found to be the most suitable valuation model for biotechnology companies, especially in the early stages of product development. The real option’s ability to take the value of the inherent options into account results in theoretically most correct valuations. The only disadvantage is the model’s complexity when compared to other models, such as discounted cash flow models. The empirical part of the study consists of a case study, which examines the valuation practices of the Finnish biotechnology companies. When it comes to the valuation models used in practice, it was found that the companies were using rather simple valuation models, which was due to two reasons. First, the interviewees did not believe in the valuation models and second, they were familiar neither with the most sophisticated models nor with all the theoretical aspects of the models they were using. The material for the study was collected with theme interviews. Four CEO’s of highly successful Finnish biotechnology companies. Strong signs of the decision-makers’ subjectivity in valuation were observed. Most obvious were the signs of framing. Furthermore, herding, excessive optimism, and overconfidence were present. All the behavioral concepts observed most likely have a severe effect on the valuation. As a result, the valuation can easily become overly optimistic, which leads to overvalued investments and to continuation of already unprofitable projects. Framing had the strongest evidence. If the product being valued is framed successfully, the risk of overvaluation is high, thus a strong belief can justify almost any value.

Corporate Social Responsibility and Shipping Views of Baltic Sea Shipping Companies on the Benefits of Responsibility

The safety of shipping operations in the Baltic Sea is an extensively studied issue due to the density of traffic and the ecological sensitivity of the area. The focus has, however, mainly been on ship technology or on traffic control measures and the operative safety aspect of shipping is in a minor position in maritime safety studies and is lacking in terms of solutions. Self-regulatory and voluntary measures could be effective ways to improve the operational safety of shipping. Corporate social responsibility, or CSR, is one example of a voluntary measure that the shipping companies can take. CSR can enhance maritime safety and improve the shipping companies’ competitiveness. The aim of this study is to increase the knowledge of CSR in the maritime sector and study its applicability and benefits to the shipping companies. The research comprises of a theory part and a questionnaire study, which examine the significance of corporate social responsibility in shipping companies’ maritime safety and competitiveness. The aim of the questionnaire study is to find out how corporate social responsibility is implemented in the shipping companies. According to the literature review, responsible actions can produce financial and time costs, but due to these actions cost savings in the form of learning and increased efficiency can be achieved. Responsible actions can also produce concrete improvements and a reputation of responsibility that can lead to both cost savings and increase in the company’s income. CSR is recognised as having real business benefits in terms of attracting customers and high-quality employees. In shipping, CSR usually focuses on environmental issues. Environmental social responsibility in shipping is mainly motivated by the need to comply with existing and forthcoming regulation. Shipping companies engage in CSR to gain competitive advantage and to increase maritime safety. The social aspects of CSR take into account the well-being and skills of the employees, corporation and other stakeholders of the company. The questionnaire study revealed that the most common CSR measures in shipping companies are environmental measures, and that environmental concerns are considered to be the most important reason to engage in CSR. From the preliminary question about the concept of CSR it can also be seen that safety issues are commonly considered to be a part of CSR and safety gains are the second most important reason to engage in CSR. From the questionnaire, it can also be extrapolated that gaining a better reputation is one of the most important reasons to engage in CSR in the first place. For example, the main economic benefit was seen to be the increase of customer numbers as a result of a better reputation. Based on the study, it would seem that companies are starting to realise that they might gain competitive advantage and be favoured as shippers if they engage in sustainable, responsible operations and present themselves as “green”.

Empirical study on the adoption, use and effects of cloud-based testing

Cloud computing is a practically relevant paradigm in computing today. Testing is one of the distinct areas where cloud computing can be applied. This study addressed the applicability of cloud computing for testing within organizational and strategic contexts. The study focused on issues related to the adoption, use and effects of cloudbased testing. The study applied empirical research methods. The data was collected through interviews with practitioners from 30 organizations and was analysed using the grounded theory method. The research process consisted of four phases. The first phase studied the definitions and perceptions related to cloud-based testing. The second phase observed cloud-based testing in real-life practice. The third phase analysed quality in the context of cloud application development. The fourth phase studied the applicability of cloud computing in the gaming industry. The results showed that cloud computing is relevant and applicable for testing and application development, as well as other areas, e.g., game development. The research identified the benefits, challenges, requirements and effects of cloud-based testing; and formulated a roadmap and strategy for adopting cloud-based testing. The study also explored quality issues in cloud application development. As a special case, the research included a study on applicability of cloud computing in game development. The results can be used by companies to enhance the processes for managing cloudbased testing, evaluating practical cloud-based testing work and assessing the appropriateness of cloud-based testing for specific testing needs.

Defining the keyhole modes – the effects on the weld geometry and the molten pool behaviour in high power laser welding of stainless steels

Keyhole welding, meaning that the laser beam forms a vapour cavity inside the steel, is one of the two types of laser welding processes and currently it is used in few industrial applications. Modern high power solid state lasers are becoming more used generally, but not all process fundamentals and phenomena of the process are well known and understanding of these helps to improve quality of final products. This study concentrates on the process fundamentals and the behaviour of the keyhole welding process by the means of real time high speed x-ray videography. One of the problem areas in laser welding has been mixing of the filler wire into the weld; the phenomena are explained and also one possible solution for this problem is presented in this study. The argument of this thesis is that the keyhole laser welding process has three keyhole modes that behave differently. These modes are trap, cylinder and kaleidoscope. Two of these have sub-modes, in which the keyhole behaves similarly but the molten pool changes behaviour and geometry of the resulting weld is different. X-ray videography was used to visualize the actual keyhole side view profile during the welding process. Several methods were applied to analyse and compile high speed x-ray video data to achieve a clearer image of the keyhole side view. Averaging was used to measure the keyhole side view outline, which was used to reconstruct a 3D-model of the actual keyhole. This 3D-model was taken as basis for calculation of the vapour volume inside of the keyhole for each laser parameter combination and joint geometry. Four different joint geometries were tested, partial penetration bead on plate and I-butt joint and full penetration bead on plate and I-butt joint. The comparison was performed with selected pairs and also compared all combinations together.