Maritime Safety in the Gulf of Finland. Review on Policy Instruments

Suomenlahden lisääntynyt meriliikenne on herättänyt huolta meriliikenteen turvallisuuden tasosta, ja erityisesti Venäjän öljyviennin kasvu on lisännyt öljyonnettomuuden todennäköisyyttä Suomenlahdella. Erilaiset kansainväliset, alueelliset ja kansalliset ohjauskeinot pyrkivät vähentämään merionnettomuuden riskiä ja meriliikenteen muita haittavaikutuksia. Tämä raportti käsittelee meriturvallisuuden yhteiskunnallisia ohjauskeinoja: ohjauskeinoja yleisellä tasolla, meriturvallisuuden keskeisimpiä säätelijöitä, meriturvallisuuden ohjauskeinoja ja meriturvallisuuspolitiikan tulevaisuuden näkymiä, ohjauskeinojen tehokkuutta ja nykyisen meriturvallisuuden ohjausjärjestelmän heikkouksia. Raportti on kirjallisuuskatsaus meriturvallisuuden yhteiskunnalliseen sääntelyn rakenteeseen ja tilaan erityisesti Suomenlahden meriliikenteen näkökulmasta. Raportti on osa tutkimusprojektia ”SAFGOF - Suomenlahden meriliikenteen kasvunäkymät 2007 - 2015 ja kasvun vaikutukset ympäristölle ja kuljetusketjujen toimintaan” ja sen työpakettia 6 ”Keskeisimmät riskit ja yhteiskunnalliset vaikutuskeinot”. Yhteiskunnalliset ohjauskeinot voidaan ryhmitellä hallinnollisiin, taloudellisiin ja tietoohjaukseen perustuviin ohjauskeinoihin. Meriturvallisuuden edistämisessä käytetään kaikkia näitä, mutta hallinnolliset ohjauskeinot ovat tärkeimmässä asemassa. Merenkulun kansainvälisen luonteen vuoksi meriturvallisuuden sääntely tapahtuu pääosin kansainvälisellä tasolla YK:n ja erityisesti Kansainvälisen merenkulkujärjestön (IMO) toimesta. Lisäksi myös Euroopan Unionilla on omaa meriturvallisuuteen liittyvää sääntelyä ja on myös olemassa muita alueellisia meriturvallisuuden edistämiseen liittyviä elimiä kuten HELCOM. Joitakin meriturvallisuuden osa-alueita säädellään myös kansallisella tasolla. Hallinnolliset meriturvallisuuden ohjauskeinot sisältävät aluksen rakenteisiin ja varustukseen, alusten kunnon valvontaan, merimiehiin ja merityön tekemiseen sekä navigointiin liittyviä ohjauskeinoja. Taloudellisiin ohjauskeinoihin kuuluvat esimerkiksi väylä- ja satamamaksut, merivakuutukset, P&I klubit, vastuullisuus- ja korvauskysymykset sekä taloudelliset kannustimet. Taloudellisten ohjauskeinojen käyttö meriturvallisuuden edistämiseen on melko vähäistä verrattuna hallinnollisten ohjauskeinojen käyttöön, mutta niitä voitaisiin varmasti käyttää enemmänkin. Ongelmana taloudellisten ohjauskeinojen käytössä on se, että ne kuuluvat pitkälti kansallisen sääntelyn piiriin, joten alueellisten tai kansainvälisten intressien edistäminen taloudellisilla ohjauskeinoilla voi olla hankalaa. Tieto-ohjaus perustuu toimijoiden vapaaehtoisuuteen ja yleisen tiedotuksen lisäksi tieto-ohjaukseen sisältyy esimerkiksi vapaaehtoinen koulutus, sertifiointi tai meriturvallisuuden edistämiseen tähtäävät palkinnot. Poliittisella tasolla meriliikenteen aiheuttamat turvallisuusriskit Suomenlahdella on otettu vakavasti ja paljon työtä tehdään eri tahoilla riskien minimoimiseksi. Uutta sääntelyä on odotettavissa etenkin liittyen meriliikenteen ympäristövaikutuksiin ja meriliikenteen ohjaukseen kuten meriliikenteen sähköisiin seurantajärjestelmiin. Myös inhimilliseen tekijän merkitykseen meriturvallisuuden kehittämisessä on kiinnitetty lisääntyvissä määrin huomiota, mutta inhimilliseen tekijän osalta tehokkaiden ohjauskeinojen kehittäminen näyttää olevan haasteellista. Yleisimmin lääkkeeksi esitetään koulutuksen kehittämistä. Kirjallisuudessa esitettyjen kriteereiden mukaan tehokkaiden ohjauskeinojen tulisi täyttää seuraavat vaatimukset: 1) tarkoituksenmukaisuus – ohjauskeinojen täytyy olla sopivia asetetun tavoitteen saavuttamiseen, 2) taloudellinen tehokkuus – ohjauskeinon hyödyt vs. kustannukset tulisi olla tasapainossa, 3) hyväksyttävyys – ohjauskeinon täytyy olla hyväksyttävä asianosaisten ja myös laajemman yhteiskunnan näkökulmasta katsottuna, 4) toimeenpano – ohjauskeinon toimeenpanon pitää olla mahdollista ja sen noudattamista täytyy pystyä valvomaan, 5) lateraaliset vaikutukset – hyvällä ohjauskeinolla on positiivisia seurannaisvaikutuksia muutoinkin kuin vain ohjauskeinon ensisijaisten tavoitteiden saavuttaminen, 6) kannustin ja uuden luominen – hyvä ohjauskeino kannustaa kokeilemaan uusia ratkaisuja ja kehittämään toimintaa. Meriturvallisuutta koskevaa sääntelyä on paljon ja yleisesti ottaen merionnettomuuksien lukumäärä on ollut laskeva viime vuosikymmenien aikana. Suuri osa sääntelystä on ollut tehokasta ja parantanut turvallisuuden tasoa maailman merillä. Silti merionnettomuuksia ja muita vaarallisia tapahtumia sattuu edelleen. Nykyistä sääntelyjärjestelmää voidaan kritisoida monen asian suhteen. Kansainvälisen sääntelyn aikaansaaminen ei ole helppoa: prosessi on yleensä hidas ja tuloksena voi olla kompromissien kompromissi. Kansainvälinen sääntely on yleensä reaktiivista eli ongelmakohtiin puututaan vasta kun jokin onnettomuus tapahtuu sen sijaan että se olisi proaktiivista ja pyrkisi puuttumaan ongelmakohtiin jo ennen kuin jotain tapahtuu. IMO:n työskentely perustuu kansallisvaltioiden osallistumiseen ja sääntelyn toimeenpano tapahtuu lippuvaltioiden toimesta. Kansallisvaltiot ajavat IMO:ssa pääasiallisesti omia intressejään ja sääntelyn toimeenpanossa on suuria eroja lippuvaltioiden välillä. IMO:n kyvyttömyys puuttua havaittuihin ongelmiin nopeasti ja ottaa sääntelyssä huomioon paikallisia olosuhteita on johtanut siihen, että esimerkiksi Euroopan Unioni on alkanut itse säädellä meriturvallisuutta ja että on olemassa sellaisia alueellisia erityisjärjestelyjä kuin PSSA (particularly sensitive sea area – erityisen herkkä merialue). Merenkulkualalla toimii monenlaisia yrityksiä: toisaalta yrityksiä, jotka pyrkivät toimimaan turvallisesti ja kehittämään turvallisuutta vielä korkeammalle tasolle, ja toisaalta yrityksiä, jotka toimivat niin halvalla kuin mahdollista, eivät välitä turvallisuusseikoista, ja joilla usein on monimutkaiset ja epämääräiset omistusolosuhteet ja joita vahingon sattuessa on vaikea saada vastuuseen. Ongelma on, että kansainvälisellä merenkulkualalla kaikkien yritysten on toimittava samoilla markkinoilla. Vastuuttomien yritysten toiminnan mahdollistavat laivaajat ja muut alan toimijat, jotka suostuvat tekemään yhteistyötä niiden kanssa. Välinpitämätön suhtautuminen turvallisuuteen johtuu osaksi myös merenkulun vanhoillisesta turvallisuuskulttuurista. Verrattaessa meriturvallisuuden sääntelyjärjestelmää kokonaisuutena tehokkaiden ohjauskeinoihin kriteereihin, voidaan todeta, että monien kriteerien osalta nykyistä järjestelmää voidaan pitää tehokkaana ja onnistuneena. Suurimmat ongelmat lienevät sääntelyn toimeenpanossa ja ohjauskeinojen kustannustehokkuudessa. Lippuvaltioiden toimeenpanoon perustuva järjestelmä ei toimi toivotulla tavalla, josta mukavuuslippujen olemassa olo on selvin merkki. Ohjauskeinojen, sekä yksittäisten ohjauskeinojen että vertailtaessa eri ohjauskeinoja keskenään, kustannustehokkuutta on usein vaikea arvioida, minkä seurauksena ohjauskeinojen kustannustehokkuudesta ei ole saatavissa luotettavaa tietoa ja tuloksena voi olla, että ohjauskeino on käytännössä pienen riskin eliminoimista korkealla kustannuksella. Kansainvälisen tason meriturvallisuus- (ja merenkulku-) politiikan menettelytavoiksi on ehdotettu myös muita vaihtoehtoja kuin nykyinen järjestelmä, esimerkiksi monitasoista tai polysentristä hallintojärjestelmää. Monitasoisella hallintojärjestelmällä tarkoitetaan järjestelmää, jossa keskushallinto on hajautettu sekä vertikaalisesti alueellisille tasoille että horisontaalisesti ei-valtiollisille toimijoille. Polysentrinen hallintojärjestelmä menee vielä askeleen pidemmälle. Polysentrinen hallintojärjestelmä on hallintotapa, jonka puitteissa kaikentyyppiset toimijat, sekä yksityiset että julkiset, voivat osallistua hallintoon, siis esimerkiksi hallitukset, edunvalvontajärjestöt, kaupalliset yritykset jne. Kansainvälinen lainsäädäntö määrittelee yleiset tasot, mutta konkreettiset toimenpiteet voidaan päättää paikallisella tasolla eri toimijoiden välisessä yhteistyössä. Tämän tyyppisissä hallintojärjestelmissä merenkulkualan todellinen, kansainvälinen mutta toisaalta paikallinen, toimintaympäristö tulisi otetuksi paremmin huomioon kuin järjestelmässä, joka perustuu kansallisvaltioiden keskenään yhteistyössä tekemään sääntelyyn. Tällainen muutos meriturvallisuuden hallinnassa vaatisi kuitenkin suurta periaatteellista suunnanmuutosta, jollaisen toteutumista ei voi pitää kovin todennäköisenä ainakaan lyhyellä tähtäimellä.

Situational awareness concept in a multinational collaboration environment : challenges in the information sharing framework

Technological capabilities are built to support different types of collaboration, and this gives the justification to widely observe, how activity environments are influenced by technology. Technology as an enabler can be addressed from different perspectives, other than merely technological. Dynamic, evolving environment is at the same time interesting but also challenging. As a multinational collaboration environment, the maritime surveillance is an good example of time critical and evolving environment, where technological solutions enable new ways of collaboration. Justification for the inspiration to use maritime environment as the baseline for understanding the challenges in creating and maintaining adequate level of situational awareness, derives from the complexity of the collaboration and information sharing environment elements, needed to be taken into account, when analyzing criticalities related to decision making. Situational awareness is an important element supporting decision making, and challenges related to it can also be observed in the maritime environment. This dissertation describes the structures and factors involved in this complex setting, found from the case studies that should be taken into account when trying to understand, how these elements affect the activities. This dissertation focuses on the gray area that is between a life threatening situation and normal everyday activities. From the multinational experimentation series case studies, MNE5 and MNE6 it was possible to observe situations that were not life threatening for the participants themselves, but not also basic every day activities. These case studies provided a unique possibility to see situations, where gaining of situational awareness and decision making are challenged with time critical crisis situations. Unfortunately organizations do not normally take the benefit from the everyday work to prepare themselves for possible emerging crisis situations. This dissertation focuses on creating a conceptual model and a concept that supports organizations – also outside the maritime community – to improve their ability to support gaining of situational awareness from the individual training level, all the way to changes in organizational structures in aiming for better support for decision making from the individual level to the highest decision making level. Quick changes and unpredictability are reality in organizations and organizations do not have the possibility to control all the factors that affect their functioning. Since we cannot be prepared for everything, and predict every crisis, individual activities inside teams and as a part of organizations, need to be supported with guidance, tools and training in order to support acting in challenging situations. In fact the ideology of the conceptual model created, lies especially in the aim of not controlling everything in beforehand, but supporting organizations with concrete procedures to help individuals to react in different, unpredictable situations, instead of focusing on traditional risk prevention and management. Technological capabilities are not automatically solutions for functional challenges; this is why it is justified to broaden the problem area observation from the technological perspective. This dissertation demonstrates that it is possible to support collaboration in a multinational environment with technological solutions, but it requires the recognition of technological limitations and accepting the possible restrictions related to technological innovations. Technology should not be considered value per se, the value of technology should be defined according to the support of activities, including strategic and operational environment evaluation, identification of organizational elements, and taking into account also the social factors and their challenges. Then we are one step closer to providing technological solutions that support the actual activities by taking into account the variables of the activity environment in question. The multidisciplinary view to approach the information sharing and collaboration framework, is derived especially from the complexity of decision making and building of situational awareness, since they are not build or created in vacuity, but in the organizational framework by the people doing it with the technological capabilities, enabled by the organizational structures. Introduced case studies were related to maritime environment, but according to the research results, it is valid to argue, that based on the lessons learned it is possible to create and further develop conceptual model and to create a general concept to support a wider range of organizations in their attempt to gain better level of situational awareness (SA) and to support decision making. To proof the versatile usage of the developed concept, I have introduced the case study findings to the health care environment and reflected the identified elements from the trauma center to the created concept. The main contribution to complete this adventure is the presented situational awareness concept created in the respect to NATO concept structure. This has been done to tackle the challenge of collaboration by focusing on situational awareness in the information sharing context by providing a theoretical ground and understanding, of how these issues should be approached, and how these elements can be generalized and used to support activities in other environments as well. This dissertation research has been a several year evolving process reflecting and affecting presented case studies and this learning experience from the case studies has also affected the goals and research questions of this dissertation. This venture has been written from a retro perspective according to ideology of process modeling and design rationale to present to the reader how this entire journey took place and what where the critical milestones that affected the end result, conceptual model. Support in a challenging information sharing framework can be provided with the right type of combination of tools, procedures and individual effort. This dissertation will provide insights to those with a new approach to war technology for the organizations to gain a better level of awareness and to improve the capabilities in decision making. This dissertation will present, from the war technology starting point, a new approach and possibility for the organizations to create a better level of awareness and support for decision making with the right combination of tools, procedures and individual effort.

Creative brand launch in phamaceutical over-the-counter markets – case Burana

The purpose of this study is to examine how a launch of a pharmaceutical over-the-counter sold (OTC) brand can be done by using creative solutions and thus affecting the product life cycle. The study is inspired by a phenomenon called Burana. The Burana brand has been a market leader of OTC painkillers in Finland for the past 27 years. The aim of this study is to “solve the mystery” behind Burana brand’s success by focusing on the launch phase of Burana as an OTC medicine. Farmos Group Ltd (the owner of the brand in 1980´s) had not originally invented the product in question – ibuprofen – and the product had already reached it´s maturity phase, if not even decline from the product life cycle aspect when this phenomenon takes place. This has made the marketing choices, the product launch phase as well as the product management even more interesting from the company point of view as well as from a learning point of view. The methodology in this study is qualitative with a descriptive research strategy, while the study is conducted as a longitudinal single-case study. The methods used in this study have been collecting, analyzing and interpreting the data, which is based on the interviewees’ comments and observed behavior. According to the study, the successful launch phase helped in setting the product one step ahead of the competitors and thus aided the brand leadership and prolonged the product life cycle. Another notable aspect that became clear from the interviews and the documentary of Burana´s launch phase was the innovative idea of involving the people of the distribution chain into the product launch through education. As this study has pointed out, it is not enough to for a company to build an innovative team of employees, but also to offer them an involved and encouraging management. According to the interviews, the support from the company management gave the marketing team the encouragement to be innovative. It can be thus stated that the management of a company has an essential role in fostering the creativity within the company.

Improving the competitiveness of electrolytic Zinc process by chemical reaction engineering approach

This doctoral thesis describes the development work performed on the leachand purification sections in the electrolytic zinc plant in Kokkola to increase the efficiency in these two stages, and thus the competitiveness of the plant. Since metallic zinc is a typical bulk product, the improvement of the competitiveness of a plant was mostly an issue of decreasing unit costs. The problems in the leaching were low recovery of valuable metals from raw materials, and that the available technology offered complicated and expensive processes to overcome this problem. In the purification, the main problem was consumption of zinc powder - up to four to six times the stoichiometric demand. This reduced the capacity of the plant as this zinc is re-circulated through the electrolysis, which is the absolute bottleneck in a zinc plant. Low selectivity gave low-grade and low-value precipitates for further processing to metallic copper, cadmium, cobalt and nickel. Knowledge of the underlying chemistry was poor and process interruptions causing losses of zinc production were frequent. Studies on leaching comprised the kinetics of ferrite leaching and jarosite precipitation, as well as the stability of jarosite in acidic plant solutions. A breakthrough came with the finding that jarosite could precipitate under conditions where ferrite would leach satisfactorily. Based on this discovery, a one-step process for the treatment of ferrite was developed. In the plant, the new process almost doubled the recovery of zinc from ferrite in the same equipment as the two-step jarosite process was operated in at that time. In a later expansion of the plant, investment savings were substantial compared to other technologies available. In the solution purification, the key finding was that Co, Ni, and Cu formed specific arsenides in the “hot arsenic zinc dust” step. This was utilized for the development of a three-step purification stage based on fluidized bed technology in all three steps, i.e. removal of Cu, Co and Cd. Both precipitation rates and selectivity increased, which strongly decreased the zinc powder consumption through a substantially suppressed hydrogen gas evolution. Better selectivity improved the value of the precipitates: cadmium, which caused environmental problems in the copper smelter, was reduced from 1-3% reported normally down to 0.05 %, and a cobalt cake with 15 % Co was easily produced in laboratory experiments in the cobalt removal. The zinc powder consumption in the plant for a solution containing Cu, Co, Ni and Cd (1000, 25, 30 and 350 mg/l, respectively), was around 1.8 g/l; i.e. only 1.4 times the stoichiometric demand – or, about 60% saving in powder consumption. Two processes for direct leaching of the concentrate under atmospheric conditions were developed, one of which was implemented in the Kokkola zinc plant. Compared to the existing pressure leach technology, savings were obtained mostly in investment. The scientific basis for the most important processes and process improvements is given in the doctoral thesis. This includes mathematical modeling and thermodynamic evaluation of experimental results and hypotheses developed. Five of the processes developed in this research and development program were implemented in the plant and are still operated. Even though these processes were developed with the focus on the plant in Kokkola, they can also be implemented at low cost in most of the zinc plants globally, and have thus a great significance in the development of the electrolytic zinc process in general.

Transformation of carbon dioxide to diethyl carbonate over ceria and ceria-supported catalysts

Carbon dioxide is regarded, nowadays, as a primary anthropogenic greenhouse gas leading to global warming. Hence, chemical fixation of CO2 has attracted much attention as a possible way to manufacture useful chemicals. One of the most interesting approaches of CO2 transformations is the synthesis of organic carbonates. Since conventional production technologies of these compounds involve poisonous phosgene and carbon monoxide, there is a need to develop novel synthetic methods that would better match the principles of "Green Chemistry" towards protection of the environment and human health. Over the years, synthesis of dimethyl carbonate was under intensive investigation in the academia and industry. Therefore, this study was entirely directed towards equally important homologue of carbonic esters family namely diethyl carbonate (DEC). Novel synthesis method of DEC starting from ethanol and CO2 over heterogeneous catalysts based on ceria (CeO2) was studied in the batch reactor. However, the plausible drawback of the reaction is thermodynamic limitations. The calculated values revealed that the reaction is exothermic (ΔrHØ298K = ─ 16.6 J/ ) and does not occur spontaneously at rooms temperature (ΔrGØ 298K = 35.85 kJ/mol). Moreover, co-produced water easily shifts the reaction equilibrium towards reactants excluding achievement of high yields of the carbonate. Therefore, in-situ dehydration has been applied using butylene oxide as a chemical water trap. A 9-fold enhancement in the amount of DEC was observed upon introduction of butylene oxide to the reaction media in comparison to the synthetic method without any water removal. This result confirms that reaction equilibrium was shifted in favour of the desired product and thermodynamic boundaries of the reaction were suppressed by using butylene oxide as a water scavenger. In order to obtain insight into the reaction network, the kinetic experiments were performed over commercial cerium oxide. On the basis of the selectivity/conversion profile it could be concluded that the one-pot synthesis of diethyl carbonate from ethanol, CO2 and butylene oxide occurs via a consecutive route involving cyclic carbonate as an intermediate. Since commercial cerium oxide suffers from the deactivation problems already after first reaction cycle, in-house CeO2 was prepared applying room temperature precipitation technique. Variation of the synthesis parameters such as synthesis time, calcination temperature and pH of the reaction solution turned to have considerable influence on the physico-chemical and catalytic properties of CeO2. The increase of the synthesis time resulted in high specific surface area of cerium oxide and catalyst prepared within 50 h exhibited the highest amount of basic sites on its surface. Furthermore, synthesis under pH 11 yielded cerium oxide with the highest specific surface area, 139 m2/g, among all prepared catalysts. Moreover, CeO2─pH11 catalyst demonstrated the best catalytic activity and 2 mmol of DEC was produced at 180 oC and 9 MPa of the final reaction pressure. In addition, ceria-supported onto high specific surface area silicas MCM-41, SBA-15 and silica gel were synthesized and tested for the first time as catalysts in the synthesis of DEC. Deposition of cerium oxide on MCM-41 and SiO2 supports resulted in a substantial increase of the alkalinity of the carrier materials. Hexagonal SBA-15 modified with 20 wt % of ceria exhibited the second highest basicity in the series of supported catalysts. Evaluation of the catalytic activity of ceria-supported catalysts showed that reaction carried out over 20 wt % CeO2-SBA-15 generated the highest amount of DEC.

Consumer-led new product development. Case: Dairy Industry

This thesis focuses on consolidation the recommendations on the integration of consumer in new product development (NPD) given in the academic literature, and on the example of the three NPD projects in the case company. The empirical findings advocate that the case company fulfills the principles of consumer-led NPD, and it is only one-step away of the full consumer empowerment strategy. Therefore, its NPD can be seen as an example of consumer-led NPD implementation. The findings also suggest that the product can be developed in consumer-led way regardless of the source of an idea (product- or need-driven), the target audience and resources assigned, in case when consumer mindset is integrated on all levels of organisation: strategic, cultural, operational and process. It is possible with top-management commitment, internal consumer research group, and the sophisticated consumer research methods. The specific managerial recommendations are given on developing consumer-led culture, strategy, NPD process and the appropriate consumer research methods and techniques.

Studies on chemoenzymatic synthesis: Lipase-catalyzed acylation in multistep organic synthesis

In this thesis, biocatalysis is defined as the science of using enzymes as catalysts in organic synthesis. Environmental aspects and the continuously expanding repertoire of available enzymes have firmly established biocatalysis as a prominent means of chemo-, regio- and stereoselective synthesis. Yet, no single methodology can solve all the challenges faced by a synthetic chemist. Therefore, the knowledge and the skills to combine different synthetic methods are relevant. Lipases are highly useful enzymes in organic synthesis. In this thesis, an effort is being made to form a coherent picture of when and how can lipases be incorporated into nonenzymatic synthesis. This is attempted both in the literature review and in the discussion of the results presented in the original publications contained in the thesis. In addition to lipases, oxynitrilases were also used in the work. The experimental part of the thesis comprises of the results reported in four peer-reviewed publications and one manuscript. Selected amines, amino acids and sugar-derived cyanohydrins or their acylated derivatives were each prepared in enantio- or diastereomerically enriched form. Where applicable, attempts were made to combine the enzymatic reactions to other synthetic steps either by the application of completely separate sequential reactions with isolated intermediates (kinetic and functional kinetic resolution of amines), simultaneously occurring reactions without intermediate isolation (dynamic kinetic resolution of amino acid esters) or sequential reactions but without isolating the intermediates (hydrocyanation of sugar aldehydes with subsequent diastereoresolution). In all cases, lipase-catalyzed acylation was the key step by which stereoselectivity was achieved. Lipase from Burkholderia cepacia was a highly selective enzyme with each substrate category, but careful selection of the acyl donor and the solvent was important as well.

Hydrothermal carbonization in the synthesis of sustainable porous carbon materials

Carbon materials are found versatile and applicable in wide range of applications. During the recent years research of carbon materials has focussed on the search of environmentally friendly, sustainable, renewable and low-cost starting material sources as well as simple cost-efficient synthesis techniques. As an alternative synthesis technique in the production of carbon materials hydrothermal carbonization (HTC) has shown a great potential. Depending on the application HTC can be performed as such or as a pretreatment technique. This technique allows synthesis of carbon materials i.e. hydrochars in closed vessel in the presence of water and self-generated pressure at relatively low temperatures (180-250 ˚C). As in many applications well developed porosity and heteroatom distribution are in a key role. Therefore in this study different techniques e.g. varying feedstock, templating and post-treatment in order to introduce these properties to the hydrochars structure were performed. Simple monosaccharides i.e. fructose or glucose and more complex compounds such as cellulose and sludge were performed as starting materials. Addition of secondary precursor e.g. thiophenecarboxaldehyde and ovalbumin was successfully exploited in order to alter heteroatom content. It was shown that well-developed porosity (SBET 550 m2/g) can be achieved via one-pot approach (i.e. exploitation of salt mixture) without conventionally used post-carbonization step. Nitrogen-enriched hydrochars indicated significant Pb(II) and Cr(VI) removal efficiency of 240 mg/g and 68 mg/g respectively. Sulphur addition into carbon network was not found to have enhancing effect on the adsorption of methylene blue or change acidity of the carbon material. However, these hydrochars were found to remove 99.9 % methylene blue and adsorption efficiency of these hydrochars remained over 90 % even after regeneration. In addition to water treatment application N-rich high temperature treated carbon materials were proven applicable as electrocatalyst and electrocatalyst support. Hydrothermal carbonization was shown to be workable technique for the production of carbon materials with variable physico-chemical properties and therefore hydrochars could be applied in several different applications e.g. as alternative low-cost adsorbent for pollutant removal from water.

On Undecidable Dynamical Properties of Reversible One-Dimensional Cellular Automata

Cellular automata are models for massively parallel computation. A cellular automaton consists of cells which are arranged in some kind of regular lattice and a local update rule which updates the state of each cell according to the states of the cell's neighbors on each step of the computation. This work focuses on reversible one-dimensional cellular automata in which the cells are arranged in a two-way in_nite line and the computation is reversible, that is, the previous states of the cells can be derived from the current ones. In this work it is shown that several properties of reversible one-dimensional cellular automata are algorithmically undecidable, that is, there exists no algorithm that would tell whether a given cellular automaton has the property or not. It is shown that the tiling problem of Wang tiles remains undecidable even in some very restricted special cases. It follows that it is undecidable whether some given states will always appear in computations by the given cellular automaton. It also follows that a weaker form of expansivity, which is a concept of dynamical systems, is an undecidable property for reversible one-dimensional cellular automata. It is shown that several properties of dynamical systems are undecidable for reversible one-dimensional cellular automata. It shown that sensitivity to initial conditions and topological mixing are undecidable properties. Furthermore, non-sensitive and mixing cellular automata are recursively inseparable. It follows that also chaotic behavior is an undecidable property for reversible one-dimensional cellular automata.

Synthesis of percarboxylic acids in microreactor

Percarboxylic acids are commonly used as disinfection and bleaching agents in textile, paper, and fine chemical industries. All of these applications are based on the oxidative potential of these compounds. In spite of high interest in these chemicals, they are unstable and explosive chemicals, which increase the risk of synthesis processes and transportation. Therefore, the safety criteria in the production process should be considered. Microreactors represent a technology that efficiently utilizes safety advantages resulting from small scale. Therefore, microreactor technology was used in the synthesis of peracetic acid and performic acid. These percarboxylic acids were produced at different temperatures, residence times and catalyst i.e. sulfuric acid concentrations. Both synthesis reactions seemed to be rather fast because with performic acid equilibrium was reached in 4 min at 313 K and with peracetic acid in 10 min at 343 K. In addition, the experimental results were used to study the kinetics of the formation of performic acid and peracetic acid. The advantages of the microreactors in this study were the efficient temperature control even in very exothermic reaction and good mixing due to the short diffusion distances. Therefore, reaction rates were determined with high accuracy. Three different models were considered in order to estimate the kinetic parameters such as reaction rate constants and activation energies. From these three models, the laminar flow model with radial velocity distribution gave most precise parameters. However, sulfuric acid creates many drawbacks in this synthesis process. Therefore, a ´´greener´´ way to use heterogeneous catalyst in the synthesis of performic acid in microreactor was studied. The cation exchange resin, Dowex 50 Wx8, presented very high activity and a long life time in this reaction. In the presence of this catalyst, the equilibrium was reached in 120 second at 313 K which indicates a rather fast reaction. In addition, the safety advantages of microreactors were investigated in this study. Four different conventional methods were used. Production of peracetic acid was used as a test case, and the safety of one conventional batch process was compared with an on-site continuous microprocess. It was found that the conventional methods for the analysis of process safety might not be reliable and adequate for radically novel technology, such as microreactors. This is understandable because the conventional methods are partly based on experience, which is very limited in connection with totally novel technology. Therefore, one checklist-based method was developed to study the safety of intensified and novel processes at the early stage of process development. The checklist was formulated using the concept of layers of protection for a chemical process. The traditional and three intensified processes of hydrogen peroxide synthesis were selected as test cases. With these real cases, it was shown that several positive and negative effects on safety can be detected in process intensification. The general claim that safety is always improved by process intensification was questioned.

Development of racemization catalysts for dynamic kinetic resolution

Preparation of optically active compounds is of high importance in modern medicinal chemistry. Despite recent advances in the field of asymmetric synthesis, resolution of racemates still remains the most utilized way for preparation of single enantiomers in industrial scale due to its cost-efficiency and simplicity. Enzymatic kinetic resolution (KR) of racemates is a classical method for separation of enantiomers. One of its drawbacks is the limitation of target enantiomer yield to 50%. Dynamic Kinetic Resolution (DKR) allows to reach yields up to 100% by in situ racemization of the less reactive enantiomer. In the first part of this thesis, a number of half-sandwich ruthenium complexes were prepared and evaluated as catalysts for racemization of optically active secondary alcohols. A leading catalyst, Bn5CpRu(CO)2Cl, was identified. The catalyst discovered was extensively characterized by its application for DKR of a broad range of secondary alcohols in a wide range of reaction loadings (1 mmol – 1 mol). Cost-efficient chromatography-free procedure for preparation of this catalyst was developed. Further, detailed kinetic and mechanistic studies of the racemization reactions were performed. Comparison of racemization rates in the presence of Bn5CpRu(CO)2Cl and Ph5CpRu(CO)2Cl catalysts reveals that the performance of the catalytic system can be adjusted by matching of the electronic properties of the catalysts and the substrates. Moreover, dependence of the rate-limiting step from the electronic properties of the reagents was observed. Important conclusions about reaction mechanism were made. Finally, an alternative approach to DKR of amines based on space separated vessels was addressed. This procedure allows the combination of thermolabile enzyme with racemization catalysts active only at high temperatures.

AMB system for high-speed motors using automatic commissioning

The general trend towards increasing e ciency and energy density drives the industry to high-speed technologies. Active Magnetic Bearings (AMBs) are one of the technologies that allow contactless support of a rotating body. Theoretically, there are no limitations on the rotational speed. The absence of friction, low maintenance cost, micrometer precision, and programmable sti ness have made AMBs a viable choice for highdemanding applications. Along with the advances in power electronics, such as signi cantly improved reliability and cost, AMB systems have gained a wide adoption in the industry. The AMB system is a complex, open-loop unstable system with multiple inputs and outputs. For normal operation, such a system requires a feedback control. To meet the high demands for performance and robustness, model-based control techniques should be applied. These techniques require an accurate plant model description and uncertainty estimations. The advanced control methods require more e ort at the commissioning stage. In this work, a methodology is developed for an automatic commissioning of a subcritical, rigid gas blower machine. The commissioning process includes open-loop tuning of separate parts such as sensors and actuators. The next step is to apply a system identi cation procedure to obtain a model for the controller synthesis. Finally, a robust model-based controller is synthesized and experimentally evaluated in the full operating range of the system. The commissioning procedure is developed by applying only the system components available and a priori knowledge without any additional hardware. Thus, the work provides an intelligent system with a self-diagnostics feature and an automatic commissioning.

Synthesis, characterization and chemical sensor application of conducting polymers

Polymeric materials that conduct electricity are highly interesting for fundamental studies and beneficial for modern applications in e.g. solar cells, organic field effect transistors (OFETs) as well as in chemical and bio‐sensing. Therefore, it is important to characterize this class of materials with a wide variety of methods. This work summarizes the use of electrochemistry also in combination with spectroscopic methods in synthesis and characterization of electrically conducting polymers and other π‐conjugated systems. The materials studied in this work are intended for organic electronic devices and chemical sensors. Additionally, an important part of the presented work, concerns rational approaches to the development of water‐based inks containing conducting particles. Electrochemical synthesis and electroactivity of conducting polymers can be greatly enhanced in room temperature ionic liquids (RTILs) in comparison to conventional electrolytes. Therefore, poly(para‐phyenylene) (PPP) was electrochemically synthesized in the two representative RTILs: bmimPF6 and bmiTf2N (imidazolium and pyrrolidinium‐based salts, respectively). It was found that the electrochemical synthesis of PPP was significantly enhanced in bmimPF6. Additionally, the results from doping studies of PPP films indicate improved electroactivity in bmimPF6 during oxidation (p‐doping) and in bmiTf2N in the case of reduction (n‐doping). These findings were supported by in situ infrared spectroscopy studies. Conducting poly(benzimidazobenzophenanthroline) (BBL) is a material which can provide relatively high field‐effect mobility of charge carriers in OFET devices. The main disadvantage of this n‐type semiconductor is its limited processability. Therefore in this work BBL was functionalized with poly(ethylene oxide) PEO, varying the length of side chains enabling water dispersions of the studied polymer. It was found that functionalization did not distract the electrochemical activity of the BBL backbone while the processability was improved significantly in comparison to conventional BBL. Another objective was to study highly processable poly(3,4‐ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) water‐based inks for controlled patterning scaled‐down to nearly a nanodomain with the intention to fabricate various chemical sensors. Developed PEDOT:PSS inks greatly improved printing of nanoarrays and with further modification with quaternary ammonium cations enabled fabrication of PEDOT:PSS‐based chemical sensors for lead (II) ions with enhanced adhesion and stability in aqueous environments. This opens new possibilities for development of PEDOT:PSS films that can be used in bio‐related applications. Polycyclic aromatic hydrocarbons (PAHs) are a broad group of π‐conjugated materials consisting of aromatic rings in the range from naphthalene to even hundred rings in one molecule. The research on this type of materials is intriguing, due to their interesting optical properties and resemblance of graphene. The objective was to use electrochemical synthesis to yield relatively large PAHs and fabricate electroactive films that could be used as template material in chemical sensors. Spectroscopic, electrochemical and electrical investigations evidence formation of highly stable films with fast redox response, consisting of molecules with 40 to 60 carbon atoms. Additionally, this approach in synthesis, starting from relatively small PAH molecules was successfully used in chemical sensor for lead (II).