Quantile Estimation in Non-Stationary Streaming Data

We provide an incremental quantile estimator for Non-stationary Streaming Data. We propose a method for simultaneous estimation of multiple quantiles corresponding to the given probability levels from streaming data. Due to the limitations of the memory, it is not feasible to compute the quantiles by storing the data. So estimating the quantiles as the data pass by is the only possibility. This can be effective in network measurement. To provide the minimum of the mean-squared error of the estimation, we use parabolic approximation and for comparison we simulate the results for different number of runs and using both linear and parabolic approximations.

Analysis of torque and speed ripple producing non-idealities of frequency converters in electric drives

Electric motors driven by adjustable-frequency converters may produce periodic excitation forces that can cause torque and speed ripple. Interaction with the driven mechanical system may cause undesirable vibrations that affect the system performance and lifetime. Direct drives in sensitive applications, such as elevators or paper machines, emphasize the importance of smooth torque production. This thesis analyses the non-idealities of frequencyconverters that produce speed and torque ripple in electric drives. The origin of low order harmonics in speed and torque is examined. It is shown how different current measurement error types affect the torque. As the application environment, direct torque control (DTC) method is applied to permanent magnet synchronous machines (PMSM). A simulation model to analyse the effect of the frequency converter non-idealities on the performance of the electric drives is created. Themodel enables to identify potential problems causing torque vibrations and possibly damaging oscillations in electrically driven machine systems. The model is capable of coupling with separate simulation software of complex mechanical loads. Furthermore, the simulation model of the frequency converter's control algorithm can be applied to control a real frequency converter. A commercial frequencyconverter with standard software, a permanent magnet axial flux synchronous motor and a DC motor as the load are used to detect the effect of current measurement errors on load torque. A method to reduce the speed and torque ripple by compensating the current measurement errors is introduced. The method is based on analysing the amplitude of a selected harmonic component of speed as a function oftime and selecting a suitable compensation alternative for the current error. The speed can be either measured or estimated, so the compensation method is applicable also for speed sensorless drives. The proposed compensation method is tested with a laboratory drive, which consists of commercial frequency converter hardware with self-made software and a prototype PMSM. The speed and torque rippleof the test drive are reduced by applying the compensation method. In addition to the direct torque controlled PMSM drives, the compensation method can also beapplied to other motor types and control methods.

Problems of the architecture design in the system integration

This thesis studies the problems and their reasons a software architect faces in his work. The purpose of the study is to search and identify potential factors causing problens in system integration and software engineering. Under a special interest are non-technical factors causing different kinds of problems. Thesis was executed by interviewing professionals that took part in e-commerce project in some corporation. Interviewed professionals consisted of architects from technical implementation projects, corporation's architect team leader, different kind of project managers and CRM manager. A specific theme list was used as an guidance of the interviews. Recorded interviews were transcribed and then classified using ATLAS.ti software. Basics of e-commerce, software engineering and system integration is described too. Differences between e-commerce and e-business as well as traditional business are represented as are basic types of e-commerce. Software's life span, general problems of software engineering and software design are covered concerning software engineering. In addition, general problems of the system integration and the special requirements set by e-commerce are described in the thesis. In the ending there is a part where the problems founded in study are described and some areas of software engineering where some development could be done so that same kind of problems could be avoided in the future.

Non-wood massojen vedenpoiston arvioiminen märkäpuristuksessa

Yksivuotisten kasvien (non-wood) kuitua verrataan usein lehtipuukuituihin. Käytetyimpiä non-wood kasveja ovat vehnän olki, bambu, järviruoko ja bagassi. Non-wood massan erottaa puumassasta kuitenkin korkea silikaattipitoisuus sekä parenkyymisolupitoisuus, joka antaa massalle korkean hienoainepitoisuuden. Tämä yhdessä korkean hemiselluloosapitoisuuden ja lyhyen kuidun pituuden kanssa heikentävät voimakkaasti non-wood massan vedenpoisto-ominaisuuksia. Non-wood kuidulla voidaan korvata lehtipuumassaa hienopapereissa. Non-wood kuitu antaa paperille hyvän opasiteetin, korkean valonsirontakertoimen sekä sileän painopinnan. Massaan lisättävä pitkäkuituinen havupuumassa parantaa ajetta¬vuutta paperikoneella ja helpottaa massan vedenpoistoa. Non-wood massan vedenpoistoa voidaan tehostaa esimerkiksi poistamalla osa hienoaineesta, käyttämällä non-wood massalle sopivaa keittotapaa sekä käyttämällä märkä¬puristuksessa pitkänippityyppistä puristinratkaisua. Myös non-wood kuidun kuivaaminen parantaa vedenpoistoa. Tässä tutkimuksessa kirjallisuusosassa keskityttiin yleisimpiin paperin valmistuksessa käytettäviin non-wood kuidun lähteisiin, märkäpuristuksen teoriaan ja tapoihin tehostaa vedenpoistoa. Kokeellisessa osassa tutkittiin vehnänolkimassan käyttäytymistä märkäpuristuksessa erilaisten ominaisuuksien pohjalta. Tutkimuksen kohteena oli non-wood massan keittotapa (hapan/alkali), hienoainepitoisuus, silikaattipitoisuus sekä kuivattu/kuivaamaton kuitu. Vertailun vuoksi tutkimuksessa oli mukana myös yksi järviruokomassa. Tuloksista huomataan, että non-wood massan vedenpoistoon vaikuttaa hienoainepitoisuus, kuidun kuivaus sekä massan valmistustapa. Järviruokomassan veden¬poisto on tehokkaampaa kuin vehnänolkimassan paremman kuitu¬koostumuksensa takia. Jos hienopaperimassassa korvataan lehtipuumassaa non-wood kuidulla maksimissaan 40 %, massan vedenpoistoa voidaan hyvin arvioida erilaisten suotautuvuusmittojen, kuten freeneksen, vedenpidätyskyvyn ja suotautumisajan, avulla.

Sensory and Non-sensory Factors Behind the Liking and Choice of Healthy Food Products

A healthy and balanced diet can reduce health problems, such as overweight and metabolic syndrome. In general, people have a considerably good knowledge of what constitutes a healthy diet and how they could achieve it with their food choices. Besides, people argue that health is among their top five food choice motives. Nevertheless, the prevalence of overweight is increasing and other food choice motives, such as taste, seem to conflict with the health. Liking for food does not necessarily determine acceptance alone, thus several non-sensory factors, such as brand, country of origin and nutrition claim, can also influence. Moreover, consumers are individuals in how they prioritize sensory and nonsensory factors of foods, but e.g. increasing age, female gender and health concern have been connected to a more health-oriented dietary behaviour. To sum up, identifying different factors that can increase the liking and consumption of healthy food is essential in order to develop more attractive healthful food products. Adding vitamins, minerals, fibre or other ingredients to a food product can be used to enrich the nutritional quality of the products. However, this may be difficult in practice as regards the sensory quality and pleasantness of the foods. Generally, consumers are not willing to compromise on taste in food. On the other hand, consumers are very heterogeneous in their likings, and their personal values and attitudes may interact with preferences for specific sensory characteristics. The aims of this study were to investigate the effects of intrinsic product characteristics on sensory properties and hedonic responses; to determine the impact of few non-sensory factors; and to examine the interaction between sensory and non-sensory factors with consumers’ demographics, values and attitudes in liking of healthy model foods. The results showed that product composition influenced sensory quality and had an effect on hedonic responses. Adding flaxseed to bakery products showed a significant improvement in the nutritional quality without negative effects on sensory properties. On the other hand, the fortification of wellness beverages with vitamins and minerals may impart off-flavours. In general, sweetness of yoghurts, freshness of wellness beverages and low intensity of rye bread flavour appealed to consumers. Information about the domestic origin of yoghurts and claiming a specific function for wellness beverages enhanced liking. However, consumers who were more concerned about their health and considered natural content as an important food choice motive, rated sourer and less sweet yoghurts and wellness beverages as more pleasant. In addition, interest in health increased the consumption of rye breads and other whole grain breads among adolescents. The results showed that the optimal product quality in terms of intrinsic and extrinsic factors differs between individual consumers, and personal values and food choice motives can be connected to preferences for specific sensory characteristics of foods. This indicates that each food product needs to be considered in relation to its specific market niche, and to which segment of consumer will respond most positively to its characteristics.

Utilization of retention chemicals in non-wood containing furnishes

The usage of the non-wood pulps in furnishes for various paper grades is the real alternative for substitution of wood fibres in the papermaking. This is especially important now, when the prices for wood are increasing and forest resources are depleting in many regions of our planet. However, there are several problems associated with utilization of such pulps. In terms of the papermaking process one of the main problems is the poor dewatering of the non-wood pulps. This problem can be partially solved by means of retention aids. In the literature part were described technological features of the non-wood pulps as the raw materials for paper production. Moreover, overviews of the retention chemicals and methods for retention measurement were done; special attention was paid to the mechanisms of retention and drainage. Finally, factors affecting on the drainage and retention of non-wood pulps were considered holistically. Particular emphasis was put on the possibility of enzyme treatment for drainage improvement. It was stated that retention aids can significantly improve dewatering of non-wood pulps. In the experimental part the goal was to investigate influence of various microparticle retention aids on the drainage, retention and formation of furnish containing wheat straw pulp, obtained by novel pulping process (Formico™Fib). The parallel test were performed with reference furnish containing only wood pulps. It was found that Bentonite-CPAM retention aid can significantly improve drainage and retention; however formation seems be suffer from such additives. It was stated that performance of the Silica-Starch retention aid significantly depends on the starch dosing sequence and wet-end conditions; this system have shown better formation than other tested retention aids. Silica-CPAM retention aid have provided comparable results in retention and drainage with Bentonite-CPAM, while Silica-starch did not improve dewatering and yielded in lowest filler retention among other aids. Ultimately, optimal dosages for the tested retention chemicals have been suggested.

On convergence of transforms based on parabolic scaling

This thesis studies properties of transforms based on parabolic scaling, like Curvelet-, Contourlet-, Shearlet- and Hart-Smith-transform. Essentially, two di erent questions are considered: How these transforms can characterize H older regularity and how non-linear approximation of a piecewise smooth function converges. In study of Hölder regularities, several theorems that relate regularity of a function f : R2 → R to decay properties of its transform are presented. Of particular interest is the case where a function has lower regularity along some line segment than elsewhere. Theorems that give estimates for direction and location of this line, and regularity of the function are presented. Numerical demonstrations suggest also that similar theorems would hold for more general shape of segment of low regularity. Theorems related to uniform and pointwise Hölder regularity are presented as well. Although none of the theorems presented give full characterization of regularity, the su cient and necessary conditions are very similar. Another theme of the thesis is the study of convergence of non-linear M ─term approximation of functions that have discontinuous on some curves and otherwise are smooth. With particular smoothness assumptions, it is well known that squared L2 approximation error is O(M-2(logM)3) for curvelet, shearlet or contourlet bases. Here it is shown that assuming higher smoothness properties, the log-factor can be removed, even if the function still is discontinuous.

Experimental Studies on Non-Metallic Composite Bone Implants With a Special Reference to Staphylococcal Biofilm Infection

Non-metallic implants made of bioresorbable or biostable synthetic polymers are attractive options in many surgical procedures, ranging from bioresorbable suture anchors of arthroscopic surgery to reconstructive skull implants made of biostable fiber-reinforced composites. Among other benefits, non-metallic implants produce less interference in imaging. Bioresorbable polymer implants may be true multifunctional, serving as osteoconductive scaffolds and as matrices for simultaneous delivery of bone enhancement agents. As a major advantage for loading conditions, mechanical properties of biostable fiber-reinforced composites can be matched with those of the bone. Unsolved problems of these biomaterials are related to the risk of staphylococcal biofilm infections and to the low osteoconductivity of contemporary bioresorbable composite implants. This thesis was focused on the research and development of a multifunctional implant model with enhanced osteoconductivity and low susceptibility to infection. In addition, the experimental models for assessment, diagnostics and prophylaxis of biomaterial-related infections were established. The first experiment (Study I) established an in vitro method for simultaneous evaluation of calcium phosphate and biofilm formation on bisphenol-Aglycidyldimethacrylate and triethylenglycoldimethacrylate (BisGMA-TEGDMA) thermosets with different content of bioactive glass 45S5. The second experiment (Study II) showed no significant difference in osteointegration of nanostructured and microsized polylactide-co-glycolide/β-tricalcium phosphate (PLGA /β-TCP) composites in a minipig model. The third experiment (Study III) demonstrated that positron emission tomography (PET) imaging with the novel 68Ga labelled 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid (DOTA) CD33 related sialic-acid immunoglobulin like lectins (Siglec-9) tracer was able to detect inflammatory response to S. epidermidis and S. aureus peri-implant infections in an intraosseous polytetrafluoroethylene catheter model. In the fourth experiment (Study IV), BisGMATEGDMA thermosets coated with lactose-modified chitosan (Chitlac) and silver nanoparticles exhibited antibacterial activity against S. aureus and P. aeruginosa strains in an in vitro biofilm model and showed in vivo biocompatibility in a minipig model. In the last experiment (Study V), a selective androgen modulator (SARM) released from a poly(lactide)-co-ε-caprolactone (PLCL) polymer matrix failed to produce a dose-dependent enhancement of peri-implant osteogenesis in a bone marrow ablation model.

Measurement of social value creation with non-financial measures

This research examines the concept of social entrepreneurship which is a fairly new business model. In the field of business it has become increasingly popular in recent years. The growing awareness of the environment and concrete examples of impact created by social entrepreneurship have encouraged entrepreneurs to address social problems. Society’s failures are tried to redress as a result of business activities. The purpose of doing business is necessarily no longer generating just profits but business is run in order to make a social change with the profit gained from the operations. Successful social entrepreneurship requires a specific nature, constant creativity and strong desire to make a social change. It requires constant balancing between two major objectives: both financial and non-financial issues need to be considered, but not at the expense of another. While aiming at the social purpose, the business needs to be run in highly competitive markets. Therefore, both factors need equally be integrated into an organization as they are complementary, not exclusionary. Business does not exist without society and society cannot go forward without business. Social entrepreneurship, its value creation, measurement tools and reporting practices are under discussion in this research. An extensive theoretical basis is covered and used to support the findings coming out of the researched case enterprises. The most attention is focused on the concept of Social Return on Investment. The case enterprises are analyzed through the SROI process. Social enterprises are mostly small or medium sized. Naturally this sets some limitations in implementing measurement tools. The question of resources requires the most attention and therefore sets the biggest constraints. However, the size of the company does not determine all – the nature of business and the type of social purpose need to be considered always. The mission may be so concrete and transparent that in all cases any kind of measurement would be useless. Implementing measurement tools may be of great benefit – or a huge financial burden. Thus, the very first thing to carefully consider is the possible need of measuring value creation.

Variational ensemble Kalman filtering applied to data assimilation problems in computational fluid dynamics

One challenge on data assimilation (DA) methods is how the error covariance for the model state is computed. Ensemble methods have been proposed for producing error covariance estimates, as error is propagated in time using the non-linear model. Variational methods, on the other hand, use the concepts of control theory, whereby the state estimate is optimized from both the background and the measurements. Numerical optimization schemes are applied which solve the problem of memory storage and huge matrix inversion needed by classical Kalman filter methods. Variational Ensemble Kalman filter (VEnKF), as a method inspired the Variational Kalman Filter (VKF), enjoys the benefits from both ensemble methods and variational methods. It avoids filter inbreeding problems which emerge when the ensemble spread underestimates the true error covariance. In VEnKF this is tackled by resampling the ensemble every time measurements are available. One advantage of VEnKF over VKF is that it needs neither tangent linear code nor adjoint code. In this thesis, VEnKF has been applied to a two-dimensional shallow water model simulating a dam-break experiment. The model is a public code with water height measurements recorded in seven stations along the 21:2 m long 1:4 m wide flume’s mid-line. Because the data were too sparse to assimilate the 30 171 model state vector, we chose to interpolate the data both in time and in space. The results of the assimilation were compared with that of a pure simulation. We have found that the results revealed by the VEnKF were more realistic, without numerical artifacts present in the pure simulation. Creating a wrapper code for a model and DA scheme might be challenging, especially when the two were designed independently or are poorly documented. In this thesis we have presented a non-intrusive approach of coupling the model and a DA scheme. An external program is used to send and receive information between the model and DA procedure using files. The advantage of this method is that the model code changes needed are minimal, only a few lines which facilitate input and output. Apart from being simple to coupling, the approach can be employed even if the two were written in different programming languages, because the communication is not through code. The non-intrusive approach is made to accommodate parallel computing by just telling the control program to wait until all the processes have ended before the DA procedure is invoked. It is worth mentioning the overhead increase caused by the approach, as at every assimilation cycle both the model and the DA procedure have to be initialized. Nonetheless, the method can be an ideal approach for a benchmark platform in testing DA methods. The non-intrusive VEnKF has been applied to a multi-purpose hydrodynamic model COHERENS to assimilate Total Suspended Matter (TSM) in lake Säkylän Pyhäjärvi. The lake has an area of 154 km2 with an average depth of 5:4 m. Turbidity and chlorophyll-a concentrations from MERIS satellite images for 7 days between May 16 and July 6 2009 were available. The effect of the organic matter has been computationally eliminated to obtain TSM data. Because of computational demands from both COHERENS and VEnKF, we have chosen to use 1 km grid resolution. The results of the VEnKF have been compared with the measurements recorded at an automatic station located at the North-Western part of the lake. However, due to TSM data sparsity in both time and space, it could not be well matched. The use of multiple automatic stations with real time data is important to elude the time sparsity problem. With DA, this will help in better understanding the environmental hazard variables for instance. We have found that using a very high ensemble size does not necessarily improve the results, because there is a limit whereby additional ensemble members add very little to the performance. Successful implementation of the non-intrusive VEnKF and the ensemble size limit for performance leads to an emerging area of Reduced Order Modeling (ROM). To save computational resources, running full-blown model in ROM is avoided. When the ROM is applied with the non-intrusive DA approach, it might result in a cheaper algorithm that will relax computation challenges existing in the field of modelling and DA.