Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Proportionality and Party Success in Europe

This thesis consists of four articles and an introductory section. The main research questions in all the articles are about proportionality and party success in Europe, at European, national or district levels. Proportionality in this thesis denotes the proximity of seat shares parties receive compared to their respective vote shares, after the electoral system’s allocation process. This proportionality can be measured through numerous indices that illustrate either the overall proportionality of an electoral system or a particular election. The correspondence of a single party’s seat shares to its vote shares can also be measured. The overall proportionality is essential in three of the articles (1, 2 and 4), where the system’s performance is studied by means of plots. In article 3, minority party success is measured by advantage-ratios that reveal single party’s winnings or losses in the votes to seat allocation process. The first article asks how proportional are the European parliamentary (EP) electoral systems, how do they compare with results gained from earlier studies and how do the EP electoral systems treat different sized parties. The reasons for different outcomes are looked for in explanations given by traditional electoral studies i.e. electoral system variables. The countries studied (EU15) apply electoral systems that vary in many important aspects, even though a certain amount of uniformity has been aspired to for decades. Since the electoral systems of the EP elections closely resemble the national elections, the same kinds of profiles emerge as in the national elections. The electoral systems indeed treat the parties differentially and six different profile types can be found. The counting method seems to somewhat determine the profile group, but the strongest variables determining the shape of a countries’ profile appears to be the average district magnitude and number of seats allocated to each country. The second article also focuses on overall proportionality performance of an electoral system, but here the focus is on the impact of electoral system changes. I have developed a new method of visualizing some previously used indices and some new indices for this purpose. The aim is to draw a comparable picture of these electoral systems’ changes and their effects. The cases, which illustrate this method, are four elections systems, where a change has occurred in one of the system variables, while the rest remained unchanged. The studied cases include the French, Greek and British European parliamentary systems and the Swedish national parliamentary system. The changed variables are electoral type (plurality changed to PR in the UK), magnitude (France splitting the nationwide district into eight smaller districts), legal threshold (Greece introducing a three percent threshold) and counting method (d’Hondt was changed to modified Sainte-Laguë in Sweden). The radar plots from elections after and before the changes are drawn for all country cases. When quantifying the change, the change in the plots area that is created has also been calculated. Using these radar plots we can observe that the change in electoral system type, magnitude, and also to some extent legal threshold had an effect on overall proportionality and accessibility for small parties, while the change between the two highest averages counting method had none. The third article studies the success minority parties have had in nine electoral systems in European heterogeneous countries. This article aims to add more motivation as to why we should care how different sized parties are treated by the electoral systems. Since many of the parties that aspire to represent minorities in European countries are small, the possibilities for small parties are highlighted. The theory of consociational (or power-sharing) democracy suggests that, in heterogeneous societies, a proportional electoral system will provide the fairest treatment of minority parties. The OSCE Lund Recommendations propose a number of electoral system features, which would improve minority representation. In this article some party variables, namely the unity of the minority parties and the geographical concentration of the minorities were included among possible explanations. The conclusions are that the central points affecting minority success were indeed these non-electoral system variables rather than the electoral system itself. Moreover, the size of the party was a major factor governing success in all the systems investigated; large parties benefited in all the studied electoral systems. In the fourth article the proportionality profiles are again applied, but this time to district level results in Finnish parliamentary elections. The level of proportionality distortion is also studied by way of indices. The average magnitudes during the studied periodrange from 7.5 to 26.2 in the Finnish electoral districts and this opens up unequal opportunities for parties in different districts and affects the shape of the profiles. The intra-country case allows the focus to be placed on the effect of district magnitude, since all other electoral systems are kept constant in an intra-country study. The time span in the study is from 1962 to 2007, i.e. the time that the districts have largely been the same geographically. The plots and indices tell the same story, district magnitude and electoral alliances matter. The district magnitude is connected to the overall proportionality of the electoral districts according to both indices, and the profiles are, as expected, also closer to perfect proportionality in large districts. Alliances have helped some small parties to gain a much higher seat share than their respective vote share and these successes affect some of the profiles. The profiles also show a consistent pattern of benefits for the small parties who ally with the larger parties.

Targeted Therapy Possibilities for Metastatic Melanoma

The incidence of malignant melanoma of the skin has been steadily rising worldwide during the past decades. Most early detected primary tumors can be removed surgically and the prognosis is good. However, at the same time there still is no permanent cure for metastatic melanoma and its prognosis is poor, although lately new effective drugs have emerged. In this thesis, four different approaches of experimental therapy for metastatic melanoma were studied. Endogenous cis-Urocanic acid (UCA) is found in every individual’s skin, where exposure to UV light from the sun generates it from its inactive trans conformation. Cis- UCA was found to destroy malignant melanoma cells in culture under an acidified pH and sufficient concentration through caspase-3 mediated apoptosis. Furthermore, cis-UCA is able to considerably diminish the growth rate in human melanoma tumors on living SCID mice. Using replication-competent Semliki Forest viruses, human melanoma tumors grown in SCID mice were dramatically shrunken as the fulminant production of viruses in melanoma cells leads them to apoptosis within 72 hours. Small oligopeptides attaching to melanoma cells were identified using in vivo phage display. The melanoma-specific peptides found were further tested in vitro on adenoviruses. Ultimately, the adenoviral retargeting using the peptides was tested in vivo. One peptide homed to human transferring receptor upregulated on melanoma cells. In order to kill the malignant melanoma cells with the retargeted adenoviruses, the viruses should carry genetic material producing apoptotic proteins in the cancer tissue. TIMP-3 has been identified as a good candidate for such a protein, as it inhibits malignant cell adhesion as well as promotes apoptosis through a caspase-8 pathway. It is further shown here that adenovirally delivered TIMP-3 is even more potent, as it could kill non-adherent cancer cells, lacking the fully functional death receptor signalling pathway. Adenovirally delivered TIMP-2 also showed marked antitumor effects in human malignant melanoma xenografts on SCID mice both in ex vivo and systemic delivery.

A Farewell to Flat Biology. Three-dimensional Cell Culture Models in Cancer Drug Target Identification and Validation

Cells of epithelial origin, e.g. from breast and prostate cancers, effectively differentiate into complex multicellular structures when cultured in three-dimensions (3D) instead of conventional two-dimensional (2D) adherent surfaces. The spectrum of different organotypic morphologies is highly dependent on the culture environment that can be either non-adherent or scaffold-based. When embedded in physiological extracellular matrices (ECMs), such as laminin-rich basement membrane extracts, normal epithelial cells differentiate into acinar spheroids reminiscent of glandular ductal structures. Transformed cancer cells, in contrast, typically fail to undergo acinar morphogenic patterns, forming poorly differentiated or invasive multicellular structures. The 3D cancer spheroids are widely accepted to better recapitulate various tumorigenic processes and drug responses. So far, however, 3D models have been employed predominantly in the Academia, whereas the pharmaceutical industry has yet to adopt a more widely and routine use. This is mainly due to poor characterisation of cell models, lack of standardised workflows and high throughput cell culture platforms, and the availability of proper readout and quantification tools. In this thesis, a complete workflow has been established entailing well-characterised 3D cell culture models for prostate cancer, a standardised 3D cell culture routine based on high-throughput-ready platform, automated image acquisition with concomitant morphometric image analysis, and data visualisation, in order to enable large-scale high-content screens. Our integrated suite of software and statistical analysis tools were optimised and validated using a comprehensive panel of prostate cancer cell lines and 3D models. The tools quantify multiple key cancer-relevant morphological features, ranging from cancer cell invasion through multicellular differentiation to growth, and detect dynamic changes both in morphology and function, such as cell death and apoptosis, in response to experimental perturbations including RNA interference and small molecule inhibitors. Our panel of cell lines included many non-transformed and most currently available classic prostate cancer cell lines, which were characterised for their morphogenetic properties in 3D laminin-rich ECM. The phenotypes and gene expression profiles were evaluated concerning their relevance for pre-clinical drug discovery, disease modelling and basic research. In addition, a spontaneous model for invasive transformation was discovered, displaying a highdegree of epithelial plasticity. This plasticity is mediated by an abundant bioactive serum lipid, lysophosphatidic acid (LPA), and its receptor LPAR1. The invasive transformation was caused by abrupt cytoskeletal rearrangement through impaired G protein alpha 12/13 and RhoA/ROCK, and mediated by upregulated adenylyl cyclase/cyclic AMP (cAMP)/protein kinase A, and Rac/ PAK pathways. The spontaneous invasion model tangibly exemplifies the biological relevance of organotypic cell culture models. Overall, this thesis work underlines the power of novel morphometric screening tools in drug discovery.

Fluorescence-based imaging of cellular defect in lysinuric protein intolerance (LPI)

Fluoresenssiperusteiset kuvantamismenetelmät lysinurisen proteiini-intoleranssin (LPI) soluhäiriön tutkimuksessa Lysinurinen proteiini-intoleranssi on suomalaiseen tautiperintöön kuuluva autosomaalisesti peit¬tyvästi periytyvä sairaus, jonka aiheuttaa kationisten aminohappojen kuljetushäiriö munuaisten ja ohutsuolen epiteelisolujen basolateraalikalvolla. Aminohappojen kuljetushäiriö johtaa moniin oirei¬siin, kuten kasvuhäiriöön, osteoporoosiin, immuunijärjestelmän häiriöihin, oksenteluun ja runsaspro¬teiinisen ravinnon nauttimisen jälkeiseen hyperammonemiaan. LPI-geeni SLC7A7 (solute carrier family 7 member 7) koodaa y+LAT1 proteiinia, joka on basolateraali¬nen kationisten ja neutraalien aminohappojen kuljettimen kevyt ketju, joka muodostaa heterodimee¬rin raskaan alayksikön 4F2hc:n kanssa. Tällä hetkellä SLC7A7-geenistä tunnetaan yli 50 LPI:n aiheut¬tavaa mutaatiota. Tässä tutkimuksessa erityyppisiä y+LAT1:n LPI-mutaatiota sekä yhdeksän C-terminaalista polypep¬tidiä lyhentävää deleetiota kuvannettiin nisäkässoluissa y+LAT1:n GFP (green fluorescent protein) -fuusioproteiineina. Tulokset vahvistivat muissa soluissa tehdyt havainnot siitä, että 4F2hc on edel¬lytyksenä y+LAT1:n solukalvokuljetukselle, G54V-pistemutantti sijaitsee solukalvolla samoin kuin vil¬lityyppinen proteiini, mutta lukukehystä muuttavia ja proteiinia lyhentäviä mutantteja ei kuljeteta solukalvoon. Lisäksi havaittiin, että poikkeuksena tästä säännöstä ovat y+LAT1-deleetioproteiinit, joista puuttui korkeintaan 50 C-terminaalista aminohappoa. Nämä lyhentyneet kuljettimet sijaitsevat solukalvolla kuten villityyppiset ja LPI-pistemutanttiproteiinit. Dimerisaation osuutta kuljetushäiriön synnyssä tutkittiin käyttämällä fluorescence resonance energy transfer (FRET) menetelmää. Heterodimeerin alayksiköistä kloonattiin ECFP (cyan) ja EYFP (yellow) fuusioproteiinit, joita ilmennettiin nisäkässoluissa, ja FRET mitattiin virtaussytometri-FRET -menetel¬mällä (FACS-FRET). Tutkimuksissa kaikkien mutanttien havaittiin dimerisoituvan yhtä tehokkaasti. Kul¬jetushäiriön syynä ei siten ole alayksiköiden dimerisaation estyminen mutaation seurauksena. Tutkimuksessa havaittiin, että kaikki mutantti-y+LAT1-transfektiot tuottavat vähemmän transfektoi¬tuneita soluja kuin villityyppisen y+LAT1:n transfektiot. Solupopulaatioissa, joihin oli tranfektoitu lu¬kukehystä muuttava tai stop-kodonin tuottava mutaatio havaittiin suurempi kuolleisuus kuin saman näytteen transfektoitumattomissa soluissa, kun taas villityyppistä tai G54V-pistemutanttia tuottavas¬sa solupopulaatiossa oli pienempi kuolleisuus kuin saman näytteen fuusioproteiinia ilmentämättö¬missä soluissa. Tulos osoittaa mutanttiproteiinien erilaiset vaikutukset niitä ilmentäviin soluihin, joko suoraan y+LAT1:n tai 4F2hc:n kautta aiheutuneina. LPIFin SLC7A7 lähetti-RNA:n määrä ei merkittävästi poikennut villityyppisen määrästä fibroblasteissa ja lymfoblasteissa. SLC7A7:n promoottorianalyysissä oli osoitettavissa säätelyalueita geenin 5’ ei-koo¬daavalla alueella sekä ensimmäisten kahden intronin alueella. LPI-taudin tautimekanismin kannalta keskeisin tekijä on kuitenkin aminohappokuljetuksen häiriö, jonka vaikutuksesta näistä aminohapoista riippuvaiset prosessit elimistössä eivät toimi normaalisti. Havaittu virheellinen y+LAT1/4F2hc kuljetuskompleksin sijainti edellyttää lisätutkimuksia sen mahdol¬lisen kliinisen merkityksen selvittämiseksi.

Transparent and secure remote network storage system using an untrusted server

Työssä kehitettin läpinäkyvä Internet Small Computer Systems Interface-verkkolevyä (iSCSI) käyttävä varmistusjärjestelmä. Verkkolevyn sisältö suojattiin asiakaspään salauskerroksella (dm-crypt). Järjestely mahdollisti sen, että verkkolevylle tallennetut varmuuskopiot pysyivät luottamuksellisina, vaikka levypalvelinta tarjoava taho oli joko epäluotettava tai suorastaan vihamielinen. Järjestelmän hyötykäyttöä varten kehitettiin helppokäyttöinen prototyyppisovellus. Järjestelmän riskit ja haavoittuvuudet käytiin läpi ja analysoitiin. Järjestelmälle tehtiin myös karkea kryptoanalyysi sen teknistenominaisuuksien pohjalta. Suorituskykymittaukset tehtiin sekä salatulle että salaamattomalle iSCSI-liikenteelle. Näistä todettiin, että salauksen vaikutus suorituskykyyn oli häviävän pieni jopa 100 megabittiä sekunnissa siirtävillä verkkonopeuksilla. Lisäksi pohdittiin teknologian muita sovelluskohteita ja tulevia tutkimusalueita.

On Modelling, System Identification and Control of Servo-Systems with a Flexible Load

The present study was done with two different servo-systems. In the first system, a servo-hydraulic system was identified and then controlled by a fuzzy gainscheduling controller. The second servo-system, an electro-magnetic linear motor in suppressing the mechanical vibration and position tracking of a reference model are studied by using a neural network and an adaptive backstepping controller respectively. Followings are some descriptions of research methods. Electro Hydraulic Servo Systems (EHSS) are commonly used in industry. These kinds of systems are nonlinearin nature and their dynamic equations have several unknown parameters.System identification is a prerequisite to analysis of a dynamic system. One of the most promising novel evolutionary algorithms is the Differential Evolution (DE) for solving global optimization problems. In the study, the DE algorithm is proposed for handling nonlinear constraint functionswith boundary limits of variables to find the best parameters of a servo-hydraulic system with flexible load. The DE guarantees fast speed convergence and accurate solutions regardless the initial conditions of parameters. The control of hydraulic servo-systems has been the focus ofintense research over the past decades. These kinds of systems are nonlinear in nature and generally difficult to control. Since changing system parameters using the same gains will cause overshoot or even loss of system stability. The highly non-linear behaviour of these devices makes them ideal subjects for applying different types of sophisticated controllers. The study is concerned with a second order model reference to positioning control of a flexible load servo-hydraulic system using fuzzy gainscheduling. In the present research, to compensate the lack of dampingin a hydraulic system, an acceleration feedback was used. To compare the results, a pcontroller with feed-forward acceleration and different gains in extension and retraction is used. The design procedure for the controller and experimental results are discussed. The results suggest that using the fuzzy gain-scheduling controller decrease the error of position reference tracking. The second part of research was done on a PermanentMagnet Linear Synchronous Motor (PMLSM). In this study, a recurrent neural network compensator for suppressing mechanical vibration in PMLSM with a flexible load is studied. The linear motor is controlled by a conventional PI velocity controller, and the vibration of the flexible mechanism is suppressed by using a hybrid recurrent neural network. The differential evolution strategy and Kalman filter method are used to avoid the local minimum problem, and estimate the states of system respectively. The proposed control method is firstly designed by using non-linear simulation model built in Matlab Simulink and then implemented in practical test rig. The proposed method works satisfactorily and suppresses the vibration successfully. In the last part of research, a nonlinear load control method is developed and implemented for a PMLSM with a flexible load. The purpose of the controller is to track a flexible load to the desired position reference as fast as possible and without awkward oscillation. The control method is based on an adaptive backstepping algorithm whose stability is ensured by the Lyapunov stability theorem. The states of the system needed in the controller are estimated by using the Kalman filter. The proposed controller is implemented and tested in a linear motor test drive and responses are presented.

Analysis of torque and speed ripple producing non-idealities of frequency converters in electric drives

Electric motors driven by adjustable-frequency converters may produce periodic excitation forces that can cause torque and speed ripple. Interaction with the driven mechanical system may cause undesirable vibrations that affect the system performance and lifetime. Direct drives in sensitive applications, such as elevators or paper machines, emphasize the importance of smooth torque production. This thesis analyses the non-idealities of frequencyconverters that produce speed and torque ripple in electric drives. The origin of low order harmonics in speed and torque is examined. It is shown how different current measurement error types affect the torque. As the application environment, direct torque control (DTC) method is applied to permanent magnet synchronous machines (PMSM). A simulation model to analyse the effect of the frequency converter non-idealities on the performance of the electric drives is created. Themodel enables to identify potential problems causing torque vibrations and possibly damaging oscillations in electrically driven machine systems. The model is capable of coupling with separate simulation software of complex mechanical loads. Furthermore, the simulation model of the frequency converter's control algorithm can be applied to control a real frequency converter. A commercial frequencyconverter with standard software, a permanent magnet axial flux synchronous motor and a DC motor as the load are used to detect the effect of current measurement errors on load torque. A method to reduce the speed and torque ripple by compensating the current measurement errors is introduced. The method is based on analysing the amplitude of a selected harmonic component of speed as a function oftime and selecting a suitable compensation alternative for the current error. The speed can be either measured or estimated, so the compensation method is applicable also for speed sensorless drives. The proposed compensation method is tested with a laboratory drive, which consists of commercial frequency converter hardware with self-made software and a prototype PMSM. The speed and torque rippleof the test drive are reduced by applying the compensation method. In addition to the direct torque controlled PMSM drives, the compensation method can also beapplied to other motor types and control methods.

High Performance Electrical Drive System for a Biomechanical Test and Rehabilitation Equipment

Suunniteltiin ja rakennettiin suoraa vääntömomenttisäätöä soveltava taajuudenmuuttajakäyttö oikosulkumoottorin ohjaukseen korvaamaan passiivinen jarrukäyttö. Laite on kuntoutuslaite, jolla tehdään lihasvoiman mittauksia ja voimaharjoituksia. Selvitettiin kaupallisten moottoreiden ja taajuudenmuuttajien suoritusominaisuuksia ja tämän perusteella valittiin käyttöön sopivat laitteet. Työssä esitetään kaksi oikosulkumoottorin ohjaustapaa: vektorisäätö ja suora vääntömomenttisäätö. Merkittävin osa tästä työstä käsittelee - tarkan turvallisuussuunnitelman lisäksi - kuntoutuslaitteen prototyypin komponentteja, kokoamista ja suoritustestien tuloksia.

Improving ERP change tool processes to align business processes and ERP system

Nopea teknologian kehitys sekä kansainvälistymisen mukana tuoma kilpailupaine pakottavat yritykset jatkuvaan liiketoimintaprosessien kehittämiseen. Muutoksista organisaation rakenteissa sekä yrityksen prosesseissa on tullut yleisiä toimenpiteitä. Yksi näkyvimmistä toiminnallisista uudistuksesta on ollut toiminnanohjausjärjestelmän käyttöönotto. Toiminnanohjausjärjestelmän rakenne ja kehitys aiheuttaa yleensä suurimmat vaikeudet pyrittäessä rakentamaan liiketoimintaprosessien läpinäkyvyyttä esittävä tietojärjestelmäympäristö. Tässä tutkimuksessa liiketoiminnan sekä toiminnanohjausjärjestelmän prosessien yhdistäminen on tehty ns. toiminnanohjausjärjestelmä muutostyökaluilla. Kyseiset muutostyökalut on järjestetty yrityksissä tietojärjestelmä ympäristöön ja niiden avulla voidaan korjata teknisiä ongelmia sekä muuttaa itse prosesseja. Tutkimuksen empiria osuudessa on käytetty case-tutkimusmenetelmää Kone Oyj:n prosessien kehittämisosastolla. Tutkimuksen tavoitteena oli parantaa toiminnanohjausjärjestelmän muutostyökalujen prosesseja, liiketoimintaprosessien sekä toiminnanohjausjärjestelmän yhdistämiseksi ja harmonisoimiseksi. Tutkimuksen tavoitteiden täyttämiseksi, prosessijohtamisen käsitteitä käytettiin muutostyökaluprosessien parannusehdotusten löytymiseksi. Prosessijohtamisen käsitteet tarkoittavat prosessikartan, prosessin toimintojen, sekä prosessin kustannusten tutkimista ja hyväksikäyttöä. Prosessijohtamisen käsitteeseen kuuluu myös liiketoimintaprosessien jatkuvan parantamisen sekä uudelleenjärjestämisen mallien kuvaus. Toiminnanohjausjärjestelmäympäristön kuvaus teorian toisena osuutena antaa pohjaa muutostyökalujen prosessien käytölle. Tutkimuksen tuloksina voidaan todeta että tutkimusalue on hyvin monimutkainen ja vaikea. Toimintajärjestelmistä ei ole kirjoitettu teoriaa kovinkaan runsaasti, lukuunottamatta yritysten itse tekemiä tutkimuksia. Tutkimuksessa tarkasteltaville prosesseille löytyi kuitenkin parannusehdotuksia sekä ns. optimaalisen prosessimallin ominaisuuksia.

Developing a user-centric event management system

This thesis describes the development of a software requirements specification for a user-centric event management system. The system is set to satisfy three goals: adding value for the event attendees, adding value for the event organizer, and reducing the costs of arranging and running an event. The requirements are identified by researching the prescriptive traits of event business and the current state of the case company and its environment. First the professional and human needs for events are scrutinized. Second, some recent reports about the current trends in the event business are reviewed. Then the event life cycle is presented using the model of new service development, and online promotion of events and especially word-of-mouth marketing receive special attention. Events are also regarded from the perspective of social networks and social media. The case company’s current state and its competitors are reviewed to formulate the needs which the system should fulfil. Then the currently available solutions for social media oriented event management are reviewed. The result is a set of functional and non-functional requirements. The functional requirements are categorized into social media, social networking, event personalization, event management, and system administration features. The specified features and non-functional requirements satisfy the three goals set for the system.

Problems of the architecture design in the system integration

This thesis studies the problems and their reasons a software architect faces in his work. The purpose of the study is to search and identify potential factors causing problens in system integration and software engineering. Under a special interest are non-technical factors causing different kinds of problems. Thesis was executed by interviewing professionals that took part in e-commerce project in some corporation. Interviewed professionals consisted of architects from technical implementation projects, corporation's architect team leader, different kind of project managers and CRM manager. A specific theme list was used as an guidance of the interviews. Recorded interviews were transcribed and then classified using ATLAS.ti software. Basics of e-commerce, software engineering and system integration is described too. Differences between e-commerce and e-business as well as traditional business are represented as are basic types of e-commerce. Software's life span, general problems of software engineering and software design are covered concerning software engineering. In addition, general problems of the system integration and the special requirements set by e-commerce are described in the thesis. In the ending there is a part where the problems founded in study are described and some areas of software engineering where some development could be done so that same kind of problems could be avoided in the future.

Non-Linear Journal Bearing Model for Analysis of Superharmonic Vibrations of Rotor Systems

A rotating machine usually consists of a rotor and bearings that supports it. The nonidealities in these components may excite vibration of the rotating system. The uncontrolled vibrations may lead to excessive wearing of the components of the rotating machine or reduce the process quality. Vibrations may be harmful even when amplitudes are seemingly low, as is usually the case in superharmonic vibration that takes place below the first critical speed of the rotating machine. Superharmonic vibration is excited when the rotational velocity of the machine is a fraction of the natural frequency of the system. In such a situation, a part of the machine’s rotational energy is transformed into vibration energy. The amount of vibration energy should be minimised in the design of rotating machines. The superharmonic vibration phenomena can be studied by analysing the coupled rotor-bearing system employing a multibody simulation approach. This research is focused on the modelling of hydrodynamic journal bearings and rotorbearing systems supported by journal bearings. In particular, the non-idealities affecting the rotor-bearing system and their effect on the superharmonic vibration of the rotating system are analysed. A comparison of computationally efficient journal bearing models is carried out in order to validate one model for further development. The selected bearing model is improved in order to take the waviness of the shaft journal into account. The improved model is implemented and analyzed in a multibody simulation code. A rotor-bearing system that consists of a flexible tube roll, two journal bearings and a supporting structure is analysed employing the multibody simulation technique. The modelled non-idealities are the shell thickness variation in the tube roll and the waviness of the shaft journal in the bearing assembly. Both modelled non-idealities may cause subharmonic resonance in the system. In multibody simulation, the coupled effect of the non-idealities can be captured in the analysis. Additionally one non-ideality is presented that does not excite the vibrations itself but affects the response of the rotorbearing system, namely the waviness of the bearing bushing which is the non-rotating part of the bearing system. The modelled system is verified with measurements performed on a test rig. In the measurements the waviness of bearing bushing was not measured and therefore it’s affect on the response was not verified. In conclusion, the selected modelling approach is an appropriate method when analysing the response of the rotor-bearing system. When comparing the simulated results to the measured ones, the overall agreement between the results is concluded to be good.