Defects in Persistent Luminescence Materials

Persistent luminescence materials can store energy from solar radiation or artificial lighting and release it over a period of several hours without a continuous excitation source. These materials are widely used to improve human safety in emergency and traffic signalization. They can also be utilized in novel applications including solar cells, medical diagnostics, radiation detectors and structural damage sensors. The development of these materials is currently based on methods based on trial and error. The tailoring of new materials is also hindered by the lack of knowledge on the role of their intrinsic and extrinsic lattice defects in the appropriate mechanisms. The goal of this work was to clarify the persistent luminescence mechanisms by combining ab initio density functional theory (DFT) calculations with selected experimental methods. The DFT approach enables a full control of both the nature of the defects and their locations in the host lattice. The materials studied in the present work, the distrontium magnesium disilicate (Sr₂MgSi₂O₇) and strontium aluminate (SrAl₂O₄) are among the most efficient persistent luminescence hosts when doped with divalent europium Eu²⁺ and co-doped with trivalent rare earth ions R³⁺ (R: Y, La-Nd, Sm, Gd-Lu). The polycrystalline materials were prepared with the solid state method and their structural and phase purity was confirmed by X-ray powder diffraction. Their local crystal structure was studied by high-resolution transmission electron microscopy. The crystal and electronic structure of the nondoped as well as Eu²⁺, R^2+/3+ and other defect containing materials were studied using DFT calculations. The experimental trap depths were obtained using thermoluminescence (TL) spectroscopy. The emission and excitation of Sr₂MgSi₂O₇:Eu²+,Dy³⁺ were also studied. Significant modifications in the local crystal structure due to the Eu²⁺ ion and lattice defects were found by the experimental and DFT methods. The charge compensation effects induced by the R³⁺ co-doping further increased the number of defects and distortions in the host lattice. As for the electronic structure of Sr₂MgSi₂O₇ and SrAl₂O₄, the experimental band gap energy of the host materials was well reproduced by the calculations. The DFT calculated Eu²⁺ and R^2+/3+ 4fn as well as 4f^n-15d¹ ground states in the Sr₂MgSi₂O₇ band structure provide an independent verification for an empirical model which is constructed using rather sparse experimental data for the R³⁺ and especially the R²⁺ ions. The intrinsic and defect induced electron traps were found to act together as energy storage sites contributing to the materials’ efficient persistent luminescence. The calculated trap energy range agreed with the trap structure of Sr₂MgSi₂O₇ obtained using TL measurements. More experimental studies should be carried out for SrAl₂O₄ to compare with the DFT calculations. The calculated and experimental results show that the electron traps created by both the rare earth ions and vacancies are modified due to the defect aggregation and charge compensation effects. The relationships between this modification and the energy storage properties of the solid state materials are discussed.

NIR-Vis Up-Conversion Luminescence in the Yb3+,Er3+ Doped Y2O2S, ZrO2, and NaYF4 Nanomaterials

Since the discovery of the up-conversion phenomenon, there has been an ever increasing interest in up-converting phosphors in which the absorption of two or more low energy photons is followed by emission of a higher energy photon. Most up-conversion luminescence materials operate by using a combination of a trivalent rare earth (lanthanide) sensitizer (e.g. Yb or Er) and an activator (e.g. Er, Ho, Tm or Pr) ion in a crystal lattice. Up-converting phosphors have a variety of potential applications as lasers and displays as well as inks for security printing (e.g. bank notes and bonds). One of the most sophisticated applications of lanthanide up-conversion luminescence is probably in medical diagnostics. However, there are some major problems in the use of photoluminescence based on the direct UV excitation in immunoassays. Human blood absorbs strongly UV radiation as well as the emission of the phosphor in the visible. A promising way to overcome the problems arising from the blood absorption is to use a long wavelength excitation and benefit from the up-conversion luminescence. Since there is practically no absorption by the whole-blood in the near IR region, it has no capability for up-conversion in the excitation wavelength region of the conventional up-converting phosphor based on the Yb3+ (sensitizer) and Er3+ (activator) combination. The aim of this work was to prepare nanocrystalline materials with high red (and green) up-conversion luminescence efficiency for use in quantitative whole-blood immunoassays. For coupling to biological compounds, nanometer-sized (crystallite size below 50 nm) up-converting phosphor particles are required. The nanocrystalline ZrO2:Yb3+,Er3+, Y2O2S:Yb3+,Er3+, NaYF4:Yb3+,Er3+ and NaRF4-NaR’F4 (R: Y, Yb, Er) materials, prepared with the combustion, sol-gel, flux, co-precipitation and solvothermal synthesis, were studied using the thermal analysis, FT-IR spectroscopy, transmission electron microscopy, EDX spectroscopy, XANES/EXAFS measurements, absorption spectroscopy, X-ray powder diffraction, as well as up-conversion and thermoluminescence spectroscopies. The effect of the impurities of the phosphors, crystallite size, as well as the crystal structure on the up-conversion luminescence intensity was analyzed. Finally, a new phenomenon, persistent up-conversion luminescence was introduced and discussed. For efficient use in bioassays, more work is needed to yield nanomaterials with smaller and more uniform crystallite sizes. Surface modifications need to be studied to improve the dispersion in water. On the other hand, further work must be carried out to optimize the persistent up-conversion luminescence of the nanomaterials to allow for their use as efficient immunoassay nanomaterials combining the advantages of both up-conversion and persistent luminescence.

New Product Development (NPD) Success Factors: A Review of the Literature

This paper reviews the literature on managerially actionable new product development success factors and summarises the field in a classic managerial framework. Because of the varying quality, breadth and scope of the field, the review only contains post-1980 studies of tangible product development that are of a rigorous scientific standard. Success is interpreted as a commercial success. The field has gained insight into a broad set of factors that vary in scope, abstraction and context. Main areas that contribute to NPD success are top management support exhibited through resource allocation and communicating the strategic importance of NPD in the organisation. The right projects need to be selected for investment at the beginning of the process and should be aligned to the organisation's internal competencies and the external environment. The NPD process should use cross-functional teams and a competent project champions. Marketing research competency is crucial, as an understanding of the market, customers and competitors is repeatedly highlighted. Product launch competency was also consistently shown to be important. In terms of controlling the NPD process, strict project gates are required to maintain control.

Particle Size Analysis of Pharmaceutical Powders by Laser Diffraction

Raaka-aineen hiukkaskoko on lääkekehityksessä keskeinen materiaaliparametri. Lääkeaineen partikkelikoko vaikuttaa moneen lääketuotteen tärkeään ominaisuuteen, esimerkiksi lääkkeen biologiseen hyväksikäytettävyyteen. Tässä diplomityössä keskityttiin jauhemaisten lääkeaineiden hiukkaskoon määrittämiseen laserdiffraktiomenetelmällä. Menetelmä perustuu siihen, että partikkeleista sironneen valon intensiteetin sirontakulmajakauma on riippuvainen partikkelien kokojakaumasta. Työn kirjallisuusosassa esiteltiin laserdiffraktiomenetelmän teoriaa. PIDS (Polarization Intensity Differential Scattering) tekniikka, jota voidaan käyttää laserdiffraktion yhteydessä, on myös kuvattu kirjallisuusosassa. Muihin menetelmiin perustuvista analyysimenetelmistä tutustuttiin mikroskopiaan sekä aerodynaamisen lentoajan määrittämiseen perustuvaan menetelmään. Kirjallisuusosassa esiteltiin myös partikkelikoon yleisimpiä esitystapoja. Työn kokeellisen osan tarkoituksena oli kehittää ja validoida laserdiffraktioon perustuva partikkelikoon määritysmenetelmä tietylle lääkeaineelle. Menetelmäkehitys tehtiin käyttäen Beckman Coulter LS 13 320 laserdiffraktoria. Laite mahdollistaa PIDS-tekniikan käytön laserdiffraktiotekniikan ohella. Menetelmäkehitys aloitettiin arvioimalla, että kyseinen lääkeaine soveltuu parhaiten määritettäväksi nesteeseen dispergoituna. Liukoisuuden perusteella väliaineeksi valittiin tällä lääkeaineella kyllästetty vesiliuos. Dispergointiaineen sekä ultraäänihauteen käyttö havaittiin tarpeelliseksi dispergoidessa kyseistä lääkeainetta kylläiseen vesiliuokseen. Lopuksi sekoitusnopeus näytteensyöttöyksikössä säädettiin sopivaksi. Validointivaiheessa kehitetyn menetelmän todettiin soveltuvan hyvin kyseiselle lääkeaineelle ja tulosten todettiin olevan oikeellisia sekä toistettavia. Menetelmä ei myöskään ollut herkkä pienille häiriöille.

Segregation of powder mixtures in silos with particular reference to dry mineral-based construction materials

Segregering eller segregation är ett fenomen som kan förekomma inom olika områden av samhället. Inom samhällsvetenskaperna kan segregering definieras som det rumsliga åtskiljandet av befolkningsgrupper på urval av ras eller etniskt ursprung, kön, social härkomst, religion, ålder, yrke, osv. Segregering av befolkningsgrupper sker ofta mer eller mindre frivilligt och är motsatsen till integration. Inom partikelteknologi definieras segregering oftast som det rumsliga åtskiljandet av beståndsdelarna i en blandning av olika partiklar. Segregering sker då på urval av bl.a. partiklarnas storlek, densitet, form, elektrostatiska eller mekaniska egenskaper, och kan beskrivas som motsatsen till blandning. Segregeringsmekanismer används för att förklara hur och varför en partikelblandning segregerar samt vad slutresultatet i form av den rumsliga fördelningen av partiklarna blir till följd av att blandningen utsetts för en viss behandling. I denna avhandling har segregering av partikelblandningar och speciellt torra mineralbaserade byggmaterial (t.ex. murbruk) till följd av lagring i siloer studerats. Vid industriell produktion av mineralbaserade byggmaterial används siloer för korttidslagring av slutprodukterna precis innan förpackning. Segregering leder till kraftiga variationer i sammansättningen för partikelströmmen ut ur silon, vilket gör att slutprodukterna inte uppfyller kvalitetskraven och kan därmed inte säljas till kunder. Detta leder till arbetsam och dyr bearbetning (återcirkulation) av produkterna med påföljder för produktionsekonomin samt hållbara utvecklingen. I avhandlingen identifierades de väsentligaste segregeringsmekanismerna för torra mineralbaserade byggmaterial i siloer. Dessutom klargjordes effekterna av materialegenskaper, processbetingelser och siloparametrar. Slutligen behandlas möjliga åtgärder för minskning av partikelsegregering i siloer samt tillämpning av matematiska metoder för simulering av partikelflöden med hjälp av datorer.

Pulsed electric field assisted sol-gel preparation of TiO2 particles and their photocatalytic properties

The objective of this thesis was to study the effect of pulsed electric field on the preparation of TiO2 nanoparticles via sol-gel method. The literature part deals with properties of different TiO2 crystal forms, principles of photocatalysis, sol-gel method and pulsed electric field processing. It was expected that the pulsed electric field would have an influence on crystallite size, specific surface area, polymorphism and photocatalytic activity of produced particles. TiO2 samples were prepared by using different frequencies and treatment times of pulsed electric field. The properties of produced TiO2 particles were examined X-ray diffraction (XRD), Raman spectroscopy and BET surface area analysis. The photocatalytic activities of produced TiO2 particles were determined by using them as photocatalysts for the degradation of formic acid under UVA-light. The photocatalytic activities of samples produced with sol-gel method were also compared with the commercial TiO2 powder Aeroxide® (Evonic Degussa GmbH). Pulsed electric field did not have an effect on the morphology of particles. Results from XRD and Raman analysis showed that all produced TiO2 samples were pure anatase. However, pulsed electric field did have an effect on crystallite size, specific surface area and photocatalytic activity of TiO2 particles. Generally, the crystallite sizes were smaller, specific surface areas larger and initial formic acid degradation rates higher for samples that were produced by applying the pulsed electric field. The higher photocatalytic activities were attributed to larger surface areas and smaller crystallite sizes. Though, with all of the TiO2 samples produced by the sol-gel method the initial formic acid degradation rates were significantly slower than with the commercial TiO2 powder.

Influence of Pulsed-Electric Field Irradiation in Crystallization

The growing pharmaceutical interest, among others, in the polymorphic composition of the emerging solid end-products from production processes has been traced to the need for attainment of high product purity. This is more so as the presence of different polymorphs may constitute physical impurity of the product. Hence, the need for optimization of the yield of desired product component(s) through controlled crystallization kinetics for instance. This study was carried out to investigate the impact of pulsed electric field (PEF) irradiation on the crystal morphology of glycine obtained by cooling crystallization (without seeding) from commercial glycine sample in distilled deionized water solution. In doing so, three different pulse frequencies (294, 950 and 145 Hz) and a case without PEF were studied at three cooling rates (5, 10 and 20 ºC/h). The crystal products obtained were analyzed for polymorphic composition by powder x-ray diffraction (PXRD) and Fourier transform infrared (FTIR) spectroscopy while the particles characterization was done on Morphologi G3. The results obtained from this study showed that pulsed electric field irradiation had significant impact on metastability of the aqueous solution as well as on the polymorphic composition of the end product. With increasing PEF frequency applied, nucleation started earlier and the γ-glycine polymorph content of the product crystals increased. These were found to have been aided by cooling rate, as the most significant effect was observed at 5 ºC/h. It was also discovered that PEF application had no measurable impact on the pH of the aqueous solution as well as the size distribution of the particles. Cooling on the contrary was believed to be responsible for the broadening of the particle size distribution with a downward shift of the lower limit of the raw material from about 100 μm to between 10 and 50 μm.

Energy and raw material consumption analysis of powder bed fusion: case study: CNC machining and laser additive manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, is a powder bed fusion (PBF) type of additive manufacturing (AM) technology used to manufacture metal parts layer by layer by assist of laser beam. The development of the technology from building just prototype parts to functional parts is due to design flexibility. And also possibility to manufacture tailored and optimised components in terms of performance and strength to weight ratio of final parts. The study of energy and raw material consumption in LAM is essential as it might facilitate the adoption and usage of the technique in manufacturing industries. The objective this thesis was find the impact of LAM on environmental and economic aspects and to conduct life cycle inventory of CNC machining and LAM in terms of energy and raw material consumption at production phases. Literature overview in this thesis include sustainability issues in manufacturing industries with focus on environmental and economic aspects. Also life cycle assessment and its applicability in manufacturing industry were studied. UPLCI-CO2PE! Initiative was identified as mostly applied exiting methodology to conduct LCI analysis in discrete manufacturing process like LAM. Many of the reviewed literature had focused to PBF of polymeric material and only few had considered metallic materials. The studies that had included metallic materials had only measured input and output energy or materials of the process and compared to different AM systems without comparing to any competitive process. Neither did any include effect of process variation when building metallic parts with LAM. Experimental testing were carried out to make dissimilar samples with CNC machining and LAM in this thesis. Test samples were designed to include part complexity and weight reductions. PUMA 2500Y lathe machine was used in the CNC machining whereas a modified research machine representing EOSINT M-series was used for the LAM. The raw material used for making the test pieces were stainless steel 316L bar (CNC machined parts) and stainless steel 316L powder (LAM built parts). An analysis of power, time, and the energy consumed in each of the manufacturing processes on production phase showed that LAM utilises more energy than CNC machining. The high energy consumption was as result of duration of production. Energy consumption profiles in CNC machining showed fluctuations with high and low power ranges. LAM energy usage within specific mode (standby, heating, process, sawing) remained relatively constant through the production. CNC machining was limited in terms of manufacturing freedom as it was not possible to manufacture all the designed sample by machining. And the one which was possible was aided with large amount of material removed as waste. Planning phase in LAM was shorter than in CNC machining as the latter required many preparation steps. Specific energy consumption (SEC) were estimated in LAM based on the practical results and assumed platform utilisation. The estimated platform utilisation showed SEC could reduce when more parts were placed in one build than it was in with the empirical results in this thesis (six parts).

Metal additive manufacturing of internal flow channels with powder bed fusion processes

This thesis studies the advantages, disadvantages and possibilities of additive manufacturing in making components with internal flow channels. These include hydraulic components, components with cooling channels and heat exchangers. Processes studied in this work are selective laser sintering and selective laser melting of metallic materials. The basic principles of processes and parameters involved in the process are presented and different possibilities of internal channel manufacturing and flow improvement are introduced

Haihdutusnopeuksien määritys glysiinin alipainekiteytyksessä

Alipainekiteytyksessä tasalaatuisen lopputuotteen valmistamiseksi kiteytysolosuhteiden vaikutus liuottimen haihtumisvuohon ja kiteiden ominaisuuksiin on huomioitava. Kandidaatin työn tavoitteena oli selvittää, miten glysiinin alipainekiteytyksessä vesiliuoksesta kiteytysolosuhteet (lämpötila ja paine) vaikuttavat liuottimen haihtumisvuohon ja syntyvien kiteiden polymorfiaan. Haihdutuskokeet suoritettiin puhtaalle vedelle ja alipainekiteytyskokeet glysiinin 95 % kylläiselle vesiliuokselle lämpötiloissa 40 °C, 50 °C ja 60 °C ja paineissa 40 mbar, 60 mbar ja 80 mbar. Kiteyttimenä käytettiin suljettua, virtaushaitoilla, sekoittimella ja ohjausputkella varustettua reaktoria johon oli kytketty alipainepumppu ja termostaatti paineen ja lämpötilan ohjaamiseksi. Nesteen määrä haihdutuskokeissa oli 2 kg ja alipainekiteytyskokeissa 1,2 kg. Osa alipainekiteytyskokeista saaduista kiteistä analysoitiin jauheröntgendiffraktioanalysaattorin (PXRD, engl. powder x-ray diffraction) avulla. Kaikki PXRD-laitteella analysoidut alipainekiteytyskokeissa saadut kiteet osoittautuivat glysiinin γ-polymorfiksi. Kiteytysolosuhteilla oli selkeä vaikutus haihtumisvuohon, mutta vaikutusta glysiinikiteiden polymorfiaan ei havaittu koealueella.

Weldability of powder bed fusion fabricated stainless steel 316L sheets to cold rolled sheet metal

Weldability of powder bed fusion (PBF) fabricated components has come to discussion in past two years due to resent developments in the PBF technology and limited size of the machines used in the fabrication process. This study concentrated on effects of energy input of welding on mechanical properties and microstructural features of welds between PBF fabricated stainless steel 316L sheets and cold rolled sheet metal of same composition by the means of destructive testing and microscopic analysis. Optical fiber diameter, laser power and welding speed were varied during the experiments that were executed following one variable at a time (OVAT) method. One of the problems of welded PBF fabricated components has been lower elongations at break comparing to conventionally manufactured components. Decreasing energy input of the laser keyhole welding decreased elongations at break of the welded specimens. Ultimate tensile strengths were not affected significantly by the energy input of the welding, but fracturing of the specimens welded using high energy input occurred from the weld metal. Fracturing of the lower energy input welds occurred from the PBF fabricated base metal. Energy input was found to be critical factor for mechanical properties of the welds. Multioriented grain growth and formation of neck at fusion zone boundary on the cold rolled side of the weld was detected and suspected to be result from weld pool flows caused by differences in molten weld pool behaviour between the PBF fabricated and cold rolled sides of the welds.