Koivun HFV-kuivauksen kustannusvaikutukset

Työn tavoitteena on ollut selvittää HFV-kuivauksen taloudellisia vaikutuksia, kuivausmenetelmän toimintaperiaatteita, ominaisuuksia ja Lahden ammattikorkeakoulun Tekniikan laitoksen kuivaustutkimuksesta saatuja tuloksia. Tutkimuskohteeksi on valittu sydänkeskeinen koivu, joka soveltuu erinomaisesti uuden kuivausmenetelmän raaka-aineeksi, sillä sen hankintakustannukset muodostuvat tavanomaista koivusahatavaraa alhaisemmaksi ja sillä saavutetaan raaka-aineen jatkojalostusarvon huomattava nousu. Työn teoriaosassa on käsitelty puun kuivausta, sen yleisiä piirteitä ja erikuivausvaihtoehtoja. Koivun kuivauksesta ja kuivauskustannuksista löytyy varsinvähän julkaistua tutkimustietoa, jonka johdosta kuivauskustannuksia kartoitettiin myös kotimaisten havupuiden osalta. Tuoreen koivun kuivaus muutamassa tunnissa puusepänkuivaksi aihioksi ilman kuivausvirheitä on Lahden ammattikorkeakoulun Tekniikan laitoksen tutkimuksissa saatujen tuloksien mukaan mahdollista. Tässä tutkimuksessa on käsitelty neljän eri teholuokan kuivaamoinvestointivaihtoehtoa. Vaihtoehdot poikkeavat toisistaan niin hankintahinnan, tuotantokapasiteetin kuinvalmistuskustannuksienkin suhteen. Mikäli kuivaamon tuotantokapasiteetti ei olemääräävä tekijä ja investoinnilla ei ole pääomarajoitetta, niin kannattavimmaksi investointivaihtoehdoksi osoittautuu suurimman kokoluokan HFV-kuivaamolaitteisto.

Fibre-reinforced composites as root canal posts

Fibre-reinforced composite (FRC) root canal posts are suggested to have biomechanical benefits over traditional metallic posts, but they lack good adhesion to resin composites. The aim of this series of studies was to evaluate the adhesion of individually formed fibre-reinforced composite material to composite resin and dentin, as well as some mechanical properties. Flexural properties were evaluated and compared between individually formed FRC post material and different prefabricated posts. The depth of polymerization of the individually formed FRC post material was evaluated with IR spectrophotometry and microhardness measurements, and compared to that of resin without fibres. Bonding properties of the individually formed FRC post to resin cements and dentin were tested using Pull-out- and Push-out-force tests, evaluated with scanning electron microscopy, and compared to those of prefabricated FRC and metal posts. Load-bearing capacity and microstrain were evaluated and failure mode assessment was made on incisors restored with individually formed FRC posts of different structures and prefabricated posts. The results of these studies show that the individually polymerized and formed FRC post material had higher flexural properties compared to the commercial prefabricated FRC posts. The individually polymerized FRC material showed almost the same degree of conversion after light polymerization as monomer resin without fibres. Moreover, it was found that the individually formed FRC post material with a semiinterpenetrating polymer network (IPN) polymer matrix bonded better to composite resin luting cement, than did the prefabricated posts with a cross-linked polymer matrix. Furthermore, it was found that, contrary to the other posts, there were no adhesive failures between the individually formed FRC posts and composite resin luting cement. This suggests better interfacial adhesion of cements to these posts. Although no differences in load-bearing capacity or microstrain could be seen, the incisors restored with individually formed FRC posts with a hollow structure showed more favourable failures compared to other prefabricated posts. These studies suggest that it is possible to use individually formed FRC material with semi-IPN polymer matrix as root canal post material. They also indicate that there are benefits especially regarding the bonding properties to composite resin and dentin with this material compared to prefabricated FRC post material with a cross-linked matrix. Furthermore, clinically more repairable failures were found with this material compared to those of prefabricated posts.

Radiative Heat Transfer in Boiler Furnaces

Better models are needed for radiative heat transfer in boiler furnaces. If the process is known better, combustion in the furnace can be optimized to produce low emissions. It makes the process to be environmental friendly. Furthermore, if there is a better model of the furnace it can more fully explain what is happening inside the furnace. Using of the model one can quickly and easily analyze how it operates with bio fuels, moist fuels or difficult fuels and improve the operation. Models helps with better estimation of furnace dimensions and result in more accurate understanding of operation. Key component lacking in these models is radiative heat transfer in particle laden gases. If there are no particles than radiative heat transfer can be calculated approximately. There are two problems with current models when used with flow modeling. The first one is a need to account for a particle laden gas and the second one is an absence of a fast algorithm. Fast calculation is needed if radiative heat transfer calculation is done for a large CDF model. Computations slow down if time is required for calculating radiative properties over and over again. This thesis presents a band model for radiative heat transfer in boiler furnaces. Advantage is a quickness of calculation and account of particles in the process.

Metsäpolttoaineiden vesitiekuljetus proomukalustolla

Metsäpolttoaineiden käyttö kasvaa lämpö- ja voimalaitoksissa ja mahdollisissa biojalostamoissa. Metsäpolttoaineilla voidaan saavuttaa päästövähennyksiä korvaamalla päästöintensiivisempiä polttoaineita. Metsäpolttoaineen kysynnän kasvu suurkäyttöpaikoilla luo uusia vaatimuksia metsäbiomassan hankintaan. Metsäpolttoaineiden vesitiekuljetuksen sisältämiä logistiikkajärjestelmiä kehittämällä toimitusvarmuutta pystytään parantamaan ja hankintaa laajentamaan kustannustehokkaasti ja ympäristöystävällisesti. Kuljetuskokeilut antoivat uutta tietoa vesitiekuljetuksen sisältämästä hankinnasta. Lastikapasiteetti nykyisen kaltaisessa Eurooppa IIa -suurproomussa vaihtelee 1200 tonnista jopa 1800 tonniin (kosteus 40 %) riippuen tiivistymisestä ja proomun modifiointiasteesta. Metsähakkeen energiatiheys oli suurproomukuljetuksissa keskimäärin 1 MWh/i-m3, joka oli 25 % parempi kuin vertailun hakerekkakuljetuksissa. Vesitiekuljetuksen kustannukset olivat kuljetuskokeiluissa lastauksineen ja purkuineen 0,02 €/MWh/km, ollen noin 20 % ketjun kokonaiskustannuksista. Simuloinnin edullisimpien vesitiekuljetusvaihtoehtojen vaihteluvälin kustannukset olivat vastaavasti 0,013 - 0,026 €/MWh/km. Lastauksen ja purun kustannus oli 0,4 - 0,6 €/MWh ja vesitiekuljetus 0,9 - 2,0 €/MWh (100 km). Ketjun kokonaiskustannukset hakkuutähdehakkeelle vaihtelivat simuloinnin edullisimpien vaihtoehtojen perusteella välillä 10,8 - 12,1 €/MWh (30 km rekka, 100 km proomu). Kuljetusketjujen simuloinnin kustannukset osoittivat proomukuljetusketjun olevan kilpailukykyinen vaihtoehto hakerekkakuljetusketjulle kalustosta ja vuosittaisista käyttötunneista riippuen kuljetusetäisyyden ylittäessä 100 km. Kustannustehokkain ratkaisu vesitiekuljetuksessa saavutettiin pienen aluksen ja suuren kokoluokan proomuyksikön kytkyeellä. Haketus kannattaa toteuttaa ennen proomukuljetuksen osuutta metsähakkeen paremman tiiviyden ja käsiteltävyyden perusteella. Logistiikkajärjestelmiä pitää kehittää tapauskohtaisesti käyttöpaikan tarpeet ja olosuhteet huomioon ottaen. Metsäpolttoaineiden vesitiekuljetuksen sisältämän logistiikan liiketoimintamallien vertailussa arvioitiin vaihtoehtoiset ulkoistetut toimintamallit paremmaksi kuin nykyinen urakointimalli. Tämä mahdollistaa paremman metsähakkeen saatavuuden ja logistiikan tehokkuuden lastausterminaaleissa. Terminaalitoiminnot ja proomukuljetukset lisäävät uusia liiketoimintamahdollisuuksia ja mahdollistavat metsäpolttoaineiden

Rigid Rod Polymer Fillers in Acrylic Denture and Dental Adhesive Resin Systems

Polymeric materials have been used in dental applications for decades. Adhesion of polymeric materials to each other and to the tooth substrate is essential to their successful use. The aim of this series of studies was two-folded. First, to improve adhesion of poly(paraphenylene) based rigid rod polymer (RRP) to other dental polymers, and secondly, to evaluate the usability of a new dentin primer system based on RRP fillers. Poly(paraphenylene) based RRP would be a tempting material for dental applications because of its good mechanical properties. To be used in dental applications, reliable adhesion between RRP and other dental polymers is required. In this series of studies, the adhesion of RRP to denture base polymer and the mechanical properties of RRP-denture base polymer-material combination were evaluated. Also adhesion of BisGMA-TEGDMA-resin to RRP was determined. Different surface treatments were tested to improve the adhesion of BisGMA-TEGDMA-resin to RRP. Results were based on three-point bending testing, Vickers surface hardness test and scanning electron microscope analysis (SEM), which showed that no reliable adhesion between RRP and denture base polymer was formed. Addition of RRP filler to denture base polymer increased surface hardness and flexural modulus but flexural strength decreased. Results from the shear bond strength test and SEM revealed that adhesion between resin and RRP was possible to improve by surface treatment with dichloromethane (DCM) based primer and a new kind of adhesive surface can be designed. The current dentin bonding agents have good immediate bond strength, but in long term the bond strength may decrease due to the detrimental effect of water and perhaps by matrix metalloproteinases. This leads to problems in longevity of restorations. Current bonding agents use organic monomers. In this series of studies, RRP filled dentin primer was tested in order to decrease the water sorption of the monomer system of the primers. The properties of new dentin primer system were evaluated in vitro by comparing it to commercial etch and rinse adhesive system. The results from the contact angle measurements and SEM showed that experimental primer with RRP reinforcement provided similar resin infiltration to dentin collagen and formed the resin-dentin interface as the control primer. Microtensile bond strength test and SEM revealed that in short term water storing, RRP increased bond strength and primer with BMEP-monomer (bis[2-(methacryloyloxy)-ethyl]phosphate) and high solvent concentration provided comparable bonding properties to the commercial control primers. In long term water storing, the high solvent-monomer concentration of the experimental primers decreased bond strength. However, in low solvent-monomer concentration groups, the long-term water storing did not decrease the bond strength despite the existence of hydrophilic monomers which were used in the system. These studies demonstrated that new dentin primer system reached the mechanical properties of current traditional etch and rinse adhesive system in short time water storing. Improved properties can be achieved by further modifications of the monomer system. Studies of the adhesion of RRP to other polymers suggest that adhesion between RRP and other dental polymers is possible to obtain by certain surface treatments.

Theorica Pantegni . Facsimile and Transcription of the Helsinki manuscript (Codex EÖ.II.14)

The Theorica Pantegni is a medieval medical textbook written in Latin. The author was Constantine the African (Constantinus Africanus), a monk of Tunisian origin. He compiled the work in the latter half of the eleventh century at the Benedictine monastery of Monte Cassino in Italy. - Manuscript Eö.II.14, containing the Theorica Pantegni published here, belongs today to the National Library of Finland. It can be dated to the third quarter of the twelfth century, which makes it one of the earliest surviving exemplars of the Theorica Pantegni: over seventy manuscripts of the work survive, of which about fifteen can be dated to the twelfth century. Manuscript Eö.II.14 is written in black ink on 210 parchment leaves (recto and verso), amounting to 420 pages, in pre-Gothic script. - The present text is a transcription of Ms Eö.II.14. The goal is to provide the reader with an accessible text that is faithful to the original.

Structural and operational optimisation : applications in energy systems

In this work mathematical programming models for structural and operational optimisation of energy systems are developed and applied to a selection of energy technology problems. The studied cases are taken from industrial processes and from large regional energy distribution systems. The models are based on Mixed Integer Linear Programming (MILP), Mixed Integer Non-Linear Programming (MINLP) and on a hybrid approach of a combination of Non-Linear Programming (NLP) and Genetic Algorithms (GA). The optimisation of the structure and operation of energy systems in urban regions is treated in the work. Firstly, distributed energy systems (DES) with different energy conversion units and annual variations of consumer heating and electricity demands are considered. Secondly, district cooling systems (DCS) with cooling demands for a large number of consumers are studied, with respect to a long term planning perspective regarding to given predictions of the consumer cooling demand development in a region. The work comprises also the development of applications for heat recovery systems (HRS), where paper machine dryer section HRS is taken as an illustrative example. The heat sources in these systems are moist air streams. Models are developed for different types of equipment price functions. The approach is based on partitioning of the overall temperature range of the system into a number of temperature intervals in order to take into account the strong nonlinearities due to condensation in the heat recovery exchangers. The influence of parameter variations on the solutions of heat recovery systems is analysed firstly by varying cost factors and secondly by varying process parameters. Point-optimal solutions by a fixed parameter approach are compared to robust solutions with given parameter variation ranges. In the work enhanced utilisation of excess heat in heat recovery systems with impingement drying, electricity generation with low grade excess heat and the use of absorption heat transformers to elevate a stream temperature above the excess heat temperature are also studied.

Taxonomy, species richness and biogeography of Finnish crane flies (Diptera, Tipuloidea).

Biodiversity is unequally spread throughout terrestrial ecosystems. The highest species richness of animals and plants is encountered around the Equator, and naturalists observe a decrease in the number of creatures with increasing latitude. Some animal groups, however, display an anomalous species richness pattern, but these are exceptions to the general rule. Crane flies (Diptera, Tipuloidea) are small to large sized, non-biting nematoceran insects, being mainly associated with moist environments. The species richness of crane flies is highest in the tropics, but these insects are species rich and abundant in all biogeographic realms, boreal and arctic biomes included. The phylogeny and systematics of crane flies are still at an early stage and somewhat controversial. New species are constantly discovered even from temperate Europe, faunistically the best known continent. Crane flies have been rather neglected group of insects in Finland. The history of Finnish crane fly taxonomy and faunistics started in 1907, the year when Carl Lundström published his two first articles on tipuloids. Within roughly 100 years there have been only a handful of entomologists studying the Finnish fauna, and the species richness and natural history of these flies have remained poorly understood and mapped. The aim of this thesis is to clarify the taxonomy of Finnish crane flies, present an updated and annotated list of species and seek patterns in regional species richness and assemblage composition. Tipula stackelbergi Alexander has been revised (I). This species was elevated to a species rank from a subspecific rank under T. pruinosa Wiedemann and T. stackelbergi was also deleted from the list of European crane flies. Two new synonyms were found: T. subpruinosa Mannheims is a junior synonym of T. freyana Lackschewitz and T. usuriensis Alexander is a junior synonym of T. pruinosa. A new species Tipula recondita Pilipenko & Salmela has been described (II). Both morphology and COI (mtDNA) sequences were used in the assessment of the status of the species. The new species is highly disjunct, known from Finland and Russian Far East. A list of Finnish crane flies was presented, including the presence of species in the Finnish biogeographical provinces (III). A total of twenty-four species were formally reported for the first time from Finland and twenty-two previously reported species were deleted from the list. A short historical review on the studies of Finnish crane flies has been provided. The current list of Finnish species consists of 338 crane flies (IV, Appendix I). Species richness of all species and saproxylic/fungivorous species is negatively correlated with latitude, but mire-dwelling species show a reversed species richness gradient (i.e. an increase in the number of species toward north). Provincial assemblages displayed a strong latitudinal gradient and faunistic distance increased with increasing geographical distance apart of the provinces. Nearly half (48 %) of the Finnish crane flies are Trans-Palaearctic, roughly one-third (34 %) are West Palaearctic and only 16 and 2 % are Holarctic and Fennoscandian, respectively. Due to the legacy of Pleistocene glaciations, endemic Fennoscandian species are problematic and it is thus concluded that there are probably no true endemic crane flies in this region. Finally, there are probably species living within Finnish borders that have hitherto remained unnoticed. Based on subjective assessment, the number of “true” (i.e. recorded + unknown species) species count of Finnish crane flies is at minimum 350.

Hakkeen kuivaus ennen varastointia ja biopolttoaineterminaalin suunnittelu

Lempäälään aiotaan rakentaa uusi kaukolämpölaitos, jossa polttoaineena käytettäisiin haketta. Nykyään Lempäälässä tuotetaan kaukolämpöä maakaasulla, jonka käyttämisestä halutaan siirtyä käyttämään lähialueilta saatavaa biopolttoainetta. Tässä työssä halutaan selvittää, mitä hyötyjä saataisiin hakkeen koneellisesta kuivauksesta. Työn toisena tavoitteena on suunnitella ja pohtia biopolttoaineterminaalin rakentamista sekä käsitellä hakkeen varastointia yleensä. Työssä tutustutaan hakkeeseen aiheesta kertovan kirjallisuuden avulla. Työssä on myös laskettu hakkeen kuivauksesta saatavia hyötyjä hakkeen lämpöarvoon sekä energiatiheyteen. Erityisesti perehdytään metsätähdehakkeeseen, rankahakkeeseen, kuorihakkeeseen sekä sahanpuruun. Laskelmien tuloksista on havaittu, että suurin hyöty hakkeen energiatiheyden parantumisessa saadaan kun hake kuivataan 35 % kosteuspitoisuuteen. Tämän jälkeen energiatiheyden paraneminen tapahtuu hitaammin. Hakkeen kuivauksesta saadaan myös muita hyötyjä kuin energiatiheyden paraneminen. Kuivan hakkeen käsittelyn ja varastoinnin on havaittu olevan vaivattomampaa kuin märän hakkeen. Biopolttoaineterminaalin ja voimalaitoksen tulisi sijaita rinnakkain, jotta hakkeen kuivauksesta saadaan mahdollisimman kustannustehokasta. Näin ollen syntyisi myös säästöjä hakkeen kuljetuksen suhteen. Biopolttoaineterminaalin rakentamista varten tarvittaisiin tilaa alustavien laskelmien perusteella noin yksi hehtaari. Työssä on myös laskettu biopolttoaineterminaalin rakentamisesta aiheutuvia kustannuksia sekä hakkeen kuljetuksesta koituvia logistiikka kustannuksia. Haketerminaalin ja voimalaitoksen sijaintia Lempäälässä on myös kartoitettu.

Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.