Development of an environmentally friendly method of starch oxidation by hydrogen peroxide and a complex water-soluble Iron catalyst

Oxidized starch is a key component in the paper industry, where it is used as both surfacing sizer and filler. Large quantities are annually used for this purpose; however, the methods for the oxidation are not environmentally friendly. In our research, we have studied the possibility to replace the harmful oxidation agents, such as hypochlorite or iodates and transition metal catalysts, with a more environmentally friendly oxidant, hydrogen peroxide (H2O2), and a special metal complex catalyst (FePcS), of which only a small amount is needed. The work comprised batch and semi-batch studies by H2O2, ultrasound studies of starch particles, determination of low-molecular by-products and determination of the decomposition kinetics of H2O2 in the presence of starch and the catalyst. This resulted in a waste-free oxidation method, which only produces water and oxygen as side products. The starch oxidation was studied in both semi-batch and batch modes in respective to the oxidant (H2O2) addition. The semi-batch mode proved to yield a sufficient degree of substitution (COOH groups) for industrial purposes. Treatment of starch granules by ultrasound was found to improve the reactivity of starch. The kinetic results were found out to have a rather complex pattern – several oxidation phases were observed, apparently due to the fact that the oxidation reaction in the beginning only took place on the surface, whereas after a prolonged reaction time, partial degradation of the solid starch granules allowed further reaction in the interior parts. Batch-mode experiments enabled a more detailed study of the mechanisms of starch in the presence of H2O2 and the catalyst, but yielded less oxidized starch due to rapid decomposition of H2O2 due to its high concentrations. The effect of the solid-liquid (S/L) ratio in the reaction system was studied in batch experiments. These studies revealed that the presence of the catalyst and the starch enhance the H2O2 decomposition.

Jatkuvatoiminen ioninvaihto ja kompleksoituvien metallien sorptio kloridiympäristössä

Työn tarkoituksena oli tutkia kompleksoituvien metallien erotusta kloridiliuoksesta ioninvaihdolla. Kirjallisessa osassa perehdyttiin metallikompleksien muodostumiseen, ja erityisesti hopean, kalsiumin, magnesiumin, lyijyn ja sinkin muodostamiin komplekseihin kloridin ja nitraatin kanssa. Kirjallisessa osassa käsiteltiin myös metallien erottamista kiintopetikolonneissa jatkuvatoimisilla ioninvaihtomenetelmillä. Tässä työssä jatkuvatoimisen ioninvaihdon prosessivaihtoehdot jaoteltiin pyöriviin ja paikallaan pysyviin kolonneihin, sekä tarkasteltiin eri prosessivaihtoehtoja kolonnien kytkentöjen suhteen. Työn kokeellisessa osassa tutkittiin kahdenarvoisten metallien erottamista yhdenarvoisista metalleista sekä luotiin koedataa vastaavanlaisen erotusprosessin simulointiin. Kokeissa käytettiin anioninvaihtohartsia ja kelatoivaa selektiivistä ioninvaihtohartsia. Kahdenarvoisen kalsiumin, magnesiumin, lyijyn ja sinkin adsorptiota hartseihin tutkittiin tasapaino-, kinetiikka- ja kolonnikokeilla. Anioninvaihtohartsilla tehtyjen tasapaino- ja kolonnikokeiden tulokset osoittivat, että hartsi adsorboi tehokkaasti sinkkiä kloridiliuoksista, koska sinkki muodostaa stabiileja anionisia klorokomplekseja. Muiden tutkittujen kahdenarvoisten metallien adsorptio hartsiin oli huomattavasti vähäisempää. Tulosten perusteella tutkittu anioninvaihtohartsi on hyvä vaihtoehto sinkin erottamiseen muista tutkituista kahdenarvoisista metalleista kloridiympäristössä. Kelatoivalla hartsilla tehdyt tasapaino- ja kolonnikokeet osoittivat, että hartsi adsorboi kloridiliuoksista hyvin kahdenarvoista kalsiumia, magnesiumia, lyijyä ja sinkkiä, mutta ei adsorboi yhdenarvoista hopeaa. Tulosten perusteella kahdenarvoisten metallien erottaminen yhdenarvoisista metalleista voidaan toteuttaa kokeissa käytetyllä kelatoivalla ioninvaihtohartsilla.

Welding of additively manufactured stainless steel parts: Comparative study between sheet metal and selective laser melted parts

Additive manufacturing is a fast growing manufacturing technology capable of producing complex objects without the need for conventional manufacturing process planning. During the process the work piece is built by adding material one layer at a time according to a digital 3D CAD model. At first additive manufacturing was mainly used to make prototypes but the development of the technology has made it possible to also make final products. Welding is the most common joining method for metallic materials. As the maximum part size of additive manufacturing is often limited, it may sometimes be required to join two or more additively manufactured parts together. However there has been almost no research on the welding of additively manufactured parts so far, which means that there has been very little information available on the possible differences compared to the welding of sheet metal parts. The aim of this study was to compare the weld joint properties of additively manufactured parts to those of sheet metal parts. The welding process that was used was TIG welding and the test material was 316L austenitic stainless steel. Weld joint properties were studied by making tensile, bend and hardness tests and by studying the weld microstructures with a microscope. Results show that there are certain characteristics in the welds of additively manufactured parts. The building direction of the test pieces has some impact on the mechanical properties of the weld. Nevertheless all the welds exhibited higher yield strength than the sheet metal welds but at the same time elongation at break was lower. It was concluded that TIG welding is a feasible process for welding additively manufactured parts.

Photodamage to Oxygen Evolving Complex - An Initial Event in Photoinhibition of Photosystem II.

Photosystem II (PSII) of oxygenic photosynthesis is susceptible to photoinhibition. Photoinhibition is defined as light induced damage resulting in turnover of the D1 protein subunit of the reaction center of PSII. Both visible and ultraviolet (UV) light cause photoinhibition. Photoinhibition induced by UV light damages the oxygen evolving complex (OEC) via absorption of UV photons by the Mn ion(s) of OEC. Under visible light, most of the earlier hypotheses assume that photoinhibition occurs when the rate of photon absorption by PSII antenna exceeds the use of the absorbed energy in photosynthesis. However, photoinhibition occurs at all light intensities with the same efficiency per photon. The aim of my thesis work was to build a model of photoinhibition that fits the experimental features of photoinhibition. I studied the role of electron transfer reactions of PSII in photoinhibition and found that changing the electron transfer rate had only minor influence on photoinhibition if light intensity was kept constant. Furthermore, quenching of antenna excitations protected less efficiently than it would protect if antenna chlorophylls were the only photoreceptors of photoinhibition. To identify photoreceptors of photoinhibition, I measured the action spectrum of photoinhibition. The action spectrum showed resemblance to the absorption spectra of Mn model compounds suggesting that the Mn cluster of OEC acts as a photoreceptor of photoinhibition under visible light, too. The role of Mn in photoinhibition was further supported by experiments showing that during photoinhibition OEC is damaged before electron transfer activity at the acceptor side of PSII is lost. Mn enzymes were found to be photosensitive under visible and UV light indicating that Mn-containing compounds, including OEC, are capable of functioning as photosensitizers both in visible and UV light. The experimental results above led to the Mn hypothesis of the mechanism of continuous-light-induced photoinhibition. According to the Mn hypothesis, excitation of Mn of OEC results in inhibition of electron donation from OEC to the oxidized primary donor P680+ both under UV and visible light. P680 is oxidized by photons absorbed by chlorophyll, and if not reduced by OEC, P680+ may cause harmful oxidation of other PSII components. Photoinhibition was also induced with intense laser pulses and it was found that the photoinhibitory efficiency increased in proportion to the square of pulse intensity suggesting that laser-pulse-induced photoinhibition is a two-photon reaction. I further developed the Mn hypothesis suggesting that the initial event in photoinhibition under both continuous and pulsed light is the same: Mn excitation that leads to the inhibition of electron donation from OEC to P680+. Under laser-pulse-illumination, another Mn-mediated inhibitory photoreaction occurs within the duration of the same pulse, whereas under continuous light, secondary damage is chlorophyll mediated. A mathematical model based on the Mn hypothesis was found to explain photoinhibition under continuous light, under flash illumination and under the combination of these two.