Centralized Motion Control of a Linear Tooth Belt Drive: Analysis of the Performance and Limitations

A centralized robust position control for an electrical driven tooth belt drive is designed in this doctoral thesis. Both a cascaded control structure and a PID based position controller are discussed. The performance and the limitations of the system are analyzed and design principles for the mechanical structure and the control design are given. These design principles are also suitable for most of the motion control applications, where mechanical resonance frequencies and control loop delays are present. One of the major challenges in the design of a controller for machinery applications is that the values of the parameters in the system model (parameter uncertainty) or the system model it self (non-parametric uncertainty) are seldom known accurately in advance. In this thesis a systematic analysis of the parameter uncertainty of the linear tooth beltdrive model is presented and the effect of the variation of a single parameter on the performance of the total system is shown. The total variation of the model parameters is taken into account in the control design phase using a Quantitative Feedback Theory (QFT). The thesis also introduces a new method to analyze reference feedforward controllers applying the QFT. The performance of the designed controllers is verified by experimentalmeasurements. The measurements confirm the control design principles that are given in this thesis.

Three mechanical weed control techniques in spring cereals

Selostus: Kolme viljojen mekaanista rikkakasvintorjuntamentelmää

Effect of boric acid treatment on mechanical properties of laminated beech veneer lumber

Abstract

Influence of silvicultural regime on wood structure characteristics and mechanical properties of clear wood in Pinus sylvestris

Abstract

Optimal Mechanical PulpingProcesses for Eucalyptus, Acacia and Birch

Tässä diplomityössä tutkittiin ja vertailtiin eukalyptuksen, akaasian ja koivun kemimekaanista kuiduttamista ja valkaisua. Yleensä näitä puulajeja käytetään sellun keittoon. Puulajit eroavat toisistaan kasvupaikan ja kuiturakenteen osalta. Eukalyptus ja akaasia ovat niin sanottuja trooppisia lehtipuita, kun taas koivu kasvaa pohjoisilla vyöhykkeillä. Koivulla on kookkaimmat kuidut ja akaasialla pienimmät kuidut. Myös näiden lajien putkilot eroavat toisistaan. Koivun putkilot ovat pitkiä ja kapeita, kun taas eukalyptuksen ja akaasian putkilot ovat lyhyitä ja leveitä. Prosessiksi valittiin kaksivaiheinen APMP-prosessi. Koeajot tehtiinKeskuslaboratorio Oy:ssä. Massoille asetettiin seuraavat tavoitteet: freeness 150-200 ml ja vaaleus 80 %ISO. Eukalyptukselle ja koivulle tehtiin kaksi erilaista impregnointisarjaa, mutta akaasialle vain yksi. Jauhatuksen viimeisessä vaiheessa kokeiltiin myös jauhinvalkaisua. Jauhatuksen energiankulutus oli korkea varsinkin eukalyptuksella ja akaasialla. Jotta energiankulutus saataisiin pienemmäksi, tulisi käyttää enemmän lipeää, mutta se johtaa alkalitummumiseen. Lopuksi massat valkaistiin laboratoriossa. Eukalyptus ja koivu pystyttiin valkaisemaan vaaleuteen 80 %ISO, mutta eukalyptuksen valkaisu vaati enemmän peroksidia kuin koivun valkaisu. Akaasian lähtövaaleus oli niin alhainen, ettei siinä päästy tavoitevaaleuteen. Eukalyptuksella on parempi valonsironta ja paremmat lujuusominaisuudet kuin koivulla. Kemimekaanista massaa voidaan käyttää hienopaperissa parantamassa jäykkyyttä, bulkkia ja valonsirontaa, mutta usein ongelmana on alhainen vaaleus ja huono vaaleuden pysyvyys. Kemimekaanista massaa voidaankäyttää missä tahansa mekaanisissa painopapereissa. Mekaanisissa painopapereissa kemimekaanisella lehtipuumassalla voidaan korvata mekaanista havupuumassaa. Akaasia on niin tummaa, ettei sitä voida käyttää korkeavaaleuksisiin papereihin. Eukalyptus ja koivu ovat vaaleampia ja helpompia valkaista kuin akaasia, mutta myös niillä on niin huono vaaleudenpysyvyys että käyttö hienopapereissa on rajoittunutta. Mekaanisille eukalyptus ja koivumassoille hienopaperia parempi käyttökohde on mekaaniset painopaperit, kuten MWC-paperi.

The Influence of Process Conditions on the Deresination Efficiency in Mechanical Pulp Washing

The aim of this thesis was to produce information for the estimation of the flow balance of wood resin in mechanical pulping and to demonstrate the possibilities for improving the efficiency of deresination in practice. It was observed that chemical changes in wood resin take place only during peroxide bleaching, a significant amount of water dispersed wood resin is retained in the pulp mat during dewatering and the amount of wood resin in the solid phase of the process filtrates is very small. On the basis of this information there exist three parameters related to behaviour of wood resin that determine the flow balance in the process: 1. The liberation of wood resin to the pulp water phase 2. Theretention of water dispersed wood resin in dewatering 3. The proportion of wood resin degraded in the peroxide bleaching The effect of different factors on these parameters was evaluated with the help of laboratory studies and a literature survey. Also, information related to the values of these parameters in existing processes was obtained in mill measurements. With the help of this information, it was possible to evaluate the deresination efficiency and the effect of different factors on this efficiency in a pulping plant that produced low-freeness mechanical pulp. This evaluation showed that the wood resin content of mechanical pulp can be significantly decreased if there exists, in the process, a peroxide bleaching and subsequent washing stage. In the case of an optimal process configuration, as high as a 85 percent deresination efficiency seems to be possible with a water usage level of 8 m3/o.d.t.

Studies on integrating kinematic design method with mechanical systems simulation techniques

Theultimate goal of any research in the mechanism/kinematic/design area may be called predictive design, ie the optimisation of mechanism proportions in the design stage without requiring extensive life and wear testing. This is an ambitious goal and can be realised through development and refinement of numerical (computational) technology in order to facilitate the design analysis and optimisation of complex mechanisms, mechanical components and systems. As a part of the systematic design methodology this thesis concentrates on kinematic synthesis (kinematic design and analysis) methods in the mechanism synthesis process. The main task of kinematic design is to find all possible solutions in the form of structural parameters to accomplish the desired requirements of motion. Main formulations of kinematic design can be broadly divided to exact synthesis and approximate synthesis formulations. The exact synthesis formulation is based in solving n linear or nonlinear equations in n variables and the solutions for the problem areget by adopting closed form classical or modern algebraic solution methods or using numerical solution methods based on the polynomial continuation or homotopy. The approximate synthesis formulations is based on minimising the approximation error by direct optimisation The main drawbacks of exact synthesis formulationare: (ia) limitations of number of design specifications and (iia) failure in handling design constraints- especially inequality constraints. The main drawbacks of approximate synthesis formulations are: (ib) it is difficult to choose a proper initial linkage and (iib) it is hard to find more than one solution. Recentformulations in solving the approximate synthesis problem adopts polynomial continuation providing several solutions, but it can not handle inequality const-raints. Based on the practical design needs the mixed exact-approximate position synthesis with two exact and an unlimited number of approximate positions has also been developed. The solutions space is presented as a ground pivot map but thepole between the exact positions cannot be selected as a ground pivot. In this thesis the exact synthesis problem of planar mechanism is solved by generating all possible solutions for the optimisation process ¿ including solutions in positive dimensional solution sets - within inequality constraints of structural parameters. Through the literature research it is first shown that the algebraic and numerical solution methods ¿ used in the research area of computational kinematics ¿ are capable of solving non-parametric algebraic systems of n equations inn variables and cannot handle the singularities associated with positive-dimensional solution sets. In this thesis the problem of positive-dimensional solutionsets is solved adopting the main principles from mathematical research area of algebraic geometry in solving parametric ( in the mathematical sense that all parameter values are considered ¿ including the degenerate cases ¿ for which the system is solvable ) algebraic systems of n equations and at least n+1 variables.Adopting the developed solution method in solving the dyadic equations in direct polynomial form in two- to three-precision-points it has been algebraically proved and numerically demonstrated that the map of the ground pivots is ambiguousand that the singularities associated with positive-dimensional solution sets can be solved. The positive-dimensional solution sets associated with the poles might contain physically meaningful solutions in the form of optimal defectfree mechanisms. Traditionally the mechanism optimisation of hydraulically driven boommechanisms is done at early state of the design process. This will result in optimal component design rather than optimal system level design. Modern mechanismoptimisation at system level demands integration of kinematic design methods with mechanical system simulation techniques. In this thesis a new kinematic design method for hydraulically driven boom mechanism is developed and integrated in mechanical system simulation techniques. The developed kinematic design method is based on the combinations of two-precision-point formulation and on optimisation ( with mathematical programming techniques or adopting optimisation methods based on probability and statistics ) of substructures using calculated criteria from the system level response of multidegree-of-freedom mechanisms. Eg. by adopting the mixed exact-approximate position synthesis in direct optimisation (using mathematical programming techniques) with two exact positions and an unlimitednumber of approximate positions the drawbacks of (ia)-(iib) has been cancelled.The design principles of the developed method are based on the design-tree -approach of the mechanical systems and the design method ¿ in principle ¿ is capable of capturing the interrelationship between kinematic and dynamic synthesis simultaneously when the developed kinematic design method is integrated with the mechanical system simulation techniques.

Effect of Mechanical and Geometric Mismatching on Fatigue and Damage of Welded Joints

The future of high technology welded constructions will be characterised by higher strength materials and improved weld quality with respect to fatigue resistance. The expected implementation of high quality high strength steel welds will require that more attention be given to the issues of crack initiation and mechanical mismatching. Experiments and finite element analyses were performed within the framework of continuum damage mechanics to investigate the effect of mismatching of welded joints on void nucleation and coalescence during monotonic loading. It was found that the damage of undermatched joints mainly occurred in the sandwich layer and the damageresistance of the joints decreases with the decrease of the sandwich layer width. The damage of over-matched joints mainly occurred in the base metal adjacent to the sandwich layer and the damage resistance of the joints increases with thedecrease of the sandwich layer width. The mechanisms of the initiation of the micro voids/cracks were found to be cracking of the inclusions or the embrittled second phase, and the debonding of the inclusions from the matrix. Experimental fatigue crack growth rate testing showed that the fatigue life of under-matched central crack panel specimens is longer than that of over-matched and even-matched specimens. Further investigation by the elastic-plastic finite element analysis indicated that fatigue crack closure, which originated from the inhomogeneousyielding adjacent to the crack tip, played an important role in the fatigue crack propagation. The applicability of the J integral concept to the mismatched specimens with crack extension under cyclic loading was assessed. The concept of fatigue class used by the International Institute of Welding was introduced in the parametric numerical analysis of several welded joints. The effect of weld geometry and load condition on fatigue strength of ferrite-pearlite steel joints was systematically evaluated based on linear elastic fracture mechanics. Joint types included lap joints, angle joints and butt joints. Various combinations of the tensile and bending loads were considered during the evaluation with the emphasis focused on the existence of both root and toe cracks. For a lap joint with asmall lack-of-penetration, a reasonably large weld leg and smaller flank angle were recommended for engineering practice in order to achieve higher fatigue strength. It was found that the fatigue strength of the angle joint depended strongly on the location and orientation of the preexisting crack-like welding defects, even if the joint was welded with full penetration. It is commonly believed that the double sided butt welds can have significantly higher fatigue strength than that of a single sided welds, but fatigue crack initiation and propagation can originate from the weld root if the welding procedure results in a partial penetration. It is clearly shown that the fatigue strength of the butt joint could be improved remarkably by ensuring full penetration. Nevertheless, increasing the fatigue strength of a butt joint by increasing the size of the weld is an uneconomical alternative.

Development of rotating drum under mechanical and thermal load

A variable temperature field sets exacting demands to the structure under mechanical load. Most of all the lifetime of the rotating drum structure depends on temperature differences between parts inside the drum. The temperature difference was known because of the measurements made before. The list of demands was created based on customers’ needs. The limits of this paper were set to the inner structure of the drum. Creation of ideas for the inner structure was started open minded. The main principle in the creation process was to create new ideas for the function of the product with the help of sub-functions. The sub-functions were created as independent as possible. The best sub-functions were combined together and the new working principles were created based on them. Every working principle was calculated separately and criticized at the end of the calculation process. The main objective was to create the new kind of structure, which is not based too much to the old, inoperative structure. The affect of own weight of the inner structure to the stress values was quite small but it was also taken into consideration when calculating the maximum stress value of the structure. Because of very complex structures all of the calculations were made with the help of the ProE – Mechanica software. The fatigue analyze was made also for the best structure solution.

Purchasing Process Performance Definition and Improvement in the Mechanical Wood Industry

Tämän tutkimuksen ensisijaisena tavoitteena oli määrittää Schauman Wood Oy:n ostoprosessin suorituskyvyn nykytila yrityksen Suomen yksiköissä. Nykytila-arviointi suoritettiin uusien ja käytössä olevien mittaustulosten avulla. Tutkimuksessa verrattiin kymmenen tuotantolaitoksen ostoprosesseja keskenään. Keskeinen tutkimusongelma oli ostoprosessin suorituseroja aikaansaavien tekijöiden selvittäminen eri yksiköissä. Tutkimuksen tavoitteena oli saavuttaa yhtenäisemmät toimintatavat yrityksessä sekä laajentaa konsernin osto-organisaation hyödyntämistä hankintatoimessa. Tavoitteena oli ostoprosessin virtaviivaistaminen ja tehokkaamman seurantajärjestelmän kehittäminen. Ostotoimintojen suorituskyvyn jatkuva parantaminen perustuu osittain uusien mittareiden avulla saatavaan informaatioon ja täsmällisempään seurantaan. Sisäistä benchmarkingia käytettiin työkaluna suorituskyky-eroavaisuuksien määrittelyssä. Tietoa erilaisista toimintatavoista kerättiin haastattelemalla yrityksen ostajia ja tehdaspalvelupäälliköitä eri tehdaspaikkakunnilla. Sisäisen benchmarkingin avulla määriteltiin toimintatapa eroavaisuudet sekä kehitettiin seurantakortti, jossa jokaista yksikköä verrataan parhaaseen ja eniten kehittyneeseen yksikköön. Työn tuloksina muodostui ehdotuksia ostotoiminnon uusiksi mittareiksi. Uudet mittarit ovat tehokkuusmittareita, jotka kuvaavat resurssien käytön tehokkuutta sekä auttavat seuraamaan ostoprosessin tilaa entistä paremmin. Uusien mittareiden tavoitteena on myös vähentää mittareiden manipulaatiomahdollisuutta. Työn ulkopuolelle rajattiin informaatioteknologiajärjestelmien tietotekninen osuus. Eräs yrityksen tuotantolaitoksista rajattiin myös työn ulkopuolelle, koska sen ostoprosessit ovat huomattavasti kehittymättömämpiä kuin Schauman Woodin muiden tehtaiden ostoprosessit. Kyseisen yksikön kehittämisen tulee lähteä aivan ruohonjuuritasolta. Tutkimuksen teoriaosuus on kerätty alan ammattikirjallisuudesta ja tutkimuksen aihetta käsittelevistä uudehkoista tieteellisistä alan artikkeleista. Teorian tarkoituksena on tukea empiiristä osuutta sekä antaa lukijalle uusia näkemyksiä ostotoiminnan monista mahdollisuuksista. Tutkimuksen tuloksia ovat nykytila-analyysi, ehdotukset uusista ostotoiminnan mittareista sekä ehdotus MRO-tuotteiden ulkoistamiskokeilusta. Yrityksen ostotoiminnan tulisi kehittyä operatiivisesta tasosta kohti strategisempaa oston tasoa. Johdon sitoutuminen hankintatoimen kehityshankkeisiin on erityisen tärkeää, lisäksi hankintatoimi tulisi nähdä strategisempana osa-alueena yrityksessä. Hankintatoimen kehittämisen avulla yrityksen kustannustehokkuutta voidaan lisätä merkittävästi.

Flexible Multibody Simulation Approach in the Dynamic Analysis of Bone Strains Activity

The objective of this study is to show that bone strains due to dynamic mechanical loading during physical activity can be analysed using the flexible multibody simulation approach. Strains within the bone tissue play a major role in bone (re)modeling. Based on previous studies, it has been shown that dynamic loading seems to be more important for bone (re)modeling than static loading. The finite element method has been used previously to assess bone strains. However, the finite element method may be limited to static analysis of bone strains due to the expensive computation required for dynamic analysis, especially for a biomechanical system consisting of several bodies. Further, in vivo implementation of strain gauges on the surfaces of bone has been used previously in order to quantify the mechanical loading environment of the skeleton. However, in vivo strain measurement requires invasive methodology, which is challenging and limited to certain regions of superficial bones only, such as the anterior surface of the tibia. In this study, an alternative numerical approach to analyzing in vivo strains, based on the flexible multibody simulation approach, is proposed. In order to investigate the reliability of the proposed approach, three 3-dimensional musculoskeletal models where the right tibia is assumed to be flexible, are used as demonstration examples. The models are employed in a forward dynamics simulation in order to predict the tibial strains during walking on a level exercise. The flexible tibial model is developed using the actual geometry of the subject’s tibia, which is obtained from 3 dimensional reconstruction of Magnetic Resonance Images. Inverse dynamics simulation based on motion capture data obtained from walking at a constant velocity is used to calculate the desired contraction trajectory for each muscle. In the forward dynamics simulation, a proportional derivative servo controller is used to calculate each muscle force required to reproduce the motion, based on the desired muscle contraction trajectory obtained from the inverse dynamics simulation. Experimental measurements are used to verify the models and check the accuracy of the models in replicating the realistic mechanical loading environment measured from the walking test. The predicted strain results by the models show consistency with literature-based in vivo strain measurements. In conclusion, the non-invasive flexible multibody simulation approach may be used as a surrogate for experimental bone strain measurement, and thus be of use in detailed strain estimation of bones in different applications. Consequently, the information obtained from the present approach might be useful in clinical applications, including optimizing implant design and devising exercises to prevent bone fragility, accelerate fracture healing and reduce osteoporotic bone loss.

Nuclear magnetic resonance investigation of structure and dynamics of some electrolyte solutions

Electrolyte solutions are of importance in a wide range of scientific contexts and as such have attracted considerable theoretical and experimental effort over many years. Nuclear Magnetic resonance provides a precise and versatile tool for investigation of electrolyte solutions, both in water and in organic solvents. Many structural and dynamic properties can be obtained through NMR experiments. The solution of aluminum chloride in water was studied. Different concentrations were taken for investigation. Independence of maximum line shift from concentration and acidity was shown. Six-coordinated structure of solvation shell was confirmed by experiments on 'H and 27A1 nuclei. Diffusion coefficients were studied. The solution of nickel chloride in methanol was studied. Lines, corresponding to coordinated and bulk methanol were found. Four-, five- and six-coordinated structures were found in different temperatures. The line for coordinated -OD group of deuterated methanol was observed on 2H spectrum for the first time. Partial deuteration of CH3 group was detected. Inability to observe coordinated -OH group was explained.