Electrochemical Characterisation of Filter Media Properties and Their Exploitation in Enhanced Filtration

Streaming potential measurements for the surface charge characterisation of different filter media types and materials were used. The equipment was developed further so that measurements could be taken along the surfaces, and so that tubular membranes could also be measured. The streaming potential proved to be a very useful tool in the charge analysis of both clean and fouled filter media. Adsorption and fouling could be studied, as could flux, as functions of time. A module to determine the membrane potential was also constructed. The results collected from the experiments conducted with these devices were used in the study of the theory of streaming potential as an electrokinetic phenomenon. Several correction factors, which are derived to take into account the surface conductance and the electrokinetic flow in very narrow capillaries, were tested in practice. The surface materials were studied using FTIR and the results compared with those from the streaming potentials. FTIR analysis was also found to be a useful tool in the characterisation of filters, as well as in the fouling studies. Upon examination of the recorded spectra from different depths in a sample it was possible to determine the adsorption sites. The influence of an external electric field on the cross flow microflltration of a binary protein system was investigated using a membrane electroflltration apparatus. The results showed that a significant improvement could be achieved in membrane filtration by using the measured electrochemical properties to help adjust the process conditions.

Recovery of Hemicelluloses from Wood Hydrolysates by Membrane Filtration

Hemicelluloses are among the most important natural resources that contain polysaccharides. In this study the separation and purification of hemicelluloses from water extraction liquors containing wood hemicelluloses, lignin compounds and monosaccharide by using membrane filtration was investigated. The isolation of the hemicelluloses from the wood hydrolysates was performed in two steps: concentration of high molar mass hemicelluloses by ultrafiltration and separation of low molar mass hemicelluloses from monomeric sugars using tight ultrafiltration membranes. The purification of the retained hemicelluloses was performed by diafiltration. During the filtration experiments, the permeate flux through ultrafiltration and tight ultrafiltration membranes was relatively high. The fouling ability of the used membranes was relatively low. In our experiments, the retention of hemicelluloses using two filtration steps was almost complete. The separation of monosaccharides from hemicelluloses was relatively high and the purification of hemicelluloses by diafiltration was highly efficient. The separation of lignin from hemicelluloses was partially achieved. Diafiltration showed potential to purify retained hemicelluloses from lignin and other organics. The best separation of lignin from hemicelluloses in the first filtration step was obtained using the UC005 membrane. The GE-5 and ETNA01PP membranes showed potential to purify and separate lignin from hemicelluloses. However, the feed solution of the second filtration stages (from different ultrafiltration membranes) affected the permeate flux and the separation of various extracted compounds from hemicelluloses. The GE-5 and ETNA01PP membranes gave the efficient purification of the hemicelluloses when using diafiltration. Separation of degraded xylan from glucomannan (primary spruce hemicelluloses) was also possible using membrane filtration. The best separation was achieved using the GE-5 membrane. The retention of glucomannan was three times higher than xylan retention.

Identification of extractives and polysaccharides as foulants in membrane filtration of pulp and paper mill effluents

The search for new renewable materials has intensified in recent years. Pulp and paper mill process streams contain a number of potential compounds which could be used in biofuel production and as raw materials in the chemical, food and pharmaceutical industries. Prior to utilization, these compounds require separation from other compounds present in the process stream. One feasible separation technique is membrane filtration but to some extent, fouling still limits its implementation in pulp and paper mill applications. To mitigate fouling and its effects, foulants and their fouling mechanisms need to be well understood. This thesis evaluates fouling in filtration of pulp and paper mill process streams by means of polysaccharide model substance filtrations and by development of a procedure to analyze and identify potential foulants, i.e. wood extractives and carbohydrates, from fouled membranes. The model solution filtration results demonstrate that each polysaccharide has its own fouling mechanism, which also depends on the membrane characteristics. Polysaccharides may foul the membranes by adsorption and/or by gel/cake layer formation on the membrane surface. Moreover, the polysaccharides interact, which makes fouling evaluation of certain compound groups very challenging. Novel methods to identify wood extractive and polysaccharide foulants are developed in this thesis. The results show that it is possible to extract and identify wood extractives from membranes fouled in filtration of pulp and paper millstreams. The most effective solvent was found to be acetone:water (9:1 v/v) because it extracted both lipophilic extractives and lignans at high amounts from the fouled membranes and it was also non-destructive for the membrane materials. One hour of extraction was enough to extract wood extractives at high amounts for membrane samples with an area of 0.008 m2. If only qualitative knowledge of wood extractives is needed a simplified extraction procedure can be used. Adsorption was the main fouling mechanism in extractives-induced fouling and dissolved fatty and resin acids were mostly the reason for the fouling; colloidal fouling was negligible. Both process water and membrane characteristics affected extractives-induced fouling. In general, the more hydrophilic regenerated cellulose (RC) membrane fouled less that the more hydrophobic polyethersulfone (PES) and polyamide (PA) membranes independent of the process water used. Monosaccharide and uronic acid units could also be identified from the fouled synthetic polymeric membranes. It was impossible to analyze all monosaccharide units from the RC membrane because the analysis result obtained contained degraded membrane material. One of the fouling mechanisms of carbohydrates was adsorption. Carbohydrates were not potential adsorptive foulants to the sameextent as wood extractives because their amount in the fouled membranes was found to be significantly lower than the amount of wood extractives.

Recovery of biomass-derived valuable compounds using chromatographic and membrane separations

Utilization of biomass-based raw materials for the production of chemicals and materials is gaining an increasing interest. Due to the complex nature of biomass, a major challenge in its refining is the development of efficient fractionation and purification processes. Preparative chromatography and membrane filtration are selective, energy-efficient separation techniques which offer a great potential for biorefinery applications. Both of these techniques have been widely studied. On the other hand, only few process concepts that combine the two methods have been presented in the literature. The aim of this thesis was to find the possible synergetic effects provided by combining chromatographic and membrane separations, with a particular interest in biorefinery separation processes. Such knowledge could be used in the development of new, more efficient separation processes for isolating valuable compounds from complex feed solutions that are typical for the biorefinery environment. Separation techniques can be combined in various ways, from simple sequential coupling arrangements to fully-integrated hybrid processes. In this work, different types of combined separation processes as well as conventional chromatographic separation processes were studied for separating small molecules such as sugars and acids from biomass hydrolysates and spent pulping liquors. The combination of chromatographic and membrane separation was found capable of recovering high-purity products from complex solutions. For example, hydroxy acids of black liquor were successfully recovered using a novel multistep process based on ultrafiltration and size-exclusion chromatography. Unlike any other separation process earlier suggested for this challenging separation task, the new process concept does not require acidification pretreatment, and thus it could be more readily integrated into a pulp-mill biorefinery. In addition to the combined separation processes, steady-state recycling chromatography, which has earlier been studied for small-scale separations of high-value compounds only, was found a promising process alternative for biorefinery applications. In comparison to conventional batch chromatography, recycling chromatography provided higher product purity, increased the production rate and reduced the chemical consumption in the separation of monosaccharides from biomass hydrolysates. In addition, a significant further improvement in the process performance was obtained when a membrane filtration unit was integrated with recycling chromatography. In the light of the results of this work, separation processes based on combining membrane and chromatographic separations could be effectively applied for different biorefinery applications. The main challenge remains in the development of inexpensive separation materials which are resistant towards harsh process conditions and fouling.

Reverse osmosis membrane surface modification: effects on membrane performance

The aim of this thesis was to study the surface modification of reverse osmosis membranes by surfactants and the effect of modification on rejection and flux. The surfactants included anionic and nonionic surfactants. The purpose of membrane modification was to improve pure water permeability with increasing salt rejection. The literature part of the study deals with the basic principles of reverse osmosis technology and factors affecting the membrane performance. Also the membrane surface modification by surfactants and their influence on membrane’s surface properties and efficiency (permeability and salt rejection) were discussed. In the experimental part of the thesis two thin-film composite membranes, Desal AG and LE-4040, were modified on-line with three different surfactants. The effects of process parameters (pressure, pH, and surfactant concentration) on surface modification were also examined. The characteristics of the modified membranes were determined by measuring the membranes’ contact angle and zeta potentials. The zeta potential and contact angle measurements indicate that the surfactants were adsorbed onto the both membranes. However, the adsorption did not effect on membrane’s pure water permeability and salt rejection. Thereby, the surface modification of the Desal AG and LE-4040 membranes by surfactants was not able to improve the membrane’s performance.

Membrane development for oil contaminated water treatments

The aim of this Master’s thesis study was to develop a membrane for oil contaminated water treatments. Oily wastewaters are a big problem to environment and therefore it is important to find an efficient method for their treatment. There are several treatment methods, but one of the most promising methods is membrane filtration. In the theoretical part of this study the membrane technology and polymeric membrane preparation with phase inversion and membrane modification methods was discussed. It was also told about the most important properties of the membranes. Oily waters, their treatment methods and oily wastewater sources were discussed more specifically. In the experimental part membranes from cellulose acetate were prepared and membranes were modified with two different methods. Modification methods were surface modification and polymer mixing. The modification purpose was to make membranes more hydrophilic and increase surface charge, which can reduce fouling. Membranes were characterized by determining zeta potential, contact angle, oil retention, pure water permeability, pressure-normalized flux and fouling. It were used both synthetic and real spent oil-water emulsion in membrane filtration. Surface modification resulted membranes, which had better properties than unmodified membrane. The amount of substance used in surface modification affected a lot to membrane properties, so it would be necessary to try different amounts of substance to develop the best membrane for oil-water emulsion treatment.