A novel approachfor assessing the fatigue strength of ultrasonic impact treated welded structures.

It is commonly observed that complex fabricated structures subject tofatigue loading fail at the welded joints. Some problems can be corrected by proper detail design but fatigue performance can also be improved using post-weld improvement methods. In general, improvement methods can be divided into two main groups: weld geometry modification methods and residual stress modification methods. The former remove weld toe defects and/or reduce the stress concentrationwhile the latter introduce compressive stress fields in the area where fatigue cracks are likely to initiate. Ultrasonic impact treatment (UIT) is a novel post-weld treatment method that influences both the residual stress distribution andimproves the local geometry of the weld. The structural fatigue strength of non-load carrying attachments in the as-welded condition has been experimentally compared to the structural fatigue strength of ultrasonic impact treated welds. Longitudinal attachment specimens made of two thicknesses of steel S355 J0 have been tested for determining the efficiency of ultrasonic impacttreatment. Treated welds were found to have about 50% greater structural fatigue strength, when the slope of the S-N-curve is three. High mean stress fatigue testing based on the Ohta-method decreased the degree of weld improvement only 19%. This indicated that the method could be also applied for large fabricated structures operating under high reactive residual stresses equilibrated within the volume of the structure. The thickness of specimens has no significant effect tothe structural fatigue strength. The fatigue class difference between 5 mm and 8 mm specimen was only 8%. It was hypothesized that the UIT method added a significant crack initiation period to the total fatigue life of the welded joints. Crack initiation life was estimated by a local strain approach. Material parameters were defined using a modified Uniform Material Law developed in Germany. Finite element analysis and X-ray diffraction were used to define, respectively, the stress concentration and mean stress. The theoretical fatigue life was found to have good accuracy comparing to experimental fatigue tests.The predictive behaviour of the local strain approach combined with the uniformmaterial law was excellent for the joint types and conditions studied in this work.

Information System ProcessInnovation Adoption, Adaptation, Learning, and Unlearning: A Longitudinal Case Study

This thesis examines the history and evolution of information system process innovation (ISPI) processes (adoption, adaptation, and unlearning) within the information system development (ISD) work in an internal information system (IS) department and in two IS software house organisations in Finland over a 43-year time-period. The study offers insights into influential actors and their dependencies in deciding over ISPIs. The research usesa qualitative research approach, and the research methodology involves the description of the ISPI processes, how the actors searched for ISPIs, and how the relationships between the actors changed over time. The existing theories were evaluated using the conceptual models of the ISPI processes based on the innovationliterature in the IS area. The main focus of the study was to observe changes in the main ISPI processes over time. The main contribution of the thesis is a new theory. The term theory should be understood as 1) a new conceptual framework of the ISPI processes, 2) new ISPI concepts and categories, and the relationships between the ISPI concepts inside the ISPI processes. The study gives a comprehensive and systematic study on the history and evolution of the ISPI processes; reveals the factors that affected ISPI adoption; studies ISPI knowledge acquisition, information transfer, and adaptation mechanisms; and reveals the mechanismsaffecting ISPI unlearning; changes in the ISPI processes; and diverse actors involved in the processes. The results show that both the internal IS department and the two IS software houses sought opportunities to improve their technical skills and career paths and this created an innovative culture. When new technology generations come to the market the platform systems need to be renewed, and therefore the organisations invest in ISPIs in cycles. The extent of internal learning and experiments was higher than the external knowledge acquisition. Until the outsourcing event (1984) the decision-making was centralised and the internalIS department was very influential over ISPIs. After outsourcing, decision-making became distributed between the two IS software houses, the IS client, and itsinternal IT department. The IS client wanted to assure that information systemswould serve the business of the company and thus wanted to co-operate closely with the software organisations.

Kylmämuovatun putkipalkin väsyminen metsätyökoneen puomirakenteessa

Työssä on tutkittu kylmämuovatun suorakaideputkipalkin väsymistä metsätyökoneen puomirakenteen osana. Kylmämuovatun putkipalkin sisäpintaan syntyy käytössä puristavan ulkoisen kuormituksen vaikutuksesta putkipalkin pituussuunnassa sekä seinämän läpi kasvavia säröjä. Työn tarkoituksena on ollut selvittää rakenteen väsymiskestoikä sekä säröytymisen aiheuttavat tekijät. Työssä on verrattu kestoikälaskentaan ja särönkasvuun sovellettujen murtumismekaniikan ja elementtimenetelmän tuloksia laboratoriokokeista saatuihin tuloksiin. Toisiaan tukevien tulosten perusteella kylmämuovausprosessissa syntyneiden jäännösjännitysten osuus särön ydintymisessä, kasvussa ja sen käyttäytymisessä on ulkoisen kuorman paikallisen vaikutuksen lisänä erittäin merkittävä. Putkipalkin väsyminen onkin jäännösjännityksistä riippuva särönkasvuilmiö.

Predictors and Correlates of Substance Use among Young Men. The Longitudinal “From a Boy to a Man” Birth Cohort Study.

Substance use is one of our most important public health problems. Studying risk factors in a longitudinal study setting helps to identify subgroups of young people at greater risk for substance-use-related problems, and to facilitate targeted prevention efforts. The aim of this thesis was to study childhood predictors and correlates of substance-use-related outcomes among young men in a longitudinal, nationwide birth cohort study. The study population included 10% of all Finnish-speaking boys born in Finland in 1981 (n=2946, 97% of the target population). In 1989, at age eight, valid measures of psychiatric symptoms (Rutter questionnaires and Children’s Depression Inventory) were obtained from parents, teachers and the boys themselves. In 1999, at age 18, boys were reached at their obligatory military call-up (n=2348, 80% of the boys attending the study in 1989). Self-reports of substance use, psychopathology, adaptive functioning (Young Adult Self-Report), and mental health service use were obtained through questionnaires. Information about psychiatric diagnoses from the Military Register (age 18-23 years) and information about offending from the National Police Register (age 16-20 years) were collected in early adulthood (92% of the 1989sample). Boys with childhood conduct, hyperactive, and comorbid conduct-emotional problems had elevated rates of substance use and substance-use-related crime in early adulthood. Depressive symptoms predicted daily smoking, especially among boys of low-educated fathers. Emotional problems predicted lower occurrence of drunkenness-related alcohol use and smoking. Teacher reports on boys’ problem behaviour had the best predictive power for later substance use. At age 18, frequent drunkenness associated with delinquency, smoking and illicit drug use, and having friends. Occasional drunkenness associated with better psychosocial functioning in general compared to boys with frequent drunkenness or without drunkenness-related alcohol use. Illicit drug use without drug offending was not predicted by childhood psychiatric symptoms, but 22% of boys with illicit drug use had a psychiatric diagnosis in early adulthood. Drug offenders, in turn, had psychiatric problems both in childhood and in adulthood. Psychiatric disorders were common among young men with substance-use-related crime. Recidivist crime associated strongly with having a substance use disorder diagnosis according to the Military Register. At age 18, frequent drunkenness was common among boys entering mental health services, but entering substance use treatment was non-existent. According to the findings of this thesis, substance-use-related outcomes accumulate in boys having psychiatric problems both in childhood and in early adulthood. Targeted early interventions in school health care systems, particularly for boys with childhood hyperactive, conduct, and comorbid conduct-emotional problems are recommended. Psychiatric problems and risky behaviours, such as delinquency should always be assessed alongside substance use. Specialized and multidisciplinary care are required for young men who have multiple or complex needs, for instance, for young men with drug offending and recidivist crime. Integrating a substance use treatment perspective with other services where young men are encountered is emphasized.

Bordetella pertussis - Vaccination and Strain Variation

Pertussis or whooping cough is a highly contagious vaccine-preventable disease of the human respiratory tract caused by the Bordetella pertussis bacteria. In Finland, pertussis vaccinations were started in 1952 leading to a dramatic decrease in the morbidity and mortality. In the late 1990s, the incidence of pertussis increased despite the high vaccination coverage. Strain variation has been connected to the re-emergence of pertussis in countries with long history of pertussis vaccination. In 2005, the pertussis vaccine and the vaccination schedule were changed in Finland. The molecular epidemiology and the strain variation of the B. pertussis isolates were examined in Finland and in countries with similar (France) and different (Sweden) vaccination history. Continuous evolution of the B. pertussis population in Finland was observed since the 1950s, and the recently circulating isolates were antigenically different from the vaccine strains. Comparison of the circulating isolates from Finland, France and Sweden did not refer to significant differences. Certain type of strains noticed in France already in 1994 mainly caused the recent epidemics in Sweden (1999) and in Finland (2003-4). On several occasions, a new type of strains first appeared in Sweden and some years later in Finland. The B. pertussis isolates from the infants were shown to be similar to those from the other age groups. It is suggested that the strains originate from the same reservoir among adolescents and adults. The strain variation does not seem to have a major effect on the morbidity among recently vaccinated individuals, but it might play a role among those who are in the waning phase of immunity. The incidence of pertussis in Finland has remained low since the change of the vaccination programme. This might be related to the epidemic nature of pertussis and the near future will show the real effectiveness of the new vaccination programme. At present, many infants are infected because they are too young to be immunised with the current schedule. New strategies or vaccines are needed to protect those who are the most vulnerable.

The Effects of Some Furnish and Paper Structure Related Factors on Wet Web Tensile and Relaxation Characteristics

The objective of this thesis was to identify the effects of different factors on the tension and tension relaxation of wet paper web after high-speed straining. The study was motivated by the plausible connection between wet web mechanical properties and wet web runnability on paper machines shown by previous studies. The mechanical properties of wet paper were examined using a fast tensile test rig with a strain rate of 1000%/s. Most of the tests were carried out with laboratory handsheets, but samples from a pilot paper machine were also used. The tension relaxation of paper was evaluated as the tension remaining after 0.475 s of relaxation (residual tension). The tensile and relaxation properties of wet webs were found to be strongly dependent on the quality and amount of fines. With low fines content, the tensile strength and residual tension of wet paper was mainly determined by the mechanical interactions between fibres at their contact points. As the fines strengthen the mechanical interaction in the network, the fibre properties also become important. Fibre deformations caused by the mechanical treatment of pulp were shown to reduce the mechanical properties of both dry and wet paper. However, the effect was significantly higher for wet paper. An increase of filler content from 10% to 25% greatly reduced the tensile strength of dry paper, but did not significantly impair wet web tensile strength or residual tension. Increased filler content in wet web was shown to increase the dryness of the wet web after the press section, which partly compensates for the reduction of fibrous material in the web. It is also presumable that fillers increase entanglement friction between fibres, which is beneficial for wet web strength. Different contaminants present in white water during sheet formation resulted in lowered surface tension and increased dryness after wet pressing. The addition of different contaminants reduced the tensile strength of the dry paper. The reduction of dry paper tensile strength could not be explained by the reduced surface tension, but rather on the tendency of different contaminants to interfere with the inter-fibre bonding. Additionally, wet web strength was not affected by the changes in the surface tension of white water or possible changes in the hydrophilicity of fibres caused by the addition of different contaminants. The spraying of different polymers on wet paper before wet pressing had a significant effect on both dry and wet web tensile strength, whereas wet web elastic modulus and residual tension were basically not affected. We suggest that the increase of dry and wet paper strength could be affected by the molecular level interactions between these chemicals and fibres. The most significant increases in dry and wet paper strength were achieved with a dual application of anionic and cationic polymers. Furthermore, selectively adding papermaking chemicals to different fibre fractions (as opposed to adding chemicals to the whole pulp) improved the wet web mechanical properties and the drainage of the pulp suspension.

Possibilities and challenges of longitudinal studies in operations management

Longitudinal studies are quite rare in the area of Operations Management. One reason might be the time needed to conduct such studies, and then the lack of experience and real-life examples and results. The aim of the thesis is to examine longitudinal studies in the area of OM and the possible advantages, challenges and pitfalls of such studies. A longitudinal benchmarking study, Made in Finland, was analyzed in terms of the study methodology and its outcomes. The timeline of this longitudinal study is interesting. The first study was made in 1993, the second in 2004 and the third in 2010. Between these studies some major changes occurred in the Finnish business environment. Between the first and second studies, Finland joined the ETA and the EU, and globalization started with the rise of the Internet era, while between the second and third studies financial turmoil started in 2007. The sample and cases used in this study were originally 23 manufacturing sites in Finland. These sites were interviewed in 1993, in 2004 and 2010. One important and interesting aspect is that all the original sites participated in 2004, and 19 sites were still able to participate in 2010. Four sites had been closed and/or moved abroad. All of this gave a good opportunity to study the changes that occurred in the Finnish manufacturing sites and their environment, and how they reacted to these changes, and the effects on their performance. It is very seldom, if ever, that the same manufacturing sites have been studied in a longitudinal setting by using three data points. The results of this study are thus unique, and the experience gained is valuable for practitioners.

Flexible multibody approach in bone strain estimation during physical activity:

Bone strain plays a major role as the activation signal for the bone (re)modeling process, which is vital for keeping bones healthy. Maintaining high bone mineral density reduces the chances of fracture in the event of an accident. Numerous studies have shown that bones can be strengthened with physical exercise. Several hypotheses have asserted that a stronger osteogenic (bone producing) effect results from dynamic exercise than from static exercise. These previous studies are based on short-term empirical research, which provide the motivation for justifying the experimental results with a solid mathematical background. The computer simulation techniques utilized in this work allow for non-invasive bone strain estimation during physical activity at any bone site within the human skeleton. All models presented in the study are threedimensional and actuated by muscle models to replicate the real conditions accurately. The objective of this work is to determine and present loading-induced bone strain values resulting from physical activity. It includes a comparison of strain resulting from four different gym exercises (knee flexion, knee extension, leg press, and squat) and walking, with the results reported for walking and jogging obtained from in-vivo measurements described in the literature. The objective is realized primarily by carrying out flexible multibody dynamics computer simulations. The dissertation combines the knowledge of finite element analysis and multibody simulations with experimental data and information available from medical field literature. Measured subject-specific motion data was coupled with forward dynamics simulation to provide natural skeletal movement. Bone geometries were defined using a reverse engineering approach based on medical imaging techniques. Both computed tomography and magnetic resonance imaging were utilized to explore modeling differences. The predicted tibia bone strains during walking show good agreement with invivo studies found in the literature. Strain measurements were not available for gym exercises; therefore, the strain results could not be validated. However, the values seem reasonable when compared to available walking and running invivo strain measurements. The results can be used for exercise equipment design aimed at strengthening the bones as well as the muscles during workout. Clinical applications in post fracture recovery exercising programs could also be the target. In addition, the methodology introduced in this study, can be applied to investigate the effect of weightlessness on astronauts, who often suffer bone loss after long time spent in the outer space.

Searching for keys to successful post-merger integration : a longitudinal case-study following a public sector merger

Unsuccessful mergers are unfortunately the rule rather than the exception. Therefore it is necessary to gain an enhanced understanding of mergers and post-merger integrations (PMI) as well as learning more about how mergers and PMIs of information systems (IS) and people can be facilitated. Studies on PMI of IS are scarce and public sector mergers are even less studied. There is nothing however to indicate that public sector mergers are any more successful than those in the private sector. This thesis covers five studies carried out between 2008 and 2011 in two organizations in higher education that merged in January 2010. The most recent study was carried out two years after the new university was established. The longitudinal case-study focused on the administrators and their opinions of the IS, the work situation and the merger in general. These issues were investigated before, during and after the merger. Both surveys and interviews were used to collect data, to which were added documents that both describe and guide the merger process; in this way we aimed at a triangulation of findings. Administrators were chosen as the focus of the study since public organizations are highly dependent on this staff category, forming the backbone of the organization and whose performance is a key success factor for the organization. Reliable and effective IS are also critical for maintaining a functional and effective organization, and this makes administrators highly dependent on their organizations’ IS for the ability to carry out their duties as intended. The case-study has confirmed the administrators’ dependency on IS that work well. A merger is likely to lead to changes in the IS and the routines associated with the administrators’ work. Hence it was especially interesting to study how the administrators viewed the merger and its consequences for IS and the work situation. The overall research objective is to find key issues for successful mergers and PMIs. The first explorative study in 2008 showed that the administrators were confident of their skills and knowledge of IS and had no fear of having to learn new IS due to the merger. Most administrators had an academic background and were not anxious about whether IS training would be given or not. Before the merger the administrators were positive and enthusiastic towards the merger and also to the changes that they expected. The studies carried out before the merger showed that these administrators were very satisfied with the information provided about the merger. This information was disseminated through various channels and even negative information and postponed decisions were quickly distributed. The study conflicts with the theories that have found that resistance to change is inevitable in a merger. Shortly after the merger the (third) study showed disappointment with the fact that fewer changes than expected had been implemented even if the changes that actually were carried out sometimes led to a more problematic work situation. This was seen to be more prominent for routine changes than IS changes. Still the administrators showed a clear willingness to change and to share their knowledge with new colleagues. This knowledge sharing (also tacit) worked well in the merger and the PMI. The majority reported that the most common way to learn to use new ISs and to apply new routines was by asking help from colleagues. They also needed to take responsibility for their own training and development. Five months after the merger (the fourth study) the administrators had become worried about the changes in communication strategy that had been implemented in the new university. This was perceived as being more anonymous. Furthermore, it was harder to get to know what was happening and to contact the new decision makers. The administrators found that decisions, and the authority to make decisions, had been moved to a higher administrative level than they were accustomed to. A directive management style is recommended in mergers in order to achieve a quick transition without distracting from the core business. A merger process may be tiresome and require considerable effort from the participants. In addition, not everyone can make their voice heard during a merger and consensus is not possible in every question. It is important to find out what is best for the new organization instead of simply claiming that the tried and tested methods of doing things should be implemented. A major problem turned out to be the lack of management continuity during the merger process. Especially problematic was the situation in the IS-department with many substitute managers during the whole merger process (even after the merger was carried out). This meant that no one was in charge of IS-issues and the PMI of IS. Moreover, the top managers were appointed very late in the process; in some cases after the merger was carried out. This led to missed opportunities for building trust and management credibility was heavily affected. The administrators felt neglected and that their competences and knowledge no longer counted. This, together with a reduced and altered information flow, led to rumours and distrust. Before the merger the administrators were convinced that their achievements contributed value to their organizations and that they worked effectively. After the merger they were less sure of their value contribution and effectiveness even if these factors were not totally discounted. The fifth study in November 2011 found that the administrators were still satisfied with their IS as they had been throughout the whole study. Furthermore, they believed that the IS department had done a good job despite challenging circumstances. Both the former organizations lacked IS strategies, which badly affected the IS strategizing during the merger and the PMI. IS strategies deal with issues like system ownership; namely who should pay and who is responsible for maintenance and system development, for organizing system training for new IS, and for effectively run IS even during changing circumstances (e.g. more users). A proactive approach is recommended for IS strategizing to work. This is particularly true during a merger and PMI for handling issues about what ISs should be adopted and implemented in the new organization, issues of integration and reengineering of IS-related processes. In the new university an ITstrategy had still not been decided 26 months after the new university was established. The study shows the importance of the decisive management of IS in a merger requiring that IS issues are addressed in the merger process and that IS decisions are made early. Moreover, the new management needs to be appointed early in order to work actively with the IS-strategizing. It is also necessary to build trust and to plan and make decisions about integration of IS and people.

Pregnancy and periodontium. A clinical, microbiological, and enzymological approach via a longitudinal study

The mechanisms leading to an enhanced susceptibility to gingivitis in pregnant women have not yet been completely described. Therefore, the current study series were performed to investigate longitudinally the influence of pregnancy on periodontal tissues, and to evaluate microbial and host response factors related to pregnancy gingivitis formation. Pregnancy-related periodontal changes were analysed in 30 generally healthy women (24- 35 years old) once per trimester, till the end of lactation. Matched non-pregnant women (n=24) served as the controls, and were examined three times, once per following month. Pregnancy-related gingival inflammation was observed as enhanced tendency towards gingival bleeding and pseudopocket formation with a concomitant decrease in plaque levels. Gingivitis reached its peak during mid-pregnancy and then decreased transiently visit by visit. After lactation, no differences in periodontal status were seen between the study and control populations. In contrast to previous studies reporting increased levels of Prevotella intermedia, a specific aim was to analyse phenotypically two identical species, P. intermedia and Prevotella nigrescens, separately using a 16S ribosomal DNA-based PCR. As a result, the increased levels of P. nigrescens were related to pregnancy gingivitis. Matrix metalloproteinases (MMPs) are involved in periodontal destruction. However, their role in pregnancy gingivitis is not well studied. Therefore, neutrophilic enzymes and proteinases, such as MMP and myeloperoxidase (MPO) levels were analysed from saliva and gingival crevicular fluid (GCF) samples during the follow-up. Despite increased inflammation and microbial shift towards anaerobes, the host response did not activate the MMP, elastase and MPO secretion during pregnancy. These results demonstrate that during pregnancy gingival inflammation is enhanced especially during the second trimester, when P. nigrescens levels in subgingival plaque were increased, whereas the neutrophilic enzymes and proteinase levels in both saliva and GCF remained low. These findings could explain, at least in part, why pregnancy gingivitis itself does not predispose or proceed to periodontitis.

Prediction of 3D structure and ligand-binding properties : ABC transporters and flavodiiron proteins from Synechocystis sp. strain PCC 6803

Cyanobacteria are unicellular, non-nitrogen-fixing prokaryotes, which perform photosynthesis similarly as higher plants. The cyanobacterium Synechocystis sp. strain PCC 6803 is used as a model organism in photosynthesis research. My research described herein aims at understanding the function of the photosynthetic machinery and how it responds to changes in the environment. Detailed knowledge of the regulation of photosynthesis in cyanobacteria can be utilized for biotechnological purposes, for example in the harnessing of solar energy for biofuel production. In photosynthesis, iron participates in electron transfer. Here, we focused on iron transport in Synechocystis sp. strain PCC 6803 and particularly on the environmental regulation of the genes encoding the FutA2BC ferric iron transporter, which belongs to the ABC transporter family. A homology model built for the ATP-binding subunit FutC indicates that it has a functional ATPbinding site as well as conserved interactions with the channel-forming subunit FutB in the transporter complex. Polyamines are important for the cell proliferation, differentiation and apoptosis in prokaryotic and eukaryotic cells. In plants, polyamines have special roles in stress response and in plant survival. The polyamine metabolism in cyanobacteria in response to environmental stress is of interest in research on stress tolerance of higher plants. In this thesis, the potd gene encoding an polyamine transporter subunit from Synechocystis sp. strain PCC 6803 was characterized for the first time. A homology model built for PotD protein indicated that it has capability of binding polyamines, with the preference for spermidine. Furthermore, in order to investigate the structural features of the substrate specificity, polyamines were docked into the binding site. Spermidine was positioned very similarly in Synechocystis PotD as in the template structure and had most favorable interactions of the docked polyamines. Based on the homology model, experimental work was conducted, which confirmed the binding preference. Flavodiiron proteins (Flv) are enzymes, which protect the cell against toxicity of oxygen and/or nitric oxide by reduction. In this thesis, we present a novel type of photoprotection mechanism in cyanobacteria by the heterodimer of Flv2/Flv4. The constructed homology model of Flv2/Flv4 suggests a functional heterodimer capable of rapid electron transfer. The unknown protein sll0218, encoded by the flv2-flv4 operon, is assumed to facilitate the interaction of the Flv2/Flv4 heterodimer and energy transfer between the phycobilisome and PSII. Flv2/Flv4 provides an alternative electron transfer pathway and functions as an electron sink in PSII electron transfer.

Modeling of residual stresses and distortion due to welding in fillet welds

Welding has a growing role in modern world manufacturing. Welding joints are extensively used from pipes to aerospace industries. Prediction of welding residual stresses and distortions is necessary for accurate evaluation of fillet welds in relation to design and safety conditions. Residual stresses may be beneficial or detrimental, depending whether they are tensile or compressive and the loading. They directly affect the fatigue life of the weld by impacting crack growth rate. Beside theoretical background of residual stresses this study calculates residual stresses and deformations due to localized heating by welding process and subsequent rapid cooling in fillet welds. Validated methods are required for this purpose due to complexity of process, localized heating, temperature dependence of material properties and heat source. In this research both empirical and simulation methods were used for the analysis of welded joints. Finite element simulation has become a popular tool of prediction of welding residual stresses and distortion. Three different cases with and without preload have been modeled during this study. Thermal heat load set is used by calculating heat flux from the given heat input energy. First the linear and then nonlinear material behavior model is modeled for calculation of residual stresses. Experimental work is done to calculate the stresses empirically. The results from both the methods are compared to check their reliability. Residual stresses can have a significant effect on fatigue performance of the welded joints made of high strength steel. Both initial residual stress state and subsequent residual stress relaxation need to be considered for accurate description of fatigue behavior. Tensile residual stresses are detrimental and will reduce the fatigue life and compressive residual stresses will increase it. The residual stresses follow the yield strength of base or filler material and the components made of high strength steel are typically thin, where the role of distortion is emphasizing.

Pituussuunnassa hitsatun rakenneputken väsymislujuus HF –hitsausta käytettäessä

Tässä diplomityössä määritettiin pituussuunnassa hitsatun rakenneputken väsymislujuus HF –hitsausta käytettäessä. Työn tavoitteena oli vertailla eri jälkikäsittelyjen ja kahden eri materiaalin vaikutusta väsymislujuuteen. Materiaaleina kokeissa oli Ruukki double grade ja Optim 700 Plus MH. Eurokoodi 3 ja IIW määrittelee kiinnityshitseille väsymiskestävyysluokaksi 125-140, kun SN -käyrän kaltevuus, m = 3. Koetuloksia vertailtiin näihin valmiiksi määriteltyihin väsymiskestävyysluokkiin. Ruukki Metals Oy toimitti koemateriaalin kahdenlaisia väsytyskokeita varten, joiden avulla väsymislujuus voitiin määrittää. Ensimmäinen koe suoritettiin värähtelyllä hyödyntäen rakenneputken ominaistaajuutta, jolloin kuormituksen rajajännityssuhde on -1. Toinen väsytyskoe suoritettiin rakenneputkista leikatuille väsytyssauvoille, missä pituussuuntainen HF –hitsi on keskellä sauvaa. Tämä väsytyskoe suoritettiin vetotykytyksellä rajajännityssuhteella 0,1. Väsytyskokeissa havaittiin, että kiinnityshitsi täyttää sille asetetut vaatimukset, koska murtumat tapahtuivat perusaineesta. Tällöin koetuloksia vertaillaan Eurokoodi 3:n perusaineen väsymisluokkaan 160, SN -käyrän kaltevuudella m = 5. Kaikkien koetulosten väsymiskestävyysluokan keskiarvoksi saatiin 185 95 %:n todennäköisyydellä. Tutkimuksessa saatiin arvokasta tietoa kahden eri materiaalin väsymislujuudesta. Materiaalilla ei kuitenkaan havaittu vaikutusta lujuuteen. Eri jälkikäsittelyt eli juuren puolen metallipurseen höyläys tai pituussuuntaisen hitsisauman hehkutus eivät vaikuttaneet väsymislujuuteen. Kokeissa väsymismurtuma ydintyi rakenneputken pinnalta olevista alkuvioista, joten putkien käsittelyä valmistuksen jälkeen voitaisiin parantaa.