The Detector Control Systems for the CMS Resistive Plate Chamber at LHC

The RPC Detector Control System (RCS) is the main subject of this PhD work. The project, involving the Lappeenranta University of Technology, the Warsaw University and INFN of Naples, is aimed to integrate the different subsystems for the RPC detector and its trigger chain in order to develop a common framework to control and monitoring the different parts. In this project, I have been strongly involved during the last three years on the hardware and software development, construction and commissioning as main responsible and coordinator. The CMS Resistive Plate Chambers (RPC) system consists of 912 double-gap chambers at its start-up in middle of 2008. A continuous control and monitoring of the detector, the trigger and all the ancillary sub-systems (high voltages, low voltages, environmental, gas, and cooling), is required to achieve the operational stability and reliability of a so large and complex detector and trigger system. Role of the RPC Detector Control System is to monitor the detector conditions and performance, control and monitor all subsystems related to RPC and their electronics and store all the information in a dedicated database, called Condition DB. Therefore the RPC DCS system has to assure the safe and correct operation of the sub-detectors during all CMS life time (more than 10 year), detect abnormal and harmful situations and take protective and automatic actions to minimize consequential damages. The analysis of the requirements and project challenges, the architecture design and its development as well as the calibration and commissioning phases represent themain tasks of the work developed for this PhD thesis. Different technologies, middleware and solutions has been studied and adopted in the design and development of the different components and a big challenging consisted in the integration of these different parts each other and in the general CMS control system and data acquisition framework. Therefore, the RCS installation and commissioning phase as well as its performance and the first results, obtained during the last three years CMS cosmic runs, will be

Comparison of Different Concentrated Solar Power Collector Designs and Development of a Linear Fresnel Solar Collector Model

Concentrated solar power (CSP) is a renewable energy technology, which could contribute to overcoming global problems related to pollution emissions and increasing energy demand. CSP utilizes solar irradiation, which is a variable source of energy. In order to utilize CSP technology in energy production and reliably operate a solar field including thermal energy storage system, dynamic simulation tools are needed in order to study the dynamics of the solar field, to optimize production and develop control systems. The object of this Master’s Thesis is to compare different concentrated solar power technologies and configure a dynamic solar field model of one selected CSP field design in the dynamic simulation program Apros, owned by VTT and Fortum. The configured model is based on German Novatec Solar’s linear Fresnel reflector design. Solar collector components including dimensions and performance calculation were developed, as well as a simple solar field control system. The preliminary simulation results of two simulation cases under clear sky conditions were good; the desired and stable superheated steam conditions were maintained in both cases, while, as expected, the amount of steam produced was reduced in the case having lower irradiation conditions. As a result of the model development process, it can be concluded, that the configured model is working successfully and that Apros is a very capable and flexible tool for configuring new solar field models and control systems and simulating solar field dynamic behaviour.

Jatkuvavaletun teräksen leikkaussuunnitelman optimointi

Teollisuuden tuotannon eri prosessien optimointi on hyvin ajankohtainen aihe. Monet ohjausjärjestelmät ovat ajalta, jolloin tietokoneiden laskentateho oli hyvin vaatimaton nykyisiin verrattuna. Työssä esitetään tuotantoprosessi, joka sisältää teräksen leikkaussuunnitelman muodostamisongelman. Valuprosessi on yksi teräksen valmistuksen välivaiheita. Siinä sopivaan laatuun saatettu sula teräs valetaan linjastoon, jossa se jähmettyy ja leikataan aihioiksi. Myöhemmissä vaiheissa teräsaihioista muokataan pienempiä kokonaisuuksia, tehtaan lopputuotteita. Jatkuvavaletut aihiot voidaan leikata tilauskannasta riippuen monella eri tavalla. Tätä varten tarvitaan leikkaussuunnitelma, jonka muodostamiseksi on ratkaistava sekalukuoptimointiongelma. Sekalukuoptimointiongelmat ovat optimoinnin haastavin muoto. Niitä on tutkittu yksinkertaisempiin optimointiongelmiin nähden vähän. Nykyisten tietokoneiden laskentateho on kuitenkin mahdollistanut raskaampien ja monimutkaisempien optimointialgoritmien käytön ja kehittämisen. Työssä on käytetty ja esitetty eräs stokastisen optimoinnin menetelmä, differentiaalievoluutioalgoritmi. Tässä työssä esitetään teräksen leikkausoptimointialgoritmi. Kehitetty optimointimenetelmä toimii dynaamisesti tehdasympäristössä käyttäjien määrittelemien parametrien mukaisesti. Työ on osa Syncron Tech Oy:n Ovako Bar Oy Ab:lle toimittamaa ohjausjärjestelmää.

Field Sales Management Control: Towards a Multi-Level Theory

The purpose of this dissertation is to increase the understanding and knowledge of field sales management control systems (i.e. sales managers monitoring, directing, evaluating and rewarding activities) and their potential consequences on salespeople. This topic is important because research conducted in the past has indicated that the choice of control system type can on the other hand have desirable consequences, such as high levels of motivation and performance, and on the other hand leadto harmful unintended consequences, such as opportunistic or unethical behaviors. Despite the fact that marketing and sales management control systems have been under rigorous research for over two decades, it still is at a very early stage of development, and several inconsistencies can be found in the research results. This dissertation argues that these inconsistencies are mainly derived from misspecification of the level of analysis in the past research. These different levels of analysis (i.e. strategic, tactical, and operational levels) involve very different decision-making situations regarding the control and motivation of sales force, which should be taken into consideration when conceptualizing the control. Moreover, the study of salesperson consequences of a field sales management control system is actually a cross-level phenomenon, which means that at least two levels of analysis are simultaneously involved. The results of this dissertation confirm the need to re-conceptualize the field sales management control system concept. It provides empirical evidence for the assertion that control should be conceptualized with more details atthe tactical/operational level of analysis than at the strategic levelof analysis. Moreover, the results show that some controls are more efficiently communicated to field salespeople than others. It is proposed that this difference is due to different purposes of control; some controls aredesigned for influencing salespersons' behavior (aim at motivating) whereas some controls are designed to aid decision-making (aim at providing information). According to the empirical results of this dissertation, the both types of controls have an impact to the sales force, but this impactis not as strong as expected. The results obtained in this dissertation shed some light to the nature of field sales management control systems, and their consequences on salespeopl

Hammashihnajohdeakseleiden liikkeiden synkronointi

Nykyisessä valmistusteollisuudessa erilaisten robottien ja automatisoitujen tuotantovaiheiden rooli on erittäin merkittävä. Tarkasti suunnitellut liikkeet ja toimintavaiheet voidaan nykyisillä järjestelmillä ajoittaa tarkasti toisiinsa nähden, jolloin erilaisten virhetilanteidenkin sattuessa järjestelmä pystyy toimimaan tilanteen edellyttämällä tavalla. Automatisoinnin etuna on myös tuotannon muokkaaminen erilaisten tuotteiden valmistamiseen pienillä muutoksilla, jolloin tuotantokustannukset pysyvät matalina myös pienten valmistuserien tapauksissa. Usean akselin laitteissa eli niin sanotuissa moniakselikäytöissä laitteen toimintatarkkuus riippuu jokaisen liikeakselin tarkkuudesta. Liikkeenohjauksessa on perinteisesti ollut käytössä myötäkytketty paikkakaskadi, jonka virityksessä otetaan huomioon akselilla olevat erilaiset dynaamiset tilat ja käytettävät referenssit. Monissa nykyisissä hajautetuissa järjestelmissä eli moniakselikäytöissä, joissa jokaiselle akselille on oma ohjauslaite, ei yksittäisen akselin paikkavirhettä huomioida muiden akseleiden ohjauksessa. Työssä tutkitaan erilaisia moniakselijärjestelmien ohjausmenetelmiä ja myötäkytketyn paikkakaskadin toimintaa moniakselikäytössä pyritään parantamaan tuomalla paikkasäätimen rinnalle toinen säädin, jonka tulona on akseleiden välinen paikkaero.

Modeling of electrolyte sorption – from phase equilibria to dynamic separation systems

In this thesis, general approach is devised to model electrolyte sorption from aqueous solutions on solid materials. Electrolyte sorption is often considered as unwanted phenomenon in ion exchange and its potential as an independent separation method has not been fully explored. The solid sorbents studied here are porous and non-porous organic or inorganic materials with or without specific functional groups attached on the solid matrix. Accordingly, the sorption mechanisms include physical adsorption, chemisorption on the functional groups and partition restricted by electrostatic or steric factors. The model is tested in four Cases Studies dealing with chelating adsorption of transition metal mixtures, physical adsorption of metal and metalloid complexes from chloride solutions, size exclusion of electrolytes in nano-porous materials and electrolyte exclusion of electrolyte/non-electrolyte mixtures. The model parameters are estimated using experimental data from equilibrium and batch kinetic measurements, and they are used to simulate actual single-column fixed-bed separations. Phase equilibrium between the solution and solid phases is described using thermodynamic Gibbs-Donnan model and various adsorption models depending on the properties of the sorbent. The 3-dimensional thermodynamic approach is used for volume sorption in gel-type ion exchangers and in nano-porous adsorbents, and satisfactory correlation is obtained provided that both mixing and exclusion effects are adequately taken into account. 2-Dimensional surface adsorption models are successfully applied to physical adsorption of complex species and to chelating adsorption of transition metal salts. In the latter case, comparison is also made with complex formation models. Results of the mass transport studies show that uptake rates even in a competitive high-affinity system can be described by constant diffusion coefficients, when the adsorbent structure and the phase equilibrium conditions are adequately included in the model. Furthermore, a simplified solution based on the linear driving force approximation and the shrinking-core model is developed for very non-linear adsorption systems. In each Case Study, the actual separation is carried out batch-wise in fixed-beds and the experimental data are simulated/correlated using the parameters derived from equilibrium and kinetic data. Good agreement between the calculated and experimental break-through curves is usually obtained indicating that the proposed approach is useful in systems, which at first sight are very different. For example, the important improvement in copper separation from concentrated zinc sulfate solution at elevated temperatures can be correctly predicted by the model. In some cases, however, re-adjustment of model parameters is needed due to e.g. high solution viscosity.

Business intelligence and management control

The purpose of this study is to explore the possibilities of utilizing business intelligence (BI)systems in management control (MC). The topic of this study is explored trough four researchquestions. Firstly, what kind of management control systems (MCS) use or could use the data and information enabled by the BI system? Secondly, how the BI system is or could be utilized? Thirdly, has BI system enabled new forms of control or changed old ones? The fourth and final research question is whether the BI system supports some forms of control that the literature has not thought of, or is the BI system not used for some forms of control the literature suggests it should be used? The study is conducted as an extensive case study. Three different organizations were interviewed for the study. For the theoretical basis of the study, central theories in the field of management control are introduced. The term business intelligence is discussed in detail and the mechanisms for governance of business intelligence are presented. A literature analysis of the uses of BI for management control is introduced. The theoretical part of the study ends in the construction of a framework for business intelligence in management control. In the empirical part of the study the case organizations, their BI systems, and the ways they utilize these systems for management control are presented. The main findings of the study are that BI systems can be utilized in the fields suggested in the literature, namely in planning, cybernetic, reward, boundary, and interactive control. The systems are used both as the data or information feeders and directly as the tools. Using BI systems has also enabled entirely new forms of control in the studied organizations, most significantly in the area of interactive control. They have also changed the old control systems by making the information more readily available to the whole organization. No evidence of the BI systems being used for forms of control that the literature had not suggested was found. The systems were mostly used for cybernetic control and interactive control, whereas the support for other types of control was not as prevalent. The main contribution of the study to the existing literature is the insight provided into how BI systems, both theoretically and empirically, are used for management control. The framework for business intelligence in management control presented in the study can also be utilized in further studies about the subject.

Adaptive control of Hydraulic Drive

Adaptive control systems are one of the most significant research directions of modern control theory. It is well known that every mechanical appliance’s behavior noticeably depends on environmental changes, functioning-mode parameter changes and changes in technical characteristics of internal functional devices. An adaptive controller involved in control process allows reducing an influence of such changes. In spite of this such type of control methods is applied seldom due to specifics of a controller designing. The work presented in this paper shows the design process of the adaptive controller built by Lyapunov’s function method for the Hydraulic Drive. The calculation needed and the modeling were conducting with MATLAB® software including Simulink® and Symbolic Math Toolbox™ etc. In the work there was applied the Jacobi matrix linearization of the object’s mathematical model and derivation of the suitable reference models based on Newton’s characteristic polynomial. The intelligent adaptive to nonlinearities algorithm for solving Lyapunov’s equation was developed. Developed algorithm works properly but considered plant is not met requirement of functioning with. The results showed confirmation that adaptive systems application significantly increases possibilities in use devices and might be used for correction a system’s behavior dynamics.

Agent-based management systems for many-core platforms : rigorous design and efficient implementation

Due to various advantages such as flexibility, scalability and updatability, software intensive systems are increasingly embedded in everyday life. The constantly growing number of functions executed by these systems requires a high level of performance from the underlying platform. The main approach to incrementing performance has been the increase of operating frequency of a chip. However, this has led to the problem of power dissipation, which has shifted the focus of research to parallel and distributed computing. Parallel many-core platforms can provide the required level of computational power along with low power consumption. On the one hand, this enables parallel execution of highly intensive applications. With their computational power, these platforms are likely to be used in various application domains: from home use electronics (e.g., video processing) to complex critical control systems. On the other hand, the utilization of the resources has to be efficient in terms of performance and power consumption. However, the high level of on-chip integration results in the increase of the probability of various faults and creation of hotspots leading to thermal problems. Additionally, radiation, which is frequent in space but becomes an issue also at the ground level, can cause transient faults. This can eventually induce a faulty execution of applications. Therefore, it is crucial to develop methods that enable efficient as well as resilient execution of applications. The main objective of the thesis is to propose an approach to design agentbased systems for many-core platforms in a rigorous manner. When designing such a system, we explore and integrate various dynamic reconfiguration mechanisms into agents functionality. The use of these mechanisms enhances resilience of the underlying platform whilst maintaining performance at an acceptable level. The design of the system proceeds according to a formal refinement approach which allows us to ensure correct behaviour of the system with respect to postulated properties. To enable analysis of the proposed system in terms of area overhead as well as performance, we explore an approach, where the developed rigorous models are transformed into a high-level implementation language. Specifically, we investigate methods for deriving fault-free implementations from these models into, e.g., a hardware description language, namely VHDL.

Underwater Remote Welding Technology for Offshore Structures

The construction of offshore structures, equipment and devices requires a high level of mechanical reliability in terms of strength, toughness and ductility. One major site for mechanical failure, the weld joint region, needs particularly careful examination, and weld joint quality has become a major focus of research in recent times. Underwater welding carried out offshore faces specific challenges affecting the mechanical reliability of constructions completed underwater. The focus of this thesis is on improvement of weld quality of underwater welding using control theory. This research work identifies ways of optimizing the welding process parameters of flux cored arc welding (FCAW) during underwater welding so as to achieve desired weld bead geometry when welding in a water environment. The weld bead geometry has no known linear relationship with the welding process parameters, which makes it difficult to determine a satisfactory weld quality. However, good weld bead geometry is achievable by controlling the welding process parameters. The doctoral dissertation comprises two sections. The first part introduces the topic of the research, discusses the mechanisms of underwater welding and examines the effect of the water environment on the weld quality of wet welding. The second part comprises four research papers examining different aspects of underwater wet welding and its control and optimization. Issues considered include the effects of welding process parameters on weld bead geometry, optimization of FCAW process parameters, and design of a control system for the purpose of achieving a desired bead geometry that can ensure a high level of mechanical reliability in welded joints of offshore structures. Artificial neural network systems and a fuzzy logic controller, which are incorporated in the control system design, and a hybrid of fuzzy and PID controllers are the major control dynamics used. This study contributes to knowledge of possible solutions for achieving similar high weld quality in underwater wet welding as found with welding in air. The study shows that carefully selected steels with very low carbon equivalent and proper control of the welding process parameters are essential in achieving good weld quality. The study provides a platform for further research in underwater welding. It promotes increased awareness of the need to improve the quality of underwater welding for offshore industries and thus minimize the risk of structural defects resulting from poor weld quality.

Power quality improving with virtual flux-based voltage source line converter

Line converters have become an attractive AC/DC power conversion solution in industrial applications. Line converters are based on controllable semiconductor switches, typically insulated gate bipolar transistors. Compared to the traditional diode bridge-based power converters line converters have many advantageous characteristics, including bidirectional power flow, controllable de-link voltage and power factor and sinusoidal line current. This thesis considers the control of the lineconverter and its application to power quality improving. The line converter control system studied is based on the virtual flux linkage orientation and the direct torque control (DTC) principle. A new DTC-based current control scheme is introduced and analyzed. The overmodulation characteristics of the DTC converter are considered and an analytical equation for the maximum modulation index is derived. The integration of the active filtering features to the line converter isconsidered. Three different active filtering methods are implemented. A frequency-domain method, which is based on selective harmonic sequence elimination, anda time-domain method, which is effective in a wider frequency band, are used inharmonic current compensation. Also, a voltage feedback active filtering method, which mitigates harmonic sequences of the grid voltage, is implemented. The frequency-domain and the voltage feedback active filtering control systems are analyzed and controllers are designed. The designs are verified with practical measurements. The performance and the characteristics of the implemented active filtering methods are compared and the effect of the L- and the LCL-type line filteris discussed. The importance of the correct grid impedance estimate in the voltage feedback active filter control system is discussed and a new measurement-based method to obtain it is proposed. Also, a power conditioning system (PCS) application of the line converter is considered. A new method for correcting the voltage unbalance of the PCS-fed island network is proposed and experimentally validated.

Pituusleikkurin turvaväylät ja koneturvallisuus

Turvallisuuteen liittyvän ohjausjärjestelmän tehtävänä on siirtää ja käsitellä turvallisuuskriittistä tietoa. Esimerkiksi anturin (turvalaitteen) havaitessa vaaravyöhykkeelle pyrkivän ihmisen tulee ensimmäisenä tiedon välittyä ohjausjärjestelmään. Ohjausjärjestelmän on muodostettava saapuneen tiedon perusteella käsky tehonohjauselimille. Tehonohjauselimillä säädellään koneen käyttöenergian syöttöä ja sitä kautta on mahdollista pysäyttää koneen liike ennen mahdollisen vahingon sattumista. Perinteiset turvaratkaisut ovat perustuneet pakkotoimintaisiin releisiin ja kahdennuksiin. Tällämenetelmällä on toteutettu varmatoimintaisia turvaratkaisuja, joissa yksittäiset viat ovat paljastuneet. Nykyisin on kuitenkin yhä enemmän tarvetta integroida turvatoiminnot automaatiojärjestelmään ja toteuttaa turvaratkaisut hajautetuillajärjestelmillä. Hajautetut järjestelmät sisältävät osittain ohjelmoitavien järjestelmien etuja ja haittoja, mutta tuovat mukanaan myös uudenlaisia vikoja. Työn tarkoitus oli selvittää, millaisia rajoituksia koneturvallisuus asettaa paperiteollisuuden pituusleikkurien turvallisuuteen liittyville ohjausjärjestelmille, sekä selvittää turvallisuuteen liittyvien järjestelmien rakennetta ja ominaisuuksia. Tässä työssä tutkittiin AS-i, EsaLan ja ProfiSafe turvajärjestelmiä teknisten tietojen perusteella. Tutkitut järjestelmät ovat erilaisia ja soveltuvat tämän vuoksi hieman erilaisiin kohteisiin. Kaikilla näillä järjestelmillä on kuitenkin mahdollista toteuttaa pituusleikkurin turvaväyläjärjestelmässä riittävä turvallisuuden taso koneturvallisuuden näkökulmasta. Tämä edellyttää oikein tehtyä riskianalyysiä ja oikeita suunnittelumenetelmiä. Teknisten tietojen perusteella otettiin testattavaksi AS-i safety at workja EsaLan:in Compact järjestelmät, joille suoritettiin sähkömagneettiseen yhteensopivuuteen (EMC) ja toiminnallisuuteen liittyviä testejä.

Laiteohjauksessamuodostuvan informaation jalostamisen mahdollisuudet

Teollisuuden automaatiojärjestelmät digitalisoituvat, samalla niiden tuottaman reaaliaikaisen datan määrä kasvaa ja etenkin sen saatavuus helpottuu. Samanaikaisesti laitevalmistajan liiketoimintamallit ovat muuttumassa perinteisestä konevalmistuksesta kohti palveluntarjontaa. Muuttuneessa tilanteessa laitteiden ohjauksessa käytettäviltä järjestelmiltä vaaditaan uusia ominaisuuksia. Informaation käsittely ja jalostaminen muodostuvat tärkeiksi kilpailu-tekijöiksi. Kirjallisuusosassa on tarkasteltu, miten data jalostuu informaatioksi ja siitä edelleen tietämykseksi. Työssä myös selvitetään, miten niitä voidaan hyödyntää liiketoiminnassa. Samalla perehdytään teollisuudesta löytyviin informaatio- ja tietämysjärjestelmiin. Kokeellisessa osassa esitellään toimiva tiedonkeruu- ja raportointijärjestelmä ja tutkitaan, miten sitä tulisi kehittää, jotta se sopisi paremmin muuttuviin liiketoimintamalleihin. Lopputuloksena kehitettiin mallijärjestelmä, jolla pystytään täyttämään laitevalmistajan ja loppukäyttäjän muuttuneet informaatiotarpeet osana laiteohjausta.

Kuorimon automaatiojärjestelmän optimointi

Työn tavoitteena oli pienentää kuorinnassa syntyviä puuhäviöitä ja parantaa linjan käytettävyyttä nykyaikaisella puunkuorimolla. Tavoitteet toteutettiin automaatiojärjestelmään tehdyillä muutoksilla. Rumpukuorintaprosessi on säilynyt pitkään samanlaisena. Viime vuosina on markkinoille tullut uusia älykkäitä mittalaitteita ja optimointiin kykeneviä säätöjärjestelmiä. Uudenlaisella automaatiotekniikalla on mahdollista mitata kuorintatulosta ja kuorinnassa syntyneitä puuhäviöitä reaaliaikaisesti. Laaduntarkkailun lisäksi tietoja hyödynnetään kuorintaprosessin automaattisessa ohjauksessa. Optimaalisen kuorintatuloksen saavuttaminen edellyttää virheetöntä automaation toimintaa ja tarkkaa viritystä säädöiltä. Työssä perehdyttiin kuorimon perusautomaatioon ja ylemmän tason säädön toimintaan. Prosessinohjauksessa havaitut ongelmakohdat korjattiin. Lopputuloksena saatiin vakiokuorintatehon malli, joka pienentää puuhäviöitä ja parantaa linjaston käytettävyyttä. Saaduilla tuloksilla on merkittävä taloudellinen arvo, ja menetelmät ovat hyödynnettävissä myös toisilla rumpukuorimoilla.