Konepajatekniikan laboratorion turvallisuussuunnitelma

Diplomityön tavoitteena oli tutkia LTY:n Konepajatekniikan laboratorion työturvallisuutta sekä laatia seurantalomake ja tehdä turvallisuusohjeet Konepajatekniikan laboratorioon. Konepajatekniikan laboratorioon ollaan rakentamassa uutta FM-järjestelmää, jonka turvallisuusriskejä ja vaaroja kartoitettiin etukäteen saatavilla olevan materiaalin avulla. Näin Konepajatekniikan laboratorio varautuu etukäteen FM-järjestelmän käyttöön liittyviin työturvallisuusasioihin. Diplomityön aikana seurasimme Konepajatekniikan laboratorion työturvallisuutta ja tapaturmien määrää seurantaomakkeen avulla. Samalla Konepajatekniikan laboratorioon tehtiin turvallisuusohjeet, joilla pyritään ennaltaehkäisemään työtapaturmien syntymistä. Konepajatekniikan laboratorion työturvallisuustasossa ja työtapaturma määrissä ei näyttäisi olevan poikkeavaa verrattuna koko Suomen konepaja-alan työturvallisuustasoon. Havaintojakson lyhyys alentaa johtopäätöksien luotettavuutta. Työturvallisuuden kehittämistä ja ennaltaehkäisevää työtä tulee tehdä jatkuvasti.

A study of combustion phenomena in circulating fluidized beds by developing and applying experimental and modelling methods for laboratory-scale reactors

The results shown in this thesis are based on selected publications of the 2000s decade. The work was carried out in several national and EC funded public research projects and in close cooperation with industrial partners. The main objective of the thesis was to study and quantify the most important phenomena of circulating fluidized bed combustors by developing and applying proper experimental and modelling methods using laboratory scale equipments. An understanding of the phenomena plays an essential role in the development of combustion and emission performance, and the availability and controls of CFB boilers. Experimental procedures to study fuel combustion behaviour under CFB conditions are presented in the thesis. Steady state and dynamic measurements under well controlled conditions were carried out to produce the data needed for the development of high efficiency, utility scale CFB technology. The importance of combustion control and furnace dynamics is emphasized when CFB boilers are scaled up with a once through steam cycle. Qualitative information on fuel combustion characteristics was obtained directly by comparing flue gas oxygen responses during the impulse change experiments with fuel feed. A one-dimensional, time dependent model was developed to analyse the measurement data Emission formation was studied combined with fuel combustion behaviour. Correlations were developed for NO, N2O, CO and char loading, as a function of temperature and oxygen concentration in the bed area. An online method to characterize char loading under CFB conditions was developed and validated with the pilot scale CFB tests. Finally, a new method to control air and fuel feeds in CFB combustion was introduced. The method is based on models and an analysis of the fluctuation of the flue gas oxygen concentration. The effect of high oxygen concentrations on fuel combustion behaviour was also studied to evaluate the potential of CFB boilers to apply oxygenfiring technology to CCS. In future studies, it will be necessary to go through the whole scale up chain from laboratory phenomena devices through pilot scale test rigs to large scale, commercial boilers in order to validate the applicability and scalability of the, results. This thesis shows the chain between the laboratory scale phenomena test rig (bench scale) and the CFB process test rig (pilot). CFB technology has been scaled up successfully from an industrial scale to a utility scale during the last decade. The work shown in the thesis, for its part, has supported the development by producing new detailed information on combustion under CFB conditions.

Poster presentation as a report of a self-designed laboratory experiment : a case study

Julkaisumaa: 203 CZ CZE Tšekki

Improving the competitiveness of electrolytic Zinc process by chemical reaction engineering approach

This doctoral thesis describes the development work performed on the leachand purification sections in the electrolytic zinc plant in Kokkola to increase the efficiency in these two stages, and thus the competitiveness of the plant. Since metallic zinc is a typical bulk product, the improvement of the competitiveness of a plant was mostly an issue of decreasing unit costs. The problems in the leaching were low recovery of valuable metals from raw materials, and that the available technology offered complicated and expensive processes to overcome this problem. In the purification, the main problem was consumption of zinc powder - up to four to six times the stoichiometric demand. This reduced the capacity of the plant as this zinc is re-circulated through the electrolysis, which is the absolute bottleneck in a zinc plant. Low selectivity gave low-grade and low-value precipitates for further processing to metallic copper, cadmium, cobalt and nickel. Knowledge of the underlying chemistry was poor and process interruptions causing losses of zinc production were frequent. Studies on leaching comprised the kinetics of ferrite leaching and jarosite precipitation, as well as the stability of jarosite in acidic plant solutions. A breakthrough came with the finding that jarosite could precipitate under conditions where ferrite would leach satisfactorily. Based on this discovery, a one-step process for the treatment of ferrite was developed. In the plant, the new process almost doubled the recovery of zinc from ferrite in the same equipment as the two-step jarosite process was operated in at that time. In a later expansion of the plant, investment savings were substantial compared to other technologies available. In the solution purification, the key finding was that Co, Ni, and Cu formed specific arsenides in the “hot arsenic zinc dust” step. This was utilized for the development of a three-step purification stage based on fluidized bed technology in all three steps, i.e. removal of Cu, Co and Cd. Both precipitation rates and selectivity increased, which strongly decreased the zinc powder consumption through a substantially suppressed hydrogen gas evolution. Better selectivity improved the value of the precipitates: cadmium, which caused environmental problems in the copper smelter, was reduced from 1-3% reported normally down to 0.05 %, and a cobalt cake with 15 % Co was easily produced in laboratory experiments in the cobalt removal. The zinc powder consumption in the plant for a solution containing Cu, Co, Ni and Cd (1000, 25, 30 and 350 mg/l, respectively), was around 1.8 g/l; i.e. only 1.4 times the stoichiometric demand – or, about 60% saving in powder consumption. Two processes for direct leaching of the concentrate under atmospheric conditions were developed, one of which was implemented in the Kokkola zinc plant. Compared to the existing pressure leach technology, savings were obtained mostly in investment. The scientific basis for the most important processes and process improvements is given in the doctoral thesis. This includes mathematical modeling and thermodynamic evaluation of experimental results and hypotheses developed. Five of the processes developed in this research and development program were implemented in the plant and are still operated. Even though these processes were developed with the focus on the plant in Kokkola, they can also be implemented at low cost in most of the zinc plants globally, and have thus a great significance in the development of the electrolytic zinc process in general.

The Russian National Innovation System - an International Perspective

Russia inherited a large research and development (R&D) sector from the Soviet times, and has retained a substantial R&D sector today, compared with other emerging economies. However, Russia is falling behind in all indicators measuring innovative output in comparison with most developed countries. Russia’s innovation performance is disappointing, despite the available stock of human capital and overall investment in R&D. The communist legacy still influences the main actors of the innovation system. The federal state is still the most important funding source for R&D. Private companies are not investing in innovative activities, preferring to “import” innovations embedded in foreign technologies. Universities are outsiders in the innovation system, only a few universities carry out research activities. Nowadays, Russia is a resource-depended country. The economy depends on energy and metals for growth. The Russian economy faces the challenge of diversification and should embrace innovation, and shift to a knowledge economy to remain competitive in the long run. Therefore, Russia has to tackle the challenge of developing an efficient innovation system with its huge potential in science expertise and engineering know-how.