High pressure compression of filter cakes

The purpose of this thesis was to investigate the compression of filter cakes at high filtration pressures with five different test materials and to compare the energy consumption of high pressure compression with the energy consumption of thermal drying. The secondary target of this study was to investigate the particle deformation of test materials during filtration and compression. Literature part consists of basic theory of filtration and compression and of the basic parameters that influence the filtration process. There is also a brief description about all of the test materials including their properties and their industrial production and processing. Theoretical equations for calculating the energy consumptions of the filtrations at different conditions are also presented. At the beginning of the experiments at experimental part, the basic filtration tests were done with all the five test materials. Filtration tests were made at eight different pressures, from 6 bars up to 100 bars, by using piston press pressure filter. Filtration tests were then repeated by using a cylinder with smaller slurry volume than in the first series of filtration tests. Separate filtration tests were also done for investigating the deformation of solid particles during filtration and for finding the optimal curve for raising the filtration pressure. Energy consumption differences between high pressure filtration and ideal thermal drying process were done partly experimentally and partly by using theoretical calculation equations. By comparing these two water removal methods, the optimal ranges for their use were found considering their energy efficiency. The results of the measurements shows that the filtration rate increased and the moisture content of the filter cakes decreased as the filtration pressure was increased. Also the porosity of the filter cakes mainly decreased when the filtration pressure was increased. Particle deformation during the filtration was observed only with coal particles.

Modeling of high pressure pretreatment process for gold leaching

Investigation of high pressure pretreatment process for gold leaching is the objective of the present master's thesis. The gold ores and concentrates which cannot be easily treated by leaching process are called "refractory". These types of ores or concentrates often have high content of sulfur and arsenic that renders the precious metal inaccessible to the leaching agents. Since the refractory ores in gold manufacturing industry take a considerable share, the pressure oxidation method (autoclave method) is considered as one of the possible ways to overcome the related problems. Mathematical modeling is the main approach in this thesis which was used for investigation of high pressure oxidation process. For this task, available information from literature concerning this phenomenon, including chemistry, mass transfer and kinetics, reaction conditions, applied apparatus and application, was collected and studied. The modeling part includes investigation of pyrite oxidation kinetics in order to create a descriptive mathematical model. The following major steps are completed: creation of process model by using the available knowledge; estimation of unknown parameters and determination of goodness of the fit; study of the reliability of the model and its parameters.

Computational modelling of non-equilibrium condensing steam flows in low-pressure steam turbines

The steam turbines play a significant role in global power generation. Especially, research on low pressure (LP) steam turbine stages is of special importance for steam turbine man- ufactures, vendors, power plant owners and the scientific community due to their lower efficiency than the high pressure steam turbine stages. Because of condensation, the last stages of LP turbine experience irreversible thermodynamic losses, aerodynamic losses and erosion in turbine blades. Additionally, an LP steam turbine requires maintenance due to moisture generation, and therefore, it is also affecting on the turbine reliability. Therefore, the design of energy efficient LP steam turbines requires a comprehensive analysis of condensation phenomena and corresponding losses occurring in the steam tur- bine either by experiments or with numerical simulations. The aim of the present work is to apply computational fluid dynamics (CFD) to enhance the existing knowledge and understanding of condensing steam flows and loss mechanisms that occur due to the irre- versible heat and mass transfer during the condensation process in an LP steam turbine. Throughout this work, two commercial CFD codes were used to model non-equilibrium condensing steam flows. The Eulerian-Eulerian approach was utilised in which the mix- ture of vapour and liquid phases was solved by Reynolds-averaged Navier-Stokes equa- tions. The nucleation process was modelled with the classical nucleation theory, and two different droplet growth models were used to predict the droplet growth rate. The flow turbulence was solved by employing the standard k-ε and the shear stress transport k-ω turbulence models. Further, both models were modified and implemented in the CFD codes. The thermodynamic properties of vapour and liquid phases were evaluated with real gas models. In this thesis, various topics, namely the influence of real gas properties, turbulence mod- elling, unsteadiness and the blade trailing edge shape on wet-steam flows, are studied with different convergent-divergent nozzles, turbine stator cascade and 3D turbine stator-rotor stage. The simulated results of this study were evaluated and discussed together with the available experimental data in the literature. The grid independence study revealed that an adequate grid size is required to capture correct trends of condensation phenomena in LP turbine flows. The study shows that accurate real gas properties are important for the precise modelling of non-equilibrium condensing steam flows. The turbulence modelling revealed that the flow expansion and subsequently the rate of formation of liquid droplet nuclei and its growth process were affected by the turbulence modelling. The losses were rather sensitive to turbulence modelling as well. Based on the presented results, it could be observed that the correct computational prediction of wet-steam flows in the LP turbine requires the turbulence to be modelled accurately. The trailing edge shape of the LP turbine blades influenced the liquid droplet formulation, distribution and sizes, and loss generation. The study shows that the semicircular trailing edge shape predicted the smallest droplet sizes. The square trailing edge shape estimated greater losses. The analysis of steady and unsteady calculations of wet-steam flow exhibited that in unsteady simulations, the interaction of wakes in the rotor blade row affected the flow field. The flow unsteadiness influenced the nucleation and droplet growth processes due to the fluctuation in the Wilson point.

Korkeapainehöyryputkiston kannakoinnin muutostyön tuotteistaminen

Teollisuusyritysten kunnossapitostrategioiden muuttuessa enemmän ennakoivan kunnossapidon suuntaan, avaase teollisuuspalveluille uusia mahdollisuuksia. Nykyisin yksi menestyvän yrityksen lähtökohdista on kehittää tuotettaan asiakaslähtöisesti. Yrityksen täytyy luoda toimintatapoja, joilla tietoa asiakkaiden tarpeista pystytään keräämään. Työssä käsitellään asiakastarvekartoituksen vaiheet korkeapainehöyryputkiston muutosyön kehittämistä varten. asiakastarvekartoitukseen valitaan menetelmät niin tiedon hankintaa kuin analysointia varten. Asiakastarvekartoituksessa ei huomioida ainoastaan asiakasta, vaan siinä huomioidaan myös yrityksen itsensä sekä muiden osapuolten, kuten viranomaisten, vaikutus tuotteeseen. Asiakastarvekartoituksen avulla saadaan muutostyölle asetettua konkreettisia tavoitteita, sekä kehitettyä ratkaisuja, joiden avulla asiakasta pystytään palvelemaan entistä paremmin.

Paineilmajärjestelmän ja -hankinnan kehittäminen sementtitehtaalla

Työn tavoitteena oli kartoittaa Lappeenrannan sementtitehtaan paineilmajärjestelmä, tehdä järjestelmän kehittämissuunnitelma ja arvioida suunnitelman mukaisen investoinnin kannattavuus investointilaskelmilla. Kartoituksesta selviää paineilman hankinnan toteutus, järjestelmään kuuluvien laitteiden selvitys ja energiankulutus sekä jakeluverkon ja paineilman käytön kartoitus. Kartoituksen ja aineiston pohjalta laadittiin suunnitelma järjestelmän kehittämiseksi. Aineistoa kerättiin haastattelemalla laitetoimittajia sekä muiden sementtitehtaiden johtoa. Paineilman käyttöä tehostettiin ja tehtaan matalapaine- eli kuumailmaverkon osalta tehtiin suunnitelmat sen täydellisestä uusimisesta. Tehtaan korkeapaine- eli yleisilmaverkkoon päätettiin olla investoimatta työssä esiteltävien käytännön syiden vuoksi. Investoinnin taloudellinen kannattavuus arvioitiin työhön rakennetulla investointilaskentamallilla. Sen avulla laskettiin investoinnin kannattavuus annuiteettimenetelmällä. Laskelmien tulokseen liittyvä epävarmuus arvioitiin myös malliin rakennetulla herkkyysanalyysillä. Lisäksi mallilla vertailtiin investoinnin eri hankintavaihtoehtojen kannattavuutta. Investointi osoittautui kannattavaksi.

CO2-laserin soveltaminen WFU-paperin reunan leikkaamiseen

Tämän diplomityön tarkoitus oli selvittää CO2-laserin soveltuvuutta paperin reunan leikkaamiseen ennen liimapuristinta nopealle modernilleWFU-paperikoneelle. Merkittävimmät leikkauskokeet tehtiin leikkaamalla paperirataa todenmukaisissa olosuhteissa koekoneella. Koeleikkauksissa tutkittiin myös päällystettyjen paperilajien CO2-laserleikkausta. Paperin reunan koeleikkauksia suoritettiin leikkauspöytää vasten sekä telaa vasten. Leikkauspöytänä käytettiin korkeapainevesileikkaimelle suunniteltua leikkauspöytää, jota paranneltiin tämän työn yhteydessä paremmin laserleikkaukselle sopivaksi. Telaa vasten suoritetuilla leikkauksilla lasertehon tarve oli suurempi verrattuna pöytää vasten leikkaukseen samalla leikkausnopeudella ja samalla paperilajilla. Laserlaitteiston mitoittaminen oikein pelkkien arkkileikkauskokeiden perusteella ei ollut mahdollista. Myös rullilla tapahtuvia leikkauskokeita tarvittiin. Pöytää vasten tapahtuvaan leikkaamiseen tarvitaan 1000 W laserlaite paperin molemmille reunoille. Tämän tehoiset laserlaitteet riittävät kaikille Changshun PK 1:n paperilajeille niiden lajikohtaiseen maksimiajonopeuteen. Testatuista kolmesta polttovälistä antoi 5" polttoväli parhaat leikkaustulokset. Polttopisteen paikka voi vaihdella ± 0.75 mm paperin pinnasta vaikuttamatta silti merkittävästi lasertehon tarpeeseen. Laserleikatun paperin reuna oli hyvälaatuinen, eikä laserleikkaus aiheuttanut paperille epätoivottuja asioita kuten mustumista.

Development of filter media treatments for liquid filtration

Woven monofilament, multifilament, and spun yarn filter media have long been the standard media in liquid filtration equipment. While the energy for a solid-liquid separation process is determined by the engineering work, it is the interface between the slurry and the equipment - the filter media - that greatly affects the performance characteristics of the unit operation. Those skilled in the art are well aware that a poorly designed filter medium may endanger the whole operation, whereas well-performing filter media can make the operation smooth and economical. As the mineral and pulp producers seek to produce ever finer and more refined fractions of their products, it is becoming increasingly important to be able to dewater slurries with average particle sizes around 1 ¿m using conventional, high-capacity filtration equipment. Furthermore, the surface properties of the media must not allow sticky and adhesive particles to adhere to the media. The aim of this thesis was to test how the dirt-repellency, electrical resistance and highpressure filtration performance of selected woven filter media can be improved by modifying the fabric or yarn with coating, chemical treatment and calendering. The results achieved by chemical surface treatments clearly show that the woven media surface properties can be modified to achieve lower electrical resistance and improved dirt-repellency. The main challenge with the chemical treatments is the abrasion resistance and, while the experimental results indicate that the treatment is sufficiently permanent to resist standard weathering conditions, they may still prove to be inadequately strong in terms of actual use.From the pressure filtration studies in this work, it seems obvious that the conventional woven multifilament fabrics still perform surprisingly well against the coated media in terms of filtrate clarity and cake build-up. Especially in cases where the feed slurry concentration was low and the pressures moderate, the conventional media seemed to outperform the coated media. In the cases where thefeed slurry concentration was high, the tightly woven media performed well against the monofilament reference fabrics, but seemed to do worse than some of the coated media. This result is somewhat surprising in that the high initial specific resistance of the coated media would suggest that the media will blind more easily than the plain woven media. The results indicate, however, that it is actually the woven media that gradually clogs during the coarse of filtration. In conclusion, it seems obvious that there is a pressure limit above which the woven media looses its capacity to keep the solid particles from penetrating the structure. This finding suggests that for extreme pressures the only foreseeable solution is the coated fabrics supported by a strong enough woven fabric to hold thestructure together. Having said that, the high pressure filtration process seems to follow somewhat different laws than the more conventional processes. Based on the results, it may well be that the role of the cloth is most of all to support the cake, and the main performance-determining factor is a long life time. Measuring the pore size distribution with a commercially available porometer gives a fairly accurate picture of the pore size distribution of a fabric, but failsto give insight into which of the pore sizes is the most important in determining the flow through the fabric. Historically air, and sometimes water, permeability measures have been the standard in evaluating media filtration performance including particle retention. Permeability, however, is a function of a multitudeof variables and does not directly allow the estimation of the effective pore size. In this study a new method for estimating the effective pore size and open pore area in a densely woven multifilament fabric was developed. The method combines a simplified equation of the electrical resistance of fabric with the Hagen-Poiseuille flow equation to estimate the effective pore size of a fabric and the total open area of pores. The results are validated by comparison to the measured values of the largest pore size (Bubble point) and the average pore size. The results show good correlation with measured values. However, the measured and estimated values tend to diverge in high weft density fabrics. This phenomenon is thought to be a result of a more tortuous flow path of denser fabrics, and could most probably be cured by using another value for the tortuosity factor.

Ydinvoimalaitoksen turbiinilaitoksen toiminnan ja kunnonvalvonnan nykytilan kuvaus ja kehittämismahdollisuuksien kartoitus sekä toteutus ja kannattavuusarviointi

Työssä selvitettiin Olkiluodon ydinvoimalaitoksen prosessiseurannassa nykyisin käytössä olevia järjestelmiä sekä tutkittiin prosessisimulointiohjelman käyttömahdollisuuksia osana prosessiseurantaa. Ensisijaisesti tutkittiin kuinka hyvin simulointimalli soveltuu pienien tehopoikkeamien havainnoimiseen. Simulointimalli rakennettiin Endat Oy:n kehittämällä Prosim-simulointiohjelmalla. Simulointimalli on tehty kahdelle eri prosessille. Erilliset mallit rakennettiin sekä vuoden 2003 vuosihuoltoa edeltäneelle prosessille, että vuosihuollossa lauhteen esilämmityksen osalta muutetulle prosessille. Simulointimallien toimintaa käytännössä testattiin suorittamalla simulointiajoja muutamilla prosessin muutostilanteilla ja vertailemalla muutostilanteiden mittapistedataa simulointiohjelman laskemiin tuloksiin. Simulointimallin suurimmat poikkeamat mittapistedataan verrattuna todettiin turbiinilaitoksen korkeapainepuolella sekä lauhduttimessa. Käytännössä havaittiin, että nämä poikkeamat hankaloittavat simulointiohjelman käyttöä käytönvalvonnan työkaluna, eikä sen käytöstä näin ollen saada varsinaista lisäarvoa.

Nesteseosten liukoisuuksien mittaaminen

Diplomityön tarkoituksena on tarkastella isobuteenin dimeroitumisprosessin neste-nestetasapainoja. Tavoitteena on määrittää prosessissa esiintyvien komponenttien väliset neste-nestetasapainot. Työn kirjallisuusosassa on tarkasteltu neste-nestetasapainojen teoriaa. Erityisesti on tarkasteltu mittausmenetelmiä sekä kirjallisuudesta löytyneitä laitteistoja binääristen ja ternääristen systeemien neste-nestetasapainojen määritystä varten. Menetelmät ja laitteistot on esitetty erikseen matalassa ja korkeassa paineessa suoritettaville mittauksille. Lisäksi on tarkasteltu näytteenottoa sekä näytteiden analysointimenetelmiä. Kirjallisuusosassa on myös sivuttu kaasu-neste-nestetasapainojen määritystä, mutta työn varsinainen kohde on neste-nestetasapainojen määritys. Työn kokeellisessa osassa määritettiin iso-oktaaniprosessissa esiintyvien komponenttien välisiä binäärisiä ja ternäärisiä neste-nestetasapainoja. Mitattavien komponenttiparien määrää karsittiin ja jäljellejääneiden parien välillä suoritettavat mittaukset jaoteltiin matalassa ja korkeassa paineessa suoritettaviin määrityksiin. Ternääriset mittaukset tulivat kyseeseen sellaisten komponenttiparien kohdalla, joissa toisiinsa täysin liukenevien nesteiden systeemiin kolmatta komponenttia lisättäessä saatiin aikaiseksi kaksi nestefaasia. Tällaisesta mittaustiedosta voidaan määrittää neste-nestetasapainomallien parametrejä. Mittausten lisäksi kokeellisessa osassa tarkasteltiin näytteenottoa sekä näytteiden analysointia.

Balanced Scorecard kevytmetallivalimossa

Työn tavoitteena oli kehittää alihankintaosia valmistavalle kevytmetallivalimolle Balanced Scorecard - malliin pohjautuva suorituskyvyn mittausjärjestelmä. Mittariston tarkoituksena on kasvattaa yritysjohdon tietämystä yrityksen eri toimintojen suorituskyvystä ja tarjota informaatiota päätöksenteon tueksi. Tarve suorituskyvyn mittaamiselle on syntynyt yrityksen kasvaessa ja asiakaspohjan laajentuessa. Työn alussa tutkittiin kirjallisuutta liittyen suorituskyvyn mittaamiseen. Tämän jälkeen tutkittiin strategiatyötä Balanced Scorecard – projektin yhteydessä ja itse Balanced Scorecard – projektiin liittyviä kysymyksiä. Teoriatiedon pohjalta muodostettiin kohdeyrityksen Balanced Scorecard. Ensin täsmennettiin yrityksen visiota ja strategiaa hyvän mittariston luomiseksi. Mittarit valittiin pohjautuen kriittisiin menestystekijöihin ja ne sijoitettiin näkökulmiin, jotka ovat sisäisten prosessien näkökulma, asiakasnäkökulma, talousnäkökulma sekä kasvun ja kehityksen näkökulma. Sisäisten prosessien näkökulmaan sijoitettiin tuotekohtaisia, osastokohtaisia ja toimittajakohtaisia mittareita. Mittaristo ei suinkaan ole projektin päätyttyä valmis vaan sitä tulee kehittää jatkuvasti. Mittariston käyttöönotto avaa mahdollisuuksia niin toiminnanohjausjärjestelmän paremmalle hyödyntämiselle kuin tavoitehinnoittelun käyttöönotolle. Myös asiakaskannattavuuslaskennan käyttöönottoa tulevaisuudessa kannattaa harkita.

Prosessihyötysuhteen parantamiskohteiden kartoitus painevesireaktorityyppisessä ydinvoimalaitoksessa

Työn tavoitteena on kartoittaa painevesireaktorityyppisen ydinvoimalaitoksen prosessihyötysuhteen parantamiskohteita. Aluksi kirjallisuudesta etsitään hyötysuhteen parantamiskeinoja ideaalisessa höyryvoimalaitosprosessissa. Näistä valitaan sopivimmat tarkastelun kohteeksi todellisessa voimalaitoksessa: syöttöveden esilämmityksen tehostaminen väliottohöyryvirtausta kasvattamalla ja syöttöveden esilämmittimen lämmönsiirtopintaa lisäämällä. Tarkastelussa pyritään löytämään paras mahdollinen hyötysuhde väliottohöyrylinjojen putkikokoa sekä esilämmittimien putkien lukumäärää muuttamalla. Diskreetin optimoinnin iteraatioaskel määritetään hyötysuhteen osittaisderivaattojen avulla. Tehtäviä muutoksia simuloidaan APROS-simulointiohjelmalla, jossa käytetään Loviisan voimalaitoksesta tehtyä mallia VVER-440. Työssä havaittiin, että pelkkiä väliottohöyrylinjojen putkikokoja – ja massavirtaa – kasvattamalla Loviisan voimalaitoksen hyötysuhdetta voidaan parantaa parhaimmillaan 32,75%:sta 32,85%:iin. Syöttöveden esilämmittimien lämmönsiirtopintaa lisäämällä saadaan suurempi parannus hyötysuhteeseen: 32,75%:sta 32,99%:iin. Näissä tapauksissa muutettiin kaikkia väliottohöyrylinjoja tai syöttöveden esilämmittimien lämpöpintoja. Työssä tarkasteltiin myös joitakin pienempiä muutoskohteita, joista paras hyötysuhteen kasvu saatiin korkeapaine-esilämmittimien lämmönsiirtopintaa kasvattamalla sekä toisen väliottohöyrylinjan (RD12) ja sitä vastaavan syöttöveden esilämmittimen muutosten yhteisvaikutuksena.

Regenerated cellulose ultrafiltration membranes in the treatment of pulp and paper mill process waters

Ultrafiltration (UF) is widely applied in different separation processes in the pulp and paper industry. The growing need to protect the environment, a lack of pure water and an interest in producing high-value chemicals from compounds present in process waters will probably lead to an increase in the use of UF in the pulp and paper industry. The efficiency and cost-effectiveness of a UF process depends on the applied membrane. The membrane should have a high and stable filtration capacity, a particular selectivity and a long operational lifetime. To meet these requirements a membrane should have a low fouling tendency. In addition, it should withstand the prevailing operational and chemical conditions. This thesis evaluates the performance and applicability of the regenerated cellulose (RC) membranes 00030T and C2 in the treatment of pulp and paper mill process waters based on the requirements above. The results demonstrated that both the tested RC membranes fulfilled well the requirement of high filtration capacity. In addition, in the filtration of a paper mill clear filtrate (CF) the RC membranes were not as greatly affected by variations in the CF quality as a polysulphone membrane. Furthermore, due to their extreme hydrophilicity and weak charge the fouling tendency of the membranes can be expected to be low in pulp and paper mill filtration applications. It is, however, known that fouling cannot be totally avoided even when the membrane is chosen very carefully. This study indicated that carbohydrates influenced negatively on permeability and caused fouling in the filtration of groundwood mill circulation water. Thus, a pre-treatment effectively reducing the amount of carbohydrates might help to maintain a stable capacity. However, the results of the thesis also showed that the removal of some of the possible foulants might just increase the harmful effect of others. Multivariate examination was useful in the understanding of the complicated factors causing the unstable capacity. The thesis also revealed that the 00030T and C2 membranes can be used at high pressure (max. tested pressure 12 bar). The C2 membrane, having a sponge-like substructure, was more pressure resistant, and its performance was more stable at high pressure compared to the UCO30T membrane containing macrovoids in its substructure. Both tested membranes can, according to the results, also be used at temperatures as high as 70°C in acidic, neutral and alkaline conditions. However, the use at extreme conditions might cause faster ageing of the membranes compared to ageing in neutral conditions. The thesis proved that both the tested RC membranes are very suitable for pulp and paper mill applications and that the membranes can be utilised in processes operating in challenging conditions. Thus, they could be used in more demanding applications than supposed earlier.

Modeling the transport phenomena within arterial wall: porous media approach

The transport of macromolecules, such as low-density lipoprotein (LDL), and their accumulation in the layers of the arterial wall play a critical role in the creation and development of atherosclerosis. Atherosclerosis is a disease of large arteries e.g., the aorta, coronary, carotid, and other proximal arteries that involves a distinctive accumulation of LDL and other lipid-bearing materials in the arterial wall. Over time, plaque hardens and narrows the arteries. The flow of oxygen-rich blood to organs and other parts of the body is reduced. This can lead to serious problems, including heart attack, stroke, or even death. It has been proven that the accumulation of macromolecules in the arterial wall depends not only on the ease with which materials enter the wall, but also on the hindrance to the passage of materials out of the wall posed by underlying layers. Therefore, attention was drawn to the fact that the wall structure of large arteries is different than other vessels which are disease-resistant. Atherosclerosis tends to be localized in regions of curvature and branching in arteries where fluid shear stress (shear rate) and other fluid mechanical characteristics deviate from their normal spatial and temporal distribution patterns in straight vessels. On the other hand, the smooth muscle cells (SMCs) residing in the media layer of the arterial wall respond to mechanical stimuli, such as shear stress. Shear stress may affect SMC proliferation and migration from the media layer to intima. This occurs in atherosclerosis and intimal hyperplasia. The study of blood flow and other body fluids and of heat transport through the arterial wall is one of the advanced applications of porous media in recent years. The arterial wall may be modeled in both macroscopic (as a continuous porous medium) and microscopic scales (as a heterogeneous porous medium). In the present study, the governing equations of mass, heat and momentum transport have been solved for different species and interstitial fluid within the arterial wall by means of computational fluid dynamics (CFD). Simulation models are based on the finite element (FE) and finite volume (FV) methods. The wall structure has been modeled by assuming the wall layers as porous media with different properties. In order to study the heat transport through human tissues, the simulations have been carried out for a non-homogeneous model of porous media. The tissue is composed of blood vessels, cells, and an interstitium. The interstitium consists of interstitial fluid and extracellular fibers. Numerical simulations are performed in a two-dimensional (2D) model to realize the effect of the shape and configuration of the discrete phase on the convective and conductive features of heat transfer, e.g. the interstitium of biological tissues. On the other hand, the governing equations of momentum and mass transport have been solved in the heterogeneous porous media model of the media layer, which has a major role in the transport and accumulation of solutes across the arterial wall. The transport of Adenosine 5´-triphosphate (ATP) is simulated across the media layer as a benchmark to observe how SMCs affect on the species mass transport. In addition, the transport of interstitial fluid has been simulated while the deformation of the media layer (due to high blood pressure) and its constituents such as SMCs are also involved in the model. In this context, the effect of pressure variation on shear stress is investigated over SMCs induced by the interstitial flow both in 2D and three-dimensional (3D) geometries for the media layer. The influence of hypertension (high pressure) on the transport of lowdensity lipoprotein (LDL) through deformable arterial wall layers is also studied. This is due to the pressure-driven convective flow across the arterial wall. The intima and media layers are assumed as homogeneous porous media. The results of the present study reveal that ATP concentration over the surface of SMCs and within the bulk of the media layer is significantly dependent on the distribution of cells. Moreover, the shear stress magnitude and distribution over the SMC surface are affected by transmural pressure and the deformation of the media layer of the aorta wall. This work reflects the fact that the second or even subsequent layers of SMCs may bear shear stresses of the same order of magnitude as the first layer does if cells are arranged in an arbitrary manner. This study has brought new insights into the simulation of the arterial wall, as the previous simplifications have been ignored. The configurations of SMCs used here with elliptic cross sections of SMCs closely resemble the physiological conditions of cells. Moreover, the deformation of SMCs with high transmural pressure which follows the media layer compaction has been studied for the first time. On the other hand, results demonstrate that LDL concentration through the intima and media layers changes significantly as wall layers compress with transmural pressure. It was also noticed that the fraction of leaky junctions across the endothelial cells and the area fraction of fenestral pores over the internal elastic lamina affect the LDL distribution dramatically through the thoracic aorta wall. The simulation techniques introduced in this work can also trigger new ideas for simulating porous media involved in any biomedical, biomechanical, chemical, and environmental engineering applications.

Ydinvoimalaitoksen höyryturbiinin suorituskyvyn laskenta

Diplomityön tavoitteena on selvittää Loviisan ydinvoimalaitoksen höyryturbiinin hyötysuhteen parantamismahdollisuuksia. Työn kuvaan liittyvät oleellisesti höyryturbiinin siipivyöhykkeiden nopeuskolmioiden sekä hyötysuhteiden laskenta. Höyryturbiinien kehityskaarta sekä turbiinin häviökerrointen laskentayhtälöitä on esitetty useasta eri lähteestä ja vuosikymmeniltä. Työssä selvitettiin uusimpia ydinvoimalaitosten kostea höyryturbiinien suunnitteluperusteita lukuisista eri lähteistä. Kaikkien lähteiden mukaan kostean höyryn alueella tapahtuvaa paisuntaa on haasteellista mallintaa. Työssä on esitelty artikkeleissa tulleita eri näkökulmia höyryturbiinien suorituskyvyn parantamiseksi, sekä rakenteellisia että laskennallisia. Työssä esitellään monia turbiinin virtauksen ja suorituskyvyn laskentamenetelmiä. Esimerkiksi Baumannin säännön laskenta on yksinkertainen tapa käsitellä turbiinin suorituskykyä kostean höyryn alueella. Keskeisimpiä tehtyjä havaintoja oli se, että korkeapaineturbiinin ensimmäisestä vaiheesta löytyi mahdollista parannuspotentiaalia Loviisaan ydinvoimalaitoksen tehon lisäämiseksi. Ensimmäisessä vaiheessa on oletettu siipien olevan Laval –tyyppisiä, mutta käytännössä näin ei ole. Korkeapaineturbiinin nykyisen turbosuuttimen toimintaa voitaisiin tehostaa. Lisäksi Loviisan matalapaineturbiinin viimeisen siipivaiheen jälkeen aiheutuu suuret ulosvirtaushäviöt. Osa suurinopeuksisen virtauksen energiasta pystyttäisiin kuitenkin hyödyntämään vielä ulosvirtauskanavassa olevalla diffuusorilla.

Modern recovery boiler design criteria

Engineering and pricing of large recovery boiler were studied in this work. Engineering was carried out with Anita 4.2 which is an engineering program of Andritz. Key initial values were chosen with previous studies. Primary target of this work was to find out the consequences that furnace dimensions and furnace screen vertical part has to boiler pricing. Boilers that were engineered had different rate of furnace width and depth and different heat transfer plate count. Boiler balances were invariable. Boilers with different vertical screen construction were also calculated. First variation was boiler with vertical screen up to furnace roof. Other variation was to connect vertical screen to Pre-boiler generating bank inlet tubes. Total prices were calculated to engineered boilers. Pricing was sort out to heat transfers, high pressure pipes, steel structures, auxiliary equipments and civil/structural costs. This study did not notice parts of the boiler which costs do not vary with the construction of the boiler. Heat transfers had the largest share of costs. Boiler building had the most significant differences between the boilers. Furnace screen had also significant role especially to costs of the boiler building.