Behavioral Responses in Mice Selectively Bred for High and Low Levels of Open-Field Thigmotaxis

In animal psychology, the open-field (OF) test is a traditional method for studying different aspects of rodent behavior, with thigmotaxis (i.e., wallseeking behavior) being one of the best validated OF parameters employed to measure emotionality. The main purpose of the present study was to investigate the selection response in mice selectively bred for high and low levels of OF thigmotaxis (the HOFT and LOFT lines, respectively). The mice (N = 2048) were selected for 23 generations, resulting in bidirectional phenotypic divergence between the two lines; that is, the HOFT mice were more thigmotactic (i.e., more emotional) than the LOFT mice across the different generations. The origin of the line difference in thigmotaxis was further investigated by using the crossfostering paradigm, with the results suggesting that the divergence between the two lines was primarily innate in origin and not influenced by differing maternal behavior. The stability of the selection trait was examined by testing the animals at different ages as well as in varying conditions. The results indicated that the line difference in thigmotaxis was not affected by age at the time of testing, and it also persisted in the different OF testing situations as well as during pregnancy and lactation. The examination of a possible coselection of other characteristics revealed that the more thigmotactic HOFT mice lived longer than the less thigmotactic LOFT mice. In addition, the HOFT mice tended to rear and explore less than the LOFT mice, supporting the general assumption that emotionality and exploration are inversely related. The two lines did not generally differ in ambulation and defecation, that is, in the traditional OF indexes of emotionality, conforming to the suggestion that emotionality is a multidimensional construct. The effects of sex on different OF parameters were also assessed, with the results suggesting that among the HOFT and LOFT lines, the female mice were more emotional than the male mice. The examination of the temporal changes in the HOFT and LOFT lines’ OF behavior revealed some contradictory findings that also partially conflicted with general assumptions. Although this study did not show prominent differences in maternal responsiveness between the HOFT and LOFT mothers, the results suggested that the line divergence in emotionality was more pronounced in the presence of a pup after parturition than during pregnancy. The present study clearly demonstrates that OF thigmotaxis is a strong characteristic for producing two diverging lines of mice. The difference in thigmotaxis between the selectively bred HOFT and LOFT mice seemed to be a stable and robust feature of these animals, and it appeared to stem from a genetic background.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Tilirahan arvostaminen, korkoriskin hallinta ja Suomen talletusmarkkinat

Tilirahalla tarkoitetaan matalan koron tilejä, joihin liittyy tallettajan optio nostaa talletus haluamanaan ajankohtana. Tästä huolimatta tilirahan on havaittu olevan pankille kohtalaisen pysyvää rahoitusta. Pitkä keskimääräinen elinikä yhdistettynä matalaan kustannukseen tekee tilirahasta yhden pankin merkittävimmistä tulonlähteistä. Suuri korkomarginaali ja talletuskoron jäykkyys suhteessa markkinakorkotasoon aiheuttavat puolestaan pankille suuren korkoriskin. Tutkielma vastaa kysymykseen mitä tekijöitä tulee ottaa huomioon tilirahan arvostamisessa ja korkoriskin hallinnassa Suomen talletusmarkkinoilla. Kirjallisuuskatsauksessa esitettyjä tietoja ja niiden soveltuvuutta suomalaisten kotitalouksien tilirahavolyymien kehityksen ennustamisessa arvioidaan lopuksi Suomen Pankista, Eurostatista ja Tilastokeskuksesta saatavien lukujen pohjilta. Virallisista tilastoista johdettujen arvioiden havaittiin osin poikkeavan kirjallisuuskatsauksessa esitetystä. Syynä tähän nähdään eri maiden väliset erot kotitalouksien säästämiskäyttäytymisessä. Suomessa kotitalouksien käyttäytymistä ei näytä ensisijaisesti ohjaavan taloudelliset vaan ei-taloudelliset tekijät kuten parempi likviditeetti. Lisäksi bruttokansantuotteen ja tilirahavolyymin kehityksen välillä havaittiin Suomessa todennäköinen korrelaatio. Alueelliset erot tuleekin huomioida aikaisempia tutkimustuloksia hyödynnettäessä.

Selective leaching of multimetal tailings

Depletion of high grade mineral resources, tightening of environmental regulations and the environmental impact of acid mine drainage caused by sulfidic minerals continuously increase the interest in processing tailings and other mine waste. Treating waste requires additional capital and operational input, but the decrease in size and need of tailings ponds and permits decrease the overall costs. Treatment and utilization of the tailings could also bring added revenue by the recovery of valuables. Leaching of metal sulfides is very demanding and time consuming and hence process conditions need to be carefully optimized. The leaching of sulfides is affected by for example the choice of leaching agent, its concentration and temperature, pH, the redox potential, pressure, pulp density and particle size distribution. With reference to the mine case study the leaching of nickel and copper sulfides, especially the primary minerals pentlandite and chalcopyrite were investigated. Leaching behavior and recoveries for nickel, copper and iron were found out by sulfuric and citric acid leaching experiments using tailings samples of high and low sulfur content. Moderate recoveries were obtained and citric acid seemed more attractive. Increase in temperature and decrease in pulp density had positive effect on the recovery and pH was also proven to have a significant effect on the recovery of valuables. The rate determining step was determined through kinetic modeling in case of all valuables separately. Leaching was controlled by diffusion. The investigated multimetal tailing showed moderate potential in recovering of metal valuables from low grade tailing deposits. The process conditions should however be further optimized.

A Mobile High Sensitivity On-field Organophosphorous Compounds Detecting System for IoT Based Food Safety Tracking

Food safety has always been a social issue that draws great public attention. With the rapid development of wireless communication technologies and intelligent devices, more and more Internet of Things (IoT) systems are applied in the food safety tracking field. However, connection between things and information system is usually established by pre-storing information of things into RFID Tag, which is inapplicable for on-field food safety detection. Therefore, considering pesticide residue is one of the severe threaten to food safety, a new portable, high-sensitivity, low-power, on-field organophosphorus (OP) compounds detection system is proposed in this thesis to realize the on-field food safety detection. The system is designed based on optical detection method by using a customized photo-detection sensor. A Micro Controller Unit (MCU) and a Bluetooth Low Energy (BLE) module are used to quantize and transmit detection result. An Android Application (APP) is also developed for the system to processing and display detection result as well as control the detection process. Besides, a quartzose sample container and black system box are also designed and made for the system demonstration. Several optimizations are made in wireless communication, circuit layout, Android APP and industrial design to realize the mobility, low power and intelligence.

Nestepakkauskartongin ominaisjäykkyyden parantamisen menetelmät

Viime vuosina Tainionkosken KA5:lla valmistettavan nestepakkauskartongin neliömassa, joka jäykkyystavoitteen saavuttamiseksi tarvitaan, on kasvanut. Diplomityön tavoitteena oli selvittää kartongin jäykkyysindeksin heikentymi-seen vaikuttaneet tekijät ja kehittää korjaavia toimenpiteitä. Työn kirjallisuusosassa tutkittiin nestepakkauskartongin laatuominaisuuksia ja jäykkyyden muodostumista. Lisäksi selvitettiin massanvalmistus- ja koneolosuhteiden vaikutusta kartongin jäykkyyteen. Kirjallisuusosassa tutkittiin myös, miten eri massalaadut ja kartongin rakenne vaikuttavat jäykkyyteen. Työn kokeellisessa osassa kartoitettiin jäykkyysindeksin heikkenemisen syitä ja kehitettiin uusia ajomalleja, joilla olisi jäykkyysindeksiin positiivinen vaikutus. Jäykkyysindeksin heikkenemisen syitä selvitettiin massa- ja prosessianalyysien avulla. Lisäksi tutkittiin 3.puristimen muuttamista tasauspuristimeksi ja CTMP:n käyttöä runkokerroksessa sekä korkea- että matalakappaisen valkaisemattoman sellun kanssa. Massa-analyysissä selvisi, että sellun laatu on heikentynyt ja jäykkyysindeksin heikkeneminen johtuu osaltaan siitä. Prosessianalyysissä paljastui useita jäykkyysindeksiä heikentäviä tekijöitä, kuten esimerkiksi kuivatusosan vetoerot, jotka olivat ajautuneet kauas optimitilasta. 3.puristimen muuttaminen tasauspuristimeksi paransi pinnan sileyttä ja kartongin bulkkia, jolloin jäykkyysindeksi kasvoi. CTMP:n käyttö korkeakappaisen sellun kanssa paransi huomattavasti kartongin bulkkia, mutta heikensi palstautumislujuutta ja lisäsi reunaimeytymää. Matalakappaisen sellun ja CTMP:n yhdistelmällä saatiin aikaan hyvä bulkki ja palstautumis-lujuus niin, että reunaimeytymä ei kasvanut ja tuotantonopeus ei laskenut.

Rehufosfaattitehtaan raaka-ainesyöttöjen säätöpiirien kehitys

Diplomityö tehtiin Kemira Chemicals Oy:n Kokkolan tehtaiden rehufosfaattitehtaalla. Työn tavoitteena oli uusien reseptiohjauksien suunnittelu ja käyttöönotto sekä tasaussäiliön pinnansäädön ja rakeistusrummun suhdesäädön suunnittelu. Käyttöhenkilöstön koulutus uuteen prosessinohjaukseen kuului myös osaksi diplomityötä. Uuden reseptiohjauksen avulla pyrittiin saamaan prosessin ohjaus havainnollisemmaksi ja ennustettavammaksi käyttäjille, yhdenmukaistamaan käyttäjien ajotapaa sekä suunnitella tuotereseptit vastaamaan paremmin todellista tuotantoa. Uusi reseptiohjaus mahdollistaa myös lajikekohtaisten parametrien käytön ja hyväksi havaittujen ajoreseptien tallennuksen. Tasaussäiliön pinnankorkeuden säädön tavoitteena on poistaa tuotantokatkokset, jotka johtuivat säiliön tyhjenemisestä tai täyttymisestä. Rakeistusrummun suhdesäädön tavoitteena on reaktoriliemen ja kuiva-ainesyöttöjen oikean suhteen säilyttäminen. Uuden reseptiohjauksen käyttöönoton jälkeen ajoreseptit ovat vastanneet todellista tuotantoa ja tuotantovauhti on jäänyt pysyvästi korkeammalle tasolle. Tasaussäiliön pinnansäätö toimii suunnitellulla tavalla ja on myös otettu käyttöön. Reaktoriliemen ja kuivasyöttöjen suhdesäätö on testattu käytännössä ja toimii halutulla tavalla. Suhdesäädön paremman toiminnan kannalta epätarkkoja toimilaitteita tulisi kuitenkin uusia.

Quantitative market and sales forecast accuracy analysis

The main objective of this master’s thesis was to quantitatively study the reliability of market and sales forecasts of a certain company by measuring bias, precision and accuracy of these forecasts by comparing forecasts against actual values. Secondly, the differences of bias, precision and accuracy between markets were explained by various macroeconomic variables and market characteristics. Accuracy and precision of the forecasts seems to vary significantly depending on the market that is being forecasted, the variable that is being forecasted, the estimation period, the length of the estimated period, the forecast horizon and the granularity of the data. High inflation, low income level and high year-on-year market volatility seems to be related with higher annual market forecast uncertainty and high year-on-year sales volatility with higher sales forecast uncertainty. When quarterly market size is forecasted, correlation between macroeconomic variables and forecast errors reduces. Uncertainty of the sales forecasts cannot be explained with macroeconomic variables. Longer forecasts are more uncertain, shorter estimated period leads to higher uncertainty, and usually more recent market forecasts are less uncertain. Sales forecasts seem to be more uncertain than market forecasts, because they incorporate both market size and market share risks. When lead time is more than one year, forecast risk seems to grow as a function of root forecast horizon. When lead time is less than year, sequential error terms are typically correlated, and therefore forecast errors are trending or mean-reverting. The bias of forecasts seems to change in cycles, and therefore the future forecasts cannot be systematically adjusted with it. The MASE cannot be used to measure whether the forecast can anticipate year-on-year volatility. Instead, we constructed a new relative accuracy measure to cope with this particular situation.

The Detector Control Systems for the CMS Resistive Plate Chamber at LHC

The RPC Detector Control System (RCS) is the main subject of this PhD work. The project, involving the Lappeenranta University of Technology, the Warsaw University and INFN of Naples, is aimed to integrate the different subsystems for the RPC detector and its trigger chain in order to develop a common framework to control and monitoring the different parts. In this project, I have been strongly involved during the last three years on the hardware and software development, construction and commissioning as main responsible and coordinator. The CMS Resistive Plate Chambers (RPC) system consists of 912 double-gap chambers at its start-up in middle of 2008. A continuous control and monitoring of the detector, the trigger and all the ancillary sub-systems (high voltages, low voltages, environmental, gas, and cooling), is required to achieve the operational stability and reliability of a so large and complex detector and trigger system. Role of the RPC Detector Control System is to monitor the detector conditions and performance, control and monitor all subsystems related to RPC and their electronics and store all the information in a dedicated database, called Condition DB. Therefore the RPC DCS system has to assure the safe and correct operation of the sub-detectors during all CMS life time (more than 10 year), detect abnormal and harmful situations and take protective and automatic actions to minimize consequential damages. The analysis of the requirements and project challenges, the architecture design and its development as well as the calibration and commissioning phases represent themain tasks of the work developed for this PhD thesis. Different technologies, middleware and solutions has been studied and adopted in the design and development of the different components and a big challenging consisted in the integration of these different parts each other and in the general CMS control system and data acquisition framework. Therefore, the RCS installation and commissioning phase as well as its performance and the first results, obtained during the last three years CMS cosmic runs, will be

Synthesis of percarboxylic acids in microreactor

Percarboxylic acids are commonly used as disinfection and bleaching agents in textile, paper, and fine chemical industries. All of these applications are based on the oxidative potential of these compounds. In spite of high interest in these chemicals, they are unstable and explosive chemicals, which increase the risk of synthesis processes and transportation. Therefore, the safety criteria in the production process should be considered. Microreactors represent a technology that efficiently utilizes safety advantages resulting from small scale. Therefore, microreactor technology was used in the synthesis of peracetic acid and performic acid. These percarboxylic acids were produced at different temperatures, residence times and catalyst i.e. sulfuric acid concentrations. Both synthesis reactions seemed to be rather fast because with performic acid equilibrium was reached in 4 min at 313 K and with peracetic acid in 10 min at 343 K. In addition, the experimental results were used to study the kinetics of the formation of performic acid and peracetic acid. The advantages of the microreactors in this study were the efficient temperature control even in very exothermic reaction and good mixing due to the short diffusion distances. Therefore, reaction rates were determined with high accuracy. Three different models were considered in order to estimate the kinetic parameters such as reaction rate constants and activation energies. From these three models, the laminar flow model with radial velocity distribution gave most precise parameters. However, sulfuric acid creates many drawbacks in this synthesis process. Therefore, a ´´greener´´ way to use heterogeneous catalyst in the synthesis of performic acid in microreactor was studied. The cation exchange resin, Dowex 50 Wx8, presented very high activity and a long life time in this reaction. In the presence of this catalyst, the equilibrium was reached in 120 second at 313 K which indicates a rather fast reaction. In addition, the safety advantages of microreactors were investigated in this study. Four different conventional methods were used. Production of peracetic acid was used as a test case, and the safety of one conventional batch process was compared with an on-site continuous microprocess. It was found that the conventional methods for the analysis of process safety might not be reliable and adequate for radically novel technology, such as microreactors. This is understandable because the conventional methods are partly based on experience, which is very limited in connection with totally novel technology. Therefore, one checklist-based method was developed to study the safety of intensified and novel processes at the early stage of process development. The checklist was formulated using the concept of layers of protection for a chemical process. The traditional and three intensified processes of hydrogen peroxide synthesis were selected as test cases. With these real cases, it was shown that several positive and negative effects on safety can be detected in process intensification. The general claim that safety is always improved by process intensification was questioned.

Lujien hitsattavien terästen käyttäytyminen -60 °C:ssa

Opinnäytetyö on osa Arctic Materials Technologies Development -projektia, jonka tavoitteena on kehittää perusteita arktisten alueiden sovelluksiin suunnittelun ja valmistuksen kannalta. Arktisella alueella sijaitsee useita potentiaalisia öljy- ja maakaasuesiintymiä, joiden hyödyn-täminen tulee vuosi vuodelta kannattavammaksi ilmaston lämpenemisestä johtuvan merijään heikkenemisen vuoksi. Alin suunnittelulämpötila arktisilla alueilla on -60 °C, mikä aiheuttaa haasteita sekä materiaalinvalinnalle että hitsaukselle. Ferriittisillä teräksillä esiintyy lämpötilasta riippuvaa sitkeyden vaihtelua, jota kutsutaan transi-tiokäyttäytymiseksi. Lämpötilan laskiessa teräksen iskusitkeys sekä murtumissitkeys laske-vat. Arktisissa sovelluskohteissa käytetään yleisesti niukkaseosteisia, mikroseostettuja hie-noraeteräksiä, joille on ominaista erinomaiset sitkeys-, lujuus- sekä hitsattavuusominaisuudet vaativissakin olosuhteissa. Lujat termomekaanisesti valssatut ja nuorrutetut hienoraeteräkset kattavat myötölujuusluokat 355…700 MPa. Tutkimuksissa on saatu vaihtelevia tuloksia ma-teriaalien isku- ja murtumissitkeydestä -60 °C:ssa. Erityisesti sitkeysominaisuudet hitsiaineen ja muutosvyöhykkeen alueiden välillä ovat vaihtelevia. Pienemmällä lämmöntuonnilla ja seostetuilla lisäaineilla saavutetaan kuitenkin pääsääntöisesti parempia sitkeysarvoja. Asiku-laarinen ferriitti sekä alabainiitti ovat toivottavia mikrorakenteita liitoksessa, niiden pienen raekoon johdosta.

Optimization of parameters for fiber laser-MAG hybrid welding in shipbuilding applications

The Arctic region becoming very active area of the industrial developments since it may contain approximately 15-25% of the hydrocarbon and other valuable natural resources which are in great demand nowadays. Harsh operation conditions make the Arctic region difficult to access due to low temperatures which can drop below -50 °C in winter and various additional loads. As a result, newer and modified metallic materials are implemented which can cause certain problems in welding them properly. Steel is still the most widely used material in the Arctic regions due to high mechanical properties, cheapness and manufacturability. Moreover, with recent steel manufacturing development it is possible to make up to 1100 MPa yield strength microalloyed high strength steel which can be operated at temperatures -60 °C possessing reasonable weldability, ductility and suitable impact toughness which is the most crucial property for the Arctic usability. For many years, the arc welding was the most dominant joining method of the metallic materials. Recently, other joining methods are successfully implemented into welding manufacturing due to growing industrial demands and one of them is the laser-arc hybrid welding. The laser-arc hybrid welding successfully combines the advantages and eliminates the disadvantages of the both joining methods therefore produce less distortions, reduce the need of edge preparation, generates narrower heat-affected zone, and increase welding speed or productivity significantly. Moreover, due to easy implementation of the filler wire, accordingly the mechanical properties of the joints can be manipulated in order to produce suitable quality. Moreover, with laser-arc hybrid welding it is possible to achieve matching weld metal compared to the base material even with the low alloying welding wires without excessive softening of the HAZ in the high strength steels. As a result, the laser-arc welding methods can be the most desired and dominating welding technology nowadays, and which is already operating in automotive and shipbuilding industries with a great success. However, in the future it can be extended to offshore, pipe-laying, and heavy equipment industries for arctic environment. CO2 and Nd:YAG laser sources in combination with gas metal arc source have been used widely in the past two decades. Recently, the fiber laser sources offered high power outputs with excellent beam quality, very high electrical efficiency, low maintenance expenses, and higher mobility due to fiber optics. As a result, fiber laser-arc hybrid process offers even more extended advantages and applications. However, the information about fiber or disk laser-arc hybrid welding is very limited. The objectives of the Master’s thesis are concentrated on the study of fiber laser-MAG hybrid welding parameters in order to understand resulting mechanical properties and quality of the welds. In this work only ferrous materials are reviewed. The qualitative methodological approach has been used to achieve the objectives. This study demonstrates that laser-arc hybrid welding is suitable for welding of many types, thicknesses and strength of steels with acceptable mechanical properties along very high productivity. New developments of the fiber laser-arc hybrid process offers extended capabilities over CO2 laser combined with the arc. This work can be used as guideline in hybrid welding technology with comprehensive study the effect of welding parameter on joint quality.

Interpreting marine benthic ecosystem functioning in coastal waters: validating the biological trait concept

Coastal areas harbour high biodiversity, but are simultaneously affected by rapid degradations of species and habitats due to human interactions. Such alterations also affect the functioning of the ecosystem, which is primarily governed by the characteristics or traits expressed by the organisms present. Marine benthic fauna is nvolved in numerous functions such as organic matter transformation and transport, secondary production, oxygen transport as well as nutrient cycling. Approaches utilising the variety of faunal traits to assess benthic community functioning have rapidly increased and shown the need for further development of the concept. In this thesis, I applied biological trait analysis that allows for assessments of a multitude of categorical traits and thus evaluation of multiple functional aspects simultaneously. I determined the functional trait structure, diversity and variability of coastal zoobenthic communities in the Baltic Sea. The measures were related to recruitment processes, habitat heterogeneity, large-scale environmental and taxonomic gradients as well as anthropogenic impacts. The studies comprised spatial scales from metres to thousands of kilometres, and temporal scales spanning one season as well as a decade. The benthic functional structure was found to vary within and between seagrass landscape microhabitats and four different habitats within a coastal bay, in papers I and II respectively. Expressions of trait categories varied within habitats, while the density of individuals was found to drive the functional differences between habitats. The findings in paper III unveiled high trait richness of Finnish coastal benthos (25 traits and 102 cateogries) although this differed between areas high and low in salinity and human pressure. In paper IV, the natural reduction in taxonomic richness across the Baltic Sea led to an overall reduction in function. However, functional richness in terms of number of trait categories remained comparatively high at low taxon richness. Changes in number of taxa within trait categories were also subtle and some individual categories were maintained or even increased. The temporal analysis in papers I and III highlighted generalities in trait expressions and dominant trait categories in a seagrass landscape as well as a “type organism” for the northern Baltic Sea. Some initial findings were made in all four papers on the role of common and rare species and traits for benthic community functioning. The findings show that common and rare species may not always express the same trait categories in relation to each other. Rare species in general did not express unique functional properties. In order to advance the understanding of the approach, I also assessed some issues concerning the limitations of the concept. This was conducted by evaluating the link between trait category and taxonomic richness using especially univariate measures. My results also show the need to collaborate nationally and internationally on safeguarding the utility of taxonomic and trait data. The findings also highlight the importance of including functional trait information into current efforts in marine spatial planning and biomonitoring.

Wind Turbine Direct-Drive Permanent-Magnet Generator with Direct Liquid Cooling for Mass Reduction

Today’s electrical machine technology allows increasing the wind turbine output power by an order of magnitude from the technology that existed only ten years ago. However, it is sometimes argued that high-power direct-drive wind turbine generators will prove to be of limited practical importance because of their relatively large size and weight. The limited space for the generator in a wind turbine application together with the growing use of wind energy pose a challenge for the design engineers who are trying to increase torque without making the generator larger. When it comes to high torque density, the limiting factor in every electrical machine is heat, and if the electrical machine parts exceed their maximum allowable continuous operating temperature, even for a short time, they can suffer permanent damage. Therefore, highly efficient thermal design or cooling methods is needed. One of the promising solutions to enhance heat transfer performances of high-power, low-speed electrical machines is the direct cooling of the windings. This doctoral dissertation proposes a rotor-surface-magnet synchronous generator with a fractional slot nonoverlapping stator winding made of hollow conductors, through which liquid coolant can be passed directly during the application of current in order to increase the convective heat transfer capabilities and reduce the generator mass. This doctoral dissertation focuses on the electromagnetic design of a liquid-cooled direct-drive permanent-magnet synchronous generator (LC DD-PMSG) for a directdrive wind turbine application. The analytical calculation of the magnetic field distribution is carried out with the ambition of fast and accurate predicting of the main dimensions of the machine and especially the thickness of the permanent magnets; the generator electromagnetic parameters as well as the design optimization. The focus is on the generator design with a fractional slot non-overlapping winding placed into open stator slots. This is an a priori selection to guarantee easy manufacturing of the LC winding. A thermal analysis of the LC DD-PMSG based on a lumped parameter thermal model takes place with the ambition of evaluating the generator thermal performance. The thermal model was adapted to take into account the uneven copper loss distribution resulting from the skin effect as well as the effect of temperature on the copper winding resistance and the thermophysical properties of the coolant. The developed lumpedparameter thermal model and the analytical calculation of the magnetic field distribution can both be integrated with the presented algorithm to optimize an LC DD-PMSG design. Based on an instrumented small prototype with liquid-cooled tooth-coils, the following targets have been achieved: experimental determination of the performance of the direct liquid cooling of the stator winding and validating the temperatures predicted by an analytical thermal model; proving the feasibility of manufacturing the liquid-cooled tooth-coil winding; moreover, demonstration of the objectives of the project to potential customers.