Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Suurnopeushilaohjain IGB-transistoreille

Hilalta ohjattavien tehokytkimien, kuten IGBT tai MOSFET, ohjaaminen toteutetaan ohjausjännitettä muuttamalla. Hilaohjaimen tehtävä on ladata tehokytkimen hilakapasitanssia ohjattuun jännitteeseen. Hilaohjaimen siirtämän varauksen suuruuteen vaikuttaa hilakapasitanssin todellinen suuruus ja käytettävä ohjausjännite. Hilaohjaimen virrankäsittelykyky määrittää hilaohjaimen nopeuden siinä mielessä, että ohjattavan komponentin hilavaraus tulisi pystyä lataamaan ja purkamaan tietyssä suhteessa kytkentätaajuuteen. Kytkentätaajuuksien kasvaessa myös hilaohjaimen virrankäsittelykyky sekä hilaohjaimen teho joutuvat uudelleen arvioitaviksi. Työssä perehdytään IGBT:n toimintaan ja hilaohjainratkaisuihin suurilla kytkentätaajuuksilla. Työssä ontutkittu mahdollisuutta rakentaa IGBT:n hilaohjain jo markkinoilla olevista MOSFET:ien hilaohjaimista. Suurnopeushilaohjaimesta suunnitellaanja rakennetaan prototyyppi. Prototyypin suoriutumista tehtävistään tarkastellaan tekemällä mittauksia. Lopuksi arvioidaan asioita joiden tulee muuttua matkalla kohti megahertsien kytkentätaajuuksia.

Vaihtokenttämagnetometrin suunnittelu ja rakentaminen

Tämän työn tavoitteena oli suunnitella ja rakentaa vaihtokenttämagnetometri, jolla voidaan tutkia näytteen magneettisia ominaisuuksia eri lämpötiloissa ja eri taajuuksilla. Menetelmänä käytettiin keskinäisinduktiotekniikkaa, joka on hyvin yleinen tapa tutkia aineen magneettista suskeptibiliteettiä. Magnetometriä ohjataan LabVIEW:lla tehdyllä käyttöliittymällä, joka suunniteltiin yksinkertaiseksi ja helpoksi käyttää. Ohjelma sisältää ohjeet, jotka auttavat parametrien ja toimintojen valinnoissa. LabVIEW:lla ohjataan askelmoottoria, näytteen lämmitintä, lämpötilan mittausta ja lukitusvahvistinta, jolta mittaustulokset saadaan. Laitteen testauksessa käytettiin korkean lämpötilan suprajohdetta YBa2Cu3O6+x, koska sillä saadaan aikaan suurisignaali. Mittaukset tehtiin nestemäisen typen lämpötilassa kahdella eri taajuuden arvolla. Laite antoi oikeanlaisen signaalin ulos eli todettiin laitteen toimivan. Laite toimii hyvin korkeammilla taajuuksilla. Mentäessä hyvin matalille taajuuksille, lukitusvahvistin ei pystynyt lukittumaan, eikä siis siten antanut oikeanlaisia tuloksia.

Hybrid LC Filter for Power Electronic Drives: Theory and Implementation

Power electronic converter drives use, for the sake of high efficiency, pulse-width modulation that results in sequences of high-voltage high-frequency steep-edged pulses. Such a signal contains a set of high harmonics not required for control purposes. Harmonics cause reflections in the cable between the motor and the inverter leading to faster winding insulation ageing. Bearing failures and problems with electromagnetic compatibility may also result. Electrical du/dt filters provide an effective solution to problems caused by pulse-width modulation, thereby increasing the performance and service life of the electrical machines. It is shown that RLC filters effectively decrease the reflection phenomena in the cable. Improved (simple, but effective) solutions are found for both differential- and common-mode signals; these solutions use a galvanic connection between the RLC filter star point and the converter DC link. Foil chokes and film capacitors are among the most widely used components in high-power applications. In actual applications they can be placed in different parts of the cabinet. This fact complicates the arrangement of the cabinet and decreases the reliability of the system. In addition, the inductances of connection wires may prevent filtration at high frequencies. This thesis introduces a new hybrid LC filter that uses a natural capacitance between the turns of the foil choke based on integration of an auxiliary layer into it. The main idea of the hybrid LC filter results from the fact that both the foil choke and the film capacitors have the same roll structure. Moreover, the capacitance between the turns (“intra capacitance”) of the foil inductors is the reason for the deterioration of their properties at high frequencies. It is shown that the proposed filter has a natural cancellation of the intra capacitance. A hybrid LC filter may contain two or more foil layers isolated from each other and coiled on a core. The core material can be iron or even air as in the filter considered in this work. One of the foils, called the main foil, can be placed between the inverter and the motor cable. Other ones, called auxiliary foils, may be connected in star to create differential-mode noise paths, and then coupled to the DC link midpoint to guarantee a traveling path, especially for the common-mode currents. This way, there is a remarkable capacitance between the main foil and the auxiliary foil. Investigations showed that such a system can be described by a simple equivalent LC filter in a wide range of frequencies. Because of its simple hybrid construction, the proposed LC filter can be a cost-effective and competitive solution for modern power drives. In the thesis, the application field of the proposed filter is considered and determined. The basics of hybrid LC filter design are developed further. High-frequency behaviour of the proposed filter is analysed by simulations. Finally, the thesis presents experimental data proving that the hybrid LC filter can be used for du/dt of PWM pulses and reduction of common-mode currents.

Tunable lumped-element bandpass filters for Cognitive Radio application

In this thesis the design of bandpass filters tunable at 400 MHz – 800 MHz was under research. Microwave filters are vital components which provide frequency selectivity in wide variety of electronic systems operating at high frequencies. Due to the occurrence of multi-frequency bands communication and diverse applications of wireless devices, requirement of tunable filters exists. The one of potential implementation of frequency-agile filters is frontends and spectrum sensors in Cognitive Radio (CR). The principle of CR is to detect and operate at a particular available spectrum without interfering with the primary user’s signals. This new method allows improving the efficiency of utilizing allocated spectrum such as TV band (400 MHz – 800 MHz). The focus of this work is development of sufficiently compact, low cost tunable filters with quite narrow bandwidth using currently available lumped-element components and PCB board technology. Filter design, different topologies and methods of tuning of bandpass filters are considered in this work. As a result, three types of topologies of bandpass filter were simulated and realised. They use digitally tunable capacitors (DTCs) for adjusting central frequency at TV "white space" spectrum. Measurements revealed that schematics presented in this work have proper output response and filters are successfully tuned by DTCs.