Calibration of time domain reflectometry (DTR) for soil moisture measurements in cultivated peat soils

Tiivistelmä: TDR-mittausten kalibrointi viljeltyjen turvemaiden kosteuden mittaamiseen

Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Frequency-Domain and Wide-Pulse Time-Domain Measurements of Lanthanide Luminescence and Lanthanide-Based Resonance Energy Transfer

Resonance energy transfer (RET) is a non-radiative transfer of the excitation energy from the initially excited luminescent donor to an acceptor. The requirements for the resonance energy transfer are: i) the spectral overlap between the donor emission spectrum and the acceptor absorption spectrum, ii) the close proximity of the donor and the acceptor, and iii) the suitable relative orientations of the donor emission and the acceptor absorption transition dipoles. As a result of the RET process the donor luminescence intensity and the donor lifetime are decreased. If the acceptor is luminescent, a sensitized acceptor emission appears. The rate of RET depends strongly on the donor–acceptor distance (r) and is inversely proportional to r6. The distance dependence of RET is utilized in binding assays. The proximity requirement and the selective detection of the RET-modified emission signal allow homogeneous separation free assays. The term lanthanide-based RET is used when luminescent lanthanide compounds are used as donors. The long luminescence lifetimes, the large Stokes’ shifts and the intense, sharply-spiked emission spectra of the lanthanide donors offer advantages over the conventional organic donor molecules. Both the organic lanthanide chelates and the inorganic up-converting phosphor (UCP) particles have been used as donor labels in the RET based binding assays. In the present work lanthanide luminescence and lanthanide-based resonance energy transfer phenomena were studied. Luminescence lifetime measurements had an essential role in the research. Modular frequency-domain and time-domain luminometers were assembled and used successfully in the lifetime measurements. The frequency-domain luminometer operated in the low frequency domain ( 100 kHz) and utilized a novel dual-phase lock-in detection of the luminescence. One of the studied phenomena was the recently discovered non-overlapping fluorescence resonance energy transfer (nFRET). The studied properties were the distance and temperature dependences of nFRET. The distance dependence was found to deviate from the Förster theory and a clear temperature dependence was observed whereas conventional RET was completely independent of the temperature. Based on the experimental results two thermally activated mechanisms were proposed for the nFRET process. The work with the UCP particles involved the measurement of the luminescence properties of the UCP particles synthesized in our laboratory. The goal of the UCP particle research is to develop UCP donor labels for binding assays. In the present work the effect of the dopant concentrations and the core–shell structure on the total up-conversion luminescence intensity, the red–green emission ratio, and the luminescence lifetime was studied. Also the non-radiative nature of the energy transfer from the UCP particle donors to organic acceptors was demonstrated for the first time in aqueous environment and with a controlled donor–acceptor distance.

Online Ultrasound Measurements of Membrane Compaction

There are several filtration applications in the pulp and paper industry where the capacity and cost-effectiveness of processes are of importance. Ultrafiltration is used to clean process water. Ultrafiltration is a membrane process that separates a certain component or compound from a liquid stream. The pressure difference across the membrane sieves macromolecules smaller than 0.001-0.02 μm through the membrane. When optimizing the filtration process capacity, online information about the conditions of the membrane is needed. Fouling and compaction of the membrane both affect the capacity of the filtration process. In fouling a “cake” layer starts to build on the surface of the membrane. This layer blocks the molecules from sieving through the membrane thereby decreasing the yield of the process. In compaction of the membrane the structure is flattened out because of the high pressure applied. The higher pressure increases the capacity but may damage the structure of the membrane permanently. Information about the compaction is needed to effectively operate the filters. The objective of this study was to develop an accurate system for online monitoring of the condition of the membrane using ultrasound reflectometry. Measurements of ultrafiltration membrane compaction were made successfully utilizing ultrasound. The results were confirmed by permeate flux decline, measurements of compaction with a micrometer, mechanical compaction using a hydraulic piston and a scanning electron microscope (SEM). The scientific contribution of this thesis is to introduce a secondary ultrasound transducer to determine the speed of sound in the fluid used. The speed of sound is highly dependent on the temperature and pressure used in the filters. When the exact speed of sound is obtained by the reference transducer, the effect of temperature and pressure is eliminated. This speed is then used to calculate the distances with a higher accuracy. As the accuracy or the resolution of the ultrasound measurement is increased, the method can be applied to a higher amount of applications especially for processes where fouling layers are thinner because of smaller macromolecules. With the help of the transducer, membrane compaction of 13 μm was measured in the pressure of 5 bars. The results were verified with the permeate flux decline, which indicated that compaction had taken place. The measurements of compaction with a micrometer showed compaction of 23–26 μm. The results are in the same range and confirm the compaction. Mechanical compaction measurements were made using a hydraulic piston, and the result was the same 13 μm as obtained by applying the ultrasound time domain reflectometry (UTDR). A scanning electron microscope (SEM) was used to study the structure of the samples before and after the compaction.

Dynamic Model of a Small Once-Through Boiler

In this study, a model for the unsteady dynamic behaviour of a once-through counter flow boiler that uses an organic working fluid is presented. The boiler is a compact waste-heat boiler without a furnace and it has a preheater, a vaporiser and a superheater. The relative lengths of the boiler parts vary with the operating conditions since they are all parts of a single tube. The present research is a part of a study on the unsteady dynamics of an organic Rankine cycle power plant and it will be a part of a dynamic process model. The boiler model is presented using a selected example case that uses toluene as the process fluid and flue gas from natural gas combustion as the heat source. The dynamic behaviour of the boiler means transition from the steady initial state towards another steady state that corresponds to the changed process conditions. The solution method chosen was to find such a pressure of the process fluid that the mass of the process fluid in the boiler equals the mass calculated using the mass flows into and out of the boiler during a time step, using the finite difference method. A special method of fast calculation of the thermal properties has been used, because most of the calculation time is spent in calculating the fluid properties. The boiler was divided into elements. The values of the thermodynamic properties and mass flows were calculated in the nodes that connect the elements. Dynamic behaviour was limited to the process fluid and tube wall, and the heat source was regarded as to be steady. The elements that connect the preheater to thevaporiser and the vaporiser to the superheater were treated in a special way that takes into account a flexible change from one part to the other. The model consists of the calculation of the steady state initial distribution of the variables in the nodes, and the calculation of these nodal values in a dynamic state. The initial state of the boiler was received from a steady process model that isnot a part of the boiler model. The known boundary values that may vary during the dynamic calculation were the inlet temperature and mass flow rates of both the heat source and the process fluid. A brief examination of the oscillation around a steady state, the so-called Ledinegg instability, was done. This examination showed that the pressure drop in the boiler is a third degree polynomial of the mass flow rate, and the stability criterion is a second degree polynomial of the enthalpy change in the preheater. The numerical examination showed that oscillations did not exist in the example case. The dynamic boiler model was analysed for linear and step changes of the entering fluid temperatures and flow rates.The problem for verifying the correctness of the achieved results was that there was no possibility o compare them with measurements. This is why the only way was to determine whether the obtained results were intuitively reasonable and the results changed logically when the boundary conditions were changed. The numerical stability was checked in a test run in which there was no change in input values. The differences compared with the initial values were so small that the effects of numerical oscillations were negligible. The heat source side tests showed that the model gives results that are logical in the directions of the changes, and the order of magnitude of the timescale of changes is also as expected. The results of the tests on the process fluid side showed that the model gives reasonable results both on the temperature changes that cause small alterations in the process state and on mass flow rate changes causing very great alterations. The test runs showed that the dynamic model has no problems in calculating cases in which temperature of the entering heat source suddenly goes below that of the tube wall or the process fluid.

Kalibrointimenetelmä planaaristen siirtojohtojen mittaamiseen

Tässä diplomityössä tutkittiin TRL-kalibroinnin käyttämistä tasomaisten siirtojohtojen sähköisten parametrien määrittämisessä taajuusalueella 0,3 – 12 GHz. Työssä perehdyttiin TRL-kalibroinnin käyttämiseen piirianalysaattorilla toteutettujen mittauksien mittauskalibrointiin sekä kalibrointiin tarvittavien kalibrointistandardien mitoittamiseen. Kalibrointistandardit suunniteltiin ja toteutettiin sekä mikroliuska- että liuskajohdoille, joiden toiminnallisuutta tarkasteltiin sekä taajuustason että aikatason mittausten avulla. Työssä perehdyttiin myös kalibrointistandardien liityntärajapinnan suunniteluun ja toteuttamiseen. Saatujen tulosten perusteella voitiin osoittaa mikroliuskajohtokitin soveltuvan hyvin mittauskalibroinnin toteuttamiseen tarkoissa mittaussovelluksissa.

Power quality improving with virtual flux-based voltage source line converter

Line converters have become an attractive AC/DC power conversion solution in industrial applications. Line converters are based on controllable semiconductor switches, typically insulated gate bipolar transistors. Compared to the traditional diode bridge-based power converters line converters have many advantageous characteristics, including bidirectional power flow, controllable de-link voltage and power factor and sinusoidal line current. This thesis considers the control of the lineconverter and its application to power quality improving. The line converter control system studied is based on the virtual flux linkage orientation and the direct torque control (DTC) principle. A new DTC-based current control scheme is introduced and analyzed. The overmodulation characteristics of the DTC converter are considered and an analytical equation for the maximum modulation index is derived. The integration of the active filtering features to the line converter isconsidered. Three different active filtering methods are implemented. A frequency-domain method, which is based on selective harmonic sequence elimination, anda time-domain method, which is effective in a wider frequency band, are used inharmonic current compensation. Also, a voltage feedback active filtering method, which mitigates harmonic sequences of the grid voltage, is implemented. The frequency-domain and the voltage feedback active filtering control systems are analyzed and controllers are designed. The designs are verified with practical measurements. The performance and the characteristics of the implemented active filtering methods are compared and the effect of the L- and the LCL-type line filteris discussed. The importance of the correct grid impedance estimate in the voltage feedback active filter control system is discussed and a new measurement-based method to obtain it is proposed. Also, a power conditioning system (PCS) application of the line converter is considered. A new method for correcting the voltage unbalance of the PCS-fed island network is proposed and experimentally validated.

Patents in the Information and Communications Technology Sector - Development Trends, Problem Areas and Pressures for Change

The patent system was created for the purpose of promoting innovation by granting the inventors a legally defined right to exclude others in return for public disclosure. Today, patents are being applied and granted in greater numbers than ever, particularly in new areas such as biotechnology and information andcommunications technology (ICT), in which research and development (R&D) investments are also high. At the same time, the patent system has been heavily criticized. It has been claimed that it discourages rather than encourages the introduction of new products and processes, particularly in areas that develop quickly, lack one-product-one-patent correlation, and in which theemergence of patent thickets is characteristic. A further concern, which is particularly acute in the U.S., is the granting of so-called 'bad patents', i.e. patents that do not factually fulfil the patentability criteria. From the perspective of technology-intensive companies, patents could,irrespective of the above, be described as the most significant intellectual property right (IPR), having the potential of being used to protect products and processes from imitation, to limit competitors' freedom-to-operate, to provide such freedom to the company in question, and to exchange ideas with others. In fact, patents define the boundaries of ownership in relation to certain technologies. They may be sold or licensed on their ownor they may be components of all sorts of technology acquisition and licensing arrangements. Moreover, with the possibility of patenting business-method inventions in the U.S., patents are becoming increasingly important for companies basing their businesses on services. The value of patents is dependent on the value of the invention it claims, and how it is commercialized. Thus, most of them are worth very little, and most inventions are not worth patenting: it may be possible to protect them in other ways, and the costs of protection may exceed the benefits. Moreover, instead of making all inventions proprietary and seeking to appropriate as highreturns on investments as possible through patent enforcement, it is sometimes better to allow some of them to be disseminated freely in order to maximize market penetration. In fact, the ideology of openness is well established in the software sector, which has been the breeding ground for the open-source movement, for instance. Furthermore, industries, such as ICT, that benefit from network effects do not shun the idea of setting open standards or opening up their proprietary interfaces to allow everyone todesign products and services that are interoperable with theirs. The problem is that even though patents do not, strictly speaking, prevent access to protected technologies, they have the potential of doing so, and conflicts of interest are not rare. The primary aim of this dissertation is to increase understanding of the dynamics and controversies of the U.S. and European patent systems, with the focus on the ICT sector. The study consists of three parts. The first part introduces the research topic and the overall results of the dissertation. The second part comprises a publication in which academic, political, legal and business developments that concern software and business-method patents are investigated, and contentiousareas are identified. The third part examines the problems with patents and open standards both of which carry significant economic weight inthe ICT sector. Here, the focus is on so-called submarine patents, i.e. patentsthat remain unnoticed during the standardization process and then emerge after the standard has been set. The factors that contribute to the problems are documented and the practical and juridical options for alleviating them are assessed. In total, the dissertation provides a good overview of the challenges and pressures for change the patent system is facing,and of how these challenges are reflected in standard setting.

Kulmastabiilisuuden mallinnus

Työn tavoitteena oli kartoittaa vaihtoehtoisia menetelmiä perinteiselle aikatasossa tapahtuvalle kulmastabiilisuuden mallinnukselle käyttövarmuustarkastelussa. Vaihtoehtoisiin menetelmiin tutustuttiin kirjallisuuden avulla ja valittiin menetelmä testattavaksi pohjoismaisessa yhteiskäyttöjärjestelmässä. Vaihtoehtoisen menetelmän ominaisuusvaatimuksiin kuului nopeampi laskenta, luotettava stabiilien ja epästabiilien tilanteiden seulontakyky ja menetelmän antama indeksi stabiilisuus-/epästabiilisuusasteesta. Pääasiassa menetelmät, joihin tutustuttiin, arvioivat vain transienttia stabiilisuutta. SIME-menetelmä soveltui myös dynaamisen stabiilisuuden arviointiin. Suomessa voi dynaamisella stabiilisuudella olla tulevaisuudessa merkittävä rooli käyttövarmuustarkasteluissa. SIME-menetelmän toimivuutta testattiin osin yksinkertaistetulla Nordel-verkkomallilla, ja saadut tulokset olivat lupaavia. Menetelmä täytti uudelle menetelmälle asetetut vaatimukset, vaikka ongelmiakin esiintyi. Testauksessa käytetyn menetelmän edelleen kehittäminen ja menetelmän testaaminen täydellisellä verkkomallilla on suositeltavaa.

Paperitehtaan energianhuoltoratkaisut

Työssä tarkastellaan paperitehtaan tarvitsemia energiavirtoja ja niiden tuottamista paperitehtaan yhteydessä olevalla voimalaitoksella. Työn perusteella tehtiin laskentamalli, jolla voidaan vertailla esisuunnittelun alussa eri laitoskonsepteja tarkemman suunnittelun pohjaksi. Tyypillistä paperitehtaan energiantuotannolle on suuri vuosittainen huipunkäyttöaika ja energiantuotannolta vaadittava luotettavuus. Lisäksi energiantuotannon voidaan edellyttää käyttävän hyödyksi paperintuotannon sivuainevirtoja. Tarkastelu on suoritettu kannattavuustarkasteluna ottaen huomiin koko voimalaitoksen käyttöiän kustannukset. Kannattavuuteen vaikuttavat investointikustannusten lisäksi merkittävästi myös polttoainekustannukset. Herkkyystarkastelulla voidaan vertailla eri konseptien kannattavuutta eri lähtötietoarvoilla. Erilaiset maksulliset päästökiintiöt voivat muuttaa eri konseptien keskinäistä kannattavuutta. Päästökiintiöiden markkinat ovat kuitenkin vielä selkiytymättömät.

Hakkuriteholähteen säädön suunnittelu

Diplomityö on tehty osana ETX-tutkimushanketta: 'Volyymiteholähteen suunnittelumetodien kehitys ja optimointi DFM-viitekehyksessä'. Työssä suunnitellaan hakkuriteholähteelle säätäjä. Tähän suunnittelun sektoriin syventyminen on teollisuudessa jäänyt monesti vähälle. Säätö on tavallisesti ajan puutteen ja apuvälineiden käytön osaamattomuuden tai puuttumisen takia suunniteltu kokeilemalla. Työssä muodostetaan jännitemuotoisesti säädetylle hakkurille piensignaalimallilla linearisoidut siirtofunktiot, joiden perusteella voidaan tarkastella hakkurin stabiilisuutta takaisinkytketyssä säätösilmukassa. Stabiiliustarkastelu tehdään taajuustasossa käyttäen Bode-kuvaajia. Näiden kuvaajien perusteella viritetään järjestelmään säätäjä. Säätäjän toimintaa aikatasossa tarkastellaan simuloimalla ja reaalisen laitteen toimimista laboratorioprototyypin avulla. Tulosten perusteella voidaan todeta, että jännitemuotoisella säädöllä flyback-hakkuri saadaan nopeaksi epäjatkuvalla käämivirralla. Mikäli halutaan hakkurin toimivan jatkuvalla käämivirralla, on syytä käyttää muita säätömenetelmiä, esimerkiksi huippuvirtasäätöä.

A Co-Processor Approach for Efficient Java Execution in Embedded Systems

This thesis deals with a hardware accelerated Java virtual machine, named REALJava. The REALJava virtual machine is targeted for resource constrained embedded systems. The goal is to attain increased computational performance with reduced power consumption. While these objectives are often seen as trade-offs, in this context both of them can be attained simultaneously by using dedicated hardware. The target level of the computational performance of the REALJava virtual machine is initially set to be as fast as the currently available full custom ASIC Java processors. As a secondary goal all of the components of the virtual machine are designed so that the resulting system can be scaled to support multiple co-processor cores. The virtual machine is designed using the hardware/software co-design paradigm. The partitioning between the two domains is flexible, allowing customizations to the resulting system, for instance the floating point support can be omitted from the hardware in order to decrease the size of the co-processor core. The communication between the hardware and the software domains is encapsulated into modules. This allows the REALJava virtual machine to be easily integrated into any system, simply by redesigning the communication modules. Besides the virtual machine and the related co-processor architecture, several performance enhancing techniques are presented. These include techniques related to instruction folding, stack handling, method invocation, constant loading and control in time domain. The REALJava virtual machine is prototyped using three different FPGA platforms. The original pipeline structure is modified to suit the FPGA environment. The performance of the resulting Java virtual machine is evaluated against existing Java solutions in the embedded systems field. The results show that the goals are attained, both in terms of computational performance and power consumption. Especially the computational performance is evaluated thoroughly, and the results show that the REALJava is more than twice as fast as the fastest full custom ASIC Java processor. In addition to standard Java virtual machine benchmarks, several new Java applications are designed to both verify the results and broaden the spectrum of the tests.

Neurophysiologic diagnosis, clinical symptoms and neuropathologic findings in polyneuropathies

Tausta: Polyneuropatia (PNP) on ääreishermoston sairaus, joka aiheuttaa laaja-alaisia, yleensä symmetrisiä vaurioita ääreishermostossa. PNP:aan johtavia syitä on satoja. Tavoitteet: Löytää parhaat neurofysiologiset menetelmät uremian, myelooman hoidossa käytettävän talidomidin sekä Fabryn taudin aiheuttaman PNP:n diagnosoimiseksi. Fabryn taudissa tutkin lisäksi ohutsäieneuropatian aiheuttamia neuropatologisia löydöksiä iholta otetusta koepalasta. Tutkimuksissa kartoitettiin lisäksi PNP:n aiheuttamien subjektiivisten oireiden korrelaatio neurofysiologisten ja neuropatologisten löydösten kanssa. Munuaisten vajaatoimintaa sairastavilla potilailla tavoitteena oli tutkia dialyysihoidon tehon vaikutusta autonomisen hermoston toimintaan sekä yhden dialyysikerran vaikutusta neurofysiologisiin löydöksiin. Aineisto ja menetelmät: I: Tutkittiin 21 uremiapotilaan sensoristen ja motoristen hermojen vasteet, värinä- sekä lämpötuntokynnykset ennen ja jälkeen hemodialyysin. Subjektiiviset PNP oireet kartoitettiin PNP oireita kysyvillä kaavakkeella. II:12 talidomidi hoitoa saavaa myeloomapotilasta, tutkimuksen menetelmät olivat samat kuin tutkimuksessa I. III: 12 Fabryn tautia sairastavaa potilasta, edellä mainittujen neurofysiologisten tutkimusten lisäksi potilailta otettiin ihobiopsia säären alueelta. Ihobiopsiasta laskettiin ohuiden hermosyiden määrä koepalan värjäyksen jälkeen. Subjektiiviset PNP oireet kartoitettiin kyselykaavakkeella. Sydämen sykevaihtelu tutkittiin levossa taajuustason analyysillä. IV: 32 uremiapotilaan autonomisen hermoston toimintaa tutkittiin sydämen sykevaihtelun aikatason analysillä, paksujen myelinoituneiden säikeiden toimintaa tutkittiin perifeeristen sensoristen hermojen mittauksilla toistetusti noin 2.9 vuoden aikana. Tulokset: Ureemisen PNP:n diagnostiikassa herkimmät tutkimukset ovat F-aaltojen parametrit alaraajojen motorisista hermoista, värinätuntokynnys alaraajoista sekä suralishermon amplitudi. Positiiviset PNP oireet uremiassa korreloivat värinätunto-kynnyksen sekä sensoristen hermojen neurografialöydösten kanssa. Neurofysiologisten tutkimusten ajankohdalla dialyysiajankohtaan nähden ei ole merkitystä. Talidomidi-PNP on pääasiassa sensorinen, mutta motoriset syyt ovat lievästi vaurioituneet. Talidomidi PNP:ssa subjektiiviset oireet korreloivat huonosti neurofysiologisten löydösten kanssa. Fabryn taudissa naisilla on oletettua enemmän ohutsäieneuropatian aiheuttamia oireita ja löydöksiä. Paksujen säikeiden löydöksiä ei tullut esiin. Ohutsäieneuropatian diagnostiikassa ihobiopsia ja kvantitatiiviset tuntokynnysmittaustestit täydentävät toisiaan. Tehokas dialyysi parantaa autonomisen hermoston toimintaa uremiapotilailla. Päätelmät: Erityyppisten polyneuropatioiden diagnostiikassa pitää etukäteen valita PNP tyypille oikeat tutkimusmenetelmät raskaiden tutkimuspatterien vähentämiseksi sekä diagnostiikan parantamiseksi. PNP:n aiheuttamat oireet ja kliiniset löydökset pitää aina tutkia, mutta yksin ne eivät ole herkkiä PNP:n diagnostiikassa.

Kestomagneettigeneraattorin lämmönsiirron mallinnus tuulivoimakäytössä

Pyörivien sähkökoneiden suunnittelussa terminen suunnittelu on yhtä tärkeää kuin sähköinen ja mekaaninen suunnittelukin. Tässä diplomityössä tarkoituksena on kehittää ilmajäähdytteisten kestomagneettigeneraattorien laskentaan soveltuva lämmönsiirtymismalli, jolla staattorin lämpötilajakauma voitaisiin selvittää. Kehitetty lämmönsiirtymismalli perustuu kolmiulotteiseen äärellisen erotuksen (finite difference) menetelmään. Malli ottaa huomioon lämmönjohtumisen staattorin aktiiviosissa ja konvektion jäähdytysilmavirtaan. Mallissa on myös yksinkertainen painehäviölaskenta jäähdytysjärjestelmän komponenttien mitoittamista varten. Laskentamallilla lasketaan esimerkkitapauksena 4,3 MW:n kestomagneettigeneraattorin jäähdytystä eri toimintapisteissä. Tuloksia verrataan CFD-mallinnuksen antamiin tuloksiin sekä kokeellisten mittausten antamiin tuloksiin.

Supermatrix-hankkeen vahvuudet, heikkoudet, mahdollisuudet ja uhat

Supermatrix on Finnet-liitto ry:n jäsenyritysten hanke, joka tuo nopeiden valokuituyhteyksien avulla erilaisia sähköisiä palveluita kuluttajien koteihin ja yritysten toimipisteisiin. Näitä palveluita ovat mm. virtualisoidut henkilö-kohtaiset tietokoneet, tiedon tallennuspalvelut ja multimediasisältö, kuten teräväpiirtotelevisio. Tässä diplomityössä arvioidaan Supermatrixin palveluiden toteutumis-mahdollisuuksia sekä teknologian, että markkinoiden kannalta. Työn tarkoituksena oli myös laskea virtualisoitujen tietokoneiden avulla tuotetun työpöytäpalvelun tuotantokustannus. Kustannuslaskentaa varten testattiin useiden valmistajien teknologioita, ja parhaimmista vaihtoehdoista laskettiin tuotantokustannukset. Tulevia Supermatrix-operaattoreita varten kehitettiin työkalu, jolla työpöytäpalvelun vaatimien investointien kannattavuus saadaan nopeasti selville. Tuotantohintojen laskelmat osoittavat, että työpöytäpalvelua on taloudelli-sesti mahdollista tuottaa luomaan lisäarvoa nopeille laajakaistayhteyksille. Yrityksissä työpöytien virtualisointi on jo tämän päivän teknologiaa, mutta kuluttaja-asiakkaiden innostuminen palvelusta vaatii uuden markkinan luomisen. Uhkana on, että kuluttajien ostokäyttäytymisen muuttaminen ei onnistu, koska Supermatrix ei tuota fyysisen tuotteen ostamisen tarjoamaa mielihyvää.