Characterisation of Hydrophobic Nonfibrous Material and Its Removal From Pulp Suspension

Paperin ja kartongin kierrätys lisääntyy taloudellisten intressien ja ympäristöhygieenisten tavoitteiden takia jatkuvasti. Lisääntyvän kierrätyksen myötä myös paperin ja kartongin epäpuhtauksien määrä kasvaa, mikä huonontaa kierrätysraaka-aineen laatua. Tämän työn tarkoituksena on antaa perustietoa eräästä kartongin päällystyksessä käytettävästä hydrofobisesta materiaalista, epäpuhtaan kartongin kierrätyksestä sekä ongelmista, joita epäpuhtaan kartongin kierrätyksestä syntyy. Kierrätyskuidun fraktiointi on yksinkertainen prosessi aallotuskartongin, testilainerin ja taivekartongin valmistuksessa. Kierrätysprosessin ensisijaisia tehtäviä ovat kuidutus ja epäpuhtauksien poisto sekä näiden epäpuhtauksien vaikutusten eliminointi, jotta kierrätysmassan laatuvaatimukset täyttyvät. Lisääntynyt epäpuhtauksien määrä raaka-aineessa asettaa vaatimuksia lajitteluprosessin kehittämiseksi. Nykyaikaisilla kierrätyslaitoksilla ei pystytä käsittelemään ylettömiä määriä epäpuhtauksia. Epäpuhtaudet aiheuttavat ongelmia ajettavuuteen ja heikentävät tuotteen laatua kierrätysprosessissa. Epäpuhtauksien poistoon on olemassa useita teknisiä ratkaisuja, mutta minkään niistä ei ole todettu täysin poistavan kaikkia ongelmia. Työn kokeellisessa osassa kartongin päällystykseen käytettävää hydrofobista materiaalia analysoitiin erilaisin menetelmin. Tutkittiin myös erilaisten olosuhteiden vaikutusta tämän materiaalin poistoon.

Determining, Balancing and Controlling of Pitch and White Pitch at Stora Enso Kabel Production Line 4

Työn ensimmäisenä tarkoituksena oli kartoittaa kiinteä-neste ja neste-neste uuttomenetelmillä pihkan ja valkopihkan määrä Stora Enso Kabelin tuotantolinja 4:llä. Työn kannalta oli myöstärkeää saada selvyys saostumien koostumuksesta. Lopullinen päämäärä oli automatisoida fiksatiivin annostelu uuden, jatkuvatoimisen märänpäänanalysaattorin avulla. Mäntyosuuden kasvattaminen hiokemassassa lisää hydrofobisten partikkeleiden lukumäärää, minkä uskotaan lisäävän saostumariskiä. Työtä varten kehitetty neste-neste uuttomenetelmä, jota ei ole liiemmin paperiteollisuudessa käytetty, voi olla hyvä menetelmä lipofiilisten komponenttien määrän arviointiin tietyssä määrässä massa- tai prosessivesinäytettä. Virtaussytometri-menetelmän avulla tutkittiin pihka- tai valkopihkapartikkeleiden määrää ja kokojakaumaa eri prosessinäytteissä. Virtaussytometri-menetelmällä mitattujen valkopihkapartikkeleiden lukumäärän ja päällystetyn hylyn saostimen suodoksen sameuden välille löytyiselvä korrelaatio. Fiksatiivimäärän vaikutusta päällystetyn hylyn saostimen suodoksen sameuteen tutkittiin koeajojaksolla, jossa fiksatiivin annostelua säädettiin käsin. Käytetyt annosmäärät eivät riittäneet sameuden pitämiseen tasaisena matalalla tasolla.

Choice of Optimal MembraneProcesses for Economical Treatment of Paper Machine Clear Filtrate

In this thesis membrane filtration of paper machnie clear filtrate was studied. The aim of the study was to find membrane processes which are able to produce economically water of sufficient purity from paper machine white water or its saveall clarified fractions for reuse in the paper machnie short circulation. Factors affecting membrane fouling in this application were also studied. The thesis gives an overview af experiments done on a laboratory and a pilot scale with several different membranes and membrane modules. The results were judged by the obtained flux, the fouling tendency and the permeate quality assessed with various chemical analyses. It was shown that membrane modules which used a turbulence promotor of some kind gave the highest fluexes. However, the results showed that the greater the reduction in the concentration polarisation layer caused by increased turbulence in the module, the smaller the reductions in measured substances. Out of the micro-, ultra- and nanofiltration membranes tested, only nanofiltration memebranes produced permeate whose quality was very close to that of the chemically treated raw water used as fresh water in most paper mills today and which should thus be well suited for reuse as shower water both in the wire and press section. It was also shown that a one stage nanofiltration process was more effective than processes in which micro- or ultrafiltration was used as pretreatment for nanofiltration. It was generally observed that acidic pH, high organic matter content, the presence of multivalent ions, hydrophobic membrane material and high membrane cutoff increased the fouling tendency of the membranes.

The use of branched ketenedimers in solving the deposit problems related to the internal sizing of uncoated fine paper

Alkyl ketene dimers (AKD) are effective and highly hydrophobic sizing agents for the internal sizing of alkaline papers, but in some cases they may form deposits on paper machines and copiers. In addition, alkenyl succinic anhydrides (ASA)- based sizing agents are highly reactive, producing on-machine sizing, but under uncontrolled wet end conditions the hydrolysis of ASA may cause problems. This thesis aims at developing an improved ketene dimer based sizing agent that would have a lower deposit formation tendency on paper machines and copiers than a traditional type of AKD. The aim is also to improve the ink jet printability of a AKD sized paper. The sizing characteristics ofketene dimers have been compared to those of ASA. A lower tendency of ketene dimer deposit formation was shown in paper machine trials and in printability tests when branched fatty acids were used in the manufacture of a ketene dimer basedsizing agent. Fitting the melting and solidification temperature of a ketene dimer size to the process temperature of a paper machine or a copier contributes to machine cleanliness. A lower hydrophobicity of the paper sized with branched ketene dimer compared to the paper sized with traditional AKD was discovered. However, the ink jet print quality could be improved by the use of a branched ketene dimer. The branched ketene dimer helps in balancing the paper hydrophobicity for both black and color printing. The use of a high amount of protective colloidin the emulsification was considered to be useful for the sizing performance ofthe liquid type of sizing agents. Similar findings were indicated for both the branched ketene dimer and ASA.

Spray coating technique asa surface treatment for woodcontaining paper grades

The objective of this work was to introduce the emerging non-contacting spray coating process and compare it to the existing coating techniques. Particular emphasis was given to the details of the spraying process of paper coating colour and the base paper requirements set by the new coating method. Spraying technology itself is nothing new, but the atomisation process of paper coating colour is quite unknown to the paper industry. The differences between the rheology of painting and coating colours make it very difficult to utilise the existing information from spray painting research. Based on the trials, some basic conclusion can be made:The results of this study suggest that the Brookfield viscosity of spray coating colour should be as low as possible, presently a 50 mPas level is regarded as an optimum. For the paper quality and coater runnability, the solids level should be as high as possible. However, the graininess of coated paper surface and the nozzle wear limits the maximum solids level to 60 % at the moment. Most likelydue to the low solids and low viscosity of the coating colour the low shear Brookfield viscosity correlates very well with the paper and spray fan qualities. High shear viscosity is also important, but yet less significant than the low shear viscosity. Droplet size should be minimized and besides keeping the brrokfield viscosity low that can be helped by using a surfactant or dispersing agent in the coating colour formula. Increasing the spraying pressure in the nozzle can also reduce the droplet size. The small droplet size also improves the coating coverage, since there is hardly any levelling taking place after the impact with the base paper. Because of the lack of shear forces after the application, the pigment particles do not orientate along the paper surface. Therefore the study indicates that based on the present know-how, no quality improvements can be obtained by the use of platy type of pigments. The other disadvantage of them is the rapid deterioration of the nozzle lifetime. Further research in both coating colour rheology and nozzle design may change this in the future, but so far only round shape pigments, like typically calcium carbonate is, can be used with spray coating. The low water retention characteristics of spray coating, enhanced by the low solids and low viscosity, challenge the base paper absorption properties.Filler level has to be low not to increase the number of small pores, which have a great influence on the absorption properties of the base paper. Hydrophobic sizing reduces this absorption and prevents binder migration efficiently. High surface roughness and especially poor formation of the base paper deteriorate thespray coated paper properties. However, pre-calendering of the base paper does not contribute anything to the finished paper quality, at least at the coating colour solids level below 60 %. When targeting a standard offset LWC grade, spraycoating produces similar quality to film coating, but yet blade coating being on a slightly better level. However, because of the savings in both investment and production costs, spray coating may have an excellent future ahead. The porousnature of the spray coated surface offers an optimum substrate for the coldset printing industry to utilise the potential of high quality papers in their business.

Critical flux and fouling in ultrafiltration of proteins

In this thesis different parameters influencing critical flux in protein ultrafiltration and membrane foul-ing were studied. Short reviews of proteins, cross-flow ultrafiltration, flux decline and criticalflux and the basic theory of Partial Least Square analysis (PLS) are given at the beginning. The experiments were mainly performed using dilute solutions of globular proteins, commercial polymeric membranes and laboratory scale apparatuses. Fouling was studied by flux, streaming potential and FTIR-ATR measurements. Critical flux was evaluated by different kinds of stepwise procedures and by both con-stant pressure and constant flux methods. The critical flux was affected by transmembrane pressure, flow velocity, protein concentration, mem-brane hydrophobicity and protein and membrane charges. Generally, the lowest critical fluxes were obtained at the isoelectric points of the protein and the highest in the presence of electrostatic repulsion between the membrane surface and the protein molecules. In the laminar flow regime the critical flux increased with flow velocity, but not any more above this region. An increase in concentration de-creased the critical flux. Hydrophobic membranes showed fouling in all charge conditionsand, furthermore, especially at the beginning of the experiment even at very low transmembrane pressures. Fouling of these membranes was thought to be due to protein adsorption by hydrophobic interactions. The hydrophilic membranes used suffered more from reversible fouling and concentration polarisation than from irreversible foul-ing. They became fouled at higher transmembrane pressures becauseof pore blocking. In this thesis some new aspects on critical flux are presented that are important for ultrafiltration and fractionation of proteins.

Siistausmassan saostuksessa kiekkosuodattimella käytettävän suodatinväliaineen testaus ja kehittäminen

Työn aiheena on siistausmassan saostuksessa käytettävä kiekkosuodatinväliaine ja tarkoituksena selvittää lankamateriaalien ja pinnoitusaineiden vaikutusta väliaineen likaantumisherkkyyteen ja suodatusteknisiin ominaisuuksiin. Siistauslaitosten ongelmana on suodatinväliaineen likaantuminen massassa olevien tahmo- ja painoväripartikkelien johdosta. Tällä hetkellä siistauslaitosten kiekkosuodatinpussien valmistuksessa käytetään pääasiassa polypropeeni- ja polyvinylideenifluoridimonofilamenttilankoja, joiden lianhylkivyys on osoittautunut huonoksi. Uusiksi lankamateriaaleiksi tutkimuksiin valittiin Easy Kleen I, Easy Kleen II, Hyflon, Halar ja Polyesteri. Tulosten perusteella Easy Kleen I ja II monofilamenttilangoista kudotun suodatinkankaan lianhylkivyys on polypropeeni- ja polyvinylideenifluoridimonofilamenttilangoista kudottua kangasta parempi. Suodatusteknisissä ominaisuuksissa ei materiaalien välillä havaittu merkittävää eroa. Easy Kleen monofilamenttilangat näyttävät soveltuvan myös keittokutistumiltaan ja mekaanisilta ominaisuuksiltaan kiekkosuodatinpussien materiaaleiksi. Polypropeeni- ja polyesterimonofilamenettilangoista kudottujen suodatinkankaiden pinnoittamisessa käytettiin hydrofiilisiä ja hydrofobisia pinnoitusaineita. Tulosten perusteella on mahdollista parantaa suodatinkankaan lianhylkivyyttä pinnoittamalla. Pinnoitettu kangas on myös suodatusteknisiltä ominaisuuksiltaan toimiva. Ongelmaksi suodatinkankaiden pinnoittamisessa saattaa kuitenkin muodostua pinnoituslämpötila, jossa kangas kutistuu asennuskelvottomaksi.

Process intensification: From optimised flow patterns to microprocess technology

This thesis is focused on process intensification. Several significant problems and applications of this theme are covered. Process intensification is nowadays one of the most popular trends in chemical engineering and attempts have been made to develop a general, systematic methodology for intensification. This seems, however, to be very difficult, because intensified processes are often based on creativity and novel ideas. Monolith reactors and microreactors are successful examples of process intensification. They are usually multichannel devices in which a proper feed technique is important for creating even fluid distribution into the channels. Two different feed techniques were tested for monoliths. In the first technique a shower method was implemented by means of perforated plates. The second technique was a dispersion method using static mixers. Both techniques offered stable operation and uniform fluid distribution. The dispersion method enabled a wider operational range in terms of liquid superficial velocity. Using dispersion method, a volumetric gas-liquid mass transfer coefficient of 2 s-1 was reached. Flow patterns play a significant role in terms of the mixing performance of micromixers. Although the geometry of a T-mixer is simple, channel configurations and dimensions had a clear effect on mixing efficiency. The flow in the microchannel was laminar, but the formation of vortices promoted mixing in micro T-mixers. The generation of vortices was dependent on the channel dimensions, configurations and flow rate. Microreactors offer a high ratio of surface area to volume. Surface forces and interactions between fluids and surfaces are, therefore, often dominant factors. In certain cases, the interactions can be effectively utilised. Different wetting properties of solid materials (PTFE and stainless steel) were applied in the separation of immiscible liquid phases. A micro-scale plate coalescer with hydrophilic and hydrophobic surfaces was used for the continuous separation of organic and aqueous phases. Complete phase separation occurred in less than 20 seconds, whereas the separation time by settling exceeded 30 min. Fluid flows can be also intensified in suitable conditions. By adding certain additives into turbulent fluid flow, it was possible to reduce friction (drag) by 40 %. Drag reduction decreases frictional pressure drop in pipelines which leads to remarkable energy savings and decreases the size or number of pumping facilities required, e.g., in oil transport pipes. Process intensification enables operation often under more optimal conditions. The consequent cost savings from reduced use of raw materials and reduced waste lead to greater economic benefits in processing.

Fouling management and retention in nanofiltration of integrated paper mill effluents

Nanofiltration performance was studied with effluents from the pulp and paper industry and with model substances. The effect of filtration conditions and membrane properties on nanofiltration flux, retention, and fouling was investigated. Generally, the aim was to determine the parameters that influence nanofiltration efficiency and study how to carry out nanofiltration without fouling by controlling these parameters. The retentions of the nanofiltration membranes studied were considerably higher than those of tight ultrafiltration membranes, and the permeate fluxes obtained were approximately the same as those of tight ultrafiltration membranes. Generally, about 80% retentions of total carbon and conductivity were obtained during the nanofiltration experiments. Depending on the membrane and the filtration conditions, the retentions of monovalent ions (chloride) were between 80 and 95% in the nanofiltrations. An increase in pH improved retentions considerably and also the flux to some degree. An increase in pressure improved retention, whereas an increase in temperature decreased retention if the membrane retained the solute by the solution diffusion mechanism. In this study, more open membranes fouled more than tighter membranes due to higher concentration polarization and plugging of the membrane material. More irreversible fouling was measured for hydrophobic membranes. Electrostatic repulsion between the membrane and the components in the solution reduced fouling but did not completely prevent it with the hydrophobic membranes. Nanofiltration could be carried out without fouling, at least with the laboratory scale apparatus used here when the flux was below the critical flux. Model substances had a strong form of the critical flux, but the effluents had only a weak form of the critical flux. With the effluents, some fouling always occurred immediately when the filtration was started. However, if the flux was below the critical flux, further fouling was not observed. The flow velocity and pH were probably the most important parameters, along with the membrane properties, that influenced the critical flux. Precleaning of the membranes had only a small effect on the critical flux and retentions, but it improved the permeability of the membranes significantly.

Vaahdonestokemikaalin syöttötapahtuman tehostamisen vaikutus märkäosan toimintaan

An improved defoamer dosage procedure and a more efficient dosing point to the approach system were studied in this thesis. Their influence on paper machine wet end operations was investigated. The improved defoamer dosing procedure was examined at UMP-Kymmene Tervasaari PM8. Air content and its controlling methods at the paper machine were studied in the literature survey. Also the influence of dissolved gases and entrained air in the papermaking furnish were introduced. Feeding methods – a TrumpJet chemical mixer and traditional feeding devices – were reviewed. The defoamer’s functioning methods were studied. The influence of the use of defoamers was estimated based on the main selected wet end operations. In the experimental part, defoamer mixing with a traditional feeding method and two improved mixing stages were compared based on the air content profiles in PM8’s approach system. The reference dosage procedure was PM8’s old dosing system. The first dosage procedure in the comparison involved two TrumpJet chemical mixers installed on the bottom wire trays. The second element of comparison involved the improvement brought by a third TrumpJet chemical mixer installed on the top wire tray. This second comparison of the efficient defoamer feeding concept was made at a higher production speed of PM8. The air content control situation was also studied at the higher production speed. In addition the connection between the defoamer and air content was observed and a mill-scale system was studied. The economical benefits of the new dosing procedure were also reviewed. Air content profiles of short circulation were measured in the reference situation and the two comparison points of the study. These air content measurements proved the main gas load is introduced to PM8's paper furnish from the white water tray. Thick stock air content was not essential when the air volume flow was considered. The improved defoamer dosing procedure made lower dosage amounts possible. Compared with the traditional feeding system, the new defoamer feeding concept made only few direct improvements to the wet end operations and the produced paper itself. The lower defoamer need was noticed to have a positive influence on hydrophobic sizing and paper defects. The surfaces of the white water tanks and the operation of pumps were assessed based on the density variations of the suspension. The temperature in the white water silo was stated to have a significant influence on the air content measured in the first centrifugal cleaning stage.

Effects of Surface Properties and Wood Modification into Direct Printing on Wood

Building industry is a high volume branch which could provide prominent markets for wood based interior decoration solutions. Competition in interior decoration markets requires versatility in appearance. Versatility in wood appearance and added value could be achieved by printing grain patterns of different species or images directly onto wood. The problem when planning wood printing’s implementing into durable applications is basically how to transfer a high quality image or print sustainably onto wood, which is porous, heterogeneous, dimensionally unstable, non-white and rough. Wood preservation or treating, and modification can provide durability against degradation but also effect to the surface properties of wood which will effect on printability. Optimal adhesion is essential into print quality, as too high ink absorbance can cause spreading and too low ink absorbance cause pale prints. Different printing techniques have different requirements on materials and production. The direct printing on wood means, that intermedias are not used. Printing techniques with flexible printing plates or in fact non-impact techniques provide the best basis for wood printing. Inkjet printing of wood with different mechanical or chemical surface treatments, and wood plastic composite material gave good results that encourage further studies of the subject. Sanding the wood surface anti-parallel to the grain gave the best overall printing quality. Spreading parallel to the grain could not be avoided totally, except in cases where wood was treated hydrophobic so adhesion of the ink was not sufficient. Grain pattern of the underlying wood stays clearly visible in the printed images. Further studies should be made to fine tune the methods that already gave good results. Also effects of moisture content of wood, different inks, and long-term exposure to UV-radiation should be tested.

Risto Näätäsen löytämällä aivoaallolla runsaasti sovelluksia

Mismatch negativity eli MMN-aivoaaltoon pohjaava aivotutkimus on levinnyt ympäri maailman.

Visualization of communication system testing logs

During the past decades testing has matured from ad-hoc activity into being an integral part of the development process. The benefits of testing are obvious for modern communication systems, which operate in heterogeneous environments amongst devices from various manufacturers. The increased demand for testing also creates demand for tools and technologies that support and automate testing activities. This thesis discusses applicability of visualization techniques in the result analysis part of the testing process. Particularly, the primary focus of this work is visualization of test execution logs produced by a TTCN-3 test system. TTCN-3 is an internationally standardized test specification and implementation language. The TTCN-3 standard suite includes specification of a test logging interface and a graphical presentation format, but no immediate relationship between them. This thesis presents a technique for mapping the log events to the graphical presentation format along with a concrete implementation, which is integrated with the Eclipse Platform and the OpenTTCN Tester toolchain. Results of this work indicate that for majority of the log events, a visual representation may be derived from the TTCN-3 standard suite. The remaining events were analysed and three categories relevant in either log analysis or implementation of the visualization tool were identified: events indicating insertion of something into the incoming queue of a port, events indicating a mismatch and events describing the control flow during the execution. Applicability of the results is limited into the domain of TTCN-3, but the developed mapping and the implementation may be utilized with any TTCN-3 tool that is able to produce the execution log in the standardized XML format.

Influence of plasma modification on surface properties and offset printability of coated paper

The properties of the paper surface play a crucial role in ensuring suitable quality and runnability in various converting and finishing operations, such as printing. Plasma surface modification makes it possible to modify the surface chemistry of paper without altering the bulk material properties. This also makes it possible to investigate the role of the surface chemistry alone on printability without influencing the porous structure of the pigment-coated paper. Since the porous structure of a pigment coating controls both ink setting and optical properties, surface chemical changes created by a plasma modification have a potential to decouple these two effects and to permit a better optimization of them both. The aim of this work was to understand the effects of plasma surface modification on paper properties, and how it influences printability in the sheet-fed offset process. The objective was to broaden the fundamental understanding of the role of surface chemistry on offset printing. The effects of changing the hydrophilicity/ hydrophobicity and the surface chemical composition by plasma activation and plasma coatings on the properties of coated paper and on ink-paper interactions as well as on sheet-fed offset print quality were investigated. In addition, the durability of the plasma surface modification was studied. Nowadays, a typical sheet-fed offset press also contains units for surface finishing, for example UVvarnishing. The role of the surface chemistry on the UV-varnish absorption into highly permeable and porous pigment-coated paper was also investigated. With plasma activation it was possible to increase the surface energy and hydrophilicity of paper. Both polar and dispersion interactions were found to increase, although the change was greater in the polar interactions due to induced oxygen molecular groups. The results indicated that plasma activation takes place particularly in high molecular weight components such as the dispersion chemicals used to stabilize the pigment and latex particles. Surface composition, such as pigment and binder type, was found to influence the response to the plasma activation. The general trend was that pilot-scale treatment modified the surface chemistry without altering the physical coating structure, whereas excessive laboratory-scale treatment increased the surface roughness and reduced the surface strength, which led to micro-picking in printing. It was shown that pilot-scale plasma activation in combination with appropriate ink oils makes it possible to adjust the ink-setting rate. The ink-setting rate decreased with linseed-oil-based inks, probably due to increased acid-base interactions between the polar groups in the oil and the plasma-treated paper surface. With mineral-oil-based inks, the ink setting accelerated due to plasma activation. Hydrophobic plasma coatings were able to reduce or even prevent the absorption of dampening water into pigmentcoated paper, even when the dampening water was applied under the influence of nip pressure. A uniform hydrophobic plasma coating with sufficient chemical affinity with ink gave an improved print quality in terms of higher print density and lower print mottle. It was also shown that a fluorocarbon plasma coating reduced the free wetting of the UV-varnish into the highly permeable and porous pigment coating. However, when the UV-varnish was applied under the influence of nip pressure, which leads to forced wetting, the role of the surface chemical composition seems to be much less. A decay in surface energy and wettability occurred during the first weeks of storage after plasma activation, after which it leveled off. However, the oxygen/carbon elemental ratio did not decrease as a function of time, indicating that ageing could be caused by a re-orientation of polar groups or by a contamination of the surface. The plasma coatings appeared to be more stable when the hydrophobicity was higher, probably due to fewer interactions with oxygen and water vapor in the air.