Formation and Control of Trace Metal Emissions in Co-Firing of Biomass, Peat, and Wastes in Fluidised Bed Combustors

Environmentally harmful consequences of fossil fuel utilisation andthe landfilling of wastes have increased the interest among the energy producers to consider the use of alternative fuels like wood fuels and Refuse-Derived Fuels, RDFs. The fluidised bed technology that allows the flexible use of a variety of different fuels is commonly used at small- and medium-sized power plants ofmunicipalities and industry in Finland. Since there is only one mass-burn plantcurrently in operation in the country and no intention to build new ones, the co-firing of pre-processed wastes in fluidised bed boilers has become the most generally applied waste-to-energy concept in Finland. The recently validated EU Directive on Incineration of Wastes aims to mitigate environmentally harmful pollutants of waste incineration and co-incineration of wastes with conventional fuels. Apart from gaseous flue gas pollutants and dust, the emissions of toxic tracemetals are limited. The implementation of the Directive's restrictions in the Finnish legislation is assumed to limit the co-firing of waste fuels, due to the insufficient reduction of the regulated air pollutants in the existing flue gas cleaning devices. Trace metals emission formation and reduction in the ESP, the condensing wet scrubber, the fabric filter, and the humidification reactor were studied, experimentally, in full- and pilot-scale combustors utilising the bubbling fluidised bed technology, and, theoretically, by means of reactor model calculations. The core of the model is a thermodynamic equilibrium analysis. The experiments were carried out with wood chips, sawdust, and peat, and their refuse-derived fuel, RDF, blends. In all, ten different fuels or fuel blends were tested. Relatively high concentrations of trace metals in RDFs compared to the concentrations of these metals in wood fuels increased the trace metal concentrations in the flue gas after the boiler ten- to hundred-folds, when RDF was co-fired with sawdust in a full-scale BFB boiler. In the case of peat, lesser increase in trace metal concentrations was observed, due to the higher initial trace metal concentrations of peat compared to sawdust. Despite the high removal rate of most of the trace metals in the ESP, the Directive emission limits for trace metals were exceeded in each of the RDF co-firing tests. The dominat trace metals in fluegas after the ESP were Cu, Pb and Mn. In the condensing wet scrubber, the flue gas trace metal emissions were reduced below the Directive emission limits, whenRDF pellet was used as a co-firing fuel together with sawdust and peat. High chlorine content of the RDFs enhanced the mercuric chloride formation and hence the mercury removal in the ESP and scrubber. Mercury emissions were lower than theDirective emission limit for total Hg, 0.05 mg/Nm3, in all full-scale co-firingtests already in the flue gas after the ESP. The pilot-scale experiments with aBFB combustor equipped with a fabric filter revealed that the fabric filter alone is able to reduce the trace metal concentrations, including mercury, in the flue gas during the RDF co-firing approximately to the same level as they are during the wood chip firing. Lower trace metal emissions than the Directive limits were easily reached even with a 40% thermal share of RDF co-firing with sawdust.Enrichment of trace metals in the submicron fly ash particle fraction because of RDF co-firing was not observed in the test runs where sawdust was used as the main fuel. The combustion of RDF pellets with peat caused an enrichment of As, Cd, Co, Pb, Sb, and V in the submicron particle mode. Accumulation and release oftrace metals in the bed material was examined by means of a bed material analysis, mass balance calculations and a reactor model. Lead, zinc and copper were found to have a tendency to be accumulated in the bed material but also to have a tendency to be released from the bed material into the combustion gases, if the combustion conditions were changed. The concentration of the trace metal in the combustion gases of the bubbling fluidised bed boiler was found to be a summary of trace metal fluxes from three main sources. They were (1) the trace metal flux from the burning fuel particle (2) the trace metal flux from the ash in the bed, and (3) the trace metal flux from the active alkali metal layer on the sand (and ash) particles in the bed. The amount of chlorine in the system, the combustion temperature, the fuel ash composition and the saturation state of the bed material in regard to trace metals were discovered to be key factors affecting therelease process. During the co-firing of waste fuels with variable amounts of e.g. ash and chlorine, it is extremely important to consider the possible ongoingaccumulation and/or release of the trace metals in the bed, when determining the flue gas trace metal emissions. If the state of the combustion process in regard to trace metals accumulation and/or release in the bed material is not known,it may happen that emissions from the bed material rather than the combustion of the fuel in question are measured and reported.

Pyrolyysiöljyn tuottaminen kiertoleijukattilaan liitetyllä prosessilla

Pyrolyysiöljy on biomassasta nopealla hapettomalla lämpökäsittelyprosessilla saatavaa nestemäistä polttoainetta. Kasvavien uusiutuvan energian käyttötavoitteiden myötä pyrolyysiöljystä on tullut kiinnostava vaihtoehto fossiilisille polttoöljyille. Suurimmat käytön haasteet ovat alhainen lämpöarvo, korkeat kiintoainepitoisuudet ja happamuus fossiilisiin polttoöljyihin verrattuna sekä eri raaka-aineista syntyvät ominaisuuksiltaan erilaiset pyrolyysiöljyt. Pyrolyysiöljyn kaupallinen tuotanto on vasta käynnistymässä eikä sen laadulle ole olemassa standardeja, joten eri valmistajien tuotteet voivat poiketa toisistaan huomattavastikin. Suomessa on Valtion teknillisen tutkimuskeskuksen (VTT) toimesta kehitetty Integrated Thermal Process (ITP)-konsepti, jossa pyrolyysiöljyn tuotantoprosessi on liitetty kiertoleijukattilaprosessiin. Prosessien yhdistämisellä voidaan parantaa kokonaishyötysuhdetta sekä hyödyntää laitosten yhteistä käyttöä ja polttoaineen hankintaa. Pyrolyysiprosessin tarvitsema lämpöenergia otetaan petihiekan välityksellä kattilasta, jossa poltetaan myös prosessissa syntyvät oheistuotteet. Tässä diplomityössä tutkittiin pyrolyysiprosessin vaikutusta voimalaitoksen toimintaan ja luotiin malli voimalaitoksen energiataseessa tapahtuvien muutosten arviointiin. Malli laskee sekä pyrolysaattorin että raaka-aineen käsittelyn vaikutukset voimalaitoksen sähkön- ja lämmöntuotantoon. Lisäksi mallin avulla voidaan arvioida pyrolysaattorin aiheuttama raaka-aineen tarve sekä voimalaitoksen lisäpolttoaineen tarve. Työssä tarkasteltiin myös pyrolyysiöljyn ominaisuuksia ja käyttökohteita, sekä tarvittavia muutoksia olemassa olevaan voimalaitokseen. Lisäksi arvioitiin tuotannon kannattavuutta. Mallia sovellettiin esimerkkivoimalaitokseen, jossa on harkittu pyrolyysiöljyn tuotannon aloittamista. Laskelmien perusteella pyrolyysiöljyn tuotannolla on sähkön- ja lämmöntuotantoa alentava sekä polttoaineen tarvetta korottava vaikutus. Pyrolyysiprosessin lisääminen nostaa voimalaitoksen kokonaishyötysuhdetta. Suotuisissa olosuhteissa öljytuotanto ITP-konseptilla näyttäisi olevan taloudellisesti kannattavaa.

Effect of forest-based biofuels production on carbon footprint, Case: Integrated LWC paper mill

International energy and climate strategies also set Finland’s commitments to increasing the use of renewable energy sources and reducing greenhouse gas emissions. The target can be achieved by, for example, increasing the use of energy wood. Finland’s forest biomass potential is significant compared with current use. Increased use will change forest management and wood harvesting methods however. The thesis examined the potential for integrated pulp and paper mills to increase bioenergy production. The effects of two bioenergy production technologies on the carbon footprint of an integrated LWC mill were studied at mill level and from the cradle-to-customer approach. The LignoBoost process and FT diesel production were chosen as bioenergy cases. The data for the LignoBoost process were obtained from Metso and for the FT diesel process from Neste Oil. The rest of the information is based on the literature and databases of the KCL-ECO life-cycle computer program and Ecoinvent. In both case studies, the carbon footprint was reduced. From the results, it can be concluded that it is possible to achieve a fossil-fuel-free pulp mill with the LignoBoost process. By using steam from the FT diesel process, the amount of auxiliary fuel can be reduced considerably and the bark boiler can be replaced. With a choice of auxiliary fuels for use in heat production in the paper mill and the production methods for purchased electricity, it is possible to affect the carbon footprints even more in both cases.

Vertailu kahden erityyppisen virtasyötetyn hakkurin soveltuvuudesta polttokennokäyttöihin

Concerns about condition of the environment and rising fossil fuel prices have accelerated the research of finding new cheap and environmental friendly energy source. Fuel cells are one of the most promising green technologies, especially in the field of distributed energy generation, backup power systems, transportation and mobile power generation. In this bachelor’s thesis use of fuel cells is studied, especially from the DC-DC converter point of view. This bachelor’s thesis concentrates on study of two different DC-DC converters. The aim of this thesis is to study design and steering methods for proposed converters. The ultimate aim of this thesis is to determine which one of proposed converters is most suitable for fuel cell applications.

Hakkuutähteestä valmistetun pyrolyysiöljyn elinkaaren kasvihuonekaasupäästöt

Kasvihuonekaasupäästöjen vähentämiseksi ja uusiutuvan energian käytön lisäämiseksi EU:ssa on säädetty direktiivi uusiutuvan energian käytön edistämisestä(RES-direktiivi). Direktiivissä annetaan ohjeet biopolttoaineiden ja bionesteiden kasvihuonekaasuvaikutusten laskemiseen. Tämän työn tarkoituksena oli selvittää, täyttääkö hakkuutähteistä valmistettu pyrolyysiöljy RES-direktiivin asettamat määrälliset vaatimukset kasvihuonekaasujen päästövähennykselle silloin, kun pyrolyysiöljyllä korvataan raskasta polttoöljyä lämmöntuotannossa. Laskenta suorittiin direktiivin ohjeiden mukaan. Lisäksi työssä pohdittiin laskentamenetelmän soveltuvuutta pyrolyysiöljyn ilmastovaikutusten arviointiin yleisesti. Laskennassa huomioitiin raaka-aineen tuotannosta, jalostuksesta sekä kuljetuksesta ja jakelusta aiheutuvat kasvihuonekaasupäästöt. Päästöt laskettiin ensin oletusarvoilla, jonka jälkeen suoritettiin todennäköisyyspohjainen herkkyystarkastelu valituille parametreille. Herkkyystarkastelun tuloksista huomattiin, että päästövähennys riippuu pääasiassa kahdesta tekijästä: maaperän hiilitaseen muutoksesta aiheutuvista päästöistä ja pyrolyysiprosessin tarvitseman lämmön tuotantoon käytetyistä polttoaineista. Eniten tuloksiin vaikutti kuitenkin se, oletettiinko pyrolysaattori ja kattila tarkastelussa erillisiksi yksiköiksi (tapaus 1) vai kokonaisuudeksi (tapaus 2). Tulosten perusteella näyttää siltä, että pyrolyysiöljyn käyttö lämmöntuotannossa raskaan polttoöljyn sijasta johtaa päästövähennyksiin. Saatuja tuloksia ei kuitenkaan voida pitää ennusteina pyrolyysiöljyn todellisista ilmastovaikutuksista, koska elinkaariarviointiin liittyy monia epävarmuuksia. RES-direktiivin laskentaohjeet esimerkiksi järjestelmärajausten muodostamisesta ja päästöjen kohdentamisesta ovat epätarkat. Tästä syystä direktiiviä on mahdollista tulkita usealla eri tavalla, jolloin toisistaan poikkeavat tulokset voivat silti olla kaikki direktiivin mukaisesti laskettuja. Jotta liika tulkinnanvaraisuus ei aiheuttaisi ongelmia, olisi RES-direktiivin laskentaohjetta hyvä tarkentaa.

Diskreettiaikainen liukuvan moodin säätö kiinteäoksidipolttokennon DC-tasonnostossa

Huoli ympäristön tilasta ja fossiilisten polttoaineiden hinnan nousu ovat vauhdittaneet tutkimusta uusien energialähteiden löytämiseksi. Polttokennot ovat yksi lupaavimmista tekniikoista etenkin hajautetun energiantuotannon, varavoimalaitosten sekä liikennevälineiden alueella. Polttokenno on tehonlähteenä kuitenkin hyvin epäideaalinen, ja se asettaa tehoelektroniikalle lukuisia erityisvaatimuksia. Polttokennon kytkeminen sähköverkkoon on tavallisesti toteutettu käyttämällä galvaanisesti erottavaa DC/DC hakkuria sekä vaihtosuuntaajaa sarjassa. Polttokennon kulumisen estämiseksi tehoelektroniikalta vaaditaan tarkkaa polttokennon lähtövirran hallintaa. Perinteisesti virran hallinta on toteutettu säätämällä hakkurin tulovirtaa PI (Proportional and Integral) tai PID (Proportional, Integral and Derivative) -säätimellä. Hakkurin epälineaarisuudesta johtuen tällainen ratkaisu ei välttämättä toimi kaukana linearisointipisteestä. Lisäksi perinteiset säätimet ovat herkkiä mallinnusvirheille. Tässä diplomityössä on esitetty polttokennon jännitettä nostavan hakkurin tilayhtälökeskiarvoistusmenetelmään perustuva malli, sekä malliin perustuva diskreettiaikainen integroiva liukuvan moodin säätö. Esitetty säätö on luonteeltaan epälineaarinen ja se soveltuu epälineaaristen ja heikosti tunnettujen järjestelmien säätämiseen.

Nopeaan pyrolyysiin perustuvan bioöljyn tuotantolaitoksen liiketoiminnallinen malli ja kannattavuuslaskenta Savonlinnan seudulla

Pyrolyysiöljy on biomassasta nopealla hapettomalla lämpökäsittelyprosessilla valmistettavaa nestemäistä polttoainetta. Kasvavien uusiutuvan energian käyttötavoitteiden myötä pyrolyysiöljystä on tullut varteenotettava vaihtoehto fossiilisille polttoöljyille. Suurimmat käytön haasteet ovat alhainen lämpöarvo, happamuus ja korkeahkot kiintoainepitoisuudet verrattuna fossiilisiin polttoöljyihin. Nämä haasteet ovat kuitenkin ratkaistavissa. Työssä tarkasteltiin bioöljyn tuotantolaitoksen liiketoiminnallista mallia ja kannattavuutta Savonlinnan seudulle sijoitettuna. Tätä varten selvitettiin alueellinen raaka-aineen saatavuus ja hinta, sekä potentiaaliset markkinat pyrolyysiöljylle. Kannattavuuslaskentaa varten luotiin exel – pohjainen laskentatyökalu, jolla laskettiin pyrolyysiöljyn tuotannon omakustannushinnat ja kannattavuudet eri laitosvaihtoehdoille. Saaduille tuloksille tehtiin herkkyysanalyysi, jolla selvitettiin merkittävimmät kannattavuuteen vaikuttavat tekijät. Laskettujen tulosten perusteella pienemmät 100 BDMTPD (Bone Dry Metric Ton per Day) tuotantolaitokset eivät ole kannattavia investointeja. Suuremmat 400 BDMTPD tuotantolaitokset ovat kannattavia, kunhan raaka-aine saadaan kohtuulliseen hintaan ja investointikustannukset pysyvät kurissa.

Advanced welding technologies used for arctic metal structures

Rapid depletion of easy-to-access fossil fuel, predominantly, oil and gas resources has now necessitated increase in need to develop new oil and gas sources in ever more remote and hostile environments. This is necessary in order to explore more oil and gas resources to meet rapidly rising long-term energy demand in the world, both at present and in the nearest future. Arctic is one of these harsh environments, where enormous oil and gas resources are available, containing about 20% of the world total oil and gas, but the environmental conditions are very harsh and hostile. However, virtually all the facilities required for the exploration and development of this new energy source are constructed with metals as well as their alloys and are predominantly joined together by welding processes and technologies. Meanwhile, due to entirely different environment from the usual moderate temperate region, conventional welding technologies, common metals and their alloys cannot be applied as this Arctic environment demand metals structures with very high toughness and strength properties under extremely low temperature. This is due to the fact that metals transit from ductility to brittleness as the temperature moves toward extreme negative values. Hence, this research work investigates and presents the advanced welding technologies applicable to Arctic metal structures which can give satisfactory weldments under active Arctic service conditions. .

Pienen kokoluokan CHP-tuotannon kannattavuus kunnallisen lämpölaitoksen yhteydessä

Fossiiliset polttoainevarannot ovat ehtymässä. Nykyisen talouskasvumme perustuessa fossiilisten polttoaineiden kestämättömään käyttöön, on energiantuotantorakenteen muututtava. Euroopan Unioni on asettanut tavoitteet uusiutuvan energian osuuden lisäämiseksi. Näistä syistä johtuen kiinnostus uusiutuvaa energiaa ja hajautettua energiantuotantoa kohtaan on kasvanut viime aikoina. Tämän globaalin ilmiön rinnalla yhteiskuntarakenteen muutos Suomessa on johtanut tilanteeseen, jossa taloudellinen aktiviteetti kasvukeskusten ulkopuolella on hiipumassa. Loogisena ratkaisumallina on syntynyt hankkeita kuten Keski-Karjalan Kehitysyhtiö Oy:n Puhos 2013 - ympäristöalasta uutta liiketoimintaa - hanke. Tämä työ on Puhos 2013 - hankkeeseen tilattu tutkimus, jonka tavoitteena on puuta ja biokaasua polttoaineenaan käyttävän mikroturbiinitekniikkaan pohjautuvan pienen kokoluokan CHP tuotannon kannattavuuden selvittäminen kunnallisen lämpölaitoksen yhteydessä. Tutkimuksessa selvitettiin aluksi pienen kokoluokan CHP tuotannon kannattavuuteen vaikuttavat tekijät, jonka jälkeen opittua tietoa sovellettiin Kiteen Lämmön Arppentien lämpölaitoksen tapaukseen. Kiteen Lämmön taloudellisen kannattavuuden ohella tutkimuksessa huomioitiin uusien liiketoiminta mahdollisuuksien syntyminen alueelle. Käytetyt tutkimusmenetelmät olivat kvalitatiivinen analyysi ja perinteinen investoinnin kannattavuuslaskenta. Tutkimuksen tuloksena muodostettiin strategia, joka maksimoi molemmat edellä mainitut kannattavuuden näkökulmat. Kehitetyn strategian Kiteen Lämmön tulosta maksimoiva osuus muodostuu oman käyttösähkön tuottamisen aloittamisesta Arppentien lämpölaitoksella 30 kWe mikroturbiinilla käyttäen polttoaineena Bio10 Oy:n toimittamaa biokaasua. Uusien liiketoiminta mahdollisuuksien synty alueelle mahdollistetaan puolestaan kehittämällä puun kaasutukseen perustuva modulaarinen CHP laitos yhteistyössä Mekrijärven tutkimusaseman ja suomalaisten laitevalmistajien kanssa.

Theoretical Analysis and Numerical Simulation of Spectral Radiative Properties of Combustion Gases in Oxy/Air-Fired Combustion Systems

Energy efficiency is one of the major objectives which should be achieved in order to implement the limited energy resources of the world in a sustainable way. Since radiative heat transfer is the dominant heat transfer mechanism in most of fossil fuel combustion systems, more accurate insight and models may cause improvement in the energy efficiency of the new designed combustion systems. The radiative properties of combustion gases are highly wavelength dependent. Better models for calculating the radiative properties of combustion gases are highly required in the modeling of large scale industrial combustion systems. With detailed knowledge of spectral radiative properties of gases, the modeling of combustion processes in the different applications can be more accurate. In order to propose a new method for effective non gray modeling of radiative heat transfer in combustion systems, different models for the spectral properties of gases including SNBM, EWBM, and WSGGM have been studied in this research. Using this detailed analysis of different approaches, the thesis presents new methods for gray and non gray radiative heat transfer modeling in homogeneous and inhomogeneous H2O–CO2 mixtures at atmospheric pressure. The proposed method is able to support the modeling of a wide range of combustion systems including the oxy-fired combustion scenario. The new methods are based on implementing some pre-obtained correlations for the total emissivity and band absorption coefficient of H2O–CO2 mixtures in different temperatures, gas compositions, and optical path lengths. They can be easily used within any commercial CFD software for radiative heat transfer modeling resulting in more accurate, simple, and fast calculations. The new methods were successfully used in CFD modeling by applying them to industrial scale backpass channel under oxy-fired conditions. The developed approaches are more accurate compared with other methods; moreover, they can provide complete explanation and detailed analysis of the radiation heat transfer in different systems under different combustion conditions. The methods were verified by applying them to some benchmarks, and they showed a good level of accuracy and computational speed compared to other methods. Furthermore, the implementation of the suggested banded approach in CFD software is very easy and straightforward.

Waste-to-Energy Scenarios in the China Context

Waste incineration plants are increasingly established in China. A low heating value and high moisture content, due to a large proportion of biowaste in the municipal solid waste (MSW), can be regarded as typical characteristics of Chinese MSW. Two incineration technologies have been mainly established in China: stoker grate and circular fluidized bed (CFB). Both of them are designed to incinerate mixed MSW. However, there have been difficulties to reach the sufficient temperature in the combustion process due to the low heating value of the MSW. That is contributed to the usage of an auxiliary fossil fuel, which is often used during the whole incineration process. The objective of this study was to design alternative Waste-to-energy (WTE) scenarios for existing WTE plants with the aim to improve the material and energy efficiency as well as the feasibility of the plants. Moreover, the aim of this thesis was to find the key factors that affect to the feasibility of the scenarios. Five different WTE plants were selected as study targets. The necessary data for calculation was gained from literature as well as received from the operators of the target WTE plants. The created scenarios were based on mechanical-biological treatment (MBT) technologies, in which the produced solid recovered fuel (SRF) was fed as an auxiliary fuel into a WTE plant replacing the fossil fuel. The mechanically separated biowaste was treated either in an anaerobic digestion (AD) plant, a biodrying plant, a thermal drying plant, or a combined AD plant + thermal drying plant. An interactive excel spreadsheet based computation tool was designed to estimate the viability of the scenarios in different WTE cases. The key figures of the improved material and energy efficiency, such as additional electricity generated and avoided waste for landfill, were got as results. Furthermore, economic indicators such as annual profits (or costs), payback period, and internal rate of return (IRR) were gained as results. The results show that the AD scenario was the most profitable in most of the cases. The current heating value of MSW and the tipping fee for the received MSW appeared as the most important factor in terms of feasibility.

Fast pyrolysis in circulating fluidized bed: feasibility study

Today the limitedness of fossil fuel resources is clearly realized. For this reason there is a strong focus throughout the world on shifting from fossil fuel based energy system to biofuel based energy system. In this respect Finland with its proven excellent forestry capabilities has a great potential to accomplish this goal. It is regarded that one of the most efficient ways of wood biomass utilization is to use it as a feedstock for fast pyrolysis process. By means of this process solid biomass is converted into liquid fuel called bio-oil which can be burnt at power plants, used for hydrogen generation through a catalytic steam reforming process and as a source of valuable chemical compounds. Nowadays different configurations of this process have found their applications in several pilot plants worldwide. However the circulating fluidized bed configuration is regarded as the one with the highest potential to be commercialized. In the current Master’s Thesis a feasibility study of circulating fluidized bed fast pyrolysis process utilizing Scots pine logs as a raw material was conducted. The production capacity of the process is 100 000 tonne/year of bio-oil. The feasibility study is divided into two phases: a process design phase and economic feasibility analysis phase. The process design phase consists of mass and heat balance calculations, equipment sizing, estimation of pressure drops in the pipelines and development of plant layout. This phase resulted in creation of process flow diagrams, equipment list and Microsoft Excel spreadsheet that calculates the process mass and heat balances depending on the bio-oil production capacity which can be set by a user. These documents are presented in the current report as appendices. In the economic feasibility analysis phase there were at first calculated investment and operating costs of the process. Then using these costs there was calculated the price of bio-oil which is required to reach the values of internal rate of return of 5%, 10%, 20%, 30%, 40%, and 50%.

Characterisation of waste for combustion : with special reference to the role of zinc

Waste combustion has gone from being a volume reducing discarding-method to an energy recovery process for unwanted material that cannot be reused or recycled. Different fractions of waste are used as fuel today, such as; municipal solid waste, refuse derived fuel, and solid recovered fuel. Furthermore, industrial waste, normally a mixture between commercial waste and building and demolition waste, is common, either as separate fuels or mixed with, for example, municipal solid waste. Compared to fossil or biomass fuels, waste mixtures are extremely heterogeneous, making it a complicated fuel. Differences in calorific values, ash content, moisture content, and changing levels of elements, such as Cl and alkali metals, are common in waste fuel. Moreover, waste contains much higher levels of troublesome trace elements, such as Zn, which is thought to accelerate a corrosion process. Varying fuel quality can be strenuous on the boiler system and may cause fouling and corrosion of heat exchanger surfaces. This thesis examines waste fuels and waste combustion from different angles, with the objective of giving a better understanding of waste as an important fuel in today’s fuel economy. Several chemical characterisation campaigns of waste fuels over longer time periods (10-12 months) was used to determine the fossil content of Swedish waste fuels, to investigate possible seasonal variations, and to study the presence of Zn in waste. Data from the characterisation campaigns were used for thermodynamic equilibrium calculations to follow trends and determine the effect of changing concentrations of various elements. The thesis also includes a study of the thermal behaviour of Zn and a full—scale study of how the bed temperature affects the volatilisation of alkali metals and Zn from the fuel. As mixed waste fuel contains considerable amounts of fresh biomass, such as wood, food waste, paper etc. it would be wrong to classify it as a fossil fuel. When Sweden introduced waste combustion as a part of the European Union emission trading system in the beginning of 2013 there was a need for combustion plants to find a usable and reliable method to determine the fossil content. Four different methods were studied in full-scale of seven combustion plants; 14Canalysis of solid waste, 14C-analysis of flue gas, sorting analysis followed by calculations, and a patented balance method that is using a software program to calculate the fossil content based on parameters from the plant. The study showed that approximately one third of the coal in Swedish waste mixtures has fossil origins and presented the plants with information about the four different methods and their advantages and disadvantages. Characterisation campaigns also showed that industrial waste contain higher levels of trace elements, such as Zn. The content of Zn in Swedish waste fuels was determined to be approximately 800 mg kg-1 on average, based on 42 samples of solid waste from seven different plants with varying mixtures between municipal solid waste and industrial waste. A review study of the occurrence of Zn in fuels confirmed that the highest amounts of Zn are present in waste fuels rather than in fossil or biomass fuels. In tires, Zn is used as a vulcanizing agent and can reach concentration values of 9600-16800 mg kg-1. Waste Electrical and Electronic Equipment is the second Zn-richest fuel and even though on average Zn content is around 4000 mg kg-1, the values of over 19000 mg kg-1 were also reported. The increased amounts of Zn, 3000-4000 mg kg-1, are also found in municipal solid waste, sludge with over 2000 mg kg-1 on average (some exceptions up to 49000 mg kg-1), and other waste derived fuels (over 1000 mg kg-1). Zn is also found in fossil fuels. In coal, the average level of Zn is 100 mg kg-1, the higher amount of Zn was only reported for oil shale with values between 20-2680 mg kg-1. The content of Zn in biomass is basically determined by its natural occurrence and it is typically 10-100 mg kg-1. The thermal behaviour of Zn is of importance to understand the possible reactions taking place in the boiler. By using thermal analysis three common Zn-compounds were studied (ZnCl2, ZnSO4, and ZnO) and compared to phase diagrams produced with thermodynamic equilibrium calculations. The results of the study suggest that ZnCl2(s/l) cannot exist readily in the boiler due to its volatility at high temperatures and its conversion to ZnO in oxidising conditions. Also, ZnSO4 decomposes around 680°C, while ZnO is relatively stable in the temperature range prevailing in the boiler. Furthermore, by exposing ZnO to HCl in a hot environment (240-330°C) it was shown that chlorination of ZnO with HCl gas is possible. Waste fuel containing high levels of elements known to be corrosive, for example, Na and K in combination with Cl, and also significant amounts of trace elements, such as Zn, are demanding on the whole boiler system. A full-scale study of how the volatilisation of Na, K, and Zn is affected by the bed temperature in a fluidised bed boiler was performed parallel with a lab-scale study with the same conditions. The study showed that the fouling rate on deposit probes were decreased by 20 % when the bed temperature was decreased from 870°C to below 720°C. In addition, the lab-scale experiments clearly indicated that the amount of alkali metals and Zn volatilised depends on the reactor temperature.

The role of potassium in the corrosion of superheater materials in boilers firing biomass

Inhibition of global warming has become one of the major goals for the coming decades. A key strategy is to replace fossil fuels with more sustainable fuels, which has generated growing interest in the use of waste-derived fuels and of biomass fuels. However, from the chemical point of view, biomass is an inhomogeneous fuel, usually with a high concentration of water and considerable amounts of potassium and chlorine, all of which are known to affect the durability of superheater tubes. To slow down or reduce corrosion, power plants using biomass as fuel have been forced to operate at lower steam temperatures as compared to fossil fuel power plants. This reduces power production efficiency: every 10°C rise in the steam temperature results in an approximate increase of 2% in power production efficiency. More efficient ways to prevent corrosion are needed so that power plants using biomass and waste-derived fuels can operate at higher steam temperatures. The aim of this work was to shed more light on the alkali-induced corrosion of superheater steels at elevated temperatures, focusing on potassium chloride, the alkali salt most frequently encountered in biomass combustion, and on potassium carbonate, another potassium salt occasionally found in fly ash. The mechanisms of the reactions between various corrosive compounds and steels were investigated. Based on the results, the potassium-induced accelerated oxidation of chromia protected steels appears to occur in two consecutive stages. In the first, the protective chromium oxide layer is destroyed through a reaction with potassium leading to the formation of intermediates such as potassium chromate (K2CrO4) and depleting the chromium in the protective oxide layer. As the chromium is depleted, chromium from the bulk steel diffuses into the oxide layer to replenish it. In this stage, the ability of the material to withstand corrosion depends on the chromium content (which affects how long it takes the chromium in the oxide layer to be depleted) and on external factors such as temperature (which affects how fast the chromium diffuses into the protective oxide from the bulk steel). For accelerated oxidation to continue, the presence of chloride appears to be essential.

Commercialization of Modern Renewable Energy

The threat of global warming and its consequences are widely recognized, and the question of how to proceed with the long transition towards fossil fuel -neutral economies concerns many nations and people. At the same time the world’s primary energy use is predicted to increase significantly during the next decades as a result of global population and welfare increase. Improved energy efficiency and increased use of renewable energy sources in the world’s energy mix play important roles in the future energy production and consumption. The objective of this thesis is to study how novel renewable energy technologies, such as distributed small-scale bio-fueled combined heat and power production and wind power technologies could be commercialized efficiently. A wide array of attributes may contribute to the diffusion of new products. In general, the bioenergy and wind power technologies are in emerging phases, and the diffusion stage varies from country to country. The effects of firms’ technology choices, collaboration and alliances are studied in this thesis. Furthermore, the roles of national energy infrastructure and energy support schemes in the commercialization of new renewable energy products are explored. The empirical data is based on energy expert interviews, financial and patent data, and literature reviews of different case studies. The thesis comprises two parts. The first part provides an overview of the study, and the second part includes six research publications. The results reveal that small-scale bio-fueled combined heat and power production and wind power technologies are still in emerging phases in their life cycles, and energy support schemes are crucial in the market diffusion. The study contributes to earlier findings in the literature and industry by confirming that adequate energy policies and energy infrastructure are fundamental in the commercialization of novel renewable energy technologies. Firm-specific issues, including business relationships and new business models, and market-related issues will have a more significant role in the market penetration in the future, when the technologies mature and become competitive without political support schemes.