Formation and Control of Trace Metal Emissions in Co-Firing of Biomass, Peat, and Wastes in Fluidised Bed Combustors

Environmentally harmful consequences of fossil fuel utilisation andthe landfilling of wastes have increased the interest among the energy producers to consider the use of alternative fuels like wood fuels and Refuse-Derived Fuels, RDFs. The fluidised bed technology that allows the flexible use of a variety of different fuels is commonly used at small- and medium-sized power plants ofmunicipalities and industry in Finland. Since there is only one mass-burn plantcurrently in operation in the country and no intention to build new ones, the co-firing of pre-processed wastes in fluidised bed boilers has become the most generally applied waste-to-energy concept in Finland. The recently validated EU Directive on Incineration of Wastes aims to mitigate environmentally harmful pollutants of waste incineration and co-incineration of wastes with conventional fuels. Apart from gaseous flue gas pollutants and dust, the emissions of toxic tracemetals are limited. The implementation of the Directive's restrictions in the Finnish legislation is assumed to limit the co-firing of waste fuels, due to the insufficient reduction of the regulated air pollutants in the existing flue gas cleaning devices. Trace metals emission formation and reduction in the ESP, the condensing wet scrubber, the fabric filter, and the humidification reactor were studied, experimentally, in full- and pilot-scale combustors utilising the bubbling fluidised bed technology, and, theoretically, by means of reactor model calculations. The core of the model is a thermodynamic equilibrium analysis. The experiments were carried out with wood chips, sawdust, and peat, and their refuse-derived fuel, RDF, blends. In all, ten different fuels or fuel blends were tested. Relatively high concentrations of trace metals in RDFs compared to the concentrations of these metals in wood fuels increased the trace metal concentrations in the flue gas after the boiler ten- to hundred-folds, when RDF was co-fired with sawdust in a full-scale BFB boiler. In the case of peat, lesser increase in trace metal concentrations was observed, due to the higher initial trace metal concentrations of peat compared to sawdust. Despite the high removal rate of most of the trace metals in the ESP, the Directive emission limits for trace metals were exceeded in each of the RDF co-firing tests. The dominat trace metals in fluegas after the ESP were Cu, Pb and Mn. In the condensing wet scrubber, the flue gas trace metal emissions were reduced below the Directive emission limits, whenRDF pellet was used as a co-firing fuel together with sawdust and peat. High chlorine content of the RDFs enhanced the mercuric chloride formation and hence the mercury removal in the ESP and scrubber. Mercury emissions were lower than theDirective emission limit for total Hg, 0.05 mg/Nm3, in all full-scale co-firingtests already in the flue gas after the ESP. The pilot-scale experiments with aBFB combustor equipped with a fabric filter revealed that the fabric filter alone is able to reduce the trace metal concentrations, including mercury, in the flue gas during the RDF co-firing approximately to the same level as they are during the wood chip firing. Lower trace metal emissions than the Directive limits were easily reached even with a 40% thermal share of RDF co-firing with sawdust.Enrichment of trace metals in the submicron fly ash particle fraction because of RDF co-firing was not observed in the test runs where sawdust was used as the main fuel. The combustion of RDF pellets with peat caused an enrichment of As, Cd, Co, Pb, Sb, and V in the submicron particle mode. Accumulation and release oftrace metals in the bed material was examined by means of a bed material analysis, mass balance calculations and a reactor model. Lead, zinc and copper were found to have a tendency to be accumulated in the bed material but also to have a tendency to be released from the bed material into the combustion gases, if the combustion conditions were changed. The concentration of the trace metal in the combustion gases of the bubbling fluidised bed boiler was found to be a summary of trace metal fluxes from three main sources. They were (1) the trace metal flux from the burning fuel particle (2) the trace metal flux from the ash in the bed, and (3) the trace metal flux from the active alkali metal layer on the sand (and ash) particles in the bed. The amount of chlorine in the system, the combustion temperature, the fuel ash composition and the saturation state of the bed material in regard to trace metals were discovered to be key factors affecting therelease process. During the co-firing of waste fuels with variable amounts of e.g. ash and chlorine, it is extremely important to consider the possible ongoingaccumulation and/or release of the trace metals in the bed, when determining the flue gas trace metal emissions. If the state of the combustion process in regard to trace metals accumulation and/or release in the bed material is not known,it may happen that emissions from the bed material rather than the combustion of the fuel in question are measured and reported.

Oxalic acid and calcium oxalate in production of wood-containing paper : formation, analysis, and control

Papperstillverkningen störs ofta av oönskade föreningar som kan bilda avsättningar på processytor, vilket i sin tur kan ge upphov till störningar i pappersproduktionen samt försämring av papperskvaliteten. Förutom avsättningar av vedharts är stenliknande avlagringar av svårlösliga salter vanliga. I vårt dagliga liv är kalkavlagringar i kaffe- och vattenkokare exempel på liknande problem. I massa- och pappersindustrin är en av de mest problematiska föreningarna kalciumoxalat; detta salt är nästan olösligt i vatten och avlagringarna är mycket svåra att avlägsna. Kalciumoxalat är också känt som en av orsakerna till njurstenar hos människor. Veden och speciellt barken innehåller alltid en viss mängd oxalat men en större källa är oxalsyra som bildas när massan bleks med oxiderande kemikalier, t.ex. väteperoxid. Kalciumoxalat bildas när oxalsyran reagerar med kalcium som kommer in i processen med råvattnet, veden eller olika tillsatsmedel. I denna avhandling undersöktes faktorer som påverkar bildningen av oxalsyra och utfällningen av kalciumoxalat, med hjälp av bleknings- och utfällningsexperiment. Forskningens fokus låg speciellt på olika sätt att förebygga uppkomsten av avlagringar vid tillverkning av trähaltigt papper. Resultaten i denna avhandling visar att bildningen av oxalsyra samt utfällning av kalciumoxalat kan påverkas genom processtekniska och våtändskemiska metoder. Noggrann avbarkning av veden, kontrollerade förhållanden under den alkaliska peroxidblekningen, noggrann hantering och kontroll av andra lösta och kolloidala substanser, samt utnyttjande av skräddarsydd kemi för kontroll av avlagringar är nyckelfaktorer. Resultaten kan utnyttjas då man planerar blekningssekvenser för olika massor samt för att lösa problem orsakade av kalciumoxalat. Forskningsmetoderna som användes i utfällningsstudierna samt för utvärdering av tillsatsmedel kan också utnyttjas inom andra områden, t.ex. bryggeri- och sockerindustrin, där kalciumoxalatproblem är vanligt förekommande. -------------------------------------------- Paperinvalmistusta häiritsevät usein erilaiset epäpuhtaudet, jotka kiinnittyvät prosessipinnoille ja haittaavat tuotantoa sekä paperin laatua. Puun pihkan lisäksi eräs yleinen ongelma on niukkaliukoisten suolojen aiheuttamat kivettymät. Kalkkisaostuma kahvinkeittimessä on esimerkki vastaavasta ongelmasta arkielämässä. Massa- ja paperiteollisuudessa yksi hankalimmista kivettymien muodostajista on kalsiumoksalaatti, koska se on lähes liukenematonta ja sen aiheuttamat saostumat ovat erittäin vaikeasti poistettavia. Kalsiumoksalaatti on yleisesti tunnettu myös munuaiskivien aiheuttajana ihmisillä. Puu ja varsinkin sen kuori sisältää aina jonkin verran oksalaattia, mutta suurempi lähde on kuitenkin oksaalihappo jota muodostuu valkaistaessa massaa hapettavilla kemikaaleilla, kuten vetyperoksidilla. Kalsiumoksalaattia syntyy kun veden, puun ja lisäaineiden mukana prosessiin tuleva kalsium reagoi oksalaatin kanssa. Tässä väitöskirjatyössä tutkittiin oksaalihapon muodostumiseen ja kalsiumoksalaatin saostumiseen vaikuttavia tekijöitä valkaisu- ja saostumiskokeiden avulla. Tutkimuksen painopiste oli saostumien ehkäisemisessä puupitoisten painopaperien valmistuksessa. Työssä saadut tulokset osoittavat että oksaalihapon muodostumiseen ja kalsiumoksalaatin saostumiseen voidaan vaikuttaa sekä prosessiteknisten että märänpään kemian keinojen avulla. Tehokas puun kuorinta, optimoidut olosuhteet peroksidivalkaisussa, muiden liuenneiden ja kolloidisten aineiden hallinta sekä räätälöidyn kemian hyödyntäminen kalsiumoksalaattisaostumien torjunnassa ovat keskeisissä rooleissa ongelmien välttämiseksi. Väitöskirjatyön tuloksia voidaan hyödyntää massan valkaisulinjoja suunniteltaessa sekä kalsiumoksalaatin aiheuttamien ongelmien ratkaisemisessa. Tutkimusmenetelmiä, joita käytettiin saostumiskokeissa ja eri lisäaineiden vaikutusten arvioinnissa, voidaan hyödyntää massa- ja paperiteollisuuden lisäksi myös muilla alueilla, kuten sokeri- ja panimoteollisuudessa, joissa ongelma on myös yleinen.

Effect of hydrodynamics on modelling, monitoring and control of crystallization

Crystallization is a purification method used to obtain crystalline product of a certain crystal size. It is one of the oldest industrial unit processes and commonly used in modern industry due to its good purification capability from rather impure solutions with reasonably low energy consumption. However, the process is extremely challenging to model and control because it involves inhomogeneous mixing and many simultaneous phenomena such as nucleation, crystal growth and agglomeration. All these phenomena are dependent on supersaturation, i.e. the difference between actual liquid phase concentration and solubility. Homogeneous mass and heat transfer in the crystallizer would greatly simplify modelling and control of crystallization processes, such conditions are, however, not the reality, especially in industrial scale processes. Consequently, the hydrodynamics of crystallizers, i.e. the combination of mixing, feed and product removal flows, and recycling of the suspension, needs to be thoroughly investigated. Understanding of hydrodynamics is important in crystallization, especially inlargerscale equipment where uniform flow conditions are difficult to attain. It is also important to understand different size scales of mixing; micro-, meso- and macromixing. Fast processes, like nucleation and chemical reactions, are typically highly dependent on micro- and mesomixing but macromixing, which equalizes the concentrations of all the species within the entire crystallizer, cannot be disregarded. This study investigates the influence of hydrodynamics on crystallization processes. Modelling of crystallizers with the mixed suspension mixed product removal (MSMPR) theory (ideal mixing), computational fluid dynamics (CFD), and a compartmental multiblock model is compared. The importance of proper verification of CFD and multiblock models is demonstrated. In addition, the influence of different hydrodynamic conditions on reactive crystallization process control is studied. Finally, the effect of extreme local supersaturation is studied using power ultrasound to initiate nucleation. The present work shows that mixing and chemical feeding conditions clearly affect induction time and cluster formation, nucleation, growth kinetics, and agglomeration. Consequently, the properties of crystalline end products, e.g. crystal size and crystal habit, can be influenced by management of mixing and feeding conditions. Impurities may have varying impacts on crystallization processes. As an example, manganese ions were shown to replace magnesium ions in the crystal lattice of magnesium sulphate heptahydrate, increasing the crystal growth rate significantly, whereas sodium ions showed no interaction at all. Modelling of continuous crystallization based on MSMPR theory showed that the model is feasible in a small laboratoryscale crystallizer, whereas in larger pilot- and industrial-scale crystallizers hydrodynamic effects should be taken into account. For that reason, CFD and multiblock modelling are shown to be effective tools for modelling crystallization with inhomogeneous mixing. The present work shows also that selection of the measurement point, or points in the case of multiprobe systems, is crucial when process analytical technology (PAT) is used to control larger scale crystallization. The thesis concludes by describing how control of local supersaturation by highly localized ultrasound was successfully applied to induce nucleation and to control polymorphism in reactive crystallization of L-glutamic acid.