Influence of Heat Treatment on Strength Properties of Finger-jointed Components

The purpose for the thesis was to study the thermo treatment of finger-jointed wood. The thesis concentrated on examining the tensile and bending strength of finger-jointed and thermo treated wood. The aim was to find out how different treatment temperature levels and adhesives influence the strength of wood that has been finger-jointed before heat treatment. Secondary objectives were to examine the influence of the treatment time at one temperature, determine differences in the strength between the joints in heartwood and sapwood, examine the visual appearance of the finger joints after the treatment and establish possibilities to reach a characteristic strength level corresponding to C14. Only minor differences in strength properties were measured between the finger-jointed wood treatments II and III. A greater difference was shown between these two treatment temperatures I, which lead to reduced strength. The average strength of joints glued with adhesive 2 was higher after treatments II and III compared to those glued with the adhesive 1. At the treatment temperature I, the adhesive 1 strength properties were at the same level compared to the adhesive 2 or better. There were not any significant differences.

Sormijatketun rakennesahatavaran lujuuteen vaikuttavat tekijät puun jatkojalostuksessa

Diplomityö tehtiin Stora Enson Kiteen sahalla, tuotantokäytössä olevaa sormijatkoslinjaa tutkien. Tutkimuksen tavoitteena oli selvittää raaka-aineen keskikosteuden, kosteusgradientin, mitallistamishöyläyksen ja liitettävien aihioiden pituuden vaikutus jatketun tuotteen laatuun. Koekappaleita valmistettiin viisi höylättyä ja viisi sahapintaista luokkaa. Luokat valmistettiin eripituisista aihioista, puolen metrin jaolla. Koekappaleiden taivutuslujuus mitattiin nelipistetaivutuksella, standardin EN 408 mukaan. Taivutuskokeen jälkeen kappaleista mitattiin keskikosteus ja sahattiin koepalat kosteusgradientin mittaamiseksi. Koekappaleita valmistettiin yhteensä 37.8 m3. Tutkimuksissa selvisi, että kappaleiden keskikosteuden ja taivutuslujuuden välillä vallitsee heikko positiivinen riippuvuus. Kosteusgradientin ja taivutuslujuuden välillä riippuvuus on selkeämpi, kosteusgradientin kasvaessa myös taivutuslujuus lisääntyy. Tämä selittyy kappaleiden tiheyden vaihtelulla. Tiheämpiin kappaleisiin jää kuivauksessa suurempi kosteusgradientti. Aihioiden mitallistaminen pienentää taivutuslujuuden hajontaa ja vähentää raaka-aineen mittaheittojen aiheuttamia häiriöitä tuotannossa. Aihionpituus vaikuttaa murtumatyyppien jakaumiin ja aihioiden kierouteen. Sopivin aihionpituus on tässä tapauksessa 0.8-1.0 m. Puolet kappaleista murtui liitoksen ulkopuolelta, useimmiten oksan kohdalta. Paras tapa parantaa kappaleiden lujuutta on lujuuslajitella raaka-aine.

On-line –jatkojalostuksen integrointi mäntysahan tuotantoprosessiin

Diplomityön tavoitteena oli selvittää erilaisia jatkojalostusmahdollisuuksia, joilla voidaan nostaa suuren mäntysahan tuotteiston arvoa. Lisäksi tuli tarkastella jalostuksen integrointia sahan tuotantoprosessiin. Työn taustalla on toisaalta puutuotemarkkinoiden muuttuminen ja toisaalta raaka-aineen laadullinen huononeminen. Molemmat seikat vaikuttavat negatiivisesti perinteisen mäntysahan kannattavuuteen .Jatkojalostuksen integroinnilla sahatavaraprosessiin saavutetaan säästöjä tuotantokustannuksissa, kun tarkastellaan koko prosessia tukista jatkojalosteeksi. Myös raaka-aineen tuottavuutta voidaan nostaa integraation avulla. Jatkojalostus voidaan integroida sahatavaraprosessiin raaka-aineen valikoinnilla sahatavaraprosessin eri osissa, on-line –jalostuksella sekä taloudellisesti. Sahatavaraprosessissa tapahtuva raaka-aineen valikointi voidaan suorittaa tukeista ja sahatavarasta. Valikointikriteerinä voi olla puun ominaisuudet, sahatavaran mitat ja laatu. Valikointiin voidaan nykyteknologiasta hyödyntää röntgentekniikkaa sekä konenäköä. On-line –jalostus tarkoittaa kiinteästi sahatavaraprosessiin liittyvää jalostusta, jolloin ns. turhia prosessivaiheita jää pois ja syntyy säästöjä. On-line –jalostuksen edellytys on raaka-aineen jonkin asteinen valikointi, esim. pituus. Taloudellisesti integroitu jalostus tarkoittaa, että jalostuslaitoksella pyritään nollatulokseen ja jalostuksen lisäarvo palautetaan sahan toimittamaan raaka-aineen hintaan. Tällainen toiminta yhtiön sisällä poistaa turhaa keskustelua raaka-aineen siirtohinnoista ja siten vapauttaa osaltaan resursseja tuottavampaan toimintaan. Erilaisten jatkojalostusmuotojen ja puun ominaisuuksien hyödyntämisen seulonnan perusteella löytyi yksi jalostusmuoto, jolla voidaan kohottaa mäntysahan tuotteiston arvoa. Työn tuloksena syntyi investointiehdotus aihiotankotuotannosta ikkunateollisuuden tarpeisiin. Raaka-aineen hyödynnettäviä ominaisuuksia ovat männyn sydänpuun luonnollinen kestävyys sekä keskimääräinen oksaväli. Valikointi tehdään välitukeista, joiden sahaamisen kannattavuus on männyn rungon osista heikoin. Aihiotankoprosessissa hyödynnetään konenäköä ja sormijatkostekniikkaa. Jatkojalostuksen integrointi sahatavaraprosessiin toteutetaan rakentamalla on-line –jalostuslaitos sekä soveltamalla röntgentekniikkaa raaka-aineen valinnassa.

Paikalliset elinkeinot ja ilmastonmuutos Kaakkois-Suomen alueella

Kasvihuonekaasujen vähentäminen on lähitulevaisuudessa välttämätöntä ilmastonmuutoksen torjunnassa. Tämä tosiasia tulisi nähdä niin yrityksissä kuin kunnissakin mahdollisuutena, johon liittyvillä toimenpiteillä voitaisiin kehittää myös alueen liiketoimintaa ja elinkeinoelämää. Tämän tutkimuksen tavoitteena oli löytää Kaakkois- Suomen kannalta tehokkaimmat keinot ja toimintamallit alueen liiketoiminnan edistämiseksi kasvihuonekaasupäästöjä hillitsevään suuntaan. Työssä on käsitelty erityisesti kunnan toimintaan liittyviä vaikutusmahdollisuuksia tavoitteiden saavuttamisessa. Tutkimus on toteutettu osana Suomen Kuntaliitto Ry:n koordinoimaa kuntienilmastonsuojelukampanjaa. Tutkimus on luonteeltaan kirjallisuuden pohjalta tehty esiselvitys. Työhön sisältyvien esimerkkitapausten osalta on tietoa hankittu myös haastattelemalla alueen yrityksiä. Tutkimuksen alkuvaiheessa on kartoitettu Kaakkois-Suomen alueellisia erityispiirteitä ja potentiaaleja. Työssä on arvioitu esimerkiksi uusiutuvien energialähteiden lisäämispotentiaalien käyttöönottamisella saavutettavat kasvihuonekaasupäästöjen vähenemät sekä työllisyysvaikutukset Kaakkois-Suomen alueella. Potentiaalien luoman pohjan perusteella on selvitetty mahdollisuuksia kehittää alueen elinkeinorakenteeseen soveltuvaa liiketoimintaa. Kasvihuonekaasuja vähentävän liiketoiminnan edistämiseksi on selvitetty keinoja sekä olemassa olevien yritysten kilpailukyvyn parantamiseen että uuden liiketoiminnan kehittämiseen liittyen. Näiden tavoitteiden saavuttamisessa nähtiin yritysten verkostoitumisen olevan eräs tärkeä keino, jolla voidaan parantaa mm. alueen lukuisten pienten yritysten mahdollisuuksia suurten kokonaistoimitusten tuottamisessa. Työssä on esitetty kunnan toimintaan soveltuva toimintamalli yritysten verkostoimiseksi. Jätteiden ja sivutuotteiden osalta työssä on esitetty materiaalivirtojen hyötykäyttöön ohjaamiseen erikoistunutta liiketoimintaa niin sanotun materiaalipörssin muodossa. Myös koulutuksen, tutkimuksen ja rahoituksen tarjontaa kasvihuonekaasuja vähentävän liiketoiminnan kehittämisen tueksi on selvitetty Kaakkois-Suomen alueella. Tutkimuksen sisällössä ovat esimerkkitapaukset keskeisessä asemassa. Niiden puitteissa on haastateltu paikallisen alueen yrityksiä ja viranomaisia. Esimerkkitapauksissa on selvitetty materiaalipörssin, lämpöyrittäjyyden sekä erään yrityksen verkostoimiseen liittyviä tekijöitä ja keinoja. Haastatteluista ja kirjallisuudesta saatuihin tietoihin perustuen on ehdotettu toimintavaihtoehtoja toiminnan kehittämiseksi. Tutkimuksen tulosten perusteella on lopuksi esitetty suunnitelma jatkotoimenpiteistä, joilla tuloksia lähdetään viemään käytännön tasolle.

Kaasuturbiinin polttoainesuuttimien virtausmittaus

Tässä diplomityössä suunniteltiin ja rakennettiin kaasuturbiinin kaasusuuttimien virtausmittauslaitteisto. Suuttimien epätasainen toiminta kasvattaa kaasuturbiinin poistolämpötilahajontaa. Virtausmittauksien perusteella voidaan määrittää suuttimien efektiivinen virtauspoikkipinta-ala. Suuttimien asennusjärjestys opti-moidaan suuttimien välisten pinta-alaerojen mukaisesti, jolloin polttoainevirtaus polttokammioihin on mahdollisimman tasainen ja poistolämpötilahajonta pienenee. Kaasuturbiinin MS6001 esittelyssä keskityttiin tärkeimpiin komponentteihin sekä polttoainesuuttimien testauksen kannalta oleellisiin osiin ja niiden toimintaan. Teoriaosuudessa tarkasteltiin tilavuusvirran sekä suutinvirtauksen laskennassa käytettäviä yhtälöitä. Mittalaitteiston suunnittelu ja toteutus olivat tämän työn laajin osa-alue. Laitteiston keskeiset osat ovat kuristuselin ja suutintestausosa. Kuristuselintyypiksi valittiin rengaskammiollinen kuristuslaippa, joka suun-niteltiin standardin SFS-EN ISO 5167:2003 mukaisesti. Standardissa annettujen yhtälöiden antamia tuloksia verrattiin numeerisella virtauslaskentamallilla lasket-tuihin tuloksiin. Suutinrunkojen ja -kärkien mittauksien suunnittelussa sovellettiin samaa standardia sekä numeerista virtauslaskentaa optimaalisen sijainnin löytämiseksi paineyhteelle. Mittauksissa syntyvien epävarmuuksien arviointiin kiinnitettiin erityistä huomiota. Kokeellisessa osuudessa mitattiin yhden kunnostetun suuttimen, käytetyn suut-timen ja suutinrungon virtausta. Tuloksien perusteella laskettiin efektiiviset pinta-alat, joita verrattiin turbiinivalmistajan ilmoittamiin pinta-aloihin. Lopuksi arvioitiin mittaustulosten perusteella laitteiston toimivuutta. Virhe-arvioinnin ja mittaustulosten perusteella laadittiin teknisiä parannusehdotuksia suutintestauslaitteiston luotettavan toiminnan varmistamiseksi.

Genetic regulatory networks in avian B cells

Biology is turning into an information science. The science of systems biology seeks to understand the genetic networks that govern organism development and functions. In this study the chicken was used as a model organism in the study of B cell regulatory factors. These studies open new avenues for plasma cell research by connecting the down regulation of the B cell gene expression program directly to the initiation of plasma cell differentiation. The unique advantages of the DT40 avian B cell model system, specifically its high homologous recombination rate, were utilized to study gene regulation in Pax5 knock out cell lines and to gain new insights into the B cell to plasma cell transitions that underlie the secretion of antibodies as part of the adaptive immune response. The Pax5 transcription factor is central to the commitment, development and maintenance of the B cell phenotype. Mice lacking the Pax5 gene have an arrest in development at the pro-B lymphocyte stage while DT40 cells have been derived from cells at a more mature stage of development. The DT40 Pax5-/- cells exhibited gene expression similarities with primary chicken plasma cells. The expression of the plasma cell transcription factors Blimp-1 and XBP-1 were significantly upregulated while the expression of the germinal centre factor BCL6 was diminished in Pax5-/- cells, and this alteration was normalized by Pax5 re-introduction. The Pax5-deficient cells further manifested substantially elevated secretion of IgM into the supernatant, another characteristic of plasma cells. These results for the first time indicated that the downregulation of the Pax5 gene in B cells promotes plasma cell differentiation. Cross-species meta-analysis of chicken and mouse Pax5 gene knockout studies uncovers genes and pathways whose regulatory relationship to Pax5 has remained unchanged for over 300 million years. Restriction of the hematopoietic stem cell fate to produce T, B and NK cell lineages is dependent on the Ikaros and its molecular partners, the closely related Helios and Aiolos. Ikaros family members are zinc finger proteins which act as transcriptional repressors while helping to activate lymphoid genes. Helios in mice is expressed from the hematopoietic stem cell level onwards, although later in development its expression seems to predominate in the T cell lineage. This study establishes the emergence and sequence of the chicken Ikaros family members. Helios expression in the bursa of Fabricius, germinal centres and B cell lines suggested a role for Helios in the avian B-cell lineage, too. Phylogenetic studies of the Ikaros family connect the expansion of the Ikaros family, and thus possibly the emergence of the adaptive immune system, with the second round of genome duplications originally proposed by Ohno. Paralogs that have arisen as a result of genome-wide duplications are sometimes termed ohnologs – Ikaros family proteins appear to fit that definition. This study highlighted the opportunities afforded by the genome sequencing efforts and somatic cell reverse genetics approaches using the DT40 cell line. The DT40 cell line and the avian model system promise to remain a fruitful model for mechanistic insight in the post-genomic era as well.

Verbal learning in mild cognitive impairment and alzheimer's disease : behavioural and neural approaches

The main focus of the present thesis was at verbal episodic memory processes that are particularly vulnerable to preclinical and clinical Alzheimer’s disease (AD). Here these processes were studied by a word learning paradigm, cutting across the domains of memory and language learning studies. Moreover, the differentiation between normal aging, mild cognitive impairment (MCI) and AD was studied by the cognitive screening test CERAD. In study I, the aim was to examine how patients with amnestic MCI differ from healthy controls in the different CERAD subtests. Also, the sensitivity and specificity of the CERAD screening test to MCI and AD was examined, as previous studies on the sensitivity and specificity of the CERAD have not included MCI patients. The results indicated that MCI is characterized by an encoding deficit, as shown by the overall worse performance on the CERAD Wordlist learning test compared with controls. As a screening test, CERAD was not very sensitive to MCI. In study II, verbal learning and forgetting in amnestic MCI, AD and healthy elderly controls was investigated with an experimental word learning paradigm, where names of 40 unfamiliar objects (mainly archaic tools) were trained with or without semantic support. The object names were trained during a 4-day long period and a follow-up was conducted one week, 4 weeks and 8 weeks after the training period. Manipulation of semantic support was included in the paradigm because it was hypothesized that semantic support might have some beneficial effects in the present learning task especially for the MCI group, as semantic memory is quite well preserved in MCI in contrast to episodic memory. We found that word learning was significantly impaired in MCI and AD patients, whereas forgetting patterns were similar across groups. Semantic support showed a beneficial effect on object name retrieval in the MCI group 8 weeks after training, indicating that the MCI patients’ preserved semantic memory abilities compensated for their impaired episodic memory. The MCI group performed equally well as the controls in the tasks tapping incidental learning and recognition memory, whereas the AD group showed impairment. Both the MCI and the AD group benefited less from phonological cueing than the controls. Our findings indicate that acquisition is compromised in both MCI and AD, whereas long13 term retention is not affected to the same extent. Incidental learning and recognition memory seem to be well preserved in MCI. In studies III and IV, the neural correlates of naming newly learned objects were examined in healthy elderly subjects and in amnestic MCI patients by means of positron emission tomography (PET) right after the training period. The naming of newly learned objects by healthy elderly subjects recruited a left-lateralized network, including frontotemporal regions and the cerebellum, which was more extensive than the one related to the naming of familiar objects (study III). Semantic support showed no effects on the PET results for the healthy subjects. The observed activation increases may reflect lexicalsemantic and lexical-phonological retrieval, as well as more general associative memory mechanisms. In study IV, compared to the controls, the MCI patients showed increased anterior cingulate activation when naming newly learned objects that had been learned without semantic support. This suggests a recruitment of additional executive and attentional resources in the MCI group.

Saksan kielen ja automaatiotekniikan perusteiden oppimisen yhteensovittaminen : Brückenschlag zwischen Automatisierung und Deutsch als Fremdsprache

Artikkelin kieli: finger

Training executive functions in the laboratory and in real life : cognitive consequences of computer-based exercises and bilingualism

The question of the trainability of executive functions and the impact of such training on related cognitive skills has stirred considerable research interest. Despite a number of studies investigating this, the question has not yet been solved. The general aim of this thesis was to investigate two very different types of training of executive functions: laboratory-based computerized training (Studies I-III) and realworld training through bilingualism (Studies IV-V). Bilingualism as a kind of training of executive functions is based on the idea that managing two languages requires executive resources, and previous studies have suggested a bilingual advantage in executive functions. Three executive functions were studied in the present thesis: updating of working memory (WM) contents, inhibition of irrelevant information, and shifting between tasks and mental sets. Studies I-III investigated the effects of computer-based training of WM updating (Study I), inhibition (Study II), and set shifting (Study III) in healthy young adults. All studies showed increased performance on the trained task. More importantly, improvement on an untrained task tapping the trained executive function (near transfer) was seen in Study I and II. None of the three studies showed improvement on untrained tasks tapping some other cognitive function (far transfer) as a result of training. Study I also used PET to investigate the effects of WM updating training on a neurotransmitter closely linked to WM, namely dopamine. The PET results revealed increased striatal dopamine release during WM updating performance as a result of training. Study IV investigated the ability to inhibit task-irrelevant stimuli in bilinguals and monolinguals by using a dichotic listening task. The results showed that the bilinguals exceeded the monolinguals in inhibiting task-irrelevant information. Study V introduced a new, complementary research approach to study the bilingual executive advantage and its underlying mechanisms. To circumvent the methodological problems related to natural groups design, this approach focuses only on bilinguals and examines whether individual differences in bilingual behavior correlate with executive task performances. Using measures that tap the three above-entioned executive functions, the results suggested that more frequent language switching was associated with better set shifting skills, and earlier acquisition of the second language was related to better inhibition skills. In conclusion, the present behavioral results showed that computer-based training of executive functions can improve performance on the trained task and on closely related tasks, but does not yield a more general improvement of cognitive skills. Moreover, the functional neuroimaging results reveal that WM training modulates striatal dopaminergic function, speaking for training-induced neural plasticity in this important neurotransmitter system. With regard to bilingualism, the results provide further support to the idea that bilingualism can enhance executive functions. In addition, the new complementary research approach proposed here provides some clues as to which aspects of everyday bilingual behavior may be related to the advantage in executive functions in bilingual individuals.

Integrins on the move

Cancer is a leading cause of death worldwide accounting for 13% of all deaths in 2005. The spread of cancer and formation of metastases is the major cause of mortality among cancer patients. The spread of cancer is based on the cancer cell’s ability to break away from the surrounding tissue and to migrate into new areas in the body. The ability of cells to bind its surroundings and to move is controlled by the mechanical cell surface adhesion receptors called the integrins. Integrins have a critical role in cell adhesion, cell motility and tissue homeostasis. By communicating with ECM, integrins transmit signals from the surrounding environment inside the cell and modulate the function of many important signalling pathways involved in cell survival, development, gene expression, proliferation, motility and cytoskeletal organization. During cell migration integrin-matrix adhesions are formed in front of the cell while rear-adhesions are released during migration. Integrins are endocytosed from the plasma-membrane into the cytoplasm and partly recycled back to new adhesion sites in a process called integrin trafficking. Also, the cell cytoskeleton and protrusions are important in cell migration. Finger-like actin protrusions called filopodia display an interesting cancer relevant cooperation with integrins that is required for cell migration. The expression and function of integrins changes markedly as cells acquire carcinogenic properties. Changed integrin function is partly responsible for detachment of tumor cells from neighbouring cells and for providing enhanced invasive capabilities for tumor cells to disseminate. Similarly, the formation of filopodia is increased in cancer. High myosin-10 expression is related to poor outcome in breast cancer and increased cell migration. The proper function of myosin-10 induced filopodia needs association with β1 integrins. The importance of integrin trafficking and filopodia formation is becoming increasingly more recognized in cancer. This thesis focusses on the role of integrins, integrin trafficking and myosin-10 induced filopodia cancer cell migration.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Model-based estimation of liquid flows in the blast furnace hearth and taphole

This thesis presents a set of methods and models for estimation of iron and slag flows in the blast furnace hearth and taphole. The main focus was put on predicting taphole flow patterns and estimating the effects of various taphole conditions on the drainage behavior of the blast furnace hearth. All models were based on a general understanding of the typical tap cycle of an industrial blast furnace. Some of the models were evaluated on short-term process data from the reference furnace. A computational fluid dynamics (CFD) model was built and applied to simulate the complicated hearth flows and thus to predict the regions of the hearth exerted to erosion under various operating conditions. Key boundary variables of the CFD model were provided by a simplified drainage model based on the first principles. By examining the evolutions of liquid outflow rates measured from the furnace studied, the drainage model was improved to include the effects of taphole diameter and length. The estimated slag delays showed good agreement with the observed ones. The liquid flows in the taphole were further studied using two different models and the results of both models indicated that it is more likely that separated flow of iron and slag occurs in the taphole when the liquid outflow rates are comparable during tapping. The drainage process was simulated with an integrated model based on an overall balance analysis: The high in-furnace overpressure can compensate for the resistances induced by the liquid flows in the hearth and through the taphole. Finally, a recently developed multiphase CFD model including interfacial forces between immiscible liquids was developed and both the actual iron-slag system and a water-oil system in laboratory scale were simulated. The model was demonstrated to be a useful tool for simulating hearth flows for gaining understanding of the complex phenomena in the drainage of the blast furnace.

It’s a workflow engine. It’s working with linked data. It’s repository! – Supporting electronic thesis related processes in University of Helsinki library

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Post-processing and analysis of tracked hand trajectories

In this thesis, the suitability of different trackers for finger tracking in high-speed videos was studied. Tracked finger trajectories from the videos were post-processed and analysed using various filtering and smoothing methods. Position derivatives of the trajectories, speed and acceleration were extracted for the purposes of hand motion analysis. Overall, two methods, Kernelized Correlation Filters and Spatio-Temporal Context Learning tracking, performed better than the others in the tests. Both achieved high accuracy for the selected high-speed videos and also allowed real-time processing, being able to process over 500 frames per second. In addition, the results showed that different filtering methods can be applied to produce more appropriate velocity and acceleration curves calculated from the tracking data. Local Regression filtering and Unscented Kalman Smoother gave the best results in the tests. Furthermore, the results show that tracking and filtering methods are suitable for high-speed hand-tracking and trajectory-data post-processing.

Höyryturbiinin ulosvirtauskanaviston kokeellinen tutkimus pienoismallilla

Diplomityössä tutkittiin höyryturbiinin ulosvirtauskanavistojen kokeellisia tutkimusmenetelmiä ja suoritettiin käytännön mittauksia Fortum Oyj:n Loviisan ydinvoimalaitoksen höyryturbiinien huuvan pienoismallilla. Kirjallisuusselvityksen perusteella todettiin, että pienoismallitutkimuksella on ollut keskeinen asema ulosvirtauskanavistojen suunnittelussa. Kokeellisten menetelmien perusongelmana on höyryturbiinin ulosvirtausolosuhteiden jäljitteleminen. Käytetyt mittausmenetelmät perustuvat pääosin tavanomaisiin paine- ja nopeusmittauksiin. Lisäainepartikkeleihin ja laser-valaisuun perustuva PIV (particle image velocimetry) todettiin lupaavaksi menetelmäksi ulosvirtauskanavistojen tutkimuksen saralla. Työn käytännön osuudessa tehtiin mittauksia mittasuhteessa 1:8 rakennetulle höyryturbiinin huuvan pienoismallille. Mittauksilla tutkittiin virtausta mallin sisääntulo- ja ulostulotasoissa. Lisäksi mitattiin staattisen paineen jakauma huuvan sisällä. Kokonaispainetta mittaava kiel-putki todettiin käytännölliseksi työkaluksi huuvan virtauskentän tutkimuksessa. Tuloksista käy hyvin ilmi huuvan ulostuloon syntyvien pyörteiden muodostuminen ja ulostulon epätasainen nopeusjakauma. Staattinen paine huuvan sisällä havaittiin epätasaisesti jakautuneeksi. Ulostulotason ja staattisen paineen mittauksilla saadut tulokset sopivat hyvin yhteen kirjallisuudesta löytyvien tutkimustulosten kanssa ja tukevat Loviisan ulosvirtauskanavistosta aiemmin tehtyjä CFD-simulointeja.