Experimental and Numerical Analysis of Different Volutes in a Centrifugal Compressor

In a centrifugal compressor the flow around the diffuser is collected and led to the pipe system by a spiral-shaped volute. In this study a single-stage centrifugal compressor with three different volutes is investigated. The compressorwas first equipped with the original volute, the cross-section of which was a combination of a rectangle and semi-circle. Next a new volute with a fully circular cross-section was designed and manufactured. Finally, the circular volute wasmodified by rounding the tongue and smoothing the tongue area. The overall performance of the compressor as well as the static pressure distribution after the impeller and on the volute surface were measured. The flow entering the volute was measured using a three-hole Cobra-probe, and flow visualisations were carriedout in the exit cone of the volute. In addition, the radial force acting on theimpeller was measured using magnetic bearings. The complete compressor with thecircular volute (inlet pipe, full impeller, diffuser, volute and outlet pipe) was also modelled using computational fluid dynamics (CFD). A fully 3-D viscous flow was solved using a Navier-Stokes solver, Finflo, developed at Helsinki University of Technology. Chien's k-e model was used to take account of the turbulence. The differences observed in the performance of the different volutes were quite small. The biggest differences were at low speeds and high volume flows,i.e. when the flow entered the volute most radially. In this operating regime the efficiency of the compressor with the modified circular volute was about two percentage points higher than with the other volutes. Also, according to the Cobra-probe measurements and flow visualisations, the modified circular volute performed better than the other volutes in this operating area. The circumferential static pressure distribution in the volute showed increases at low flow, constant distribution at the design flow and decrease at high flow. The non-uniform static pressure distribution of the volute was transmitted backwards across the vaneless diffuser and observed at the impeller exit. At low volume flow a strong two-wave pattern developed into the static pressure distribution at the impeller exit due to the response of the impeller to the non-uniformity of pressure. The radial force of the impeller was the greatest at the choke limit, the smallest atthe design flow, and moderate at low flow. At low flow the force increase was quite mild, whereas the increase at high flow was rapid. Thus, the non-uniformityof pressure and the force related to it are strong especially at high flow. Theforce caused by the modified circular volute was weaker at choke and more symmetric as a function of the volume flow than the force caused by the other volutes.

An experimental and theoretical study of multiphase flow in a circulating fluidized bed

A systematic averaging procedure has been derived in order to obtain an integral form of conservation equations for dispersed multiphase flow, especially applicable to fluidized beds. A similar averaging method is applied further to formulate macroscopic integral equations, which can be used in one-dimensional and macroscopic multi dimensional models. Circulating fluid bed hydrodynamics has been studied experimentally and both macroscopic and microscopic flow profiles have been measured in a cold model. As an application of the theory, the one dimensional model has been used to study mass and momentum conservation of gas and solid in a circulating fluid bed. Axial solid mixing has also been modelled by the one dimensional model and mixing parameters have been evaluated.

Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.

A study of combustion phenomena in circulating fluidized beds by developing and applying experimental and modelling methods for laboratory-scale reactors

The results shown in this thesis are based on selected publications of the 2000s decade. The work was carried out in several national and EC funded public research projects and in close cooperation with industrial partners. The main objective of the thesis was to study and quantify the most important phenomena of circulating fluidized bed combustors by developing and applying proper experimental and modelling methods using laboratory scale equipments. An understanding of the phenomena plays an essential role in the development of combustion and emission performance, and the availability and controls of CFB boilers. Experimental procedures to study fuel combustion behaviour under CFB conditions are presented in the thesis. Steady state and dynamic measurements under well controlled conditions were carried out to produce the data needed for the development of high efficiency, utility scale CFB technology. The importance of combustion control and furnace dynamics is emphasized when CFB boilers are scaled up with a once through steam cycle. Qualitative information on fuel combustion characteristics was obtained directly by comparing flue gas oxygen responses during the impulse change experiments with fuel feed. A one-dimensional, time dependent model was developed to analyse the measurement data Emission formation was studied combined with fuel combustion behaviour. Correlations were developed for NO, N2O, CO and char loading, as a function of temperature and oxygen concentration in the bed area. An online method to characterize char loading under CFB conditions was developed and validated with the pilot scale CFB tests. Finally, a new method to control air and fuel feeds in CFB combustion was introduced. The method is based on models and an analysis of the fluctuation of the flue gas oxygen concentration. The effect of high oxygen concentrations on fuel combustion behaviour was also studied to evaluate the potential of CFB boilers to apply oxygenfiring technology to CCS. In future studies, it will be necessary to go through the whole scale up chain from laboratory phenomena devices through pilot scale test rigs to large scale, commercial boilers in order to validate the applicability and scalability of the, results. This thesis shows the chain between the laboratory scale phenomena test rig (bench scale) and the CFB process test rig (pilot). CFB technology has been scaled up successfully from an industrial scale to a utility scale during the last decade. The work shown in the thesis, for its part, has supported the development by producing new detailed information on combustion under CFB conditions.

Experimental and discrete element simulation studies of bell-less charging of blast furnace

This thesis presents an experimental study and numerical study, based on the discrete element method (DEM), of bell-less charging in the blast furnace. The numerical models are based on the microscopic interaction between the particles in the blast furnace charging process. The emphasis is put on model validation, investigating several phenomena in the charging process, and on finding factors that influence the results. The study considers and simulates size segregation in the hopper discharging process, particle flow and behavior on the chute, which is the key equipment in the charging system, using mono-size spherical particles, multi-size spheres and nonspherical particles. The behavior of the particles at the burden surface and pellet percolation into a coke layer is also studied. Small-scale experiments are used to validate the DEM models.

Benzodiazepines and Cognitive Functioning in Older Adults. With Emphasis on Long-Term Use and Withdrawal

Benzodiazepines (BZD) and benzodiazepine related drugs (RD) are the most commonly used psychotropics among the aged. The use of other psychotropics taken concomitantly with BZD/ RD or their cognitive effects with BZD/RD have not been studied frequently. The aim of this academic thesis was to describe and analyse relationships between the use of BZD/RD alone or concomitantly with antipsychotics, antidepressants, opioids, antiepileptics, opioids and anticholinergics in the aged and their health. Especially, the relationships between long-term use of BZD/RD and cognitive decline were studied. Additionally, the effect of melatonin on BZD/RD withdrawal and the cognitive effects of BZD/RD withdrawal were studied. This study used multiple data sets: the first study (I) was based on clinical data containing aged patients (≥65 years; N=164) admitted to Pori City Hospital due to acute disease. The second data set (Studies II and III) was based on population-based data from the Lieto Study, a clinico-epidemiological longitudinal study carried out among the aged (≥65 years) in the municipality of Lieto. Follow-up data was formed by combining the cohort data collected in 1990-1991 (N=1283) and in 1998-1999 (N=1596) from those who participated in both cohorts (N=617). The third data set (Studies IV and V) was based on the Satauni Study’s data. This study was performed in the City of Pori in 2009-2010. In the RCT part of the Satauni Study, ninety-two long-term users of BZD/RD were withdrawn from their drugs using melatonin against placebo. The change of their cognitive abilities was measured during and after BZD/ RD withdrawal. BZD/RD use was related to worse cognitive and functional abilities, and their use may predict worse cognitive outcomes compared with BZD/RD non-users. Hypnotic use of BZD/RD could be withdrawn with psychosocial support in motivated participants, but melatonin did not improve the withdrawal results compared to those with placebo. Cognitive abilities in psychomotor tests did not show, or showed only modest, improvements for up to six months after BZD/RD withdrawal. This suggests that the cognitive effects of BZD/RD may be longlasting or permanent.

PET and MR imaging in Parkinson’s disease patients with cognitive impairment. A study of dopaminergic dysfunction, amyloid deposition, cortical hypometabolism and brain atrophy

Parkinson’s disease (PD) is the second most common neurodegenerative disorder. It is characterized by a severe loss of substantia nigra dopaminergic neurons leading to dopamine depletion in the striatum. PD affects movement, producing motor symptoms such as rigidity, tremor and bradykinesia. Non-motor symptoms include autonomic dysfunction, neurobehavioral problems and cognitive impairment, which may lead to dementia. The pathophysiological basis of cognitive impairment and dementia in PD is unclear. The aim of this thesis was to study the pathophysiological basis of cognitive impairment and dementia in PD. We evaluated the relation between frontostriatal dopaminergic dysfunction and the cognitive symptoms in PD patients with [18F]Fdopa PET. We also combined [C]PIB and [¹⁸F]FDG PET and magnetic resonance imaging in PD patients with and without dementia. In addition, we analysed subregional striatal [¹⁸F]Fdopa PET data to find out whether a simple ratio approach would reliably separate PD patients from healthy controls. The impaired dopaminergic function of the frontostriatal regions was related to the impairment in cognitive functions, such as memory and cognitive processing in PD patients. PD patients with dementia showed an impaired glucose metabolism but not amyloid deposition in the cortical brain regions, and the hypometabolism was associated with the degree of cognitive impairment. PD patients had atrophy, both in the prefrontal cortex and in the hippocampus, and the hippocampal atrophy was related to impaired memory. A single 15-min scan 75 min after a tracer injection seemed to be sufficient for separating patients with PD from healthy controls in a clinical research environment. In conclusion, the occurrence of cognitive impairment and dementia in PD seems to be multifactorial and relates to changes, such as reduced dopaminergic activity, hypometabolism, brain atrophy and rarely to amyloid accumulation.

Genetically Determined Hypometabolism in Alzheimer’s Disease and Midlife Risk Factors for Cognitive Impairment

The role of genetic factors in the pathogenesis of Alzheimer’s disease (AD) is not completely understood. In order to improve this understanding, the cerebral glucose metabolism of seven monozygotic and nine dizygotic twin pairs discordant for AD was compared to that of 13 unrelated controls using positron emission tomography (PET). Traditional region of interest analysis revealed no differences between the non-demented dizygotic co-twins and controls. In contrast, in voxel-level and automated region of interest analyses, the non-demented monozygotic co-twins displayed a lower metabolic rate in temporal and parietal cortices as well as in subcortical grey matter structures when compared to controls. Again, no reductions were seen in the non-demented dizygotic co-twins. The reductions seen in the non-demented monozygotic co-twins may indicate a higher genetically mediated risk of AD or genetically mediated hypometabolism possibly rendering them more vulnerable to AD pathogenesis. With no disease modifying treatment available for AD, prevention of dementia is of the utmost importance. A total of 2 165 at least 65 years old twins of the Finnish Twin Cohort with questionnaire data from 1981 participated in a validated telephone interview assessing cognitive function between 1999 and 2007. Those subjects reporting heavy alcohol drinking in 1981 had an elevated cognitive impairment risk over 20 years later compared to light drinkers. In addition, binge drinking was associated with an increased risk even when total alcohol consumption was controlled for, suggesting that binge drinking is an independent risk factor for cognitive impairment. When compared to light drinkers, also non-drinkers had an increased risk of cognitive impairment. Midlife hypertension, obesity and low leisure time physical activity but not hypercholesterolemia were significant risk factors for cognitive impairment. The accumulation of risk factors increased cognitive impairment risk in an additive manner. A previously postulated dementia risk score based on midlife demographic and cardiovascular factors was validated. The risk score was found to well predict cognitive impairment risk, and cognitive impairment risk increased significantly as the score became higher. However, the risk score is not accurate enough for use in the clinic without further testing.

Alterations in The States and Contents of Consciousness: Empirical and Theoretical Aspects

The main purpose of the present doctoral thesis is to investigate subjective experiences and cognitive processes in four different types of altered states of consciousness: naturally occurring dreaming, cognitively induced hypnosis, pharmacologically induced sedation, and pathological psychosis. Both empirical and theoretical research is carried out, resulting in four empirical and four theoretical studies. The thesis begins with a review of the main concepts used in consciousness research, the most influential philosophical and neurobiological theories of subjective experience, the classification of altered states of consciousness, and the main empirical methods used to study consciousness alterations. Next, findings of the original studies are discussed, as follows. Phenomenal consciousness is found to be dissociable from responsiveness, as subjective experiences do occur in unresponsive states, including anaesthetic-induced sedation and natural sleep, as demonstrated by post-awakening subjective reports. Two new tools for the content analysis of subjective experiences and dreams are presented, focusing on the diversity, complexity and dynamics of phenomenal consciousness. In addition, a new experimental paradigm of serial awakenings from non-rapid eye movement sleep is introduced, which enables more rapid sampling of dream reports than has been available in previous studies. It is also suggested that lucid dreaming can be studied using transcranial brain stimulation techniques and systematic analysis of pre-lucid dreaming. For blind judges, dreams of psychotic patients appear to be indistinguishable from waking mentation reports collected from the same patients, which indicates a close resemblance of these states of mind. However, despite phenomenological similarities, dreaming should not be treated as a uniform research model of psychotic or intact consciousness. Contrary to this, there seems to be a multiplicity of routes of how different states of consciousness can be associated. For instance, seemingly identical time perception distortions in different alterations of consciousness may have diverse underlying causes for these distortions. It is also shown that altered states do not necessarily exhibit impaired cognitive processing compared to a baseline waking state of consciousness: a case study of time perception in a hypnotic virtuoso indicates a more consistent perceptual timing under hypnosis than in a waking state. The thesis ends with a brief discussion of the most promising new perspectives for the study of alterations of consciousness.

Collectiveness within startup teams – Leading the way to initiating and managing collective pursuit of opportunities in organizational contexts

While traditional entrepreneurship literature addresses the pursuit of entrepreneurial opportunities to a solo entrepreneur, scholars increasingly agree that new ventures are often founded and operated by entrepreneurial teams as collective efforts especially in hightechnology industries. Researchers also suggest that team ventures are more likely to survive and succeed than ventures founded by the individual entrepreneur although specific challenges might relate to multiple individuals being involved in joint entrepreneurial action. In addition to new ventures, entrepreneurial teams are seen central for organizing work in established organizations since the teams are able to create major product and service innovations that drive organizational success. Acknowledgement of the entrepreneurial teams in various organizational contexts has challenged the notion on the individual entrepreneur. However, considering that entrepreneurial teams represent a collective-level phenomenon that bases on interactions between organizational members, entrepreneurial teams may not have been studied as indepth as could be expected from the point of view of the team-level, rather than the individual or the individuals in the team. Many entrepreneurial team studies adopt the individualized view of entrepreneurship and examine the team members’ aggregate characteristics or the role of a lead entrepreneur. The previous understandings might not offer a comprehensive and indepth enough understanding of collectiveness within entrepreneurial teams and team venture performance that often relates to the team-level issues in particular. In addition, as the collective-level of entrepreneurial teams has been approached in various ways in the existing literatures, the phenomenon has been difficult to understand in research and practice. Hence, there is a need to understand entrepreneurial teams at the collective-level through a systematic and comprehensive perspective. This study takes part in the discussions on entrepreneurial teams. The overall objective of this study is to offer a description and understanding of collectiveness within entrepreneurial teams beyond individual(s). The research questions of the study are: 1) what collectiveness within entrepreneurial teams stands for, what constitutes the basic elements of it, and who are included in it, 2) why, how, and when collectiveness emerges or reinforces within entrepreneurial teams, and 3) why collectiveness within entrepreneurial teams matters and how it could be developed or supported. In order to answer the above questions, this study bases on three approaches, two set of empirical data, two analysis techniques, and conceptual study. The first data set consists of 12 qualitative semi-structured interviews with business school students who are seen as prospective entrepreneurs. The data is approached through a social constructionist perspective and analyzed through discourse analysis. The second data set bases on a qualitative multiplecase study approach that aims at theory elaboration. The main data consists of 14 individual and four group semi-structured thematic interviews with members of core entrepreneurial teams of four team startups in high-technology industries. The secondary data includes publicly available documents. This data set is approached through a critical realist perspective and analyzed through systematic thematic analysis. The study is completed through a conceptual study that aims at building a theoretical model of collective-level entrepreneurship drawing from existing literatures on organizational theory and social-psychology. The theoretical work applies a positivist perspective. This study consists of two parts. The first part includes an overview that introduces the research background, knowledge gaps and objectives, research strategy, and key concepts. It also outlines the existing knowledge of entrepreneurial team literature, presents and justifies the choices of paradigms and methods, summarizes the publications, and synthesizes the findings through answering the above mentioned research questions. The second part consists of five publications that address independent research questions but all enable to answer the research questions set for this study as a whole. The findings of this study suggest a map of relevant concepts and their relationships that help grasp collectiveness within entrepreneurial teams. The analyses conducted in the publications suggest that collectiveness within entrepreneurial teams stands for cognitive and affective structures in-between team members including elements of collective entity, collective idea of business, collective effort, collective attitudes and motivations, and collective feelings. Collectiveness within entrepreneurial teams also stands for specific joint entrepreneurial action components in which the structures are constructed. The action components reflect equality and democracy, and open and direct communication in particular. Collectiveness emerges because it is a powerful tool for overcoming individualized barriers to entrepreneurship and due to collectively oriented desire for, collective value orientation to, demand for, and encouragement to team entrepreneurship. Collectiveness emerges and reinforces in processes of joint creation and realization of entrepreneurial opportunities including joint analysis and planning of the opportunities and strategies, decision-making and realization of the opportunities, and evaluation, feedback, and sanctions of entrepreneurial action. Collectiveness matters because it is relevant for potential future entrepreneurs and because it affects the ways collective ventures are initiated and managed. Collectiveness also matters because it is a versatile, dynamic, and malleable phenomenon and the ideas of it can be applied across organizational contexts that require team work in discovering or creating and realizing new opportunities. This study further discusses how the findings add to the existing knowledge of entrepreneurial team literature and how the ideas can be applied in educational, managerial, and policy contexts.