Lectio praecursoria: Environmental policy evaluation concepts exemplified in the context of the European Unions strategy for better regulation

Lectio praecursoria 3.2.2006 Tampereen yliopisto

Sustainable Waste-to-Energy Production: Performance Evaluation of Distributed Generation fuelled by Landfill Gas

The environmental impact of landfill is a growing concern in waste management practices. Thus, assessing the effectiveness of the solutions implemented to alter the issue is of importance. The objectives of the study were to provide an insight of landfill advantages, and to consolidate landfill gas importance among others alternative fuels. Finally, a case study examining the performances of energy production from a land disposal at Ylivieska was carried out to ascertain the viability of waste to energy project. Both qualitative and quantitative methods were applied. The study was conducted in two parts; the first was the review of literatures focused on landfill gas developments. Specific considerations were the conception of mechanism governing the variability of gas production and the investigation of mathematical models often used in landfill gas modeling. Furthermore, the analysis of two main distributed generation technologies used to generate energy from landfill was carried out. The review of literature revealed a high influence of waste segregation and high level of moisture content for waste stabilization process. It was found that the enhancement in accuracy for forecasting gas rate generation can be done with both mathematical modeling and field test measurements. The result of the case study mainly indicated the close dependence of the power output with the landfill gas quality and the fuel inlet pressure.

Deinking sludge utilization possibilities: technical, economic, and environmental assessments

This report introduces the ENPI project called “EMIR - Exploitation of Municipal and Industrial Residues” which was executed in a co-operation between Lappeenranta University of Technology (LUT), Saint Petersburg State University of Economics (SPbSUE), Saint Petersburg State Technical University of Plant Polymers (SPbSTUPP) and industrial partners from both Leningrad Region (LR), Russia and Finland. The main targets of the research were to identify the possibilities for deinking sludge management scenarios in co-operation with partner companies, to compare the sustainability of the alternatives, and to provide recommendations for the companies in the Leningrad Region on how to best manage deinking sludge. During the literature review, 24 deinking sludge utilization possibilities were identified, the majority falling under material recovery. Furthermore, 11 potential utilizers of deinking sludge were found within the search area determined by the transportation cost. Each potential utilizer was directly contacted in order to establish cooperation for deinking sludge utilization. Finally, four companies, namely, “Finnsementti” – a cement plant in Finland (S1), “St.Gobian Weber” – a light-weight aggregate plant in Finland (S2), “LSR-Cement” – a cement plant in LR (S3), and “Rockwool” – a stone wool plant in LR (S4) were seen as the most promising partners and were included in the economic and environmental assessments. Economic assessment using cost-benefit analysis (CBA) indicated that substitution of heavy fuel oil with dry deinking sludge in S2 was the most feasible option with a benefit/cost ratio (BCR) of 3.6 when all the sludge was utilized. At the same time, the use of 15% of the total sludge amount (the amount that could potentially be treated in the scenario) resulted in a BCR of only 0.16. The use of dry deinking sludge in the production of cement (S3) is a slightly more feasible option with a BCR of 1.1. The use of sludge in stone wool production is feasible only when all the deinking sludge is used and burned in an existing incineration plant. The least economically feasible utilization possibility is the use of sludge in cement production in Finland (S1) due to the high gate fee charged. Environmental assessment was performed applying internationally recognized life cycle assessment (LCA) methodologies: ISO 14040 and ISO 14044. The results of a consequential LCA stated that only S1 and S2 lead to a reduction of all environmental impacts within the impact categories chosen compared to the baseline scenario where deinking sludge is landfilled. Considering S1, the largest reduction of 13% was achieved for the global warming potential (GWP), whereas for S2, the largest decrease of abiotic depletion potential (ADP) was by 1.7%, the eutrophication potential (EP) by 1.8%, and a GWP of 2.1% was documented. In S3, the most notable increase of ADP and acidification potential (AP) by 2.6 and 1.5% was indicated, while the GWP was reduced by 12%, the largest out of all the impact categories. In S4, ADP and AP increased by 2.3 and 2.1% respectively, whereas ODP was reduced by 25%. During LCA, it was noticed that substitution of fuels causes a greater reduction of environmental impact (S1 and S2) than substitution of raw materials (S3 and S4). Despite a number of economically and environmentally acceptable deinking sludge utilization methods being assessed in the research, evaluation of bottlenecks and communications with companies’ representatives uncovered the fact that the availability of the raw materials consumed, and the risks associated with technological problems resulting from the sludge utilization, limited the willingness of industrial partners to start deinking sludge utilization. The research results are of high value for decision-makers at already existing paper mills since the result provide insights regarding alternatives to the deinking sludge utilization possibilities already applied. Thus, the research results support the maximum economic and environmental value recovery from waste paper utilization.

Tiehankkeiden suunnittelu - Ympäristön tilan selvitys ja ympäristövaikutusten arviointi

Tämä diplomityö on tehty ohjeeksi väyläsuunnittelijoille, tiehankkeiden suunnittelussa tehtävään ympäristön tilan selvittämiseen sekä ympäristövaikutusten arviointiin.Työn toimeksiantajana on Tieliikelaitoksen Konsultoinnin Suunnittelupalvelut. Tutkimusongelmaa lähestyttiin selvittämällä aikaisemmin suunnittelussa käytettyjätyöskentelytapoja ja -menetelmiä sekä tarkastelemalla aiemmin tehtyjä tiensuunnittelun asiakirjoja. Selvitys keskittyi Tieliikelaitoksen ja sitä edeltäneen Tielaitoksen toimintaan, mutta työssä tarkasteltiin myös muiden asiantuntijoiden laatimia suunnitelmia. Työn lähtökohtana oli laatia ohje, jonkaavulla suunnittelijat voivat tehdä suunnitelmaan kuuluvan ympäristötiedon käsittelyn itsenäisesti. Hankkeissa, joissa näin toimitaan, oletetaan ympäristövaikutusten jäävän melko vähäisiksi eikä niissä vaadita YVA-lain mukaista menettelyä. Laaditun ohjeen myötä eri suunnittelijoiden laatimat tiehankkeiden suunnitelmat yhtenäistyvät ympäristötiedon käsittelyn osalta, sillä aiemmin yhtenäistä käytäntöä ei ole ollut. Suunnitelmien laatu paranee ja ympäristövaikutusten arviointi helpottuu samaan ohjeeseen kootun tiedon avulla. Ohjeen aikaansaaman suunnittelutoiminnan kehittyminen näkyy vasta, kun ohjetta on sovellettukäytännössä hankkeiden suunnitteluun.

Metsäteollisuusintegraatin ympäristövaikutukset

Diplomityön tavoitteena oli selvittää Stora Enso Oyj Imatran tehtaiden ympäristövaikutuksia. Tarkastelu toteutettiin kahdella lähestymistavalla. Elinkaariarvioinnilla tarkasteltiin Imatran tehtaiden kartonki- ja paperituotannon elinkaaren aikaisia ympäristövaikutuksia. Elinkaariarvioinnin lisäksi tarkasteltiin Imatran tehtaiden aiheuttamia paikallisia ympäristövaikutuksia. Paikallisten vaikutusten arviointi perustui ensisijaisesti toiminnasta aiheutuvien päästöjen ja lainsäädännöllisesti ympäristön tilalle asetettujen vaatimusten ja tavoitetasojen vertailuun. Lisäksi työssä tehtiin arvio Imatran tehtaiden typenoksidipäästöjen vähentämisestä aiheutuvista kustannuksista. Työn teoriaosiossa tarkasteltiin elinkaariarvioinnin pääperiaatteita, paikallisten ympäristövaikutusten arviointiperusteita sekä yleisellä tasolla typenoksidipäästöjen vähentämistekniikoita. Elinkaariarvioinnissa ympäristövaikutuksiltaan merkittävimmiksi elinkaarivaiheiksi osoit-tautuivat paperin ja kartongin tuotantovaihe sekä kuljetukset. Paikallisten vaikutusten arvioinnissa todettiin tehtaiden jätevesien aiheuttavan lievää rehevöitymistä lähivaikutusalueella. Terveys- ja viihtyvyysvaikutuksista melu ja haju todettiin merkittävimmiksi. Työssä tarkastellut typenoksidipäästöjen vähentämismenetelmät osoittautuivat kalliiksi ja investoinneilla saavutetut ympäristöhyödyt vähäisiksi.

Hiilidioksidipäästölaskurin kehittäminen toimistoille ja yleisötapahtumille

Diplomityössä on kehitetty websovelluksena toteutettavan ilmastolaskuripalvelun hiilidioksidipäästöjen laskentamoduulit, joiden avulla toimistot ja yleisötapahtumat voivat arvioida omasta toiminnastaan syntyviä hiilidioksidipäästöjä sähkönkulutuksen, lämmönkulutuksen, matkustamisen, kuljetusten ja paperin kulutuksen osalta. Tavoitteena oli kehittää ilmastolaskurista mahdollisimman helppokäyttöinen ja kohderyhmälle hyödyllinen websovellus. Työn kirjallisuusosiossa käsitellään toimistojen ja yleisötapahtumien ympäristövaikutuksia etenkin ilmastonmuutoksen näkökulmasta. Toimistot ja yleisötapahtumat vaikuttavat ilmastonmuutokseen pääasiassa kiinteistöjen sähkön- ja lämmönkulutuksen sekä liikenteen energiankulutuksesta syntyvien hiilidioksidipäästöjen muodossa. Rakennusten energiankulutuksen ja liikenteen yhteys kansalliseen CO2-päästötaseeseen sekä päästöjenvähennystavoitteisiin on merkittävä päästökauppadirektiivin sovellusalan ulkopuolella. Lisäksi tarkastellaan paino- ja paperituotteiden elinkaaren aikaisia ympäristövaikutuksia energiankulutuksen kannalta, sillä paperi on toimistojen ja usein myös tapahtumien merkittävin yksittäinen materiaalivirta. Ilmastolaskuriin kuuluvien hiilidioksidipäästöjen laskentamoduulien kehittämisessä pyrittiin huomioimaan mahdollisimman pitkälle käyttäjien tarpeet ja tiedonsaantimahdollisuudet. Ilmastolaskuri suunniteltiin toimistojen ja yleisötapahtumien ympäristövaikutuksia käsittelevän tutkimustiedon, ilmastolaskuriprojektissa toteutetun esimarkkinakyselyn tulosten, käyttäjähaastatteluista saadun palautteen sekä keskeisesti suunnitteluprosessissa mukana olleen asiantuntijaryhmän antamien kehitysehdotusten perusteella. Työssä on esitetty ilmastolaskurisovelluksen laadulliset kriteerit, tekninen vaatimusmäärittely sekä hiilidioksidipäästöjen laskentaosuuden toteutussuunnitelma, joka sisältää laskentamoduulien käyttöliittymämallit sekä päästölaskentaan liittyvät hiilidioksidipäästökertoimet, oletusarvot, päästölaskentakaavat ja huomautukset.

Assessment of Environmental Impacts of Power Generation

Through indisputable evidence of climate change and its link to the greenhouse gas emissions comes the necessity for change in energy production infrastructure during the coming decades. Through political conventions and restrictions energy industry is pushed toward using bigger share of renewable energy sources as energy supply. In addition to climate change, sustainable energy supply is another major issue for future development plans, but neither of these should come with unbearable price. All the power production types have environmental effects as well as strengths and weaknesses. Although each change comes with a price, right track in minimising the environmental impacts and energy supply security can be found by combining all possible low-carbon technologies and by improving energy efficiency in all sectors, for creating a new power production infrastructure of tolerable energy price and of minor environmental effects. GEMIS-Global Emission Model for Integrated Systems is a life-cycle analysis program which was used in this thesis to make indicative energy models for Finland’s future energy supply. Results indicate that the energy supply must comprise both high capacity nuclear power as well as large variation of renewable energy sources for minimization of all environmental effects and keeping energy price reasonable.

Production of Mg(OH)2 from Mg-silicate rock for CO2 mineral sequestration

Sequestration of carbon dioxide in mineral rocks, also known as CO2 Capture and Mineralization (CCM), is considered to have a huge potential in stabilizing anthropogenic CO2 emissions. One of the CCM routes is the ex situ indirect gas/sold carbonation of reactive materials, such as Mg(OH)2, produced from abundantly available Mg-silicate rocks. The gas/solid carbonation method is intensively researched at Åbo Akademi University (ÅAU ), Finland because it is energetically attractive and utilizes the exothermic chemistry of Mg(OH)2 carbonation. In this thesis, a method for producing Mg(OH)2 from Mg-silicate rocks for CCM was investigated, and the process efficiency, energy and environmental impact assessed. The Mg(OH)2 process studied here was first proposed in 2008 in a Master’s Thesis by the author. At that time the process was applied to only one Mg-silicate rock (Finnish serpentinite from the Hitura nickel mine site of Finn Nickel) and the optimum process conversions, energy and environmental performance were not known. Producing Mg(OH)2 from Mg-silicate rocks involves a two-staged process of Mg extraction and Mg(OH)2 precipitation. The first stage extracts Mg and other cations by reacting pulverized serpentinite or olivine rocks with ammonium sulfate (AS) salt at 400 - 550 oC (preferably < 450 oC). In the second stage, ammonia solution reacts with the cations (extracted from the first stage after they are leached in water) to form mainly FeOOH, high purity Mg(OH)2 and aqueous (dissolved) AS. The Mg(OH)2 process described here is closed loop in nature; gaseous ammonia and water vapour are produced from the extraction stage, recovered and used as reagent for the precipitation stage. The AS reagent is thereafter recovered after the precipitation stage. The Mg extraction stage, being the conversion-determining and the most energy-intensive step of the entire CCM process chain, received a prominent attention in this study. The extraction behavior and reactivity of different rocks types (serpentinite and olivine rocks) from different locations worldwide (Australia, Finland, Lithuania, Norway and Portugal) was tested. Also, parametric evaluation was carried out to determine the optimal reaction temperature, time and chemical reagent (AS). Effects of reactor types and configuration, mixing and scale-up possibilities were also studied. The Mg(OH)2 produced can be used to convert CO2 to thermodynamically stable and environmentally benign magnesium carbonate. Therefore, the process energy and life cycle environmental performance of the ÅAU CCM technique that first produces Mg(OH)2 and the carbonates in a pressurized fluidized bed (FB) were assessed. The life cycle energy and environmental assessment approach applied in this thesis is motivated by the fact that the CCM technology should in itself offer a solution to what is both an energy and environmental problem. Results obtained in this study show that different Mg-silicate rocks react differently; olivine rocks being far less reactive than serpentinite rocks. In summary, the reactivity of Mg-silicate rocks is a function of both the chemical and physical properties of rocks. Reaction temperature and time remain important parameters to consider in process design and operation. Heat transfer properties of the reactor determine the temperature at which maximum Mg extraction is obtained. Also, an increase in reaction temperature leads to an increase in the extent of extraction, reaching a maximum yield at different temperatures depending on the reaction time. Process energy requirement for producing Mg(OH)2 from a hypothetical case of an iron-free serpentine rock is 3.62 GJ/t-CO2. This value can increase by 16 - 68% depending on the type of iron compound (FeO, Fe2O3 or Fe3O4) in the mineral. This suggests that the benefit from the potential use of FeOOH as an iron ore feedstock in iron and steelmaking should be determined by considering the energy, cost and emissions associated with the FeOOH by-product. AS recovery through crystallization is the second most energy intensive unit operation after the extraction reaction. However, the choice of mechanical vapor recompression (MVR) over the “simple evaporation” crystallization method has a potential energy savings of 15.2 GJ/t-CO2 (84 % savings). Integrating the Mg(OH)2 production method and the gas/solid carbonation process could provide up to an 25% energy offset to the CCM process energy requirements. Life cycle inventory assessment (LCIA) results show that for every ton of CO2 mineralized, the ÅAU CCM process avoids 430 - 480 kg CO2. The Mg(OH)2 process studied in this thesis has many promising features. Even at the current high energy and environmental burden, producing Mg(OH)2 from Mg-silicates can play a significant role in advancing CCM processes. However, dedicated future research and development (R&D) have potential to significantly improve the Mg(OH)2 process performance.

The Environmental Status of the Port of HaminaKotka

This study is a part of the Ecologically Friendly Port Ust-Luga (EFP) project. The purpose of this study is to examine the environmental status of the Finnish ports and, more specifically, the Port of HaminaKotka. An analysis of the environmental status is performed mainly as a literature review, because the Finnish ports must comply with Finnish and EU legislation and with the binding international regulations and conventions created by different organizations. The International Maritime Organisation (IMO) has done groundbreaking work in the field of maritime safety and maritime environmental protection. The MARPOL convention has a great impact on decreasing pollution from international shipping and it applies to 99% of the world’s merchant tonnage. Pollution prevention covers: Oil pollution, Chemical pollution, Air pollution and GHG Emissions, Dumping of Wasted and Other Matters, Garbage, Sewage, Port Reception Facilities, Special Areas under MARPOL and Particularly Sensitive Sea Areas. There is also Pollution Prevention for other treaties like anti-fouling systems used on ships, the transfer of alien species by ships’ ballast water and the environmentally sound recycling of ships. There are more than twenty different EU and international regulations that influence ports and port operations in Finland. In addition, there is also national legislation that has an effect on Finnish ports. For the most part, the legislation for ports is common in the EU area, but the biggest and most important difference between the legislation in Finland and other EU countries is due to the Act on Environmental Impact Assessment Procedure. The Act states that the environmental impact assessment procedure shall be applied to projects that may have significant adverse environmental impacts, due to the special features of Finland`s nature and environment. In this Act, the term environmental impact refers to the direct and indirect effects inside and outside Finnish territory of a project or operations on human health, living conditions and amenity; soil, water, air, climate, organisms, interaction between them and biodiversity; community structure, buildings, landscape, townscape and cultural heritage; utilization of natural resources. In Finland, the Environmental Permit requires that ports collect all necessary information concerning environmental effects and make required reports to the Finnish authorities, stakeholders and the public. Commonly, environmental reporting is public and environmental achievements are emphasized in reporting and in media. At the moment, the problem in environmental reporting is that it’s difficult to compare data from different ports. There is enough data concerning the environmental effects and performance, but the manner of reporting and the quality of the data varies between ports. There are differences in the units and codes used, in some cases the information is not sufficient and it can even be rather unreliable. There are also differences regarding the subjects that are emphasized in reporting.

Sustainable Gold Mining- Life Cycle Assessment of Cyanidation and Thiosulphate Leaching

With the increasing concern of the sustainable approach of gold mining, thiosulphate has been researched as an alternative lixiviant to cyanide since cyanide is toxic to the environment. In order to investigate the possibility of thiosulphate leaching application in the coming future, life cycle assessment, is conducted to compare the environmental footprint of cyanidation and thiosulphate leaching. The result showed the most significant environmental impact of cyanidation is toxicity to human, while the ammonia of thiosulphate leaching is also a major concern of acidification. In addition, an ecosystem evaluation is also performed to indicate the potential damages caused by an example of cyanide spill at Kittilä mine, resulting in significant environmental risk cost that has to be taken into account for decision making. From the opinion collected from an online LinkedIn discussion forum, the anxiety of sustainability alone would not be enough to contribute a significant change of conventional cyanidation, until the tighten policy of cyanide use. International Cyanide Code, therefore, is crucial for safe gold production. Nevertheless, it is still thoughtful to consider the values of healthy ecosystem and the gold for long-term benefit.

Evaluating land-use related environmental impacts of biomass value chains for decision-support : Comparison and testing of methodologies proposed for environmental life cycle assessment

Life cycle assessment (LCA) is one of the most established quantitative tools for environmental impact assessment of products. To be able to provide support to environmentally-aware decision makers on environmental impacts of biomass value-chains, the scope of LCA methodology needs to be augmented to cover landuse related environmental impacts. This dissertation focuses on analysing and discussing potential impact assessment methods, conceptual models and environmental indicators that have been proposed to be implemented into the LCA framework for impacts of land use. The applicability of proposed indicators and impact assessment frameworks is tested from practitioners' perspective, especially focusing on forest biomass value chains. The impacts of land use on biodiversity, resource depletion, climate change and other ecosystem services is analysed and discussed and the interplay in between value choices in LCA modelling and the decision-making situations to be supported is critically discussed. It was found out that land use impact indicators are necessary in LCA in highlighting differences in impacts from distinct land use classes. However, many open questions remain on certainty of highlighting actual impacts of land use, especially regarding impacts of managed forest land use on biodiversity and ecosystem services such as water regulation and purification. The climate impact of energy use of boreal stemwood was found to be higher in the short term and lower in the long-term in comparison with fossil fuels that emit identical amount of CO2 in combustion, due to changes implied to forest C stocks. The climate impacts of energy use of boreal stemwood were found to be higher than the previous estimates suggest on forest residues and stumps. The product lifetime was found to have much higher influence on the climate impacts of woodbased value chains than the origin of stemwood either from thinnings or final fellings. Climate neutrality seems to be likely only in the case when almost all the carbon of harvested wood is stored in long-lived wooden products. In the current form, the land use impacts cannot be modelled with a high degree of certainty nor communicated with adequate level of clarity to decision makers. The academia needs to keep on improving the modelling framework, and more importantly, clearly communicate to decision-makers the limited certainty on whether land-use intensive activities can help in meeting the strict mitigation targets we are globally facing.

A Web-Based Environmental Toolkit to Support Small and Medium-Sized Enterprises in the Implementation of Their Own Environmental Management System

With small and medium sized-enterprises (SMEs) taking up the majority of the global businesses, it is important they act in an environmentally responsible manner. Environmental management systems (EMS) help companies evaluate and improve their environmental impact but they often require human, financial, and temporary resources that not all SMEs can provide. This research encompasses interviews with representatives of two small enterprises in Germany to provide insights into their understanding, and knowledge of an EMS and how they perceive their responsibility towards the environment. Furthermore, it presents a toolkit created especially for small and medium-sized enterprises that serves as a simplified version of an EMS based on the ISO 14001 standard and is evaluated by the representatives of the SMEs. Some of the findings are: while being open to the idea of improving their environmental impact, SMEs do not always feel it is their responsibility to do so; they seem to lack the means to fully implement an EMS. The developed toolkit is considered useful and usable and recommendations are drawn for its future enhancement.

A Belief rule-based environmental responsibility assessment system for small and medium-sized enterprises

Various environmental management systems, standards and tools are being created to assist companies to become more environmental friendly. However, not all the enterprises have adopted environmental policies in the same scale and range. Additionally, there is no existing guide to help them determine their level of environmental responsibility and subsequently, provide support to enable them to move forward towards environmental responsibility excellence. This research proposes the use of a Belief Rule-Based approach to assess an enterprise’s level commitment to environmental issues. The Environmental Responsibility BRB assessment system has been developed for this research. Participating companies will have to complete a structured questionnaire. An automated analysis of their responses (using the Belief Rule-Based approach) will determine their environmental responsibility level. This is followed by a recommendation on how to progress to the next level. The recommended best practices will help promote understanding, increase awareness, and make the organization greener. BRB systems consist of two parts: Knowledge Base and Inference Engine. The knowledge base in this research is constructed after an in-depth literature review, critical analyses of existing environmental performance assessment models and primarily guided by the EU Draft Background Report on "Best Environmental Management Practice in the Telecommunications and ICT Services Sector". The reasoning algorithm of a selected Drools JBoss BRB inference engine is forward chaining, where an inference starts iteratively searching for a pattern-match of the input and if-then clause. However, the forward chaining mechanism is not equipped with uncertainty handling. Therefore, a decision is made to deploy an evidential reasoning and forward chaining with a hybrid knowledge representation inference scheme to accommodate imprecision, ambiguity and fuzzy types of uncertainties. It is believed that such a system generates well balanced, sensible and Green ICT readiness adapted results, to help enterprises focus on making improvements on more sustainable business operations.

Embedding sustainability into the new computer science curriculum for English schools

The primary goals of this study are to: embed sustainable concepts of energy consumption into certain part of existing Computer Science curriculum for English schools; investigate how to motivate 7-to-11 years old kids to learn these concepts; promote responsive ICT (Information and Communications Technology) use by these kids in their daily life; raise their awareness of today’s ecological challenges. Sustainability-related ICT lessons developed aim to provoke computational thinking and creativity to foster understanding of environmental impact of ICT and positive environmental impact of small changes in user energy consumption behaviour. The importance of including sustainability into the Computer Science curriculum is due to the fact that ICT is both a solution and one of the causes of current world ecological problems. This research follows Agile software development methodology. In order to achieve the aforementioned goals, sustainability requirements, curriculum requirements and technical requirements are firstly analysed. Secondly, the web-based user interface is designed. In parallel, a set of three online lessons (video, slideshow and game) is created for the website GreenICTKids.com taking into account several green design patterns. Finally, the evaluation phase involves the collection of adults’ and kids’ feedback on the following: user interface; contents; user interaction; impacts on the kids’ sustainability awareness and on the kids’ behaviour with technologies. In conclusion, a list of research outcomes is as follows: 92% of the adults learnt more about energy consumption; 80% of the kids are motivated to learn about energy consumption and found the website easy to use; 100% of the kids understood the contents and liked website’s visual aspect; 100% of the kids will try to apply in their daily life what they learnt through the online lessons.