Painelaitehitsauksen laadunhallintajärjestelmän kehittäminen voimalaitosten kunnossapitotöissä

Diplomityössä tarkastellaan paineenalaisten laitteiden hitsaukseen liittyviä laadullisia asioita voimalaitosten kunnossapitotöissä. Työssä selvitetään hitsauksen laadunhallinnan on-gelmakohtia ja niiden aiheuttajia sekä tutustutaan erilaisiin toimintaa helpottaviin laadun-hallinnan työkaluihin. Teoriaosuus koostuu erilaisiin laatutyökaluihin, kuten ISO 9001- ja ISO 3834 -standardeihin, Total Welding Managementiin ja Benchmarkingiin tutustumisesta sekä hit-sauksen laatukäsitteen tarkentamisesta. Osaa näistä laadunhallinnan työkaluista käytettiin parantamaan painelaitehitsauksen laatujärjestelmää voimalaitosten kunnossapitotöissä. Laadunhallinnan kannalta korjaus- ja kunnossapitotyöt ovat haastavia, koska ne ovat todel-la monipuolisia ja lähes aina erilaisia. Hitsaustyöt ovat usein toisistaan poikkeavia, eikä valmistavaa hitsaustuotantoa suoriteta kuin harvoissa tapauksissa. Havaittuja ongelmakoh-tia olivat tiedonkulun puutteet suunnittelun ja työn toteutuksen välillä sekä painelaitteiden hitsaustöistä vaadittavien dokumenttien laadinnan ja tiedonjaon hitaus. Helsingin Energian painelaitehitsauksen laatujärjestelmän päivityksen yhteydessä huomat-tiin, että uusien tiedonjakojärjestelmien käyttöönotto helpottaa dokumenttien saatavuutta ja pienentää huomattavasti henkilöstön työtaakkaa laadittaessa painelaitteiden vaatimusten-mukaisuusvakuutuksia ja muita vaadittavia dokumentaatioita.

Effects of restricted methionine and energy intake on egg weight and shell quality

Selostus: Metioniinin ja energian saannin rajoittamisen vaikutukset kananmunan painoon ja laatuun

Improvement of pyrolysis oil quality by scrubbing

Diplomityössä tutkittiin kuuman pyrolyysihöyryn puhdistamista haisevista ja kevyistä haihtuvista yhdisteistä. Työn kirjallisuusosassa selvitettiin pyrolyysiöljyn kannattavuutta uusiutuvana energialähteenä. Lisäksi eri pesurityyppejä tarkasteltiin ja ja vertailtiin. Työn kokeellisessa osassa käytettiin kahta erilaista koelaitteistoa. Tuotteen talteenotossa vertailtiin reaktorilämpötilan ja raaka-aineen kosteuden vaikutusta pyrolyysisaantoihin. Komponenttien talteenotossa tutkittiin epästabiilien ja pistävän hajuisten yhdisteiden poistamista kuumasta pyrolyysihöyrystä. Raaka-aineena käytettiin kuusen metsätäh-dehaketta, joka sisältää runsaasti neulasia ja kaarnaa. Kokeet toteutettiin lämpötila-alueella 460 - 520 °C. Koelaitteistot koostuivat kaasun (N2) syöttöjärjestelmään kytketystä kuumasta ja kyl-mästä puolesta. Tuotteen talteenotossa kuuma pyrolyysihöyry jäähdytettiin ja otettiin talteen. Komponenttien talteenotossa tuote kerättiin suodattimelle ja metyleeniklo-ridiloukkuun. Tuotteiden koostumukset analysoitiin kaasukromatokrafilla. Korkeimmat orgaaniset saannot saatiin 480 °C reaktorilämpötilalla ja 8-9 p-% raaka-ainekosteudella. Pyrolyysiveden määrä putosi raaka-aineen kosteutta nostettaessa. Eri reaktorilämpötiloilla ja raaka-ainekosteuksilla ei ollut vaikutusta hiiltosaantoihin. Kaasusaannot (pääosin CO2, CO ja hiilivedyt) olivat noin 10 p-%. Komponenttien talteenotossa suodatin tukkeutui matalissa (< 250 °C) lämpötiloissa. Suodattimelle jäänyt materiaali oli pääosin neulasista ja kaarnasta peräisin olevia uuteaineita (pääosin hartsi- rasvahappoja) ja sokereita. Korkeimmissa lämpötiloissa (> 250 °C) uuteaineet läpäisivät suodattimen paremmin. 250 ja 300 °C:n lämpötiloissa suuri määrä lyhytketjuisia helposti haihtuvia epästabiileja ja haisevia yhdisteitä (ketoneja, furaani- ja furfuraalijohdannaisia jne.) jäi metyleenikloridi- ja metanoliloukkuihin.

Adaptive optimization schemes for mobile VoIP applications Battery life and call quality aspects

In this thesis programmatic, application-layer means for better energy-efficiency in the VoIP application domain are studied. The work presented concentrates on optimizations which are suitable for VoIP-implementations utilizing SIP and IEEE 802.11 technologies. Energy-saving optimizations can have an impact on perceived call quality, and thus energy-saving means are studied together with those factors affecting perceived call quality. In this thesis a general view on a topic is given. Based on theory, adaptive optimization schemes for dynamic controlling of application's operation are proposed. A runtime quality model, capable of being integrated into optimization schemes, is developed for VoIP call quality estimation. Based on proposed optimization schemes, some power consumption measurements are done to find out achievable advantages. Measurement results show that a reduction in power consumption is possible to achieve with the help of adaptive optimization schemes.

Lanthanide Chelates as Donors in Fluorescence Resonance Energy Transfer: Exciting Prospects for Bioaffinity Assay Detection

Fluorescence resonance energy transfer (FRET) is a non-radiative energy transfer from a fluorescent donor molecule to an appropriate acceptor molecule and a commonly used technique to develop homogeneous assays. If the emission spectrum of the donor overlaps with the excitation spectrum of the acceptor, FRET might occur. As a consequence, the emission of the donor is decreased and the emission of the acceptor (if fluorescent) increased. Furthermore, the distance between the donor and the acceptor needs to be short enough, commonly 10-100 Å. Typically, the close proximity between the donor and the acceptor is achieved via bioaffinity interactions e.g. antibody binding antigen. Large variety of donors and acceptors exist. The selection of the donor/acceptor pair should be done not only based on the requirements of FRET but also the performance expectancies and the objectives of the application should be considered. In this study, the exceptional fluorescence properties of the lanthanide chelates were employed to develop two novel homogeneous immunoassays: a non-competitive hapten (estradiol) assay based on a single binder and a dual-parametric total and free PSA assay. In addition, the quenching efficiencies and energy transfer properties of various donor/acceptor pairs were studied. The applied donors were either europium(III) or terbium(III) chelates; whereas several organic dyes (both fluorescent and quenchers) acted as acceptors. First, it was shown that if the interaction between the donor/acceptor complexes is of high quality (e.g. biotin-streptavidin) the fluorescence of the europium(III) chelate could be quenched rather efficiently. Furthermore, the quenching based homogeneous non-competitive assay for estradiol had significantly better sensitivity (~67 times) than a corresponding homogeneous competitive assay using the same assay components. Second, if the acceptors were chosen to emit at the emission minima of the terbium(III) chelate, several acceptor emissions could be measured simultaneously without significant cross-talk from other acceptors. Based on these results, the appropriate acceptors were chosen for the dual-parameter assay. The developed homogeneous dual-parameter assay was able to measure both total and free PSA simultaneously using a simple mix and measure protocol. Correlation of this assay to a heterogeneous single parameter assay was excellent (above 0.99 for both) when spiked human plasma samples were used. However, due to the interference of the sample material, the obtained concentrations were slightly lower with the homogeneous than the heterogeneous assay, especially for the free PSA. To conclude, in this work two novel immunoassay principles were developed, which both are adaptable to other analytes. However, the hapten assay requires a rather good antibody with low dissociation rate and high affinity; whereas the dual-parameter assay principle is applicable whenever two immunometric complexes can form simultaneously, provided that the requirements of FRET are fulfilled.

Marketing of Lappeenranta University of Technology energy auditing services

The objective of this study was to find out how LUT Energy should start marketing its energy audit services, what would be the optimal pricing policy for its services and how LUT Energy could manage customer expectations towards quality of its auditing services. In order to answer these questions, a quantitative survey questionnaire was sent by e-mail to 56 companies from the regions of South Karelia and Kymenlaakso. The empirical data of the study was the answers and opinions of the companies, previous researches about energy efficiency and articles and presentations about the current situation in the energy efficiency market. The results of the study were that there is a great potential for energy audit services and also the legislation requires companies to improve their energy efficiency. To start marketing its services, LUT Energy should first clarify its service concept and divide its service offering into two offers. It should also clarify the marketing message it wants to send its customers and then do the marketing with the help of three-way-model. The best pricing policy for the service would be that the price is proportioned to the future savings. In order to ensure the quality of its services, LUT Energy has to make sure that both dimensions of the quality are managed properly and to fade out customer expectations towards the quality the auditing work has to be monitored.

Sustainable Waste-to-Energy Production: Performance Evaluation of Distributed Generation fuelled by Landfill Gas

The environmental impact of landfill is a growing concern in waste management practices. Thus, assessing the effectiveness of the solutions implemented to alter the issue is of importance. The objectives of the study were to provide an insight of landfill advantages, and to consolidate landfill gas importance among others alternative fuels. Finally, a case study examining the performances of energy production from a land disposal at Ylivieska was carried out to ascertain the viability of waste to energy project. Both qualitative and quantitative methods were applied. The study was conducted in two parts; the first was the review of literatures focused on landfill gas developments. Specific considerations were the conception of mechanism governing the variability of gas production and the investigation of mathematical models often used in landfill gas modeling. Furthermore, the analysis of two main distributed generation technologies used to generate energy from landfill was carried out. The review of literature revealed a high influence of waste segregation and high level of moisture content for waste stabilization process. It was found that the enhancement in accuracy for forecasting gas rate generation can be done with both mathematical modeling and field test measurements. The result of the case study mainly indicated the close dependence of the power output with the landfill gas quality and the fuel inlet pressure.

Self-Assessement Report for International Accreditation - Bachelor's and Master's degree programmes in Energy Technology

Self-Assessment Report was made for the accreditation of degree programmes in Energy Technology. The report includes the following items: the content,concept and implementation of of the degree programmes, the resources, the quality management and further development of the degree programmes.

The energy efficiency of chilled beam systems in an office building at different climates

Besides the sustaining of healthy and comfortable indoor climate, the air conditioning system should also achieve for energy efficiency. The target indoor climate can be ob-tained with different systems; this study focuses on comparing the energy efficiency of different air conditioning room unit systems in different climates. The calculations are made with dynamic energy simulation software IDA ICE by comparing the indoor cli-mate and energy consumption of an office building with different systems in different climates. The aim of the study is to compare the energy efficiency of chilled beam systems to other common systems: variable air volume, fan coil and radiant ceiling systems. Besides the annual energy consumption also the sustainability of target indoor climate is compared between the simulations. Another aim is to provide conclusions to be used in the product development of the chilled beam systems’ energy efficiency. The adaptable chilled beam system and the radiant ceiling system prove to be energy efficient independent of the climate. The challenge of reliable comparison is that other systems are not able to reach the target indoor climate as well as the others. The complex calculation environment of the simulation software, made assumptions and excluding of the financial aspects complicate comparing the big picture. The results show that the development of the chilled beam systems should concentrate on energy efficient night heating, flexible demand based ventilation and capacity control and possibilities on integrating the best practices with other systems. 

Indoor air quality at a waste incineration plant in Finland

Waste has been incinerated for energy utilization for more than a hundred years, but the harmful emissions emitted from the incineration plants did not begin to cause concern until the 1980s. Many plants were shutdown and the waste incineration plant in Kyläsaari Helsinki was one of them. In later years, new landfill regulations have increased the interest in waste incineration. During the last year, four new plants were taken into operation in Finland, Westenergy in Vaasa among them. The presence of dust has been observed indoors at Westenergy waste incineration plant. Dust is defined as particles with a diameter above 10 μm, while fine particles have a diameter smaller than 2.5 μm, ultrafine under 0.1 μm and nanoparticles under 0.05 μm. In recent years, the focus of particle health research has been changed to investigate smaller particles. Ultrafine particles have been found to be more detrimental to health than larger particles. Limit values regulating the concentrations of ultrafine particles have not been determined yet. The objective of this thesis was to investigate dust and particles present inside the Westenergy waste incineration facility. The task was to investigate the potential pollutant sources and to give recommendations of how to minimize the presence of dust and particles in the power plant. The total particle number concentrations and size distributions where measured at 15 points inside the plant with an Engine Exhaust Particle Sizer (EEPS) Spectrometer. The measured particles were mainly in the ultrafine size range. Dust was only visually investigated, since the main purpose was to follow the dust accumulation. The measurement points inside the incineration plant were chosen according to investigate exposure to visitors and workers. At some points probable leakage of emissions were investigated. The measurements were carried out during approximately one month in March–April 2013. The results of the measurements showed that elevated levels of dust and particles are present in the indoor air at the waste incineration plant. The cleanest air was found in the control room, warehouse and office. The most polluted air was near the sources that were investigated due to possible leakage and in the bottom ash hall. However, the concentrations were near measured background concentrations in European cities and no leakage could be detected. The high concentrations were assumed to be a result of a lot of dust and particles present on surfaces that had not been cleaned in a while. The main source of the dust and particles present inside the waste incineration plant was thought to be particles and dust from the outside air. Other activities in the area around the waste incineration facility are ground work activities, stone crushing and traffic, which probably are sources of particle formation. Filtration of the outside air prior entering the facility would probably save personnel and visitors from nuisance and save in cleaning and maintenance costs.

Quality, Productivity and Economy in Welding Manufacturing - Case Study: West Africa

This thesis studies quality, productivity and economy in welding manufacturing in West African states such as Ghana, Nigeria and Cameroon. The study consists of two parts: the first part, which forms the theoretical background, reviews relevant literature concerning the metal and welding industries, and measurement of welding quality, productivity and economy. The second part, which is the empirical part, aims to identify activities in the metal manufacturing industries where welding is extensively used and to determine the extent of welding quality, productivity and economy measurements in companies operating in the metal manufacturing industries. Additionally, the thesis aims to identify challenges that companies face and to assess the feasibility of creating a network to address these issues. The research methods used in the empirical part are the case study (qualitative) method and the survey (quantitative) method. However, the case study method was used to elicit information from companies in Ghana, while the survey method was used to elicit information from companies in Nigeria and Cameroon. The study considers important areas that contribute to creating awareness and understanding of the current situation of the welding industry in West Africa. These areas include the metal manufacturing industrial sector, metal products manufactured, metal production and manufacturing systems deployed, welding quality, productivity and economy measurement systems utilized, equipment and materials on the markets, general challenges facing companies in welding operations, welding technology programs and research in local universities, and SWOT analysis of the various West African states. The notable findings indicate that majority of the companies operate in the constructionindustrial sector. Also, majority of the companies are project manufacturing oriented, thus provide services to customers operating in the growing industries such as the oil and gas, mining, food and the energy industry. In addition, only few companies are certified under standards such as ISO 9001, ISO 3834, and OHSAS 18001. More so, majority of the companies employ manual welding technique, and shielded metal arc welding (SMAW) as the commonly used welding process. Finally, welder salary is about € 300 / month as of June 2013 and the average operations turnover of medium to large companies is about € 5 million / year as at 2012. Based on analysis of the results of the study, it is noted that while welding activities are growing, the availability of cheap labor, the need for company and welder qualification and certification, and the need to manufacture innovative products through developmental projects (transfer of welding expertise and technology) remain as untapped opportunities in the welding industry in the West African states. The study serves as a solid platform for further research and concludes with several recommendations for development of the West African welding industry.

INSPIRE: contributions to Invenio from the leading High Energy Physics (HEP) platform

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Container logistic innovations in forest-energy sector: Markets, future service concepts and technical improvements

The report presents the results of the commercialization project called the Container logistic services for forest bioenergy. The project promotes new business that is emerging around overall container logistic services in the bioenergy sector. The results assess the European markets of the container logistics for biomass, enablers for new business creation and required service bundles for the concept. We also demonstrate the customer value of the container logistic services for different market segments. The concept analysis is based on concept mapping, quality function deployment process (QFD) and business network analysis. The business network analysis assesses key shareholders and their mutual connections. The performance of the roadside chipping chain is analysed by the logistic cost simulation, RFID system demonstration and freezing tests. The EU has set the renewable energy target to 20 % in 2020 of which Biomass could account for two-thirds. In the Europe, the production of wood fuels was 132.9 million solid-m3 in 2012 and production of wood chips and particles was 69.0 million solidm3. The wood-based chips and particle flows are suitable for container transportation providing market of 180.6 million loose- m3 which mean 4.5 million container loads per year. The intermodal logistics of trucks and trains are promising for the composite containers because the biomass does not freeze onto the inner surfaces in the unloading situations. The overall service concept includes several packages: container rental, container maintenance, terminal services, RFID-tracking service, and simulation and ERP-integration service. The container rental and maintenance would provide transportation entrepreneurs a way to increase the capacity without high investment costs. The RFID-concept would lead to better work planning improving profitability throughout the logistic chain and simulation supports fuel supply optimization.

Framework for Regional Heating Energy Efficiency Assessment

The aim of this project was to develop general framework for systematic assessment of energy efficiency of heating on regional level in Russia. The framework created during this project includes two main instruments, namely: general regional heating energy efficiency assessment model (REEMod) and general regional heating energy efficiency assessment criteria for housing areas (REECrit). Framework pays extreme attention to realization of energy saving, overall cost efficiency and comfortable indoor climate. Life-cycle ideology was applied during creation of the framework. Application of the framework can provide decision-making process with systematically collected and processed information on current state of areas energy efficiency. Such information will help decision makers to evaluate current situation of the whole energy chain, to compare different development scenarios and to identify the most efficient improvement methods, thus supporting realization of regions efficient energy management. Simultaneous pursuit of energy savings, cost efficiency and indoor air quality can contribute to development of sustainable community. Presented instruments should be continuously developed further as an iterative process based on knew experience, development of technology and overall understanding of energy efficiency issues.

Fundraising and investor relations in social enterprise: Marketing your way out of the pioneer gap in African off-grid renewable energy

Social enterprises apply the best of business for the pursuit of social or environmental mission while also generating revenues. Globally, nearly 1,3 billion people lack access to electricity, as well as another billion having access to only low quality and infrequent electricity. Off-grid renewable energy, like solar, will increasingly have a key role in the solution of the energy access issue. The pioneer gap in off-grid renewable energy consists of financing (or funding) gaps and capacity gaps, to do with both the early stage of the enterprises in question, as well as the early stage of the whole industry. The gaps are emphasised by specific characteristics of off-grid renewable energy business models and the requirements of operating in bottom-of-the-pyramid markets. The marketing perspective to fundraising is chosen to uncover the possible role enterprises themselves have in bridging the pioneer gap. The purpose of this thesis is to study how social enterprises operating in off-grid renewable energy in Africa utilise marketing activities in their investor relations in bridging the pioneer gap. This main research question is divided into the following sub-questions:  How does the pioneer gap affect fundraising for these enterprises?  How are the funding needs for these enterprises characterised?  How do these enterprises build trust in their investor relations? The theoretic framework is built on relationship marketing and investor relations, with an emphasis on creation of trust. The research is conducted as a thematical case study. Primary data is gathered via semi-structured interviews with six solar energy companies and two accelerators. According to the findings, the main components affecting trust-creation are diminished information asymmetry and perceived risk, mission alignment as well as a personal fit or relationship with the investor. Therefore, an enterprise can utilise e.g. the following marketing activities in their investor relations to bridge the pioneer gap: ensuring investor material, the enterprise story and presenting of them is clear, concise and complete to “package” the enterprise as an investment; taking investor needs and motivations into account as well as utilising existing investors as ambassadors.