Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Embedded Monitoring Server

This study investigates, designs, and implements an inexpensive application that allows local and remote monitoring of a home. The application consists of an array of sensors for monitoring different conditions in a home environment and also for accessing the devices that might be connected to the system. Only a few sensors are initially involved in this study and information about the temperature level, forced entry detection, smoke and water leakage detection can be obtained at any time from any location with an Internet connection. The application software (coded in C language) runs on an embedded system which is basically a wireless Linksys router running on a GNU/Linux based firmware for embedded systems. Interaction between the sensors and the application software is achieved through an implemented sensor interfacing circuit. The communication with the sensor interfacing unit is done through the serial port, and accessibility of the connected sensors is achieved through a telnet client. The sensors can be accessed from local and remote locations with the sensors giving reliable information. The resulting application shows that it is possible to use the router for other applications other than what it is intended for.

Design of an Embedded Computer Board for Networking Applications

Tämä diplomityö tehtiin Convergens Oy:lle. Convergens on elektroniikan suunnittelutoimisto, joka on erikoistunut sulautettuihin järjestelmiin sekä tietoliikennetekniikkaan. Diplomityön tavoitteena oli suunnitella tietokonekortti tietoliikennesovelluksia varten asiakkaalle, jolta vaatimusmäärittelyt tulivat. Työ on rajattu koskemaan laitteen prototyypin suunnittelua. Työssä suunnitellaan pääasiassa WLAN-tukiaseman tietokone. Tukiasema onasennettavissa toimistoihin, varastoihin, kauppoihin sekä myös liikkuvaan ajoneuvoon. Suunnittelussa on otettu nämä asiat huomioon, ja laitteen akun pystyy lataamaan muun muassa auton akulla. Langattomat tekniikat ovat voimakkaasti yleistymässä, ja tämän työn tukiasema tarjoaakin varteenotettavan vaihtoehdon lukuisilla ominaisuuksillaan. Mukana on mm. GPS, Bluetooth sekä Ethernet-valmius. Langattomien tekniikoiden lisäksi myös sulautetut järjestelmät ovat voimakkaasti yleistymässä, ja nykyään mikroprosessoreita löytääkin lähesmistä vain. Tässä projektissa käytetty prosessori on nopeutensa puolesta kilpailukykyinen, ja siitä löytyy useita eri rajapintoja. Jatkossa tietokonekortille on myös tulossa WiMAX-tuki, joka lisää tukiaseman tulevaisuuden arvoa asiakkaalle. Projektiin valittu Freescalen MPC8321E-prosessori on PowerPC-arkkitehtuuriin perustuva ja juuri markkinoille ilmestynyt. Tämä toi mukanaan lisähaasteen, sillä kyseisestä prosessorista ei ollut vielä kaikkea tietoa saatavilla. Mekaniikka toi omat haasteensa mukanaan, sillä se rajoitti piirilevyn koonniin, että ylimääräistä piirilevytilaa ei juurikaan jäänyt. Tämän takia esimerkiksi DDR-muistit olivat haastavia reitittää, sillä muistivetojen on oltava melko samanpituisia keskenään. Käyttöjärjestelmänä projektissa käytetään Linuxia. Suunnittelu alkoi keväällä 2007 ja toimiva prototyyppi oli valmis alkusyksystä. Prototyypin testaus osoitti, että tietokonekortti kykenee täyttämään kaikki asiakkaan vaatimukset. Prototyypin testauksessa löytyneet viat ja optimoinnit on tarkoitus korjata tuotantomalliin, joten se antaa hyvän pohjan jatkosuunnittelua varten.

Protocol Specific Embedded Operating System

Sulautettujen järjestelmien määrä kuten niiden sisältämä älykkyyskin ovat viime vuosina kasvaneet merkittävästi. Sulautettujen ohjelmistojen yleistymistä ja monipuolistumista on edesauttanut sulautettujen laitteistojen prosessointitehon merkittävä kehittyminen, jonka myötä entistä vaativampien ohjelmistojen totetuttaminen sulautetusti on mahdollistunut. Seuraavana sulautettujen järjestelmien kehitysaskeleena on nähtävissä järjestelmien kommunikointikyvyn paraneminen ja siten uusien ja uudentyyppisten sulautettujen ratkaisujen toteuttaminen. VTT on päättänyt tutkia sulautettujen järjestelmien kommunikointia ja kehittää sulautettun protokolla-alustan. Tutkimuksen perusta on CVOPS protokollajärjestelmä, jota jatkokehittämällä pyritään toteuttamaan sulautettu protokollajärjestelmä, µCVOPS. Tässä diplomityössä esitetään kommunikaation sulautetulle järjestelmälle asettamia vaatimuksia, järjestelmän suunnittelu ja prototyypitys sulautetulla laitteistolla. Prototyypitykseen on käytetty sulautettua DragonBall mikrokontrolleria jonka käyttöjärjestelmänä käytettiin sulautettua Linux:a. Tälle alustalle on tehty CVOPS:sta modifioitu versio, jolla µCVOPS:ia pystytään simuloimaan.

A Co-Processor Approach for Efficient Java Execution in Embedded Systems

This thesis deals with a hardware accelerated Java virtual machine, named REALJava. The REALJava virtual machine is targeted for resource constrained embedded systems. The goal is to attain increased computational performance with reduced power consumption. While these objectives are often seen as trade-offs, in this context both of them can be attained simultaneously by using dedicated hardware. The target level of the computational performance of the REALJava virtual machine is initially set to be as fast as the currently available full custom ASIC Java processors. As a secondary goal all of the components of the virtual machine are designed so that the resulting system can be scaled to support multiple co-processor cores. The virtual machine is designed using the hardware/software co-design paradigm. The partitioning between the two domains is flexible, allowing customizations to the resulting system, for instance the floating point support can be omitted from the hardware in order to decrease the size of the co-processor core. The communication between the hardware and the software domains is encapsulated into modules. This allows the REALJava virtual machine to be easily integrated into any system, simply by redesigning the communication modules. Besides the virtual machine and the related co-processor architecture, several performance enhancing techniques are presented. These include techniques related to instruction folding, stack handling, method invocation, constant loading and control in time domain. The REALJava virtual machine is prototyped using three different FPGA platforms. The original pipeline structure is modified to suit the FPGA environment. The performance of the resulting Java virtual machine is evaluated against existing Java solutions in the embedded systems field. The results show that the goals are attained, both in terms of computational performance and power consumption. Especially the computational performance is evaluated thoroughly, and the results show that the REALJava is more than twice as fast as the fastest full custom ASIC Java processor. In addition to standard Java virtual machine benchmarks, several new Java applications are designed to both verify the results and broaden the spectrum of the tests.

Conceptual Design of Embedded Weather Display

The objective of this thesis work is to describe the Conceptual Design process of an embedded electronic display device. The work presents the following sub processes: definition of device specifications, introduction to the technological alternatives for system components and their comparison, comparative photometric measurements of selected display panels, and the design and building of a functional concept prototype. This work focuses mainly on electronics design, albeit the mechanical issues and fields of the software architecture that significantly affect the decisions are also discussed when necessary. The VESA Flat Panel Display Measurement (FPDM) 2.0 Standard was applied to the appropriate extent into photometric measurements. The results were analyzed against the requirement standards of a customer-specific display development project. An Active Matrix LCD was selected as the display of concept prototype, but also the excellent visual characteristics of Active Matrix OLED technology were noted. Should the reliability of the OLED products be significantly improved in the future, utilizing such products in the described application must be reconsidered.

Literature review on permanent magnet generators design and dynamic behavior

This paper is a literature review which describes the construction of state of the art of permanent magnet generators and motors constructing and discusses the current and possible application of these machines in industry. Permanent magnet machines are a well-know class of rotating and linear electric machines used for many years in industrial applications. A particular interest for permanent magnet generators is connected with wind mills, which seem to be becoming increasingly popular nowadays. Geared and direct-driven permanent magnet generators are described. A classification of direct-driven permanent magnet generators is given. Design aspects of permanent magnet generators are presented. Permanent magnet generators for wind turbines designs are highlighted. Dynamics and vibration problems of permanent magnet generators covered in literature are presented. The application of the Finite Element Method for mechanical problems solution in the field of permanent magnet generators is discussed.

Overvoltage Mitigation Techniques in Wind Power Generators

Advancements in power electronic semiconductor switching devices have lead to significantly faster switching times. In motor and generator applications, the fast switching times of pulse width modulated (PWM) inverters lead to overvoltages caused by voltage reflections with shorter and shorter cables. These excessive overvoltages may lead to a failure of the electrical machine in a matter of months. In this thesis, the causes behind the overvoltage phenomenon as well as its different mitigation techniques are studied. The most suitable techniques for mitigating the overvoltage phenomenon in wind power generator applications are chosen based on both simulations and actual measurements performed on a prototype. An RC filter at the terminals of the electrical machine and an inverter output filter designed to reduce the rise and fall times of voltage pulses are presented as a solution to the overvoltage problem. The performance and losses of both filter types are analysed.

Assembly Methods of Permanent Magnets for Synchronous Generators

This thesis examines and explains the procedure used to redesign the attachment of permanent magnets to the surface of the rotor of a synchronous generator. The methodology followed to go from the actual assembly to converge to the final purposed innovation was based on the systematic approach design. This meant that first a series of steps had to be predefined as a frame of reference later to be used to compare and select proposals, and finally to obtain the innovation that was sought. Firstly, a series of patents was used as the background for the upcoming ideas. To this end, several different patented assemblies had been found and categorized according the main element onto which this thesis if focused, meaning the attachment element or method. After establishing the technological frame of reference, a brainstorm was performed to obtain as many ideas as possible. Then these ideas were classified, regardless of their degree of complexity or usability, since at this time the quantity of the ideas was the important issue. Subsequently, they were compared and evaluated from different points of view. The comparison and evaluation in this case was based on the use of a requirement list, which established the main needs that the design had to fulfill. Then the selection could be done by grading each idea in accordance with these requirements. In this way, one was able to obtain the idea or ideas that best fulfilled these requirements. Once all of the ideas were compared and evaluated, the best or most suitable idea or ideas were separated. Finally, the selected idea or ideas was/were analyzed in extension and a number of improvements were made. Consequently, a final idea was refined and made more suitable at its performance, manufacture, and life cycle assessment. Therefore, in the end, the design process gave a solution to the problem pointed out at the beginning.

Ancillary services market and potential profit for generators in Russia

Reformation of electricity markets has initiated creation of ancillary services markets all over the world. The Russian electricity market reform is in transition period, that is why the problem of ancillary services market has just arisen. Since the model of market rules was created, ancillary services market became a topical question for generating companies. This master’s thesis is focused on the describing the possible ancillary services around the world and in Russia specifically. Moreover, the physical interpretation of ancillary services is defined. In addition, possibility of generation company to participate in the ancillary services market was considered. Calculations were made for primary frequency regulation service, where necessary level of price bids and payback period were evaluated.

Embedded controller system in crane application

The thesis studies possibility of using embedded controller in a crane application and furthermore defines requirements when designing such a controller. Basic crane control architectures are considered and compared. Then embedded controller product life cycle is described: considering such issues like microcontroller selection, software/hardware design and application development tools. Finally, available embedded controller is described and used for implementing crane control.

Customized agile development process for embedded software development

Agile software development has grown in popularity starting from the agile manifesto declared in 2001. However there is a strong belief that the agile methods are not suitable for embedded, critical or real-time software development, even though multiple studies and cases show differently. This thesis will present a custom agile process that can be used in embedded software development. The reasons for presumed unfitness of agile methods in embedded software development have mainly based on the feeling of these methods providing no real control, no strict discipline and less rigor engineering practices. One starting point is to provide a light process with disciplined approach to the embedded software development. Agile software development has gained popularity due to the fact that there are still big issues in software development as a whole. Projects fail due to schedule slips, budget surpassing or failing to meet the business needs. This does not change when talking about embedded software development. These issues are still valid, with multiple new ones rising from the quite complex and hard domain the embedded software developers work in. These issues are another starting point for this thesis. The thesis is based heavily on Feature Driven Development, a software development methodology that can be seen as a runner up to the most popular agile methodologies. The FDD as such is quite process oriented and is lacking few practices considered commonly as extremely important in agile development methodologies. In order for FDD to gain acceptance in the software development community it needs to be modified and enhanced. This thesis presents an improved custom agile process that can be used in embedded software development projects with size varying from 10 to 500 persons. This process is based on Feature Driven Development and by suitable parts to Extreme Programming, Scrum and Agile Modeling. Finally this thesis will present how the new process responds to the common issues in the embedded software development. The process of creating the new process is evaluated at the retrospective and guidelines for such process creation work are introduced. These emphasize the agility also in the process development through early and frequent deliveries and the team work needed to create suitable process.

Design of marine generators for alternative diesel-electric power systems

This study compares different electric propulsion systems. Results of the analysis of all the advantages and disadvantages of the different propulsion systems are given. This thesis estimates possibilities to apply different diesel-electric propulsion concepts for different vessel types. Small and medium size vessel’s power ranges are studied. The optimal delivery system is chosen. This choice is made on the base of detailed study of the concepts, electrical equipment market and comparison of mass, volume and efficiency parameters. In this thesis three marine generators are designed. They are: salient pole synchronous generator and two permanent magnet synchronous generators. Their electrical, dimensional, cost and efficiency parameters are compared. To understand all the benefits diagrams with these parameters are prepared. Possible benefits and money savings are estimated. As the result the advantages, disadvantages and boundary conditions for the permanent magnet synchronous generator application in marine electric-power systems are found out.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.