Effects of pulp electrochemistry on PGE flotation in sulphide poor ores

This work gives a reader basic knowledge about mineralogy and mineral processing. Main focus of this work was on flotation process and pulp electrochemistry on flotation. Three different sulphide poor ores are examined on experimental part. Platinum and palladium were the noble metals, which were contained into studied ores. Electrochemistry of flotation of PGE minerals on sulphide poor ores has been examined only slightly. Bench scale flotation test was used in this study. Chalcopyrite, nickel-pentlandite, pyrite, platinum and pH electrodes were used to investigation of pulp electrochemistry during flotation tests. Effects of grinding media, carbon dioxide atmosphere in grinding and mixture of carbon dioxide and air as flotation gas to PGE flotation and electrochemistry of flotation were studied. Stainless steel grinding media created more oxidising pulp environment to flotation than mild steel grinding media. Concentrate quality improved also with stainless steel grinding media, but the recovery was remarkably poorer, than with mild steel grinding media. Carbon dioxide atmosphere in grinding created very reducing pulp environment, which caused very good concentrate quality. But the recovery was again poorer than with normal mild steel grinding media. Mixture of carbon dioxide and air as flotation gas improved PGE recovery with some ores, but not always. Effect of carbon dioxide to pulp electrochemistry was detected mainly via pH-value.

Potentiometric titration as a method of determining the stoichiometric dissociation constants of weak acids from the thermodynamic dissociation constants of aqueous solutions at 298.15 K

The simple single-ion activity coefficient equation originating from the Debye-Hückel theory was used to determine the thermodynamic and stoichiometric dissociation constants of weak acids from data concerning galvanic cells. Electromotive force data from galvanic cells without liquid junctions, which was obtained from literature, was studied in conjuction with the potentiometric titration data relating to aqueous solutions at 298.15 K. The dissociation constants of weak acids could be determined by the presented techniques and almost all the experimental data studied could be interpreted within the range of experimental error. Potentiometric titration has been used here and the calculation methods were developed to obtain the thermodynamic and stoichiometric dissociation constants of some weak acids in aqueous solutions at 298.15 K. The ionic strength of titrated solutions were adjusted using an inert electrolyte, namely, sodium or potassium chloride. Salt content alonedetermines the ionic strength. The ionic strength of the solutions studied varied from 0.059 mol kg-1 to 0.37 mol kg-1, and in some cases up to 1.0 mol kg-1. The following substances were investigated using potentiometric titration: aceticacid, propionic acid, L-aspartic acid, L-glutamic acid and bis(2,2-dimethyl-3-oxopropanol) amine.

Saostuman esto prosessiputken pinnalle

Työn tarkoituksena oli tutkia kirjallisuudessa esitettyjen menetelmien soveltuvuutta estää kalsiumkarbonaatin saostuminen PCC – prosessissa paperikonelinjan massansyöttöputkessa. Menetelmien heikkoudet ja toimivuudet arvioitiin lähdetietojen perusteella, joiden perusteella tehtiin johtopäätelmiä niiden toimivuudesta prosessissa ja käytettävyydestä kalsiumkarbonaattisaostuman muodostumiseen. Kirjallisuusselvitys osoittaa, että saostuma voidaan estää kemiallisesti ja sähkökemiallisesti sekä modifioimalla materiaalipintaa. Lisäksi sen muodostuminen voidaan estää ultraääniaaltojen avulla sekä indusoimalla mahdolliseen saostuskohtaan magneetti- tai sähkökenttä. Kokeellisessa osassa keskityttiin kirjallisuuden perusteella tutkimaan kalsiumkarbonaatin saostumista kaupallisilla menetelmillä. Tutkimuksissa käytettiin erilaisia pinnoitemateriaaleja, ultraääniaaltoja sekä magneettikenttää että liuossähkökemiaa. Näiden lisäksi tutkittiin saostumisen kehittymistä putkipinnalle ajan funktiona. Kokeellisten tulosten perusteella kirjallisuudessa esitetyistä menetelmistä ei suoraan mikään sovellu sellaisenaan tutkitussa prosessissa saostuman muodostumisen estoon. Koeparametrien optimointi muuttamalla tunnettuja parametreja prosessitilanteeseen paransi kalsiumkarbonaatin liukoisuutta. Tämän tutkimuksen tuloksena löytyi menetelmäkuvaus, jolla saostumien muodostuminen putkipinnoille voidaan estää.

Synthesis, characterization and chemical sensor application of conducting polymers

Polymeric materials that conduct electricity are highly interesting for fundamental studies and beneficial for modern applications in e.g. solar cells, organic field effect transistors (OFETs) as well as in chemical and bio‐sensing. Therefore, it is important to characterize this class of materials with a wide variety of methods. This work summarizes the use of electrochemistry also in combination with spectroscopic methods in synthesis and characterization of electrically conducting polymers and other π‐conjugated systems. The materials studied in this work are intended for organic electronic devices and chemical sensors. Additionally, an important part of the presented work, concerns rational approaches to the development of water‐based inks containing conducting particles. Electrochemical synthesis and electroactivity of conducting polymers can be greatly enhanced in room temperature ionic liquids (RTILs) in comparison to conventional electrolytes. Therefore, poly(para‐phyenylene) (PPP) was electrochemically synthesized in the two representative RTILs: bmimPF6 and bmiTf2N (imidazolium and pyrrolidinium‐based salts, respectively). It was found that the electrochemical synthesis of PPP was significantly enhanced in bmimPF6. Additionally, the results from doping studies of PPP films indicate improved electroactivity in bmimPF6 during oxidation (p‐doping) and in bmiTf2N in the case of reduction (n‐doping). These findings were supported by in situ infrared spectroscopy studies. Conducting poly(benzimidazobenzophenanthroline) (BBL) is a material which can provide relatively high field‐effect mobility of charge carriers in OFET devices. The main disadvantage of this n‐type semiconductor is its limited processability. Therefore in this work BBL was functionalized with poly(ethylene oxide) PEO, varying the length of side chains enabling water dispersions of the studied polymer. It was found that functionalization did not distract the electrochemical activity of the BBL backbone while the processability was improved significantly in comparison to conventional BBL. Another objective was to study highly processable poly(3,4‐ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) water‐based inks for controlled patterning scaled‐down to nearly a nanodomain with the intention to fabricate various chemical sensors. Developed PEDOT:PSS inks greatly improved printing of nanoarrays and with further modification with quaternary ammonium cations enabled fabrication of PEDOT:PSS‐based chemical sensors for lead (II) ions with enhanced adhesion and stability in aqueous environments. This opens new possibilities for development of PEDOT:PSS films that can be used in bio‐related applications. Polycyclic aromatic hydrocarbons (PAHs) are a broad group of π‐conjugated materials consisting of aromatic rings in the range from naphthalene to even hundred rings in one molecule. The research on this type of materials is intriguing, due to their interesting optical properties and resemblance of graphene. The objective was to use electrochemical synthesis to yield relatively large PAHs and fabricate electroactive films that could be used as template material in chemical sensors. Spectroscopic, electrochemical and electrical investigations evidence formation of highly stable films with fast redox response, consisting of molecules with 40 to 60 carbon atoms. Additionally, this approach in synthesis, starting from relatively small PAH molecules was successfully used in chemical sensor for lead (II).

Review of water electrolysis technologies and design of renewable hydrogen production systems

An electric system based on renewable energy faces challenges concerning the storage and utilization of energy due to the intermittent and seasonal nature of renewable energy sources. Wind and solar photovoltaic power productions are variable and difficult to predict, and thus electricity storage will be needed in the case of basic power production. Hydrogen’s energetic potential lies in its ability and versatility to store chemical energy, to serve as an energy carrier and as feedstock for various industries. Hydrogen is also used e.g. in the production of biofuels. The amount of energy produced during hydrogen combustion is higher than any other fuel’s on a mass basis with a higher-heating-value of 39.4 kWh/kg. However, even though hydrogen is the most abundant element in the universe, on Earth most hydrogen exists in molecular forms such as water. Therefore, hydrogen must be produced and there are various methods to do so. Today, the majority hydrogen comes from fossil fuels, mainly from steam methane reforming, and only about 4 % of global hydrogen comes from water electrolysis. Combination of electrolytic production of hydrogen from water and supply of renewable energy is attracting more interest due to the sustainability and the increased flexibility of the resulting energy system. The preferred option for intermittent hydrogen storage is pressurization in tanks since at ambient conditions the volumetric energy density of hydrogen is low, and pressurized tanks are efficient and affordable when the cycling rate is high. Pressurized hydrogen enables energy storage in larger capacities compared to battery technologies and additionally the energy can be stored for longer periods of time, on a time scale of months. In this thesis, the thermodynamics and electrochemistry associated with water electrolysis are described. The main water electrolysis technologies are presented with state-of-the-art specifications. Finally, a Power-to-Hydrogen infrastructure design for Lappeenranta University of Technology is presented. Laboratory setup for water electrolysis is specified and factors affecting its commissioning in Finland are presented.

Mineraalien rikastusprosessin vesijalanjälki

Mineraalien rikastamiseen käytetään useita fysikaalisia ja kemiallisia menetelmiä. Prosessi sisältää malmin hienonnuksen, rikastuksen ja lopuksi vedenpoistamisen rikastelietteestä. Malmin rikastamiseen käytetään muun muassa vaahdotusta, liuotusta, magneettista rikastusta ja tiheyseroihin perustuvia rikastusmenetelmiä. Rikastuslietteestä voidaan poistaa vettä sakeuttamalla ja suodattamalla. Rikastusprosessin ympäristövaikutuksia voidaan arvioida laskemalla tuotteen vesijalanjälki, joka kertoo valmistamiseen kulutetun veden määrän. Tässä kirjallisuustyössä esiteltiin mineraalien käsittelymenetelmiä sekä prosessijätevesien puhdistusmenetelmiä. Kirjallisuuslähteiden pohjalta selvitettiin Pyhäsalmen kaivoksella valmistetun kuparianodin vesijalanjälki sekä esitettiin menetelmiä, joilla prosessiin tarvittavan raakaveden kulutusta voitaisiin vähentää. Pyhäsalmella kuparirikasteesta valmistetun kuparianodin vesijalanjälki on 240 litraa H2O ekvivalenttia tuotettua tonnia kohden. Pyhäsalmen prosessin raakaveden kulutusta voidaan vähentää lisäämällä sisäistä vedenkierrätystä. Kalsiumsulfaatin saostuminen putkiin ja pumppuihin on ilmentynyt ongelmaksi vedenkierrätyksen lisäämisessä. Kalsiumsulfaattia voidaan erottaa vedestä membraaneihin, ioninvaihtoon ja sähkökemiaan perustuvilla tekniikoilla. Vaihtoehdossa, jossa johdetaan kaikista kolmesta vaahdotuksesta saatavat rikastuslietteen ja rikastushiekan sakeutuksien ylitteet sekä suodatuksien suodosvedet samaan vedenkäsittelyyn voidaan kattaa arviolta noin 65 % koko veden tarpeesta. Raakavettä säästetään vuodessa 3,4 Mm^3 ja samalla rikastushiekka-altaiden tarvittava koko pienenee, joka vähentää ympäristöriskejä.