Membrane emulsification in preparation of single site catalyst

In the theory part the membrane emulsification was studied. Emulsions are used in many industrial areas. Traditionally emulsions are prepared by using high shear in rotor-stator systems or in high pressure homogenizer systems. In membrane emulsification two immiscible liquids are mixed by pressuring one liquid through the membrane into the other liquid. With this technique energy could be saved, more homogeneous droplets could be formed and the amount of surfactant could be decreased. Ziegler-Natta and single-site catalysts are used in olefin polymerization processes. Nowadays, these catalysts are prepared according to traditional mixing emulsification. More homogeneous catalyst particles that have narrower particle size distribution might be prepared with membrane emulsification. The aim of the experimental part was to examine the possibility to prepare single site polypropylene catalyst using membrane emulsification technique. Different membrane materials and solidification techniques of the emulsion were examined. Also the toluene-PFC phase diagram was successfully measured during this thesis work. This phase diagram was used for process optimization. The polytetrafluoroethylene membranes had the largest contact angles with toluene and also the biggest difference between the contact angles measured with PFC and toluene. Despite of the contact angle measurement results no significant difference was noticed between particles prepared using PTFE membrane or metal sinter. The particle size distributions of catalyst prepared in these tests were quite wide. This would probably be fixed by using a membrane with a more homogeneous pore size distribution. It is also possible that the solidification rate has an effect on the particle sizes and particle morphology. When polymeric membranes are compared PTFE is probably still the best material for the process as it had the best chemical durability.

Eräiden paperinvalmistuksessa käytettävien vahadispersioiden stabiilisuuden hallinta

Diplomityön tavoitteena oli selvittää millainen laaduntarkastus AKD-dispersioille tulisi suorittaa kuormien vastaanotossa ja tulisiko dispersioiden laatu tarkastaa uudelleen ennen annostelua. Tätä varten seurattiin toimituserien laadun tasaisuutta ja tarkasteltiin varastointiolosuhteiden vaikutusta dispersioiden säilyvyyteen. Lisäksi kartoitettiin dispersioiden käsittelyssä ja kartonginvalmistusprosessissa esiintyvien riskitekijöiden vaikutuksia kaupallisten dispersioiden stabiilisuuteen. Kirjallisuusosassa perehdyttiin kolloidisiin dispersioihin sekä niiden stabiilisuuteen vaikuttaviin tekijöihin. AKD-dispersiot valmistetaan emulgointitekniikoiden avulla, joten dispergointimenetelmien ohella käsiteltiin myös emulsioiden valmistamista. Lisäksi luotiin katsaus dispersioteknologian tärkeimpiin analyysimenetelmiin. Alkyyliketeenidimeerin osalta käsiteltiin emulgoinnin lisäksi vahan ja muiden lisäaineiden vaikutuksia dispersioiden stabiilisuuteen ja myös niiden merkitystä dispersioiden formuloinnissa. AKD-liimauksen osalta esiin tuotiin AKD:n tärkeimmät reaktiomekanismit, sillä ne liittyvät osittain myös dispersioiden stabiilisuuteen. Lopuksi luotiin lyhyt katsaus AKD-dispersioiden stabiilisuutta käsittelevään tutkimukseen, jota on toistaiseksi julkaistu varsin niukasti. Kokeellisessaosassa tarkastelun kohteeksi valittiin neljä kaupallista alkyyliketeenidimeerinvesidispersiota, joiden koostumus ja ominaisuudet selvitettiin perusteellisesti. Tarkoituksena oli auttaa ymmärtämään dispersioiden stabiilisuudessa mahdollisesti esiintyviä eroja. Laajamittainen dispersioiden karakterisointi näyttää olevan tarpeen ainakin otettaessa uutta AKD-laatua käyttöön, sillä dispersioiden koostumus ja ominaisuudet voivat vaihdella merkittävästi. AKD-dispersioiden laadussa esiintyi vaihtelua eri toimituserien välillä. Suurimmat vaihtelut havaittiin dispersioiden varaustiloissa ja partikkelikokojakaumissa. Laadun epätasaisuuden vuoksi vastaanottotarkastuksen merkitys korostuu. Vastaanottotarkastuksessa syytä olisi kiinnittää dispersion kuiva-ainepitoisuuden ohella sen viskositeettiin, varaustilaan, tehoainepitoisuuteen sekä rakenteeseen. Rakenteen tarkastelussa optinen mikroskooppi voi rutiininomaisessa seurannassa korvata partikkelikokojakauman määrittämisen. Varastointilämpötilan vaikutus dispersioidenlaatuun on merkittävä. Dispersiot säilyvät parhaiten viileässä, joten jos varastosäiliöissä ei ole jäähdytystä, on dispersioiden laadun tarkastus tarpeen myös ennen annostelua. Jotta dispersion kunnosta saadaan luotettava arvio, on viskositeetin määrittämiseen yhdistettävä vähintään rakenteen tarkastelu optisella mikroskoopilla. Mekaaninen rasitus voi dominoivasta stabilointimekanismistariippuen aiheuttaa dispersiossa hienoaineen muodostumista tai partikkelien flokkaantumista. Stabilointimekanismi vaikuttaa niin ikään partikkelien käyttäytymiseen korkeissa lämpötiloissa. Dispersioiden stabiilisuuden todettiin heikkenevän pH:n kohotessa emäksiselle alueelle. Elektrolyyttikonsentraatio vaikuttaa partikkelien mikroelektroforeettiseen ioniliikkuvuuteen merkittävästi. Kartonkikoneen märkäosan kemikaaleista anionisen retentioaineen (BMA) todettiin vuorovaikuttavan kationisten AKD-partikkelien kanssa selvimmin. Mikroelektroforeettisen ioniliikkuvuuden mittaaminen kiertovedessä todettiin tärkeäksi, sillä se kuvaa dispersion käyttäytymistä sen käyttöympäristössä.

The use of branched ketenedimers in solving the deposit problems related to the internal sizing of uncoated fine paper

Alkyl ketene dimers (AKD) are effective and highly hydrophobic sizing agents for the internal sizing of alkaline papers, but in some cases they may form deposits on paper machines and copiers. In addition, alkenyl succinic anhydrides (ASA)- based sizing agents are highly reactive, producing on-machine sizing, but under uncontrolled wet end conditions the hydrolysis of ASA may cause problems. This thesis aims at developing an improved ketene dimer based sizing agent that would have a lower deposit formation tendency on paper machines and copiers than a traditional type of AKD. The aim is also to improve the ink jet printability of a AKD sized paper. The sizing characteristics ofketene dimers have been compared to those of ASA. A lower tendency of ketene dimer deposit formation was shown in paper machine trials and in printability tests when branched fatty acids were used in the manufacture of a ketene dimer basedsizing agent. Fitting the melting and solidification temperature of a ketene dimer size to the process temperature of a paper machine or a copier contributes to machine cleanliness. A lower hydrophobicity of the paper sized with branched ketene dimer compared to the paper sized with traditional AKD was discovered. However, the ink jet print quality could be improved by the use of a branched ketene dimer. The branched ketene dimer helps in balancing the paper hydrophobicity for both black and color printing. The use of a high amount of protective colloidin the emulsification was considered to be useful for the sizing performance ofthe liquid type of sizing agents. Similar findings were indicated for both the branched ketene dimer and ASA.

Studies in offset ink setting

The offset printing process is complex and involves the meeting of two essentially complex materials, printing ink and paper, upon which the final product is formed. It can therefore be expected that a multitude of chemical and physical interactions and mechanisms take place at the ink-paper interface. Interactions between ink and paper are of interest to both the papermakers and ink producers, as they wish to achieve better quality in the final product. The objective of this work is to clarify the combined influence of paper coating structure, printing ink and fountain solution on ink setting and the problems related to ink setting. A further aim is to identify the mechanisms that influence ink setting problems, and to be able to counteract them by changing properties of the coating layer or by changing the properties of the ink. The work carried out for this thesis included use of many techniques ranging from standard paper and printability tests to advanced optical techniques for detection of ink filaments during ink levelling. Modern imaging methods were applied for assessment of ink filament remain sizes and distribution of ink components inside pigment coating layers. Gravimetric filtration method and assessment of print rub using Ink-Surface-Interaction-Tester (ISIT) were utilized to study the influence of ink properties on ink setting. The chemical interactions were observed with the help of modified thin layer chromatography and contact angle measurements using both conventional and high speed imaging. The results of the papers in this thesis link the press operational parameters to filament sizes and show the influence of these parameters to filament size distribution. The relative importance between the press operation parameters was shown to vary. The size distribution of filaments is important in predicting the ink setting behaviour, which was highlighted by the dynamic gloss and ink setting studies. Prediction of ink setting behaviour was also further improved by use of separate permeability factors for different ink types in connection to filtration equations. The roles of ink components were studied in connection to ink absorption and mechanism of print rub. Total solids content and ratio of linseed oil to mineral oil were found to determine the degree of print rub on coated papers. Wax addition improved print rub resistance, but would not decrease print rub as much as lowering the total solids content in the ink. Linseed oil was shown to absorb into pigment coating pores by mechanism of adsorption to pore walls, which highlights the need for sufficient pore surface area for improved chromatographic separation of ink components. These results should help press operators, suppliers of printing presses, papermakers and suppliers to papermakers, to better understand the material and operating conditions of the press as it relates to various print quality issues. Even though paper is in competition with electronic media, high quality printed products are still in demand. The results should provide useful information for this segment of the industry.