Reduction and Analysis Methods of Indigo

Throughout history indigo was derived from various plants for example Dyer’s Woad (Isatis tinctoria L.) in Europe. In the 19th century were the synthetic dyes developed and nowadays indigo is mainly synthesized from by-products of fossil fuels. Indigo is a so-called vat dye, which means that it needs to be reduced to its water soluble leucoform before dyeing. Nowadays, most of the industrial reduction is performed chemically by sodium dithionite. However, this is considered environmentally unfavourable because of waste waters contaminating degradation products. Therefore there has been interest to find new possibilities to reduce indigo. Possible alternatives for the application of dithionite as the reducing agent are biologically induced reduction and electrochemical reduction. Glucose and other reducing sugars have recently been suggested as possible environmentally friendly alternatives as reducing agents for sulphur dyes and there have also been interest in using glucose to reduce indigo. In spite of the development of several types of processes, very little is known about the mechanism and kinetics associated with the reduction of indigo. This study aims at investigating the reduction and electrochemical analysis methods of indigo and give insight on the reduction mechanism of indigo. Anthraquinone as well as it’s derivative 1,8-dihydroxyanthraquinone were discovered to act as catalysts for the glucose induced reduction of indigo. Anthraquinone introduces a strong catalytic effect which is explained by invoking a molecular “wedge effect” during co-intercalation of Na+ and anthraquinone into the layered indigo crystal. The study includes also research on the extraction of plant-derived indigo from woad and the examination of the effect of this method to the yield and purity of indigo. The purity has been conventionally studied spectrophotometrically and a new hydrodynamic electrode system is introduced in this study. A vibrating probe is used in following electrochemically the leuco-indigo formation with glucose as a reducing agent.

Taivekartongin sävytys ja jälkikellertyminen

Taivekartongilta vaaditaan nykyisin korkealaatuista ja tasaista ulkonäköä. Pakkauksen tehtävänä on parantaa myyntiä hyvällä ulkonäöllä ja siisteydellä sekä antaa informaatiota ja käyttöohjeita. Tässä diplomityössä tutkittiin taivekartongin sävyttämistä, optisia ominaisuuksia sekä vaaleuden ja sävyjen pysyvyyttä. Kirjallisuusosassa käsiteltiin paperin ja kartongin optisia ominaisuuksia sekä esiteltiin Kubelka-Munkin teoria. Teoriaa voidaan käyttää mm. monikerroskartongin vaaleuden ja sävyjen mallintamisessa. Esillä oli paljon eri prosessitekijöitä, massoja ja kemikaaleja, jotka vaikuttavat kartongin vaaleuteen ja sävyyn. Työssä kärsiteltiin myös keinoja vaikuttaa kartongin sävyyn sävytyksellä ja sävytyksen eri tapoja. Toisaalta vaaleuden ja sävyn pysyvyyteen vaikuttaa kartongin jälkikellertyminen. Työssä tarkasteltiin jälkikellertymisen mekanismeja ja siihen vaikuttavia tekijöitä sekä esitettiin keinoja ennalta ehkäistä ja estää kellertymistä. Kokeellisessa osassa käsiteltiin massan ja päällystyspastan värjäyksen vaikutuksia ulkonäköön ja optisiin ominaisuuksiin. Sinertävillä tai violeteilla sävyväreillä voidaan pienentää mekaanisten massojen luonnollista kellertyvyyttä, jolloin valkoisuuden vaikutelma lisääntyy. Värien lisääminen heikentää vaaleutta, koska värien lisäys nostaa valon absorptiota. Tämän takia on tärkeää lisätä väri mielellään siihen kerrokseen, jossa kellertävä massa on, joka on tyypillisesti kartongin keskikerros. Pintakerrokset ovat valkaistua sellua ja niillä on tärkeä merkitys kartongin vaaleudelle, joten värin lisäys pintaan alentaisi vielä merkittävämmin kartongin kokonaisvaaleutta. Pastan värjäyksellä saadaan tasaisuutta värjäykseen, mutta sävyn säätö on tehtävä edelleen massavärjäyksellä. Pigmenttivärien käytöllä pystytään lisäämään mm. valonkestoa kartongille. Kartongin ja paperituotteiden valonkeston tutkimiseen ei ole olemassa standardia. Työssä tutkittiin laboratorio-olosuhteissa ja huonevalossa vanhentuneiden kartonkinäytteiden vertailtavuutta. Materiaalivalinnoilla pystytään vaikuttamaan valon-kestoon. Siihen vaikuttavat mm. massan laatu, lateksivalinta sekä pigmenttivärin käyttö. Mekaanista massaa sisältävät tuotteet kellertyvät pääasiassa ligniinin takia. Ligniini sisältää paljon UV-säteilyyn reagoivia ryhmiä, jotka muuttuvat värilliseksi lisäten kellertymistä. Valkaistujen sellujen vanhentuminen on suhteessa mekaaniseen massaan erittäin vähäistä. SA-lateksin havaittiin suojaavan vaaleuden menetykseltä ja lisäävän sävyn pysyvyyttä paremmin kuin SB-lateksi.

Mellom tradisjon og spel : didaktikk for tekstil folkekunst

Denne avhandlinga er resultatet av eit behov for å forske på og utvikle ein didaktikk for tekstilfaget ved Folkekunststudiet, Institutt for folkekultur, Høgskolen i Telemark, Noreg. Studiet med folkekunst som fagfelt er eit relativt ungt studium på høgskolen, som vart etablert i 1984. Problemstillinga i denne avhandlinga er korleis ein kan utvikle ein forskingsbasert didaktikk der dei grunnleggjande prinsippa som særmerkjer den tradisjonelle folkekunsten, vert tekne vare på. I arbeidet med avhandlinga har eg prøvd på å klårgjere problemstillinga ut frå ulike perspektiv. Forskingsarbeidet har fokus på kommunikasjon og arbeidsmåtar i ljos av ulike teoriar. Det er ei hermeneutisk tilnærming som er vald for den didaktiske forståinga. Det fyrste drøftingstemaet har søkjeljos på kommunikasjon og dialog ved vidareføring av tekstil folkekunst. Både estetiske, teoretiske, praktiske og sosiale aspekt er nedfelte i læreplanen for studiet og skal utgjere grunnlaget for kommunikasjon og arbeidsmåtar. I den skapande og kopierande prosessen er det utvikla språklege reiskapar for både den sosiale og den estetiske sida der den teoretiske og praktiske faktoren er integrert. Møte med døme på tekstile tradisjonar så vel som praktisk forming av tekstilar har ført til refleksjon og dialog som involverer kontemplasjon, korrespondens og imaginasjon. Det andre temaet som er drøfta, er vidareføring av tradisjonelt visuelt formspråk. Her er merksemda retta mot kva som har skjedd formalt med ei gruppe tradisjonelle formelement i tekstilar i den institusjonelle vidareføringa over eit lengre tidsperspektiv. Resultatet syner at mange tradisjonelle formelement er borte frå den institusjonelle produksjonen. Formelementa kan ha fått ei meir naturalistisk utforming, eller dei er overførte til andre tradisjonelle tekstilteknikkar enn dei som var utgangspunktet. Rombeforma i den institusjonelle produksjonen er utført i færre variasjonar og kombinasjonar enn i den tradisjonelle produksjonen. Konklusjonen på drøftingstemaet er at spelereglar og spatialitet i høve til den formale komponenten i utvalet med tradisjonelle tekstilar ikkje er vidareført i alle gruppene av institusjonelle produkt. Resultatet kan få innverknad og fylgjer for utforming av ein framtidig didaktikk for faget. Arbeidsmåte og erfaring frå vidareføring av tekstile tradisjonar er det tredje temaet som er drøfta i avhandlinga. Kopiering og skapande prosessar er arbeidsmåtar som er brukte ved studiet i dag, og dei utgjer grunnlag for drøftingar i relasjon til vidareføring og erfaring. Konklusjonen er at i den skapande prosessen korrigerer tradisjonen utforminga, medan i kopiprosessen er eigen stilvilje og improvisering resultat av prosessane. Personar som deltek i prosessane, har sett seg sjølve og si historiske forankring inn i spelet, der visuelt og verbalt språk er resultat av integrasjon av tradisjonar. Dei tre drøftingstemaa utgjer grunnlaget for at didaktikk for folkekunst og tekstil kan bli intersubjektiv forståing av kva ein didaktikk for vidareføring av folkekunst med vekt på tekstil kan vere i utdanninga i dag. Indre og ytre dialog i skapande og kopierande prosessar femner om estetiske, materielle og tekniske faktorar sett i høve til spelereglar, spelerom, spatialitet og samspel i møte med tekstile tradisjonar. Samla utgjer det ein forskingsbasert didaktikk for faget der den overordna intensjonen er samtykke mellom tradisjon og spel.

Ultrasound-assisted electrochemical treatment of wastewaters containing organic pollutants by using novel Ti/Ta2O5-SnO2 electrodes

Advanced oxidation processes (AOPs) are modern methods using reactive hydroxyl radicals for the mineralization of organic pollutants into simple inorganic compounds, such as CO2 and H2O. Among AOPs electrochemical oxidation (EO) is a method suitable for coloured and turbid wastewaters. The degradation of pollutants occurs on electrocatalytic electrodes. The majority of electrodes contain in their structure either expensive materials (diamond and Pt-group metals) or are toxic for the environment compounds (Sb or Pb). One of the main disadvantages of electrochemical method is the polarization and contamination of electrodes due to the deposition of reaction products on their surface, which results in diminishing of the process efficiency. Ultrasound combined with the electrochemical degradation process eliminates electrode contamination because of the continuous mechanical cleaning effect produced by the formation and collapse of acoustic cavitation bubbles near to the electrode surface. Moreover, high frequency ultrasound generates hydroxyl radicals at water sonolysis. Ultrasound-assisted EO is a non-selective method for oxidation of different organic compounds with high degradation efficiencies. The aim of this research was to develop novel sustainable and cost-effective electrodes working as electrocatalysts and test their activity in electrocatalytic oxidation of organic compounds such as dyes and organic acids. Moreover, the goal of the research was to enhance the efficiency of electrocatalytic degradation processes by assisting it with ultrasound in order to eliminate the main drawbacks of a single electrochemical oxidation such as electrodes polarization and passivation. Novel Ti/Ta2O5-SnO2 electrodes were developed and found to be electrocatalytically active towards water (with 5% Ta content, 10 oxide film layers) and organic compounds oxidation (with 7.5% Ta content, 8 oxide film layers) and therefore these electrodes can be applicable in both environmental and energy fields. The synergetic effect of combined electrolysis and sonication was shown while conducting sonoelectrochemical (EO/US) degradation of methylene blue (MB) and formic acid (FA). Complete degradation of MB and FA was achieved after 45 and 120 min of EO/US process respectively in neutral media. Mineralization efficiency of FA over 95% was obtained after 2 h of degradation using high frequency ultrasound (381, 863, 1176 kHz) combined with 9.1 mA/cm2 current density. EO/US degradation of MB provided over 75% mineralization in 8 h. High degradation kinetic rates and mineralization efficiencies of model pollutants obtained in EO/US experiments provide the preconditions for further extrapolation of this treatment method to pilot scale studies with industrial wastewaters.

Finnish buyers’ perceptions of Indian textile and clothing suppliers: Country of origin in focus

Choosing the right supplier is crucial for long-term business prospects and profitability. Thus organizational buyers are naturally very interested in how they can select the right supplier for their needs. Likewise, suppliers are interested in knowing how their customers make purchasing decisions in order to effectively sell and market to them. From the point of view of the textile and clothing (T&C) industry, regulatory changes and increasing low-cost and globalization pressures have led to the rise of low-cost production locations India and China as the world’s largest T&C producers. This thesis will examine T&C trade between Finland and India specifically in the context of non-industrial T&C products. Its main research problem asks: what perceptions do Finnish T&C industry buyers hold of India and Indian suppliers? B2B buyers use various supplier selection models and criteria in making their purchase decisions. A significant amount of research has been done into supplier selection practices, and in the context of international trade, country of origin (COO) perceptions specifically have garnered much attention. This thesis uses a mixed methods approach (online questionnaire and in-depth interviews) to evaluate Finnish T&C buyers’ supplier selection criteria, COO perceptions of India and experiences of Indian suppliers. It was found that the most important supplier selection criteria used by Finnish T&C buyers are quality, reliability and cost. COO perceptions were not found to be influential in purchasing process. Indian T&C suppliers’ strengths were found to be low cost, flexibility and a history of traditional T&C expertise. Their weaknesses include product quality and unreliable delivery times. Overall, the main challenges that need to be overcome by Indian T&C companies are logistical difficulties and the cost vs. quality trade-off. Despite positive perceptions of India for cost, the overall value offered by Indian T&C products was perceived to be low due to poor quality. Unreliable delivery time experiences also affected buyer’s reliability perceptions of Indian suppliers. The main limiting factors of this thesis relate to the small sample size used in the research. This limits the generalizability of results and the ability to evaluate the reliability and validity of some of the research instruments.

Perceptions of green branding and identity building amongst small Finnish textile producers

The textile industry is one of the most polluting industries in the world. The amount of air and water pollution it causes puts a burden on the environment. There are companies who have taken the environmental and social aspects into account in the their production and chosen to operate in a green manner. This thesis studies how the phenomenon of green branding is seen from the perspectives of small Finnish textile companies. The theory used in this thesis has to do with green branding and identity building. The theory is used to analyze the results of the empirical findings. The main research question that the thesis aims to answer is how green branding is perceived within the Finnish textile industry. In order to answer the main research question, empirical data was collected from five relevant companies within the Finnish textile industry. The companies interviewed for the study were WST, Saana ja Olli, RCM, R-collection and Tiensivu. The study was conducted as a multiple case based study where multiple experts from green companies were interviewed. The experts were all owners or employees of companies that have a so-called green brand identity. The data was collected through semi-structured interviews, where the relevant experts from each company were interviewed either by themselves, in pairs or in groups. The data that was collected for this study was primary data, and the results of the study are mainly based on the experiences and opinions of the experts interviewed. The data collected does not cover the entire green textile industry within Finland, but study does however give a fairly comprehensive view of the phenomenon, as the textile industry in Finland is quite concise. The general findings of the study show that all experts from the companies interviewed agreed that a green brand identity does benefit their company in one way or the other. The findings also show contradictions with the older theory (eg. Charter et al. 1999, Pickett et al. 1995), and perhaps give a more modern view of the thoughts within the industry.

Purification and fractionation by nanotiltration in dairy and sugar and sweetener industry applications

Nanotiltration is a membrane separation method known for its special characteristic of rejecting multivalent ions and passing monovalent ions. Thus, it is commonly applied with dilute aqueous solutions in partial salt removal, like in drinking water production. The possibilities of nanofiltration have been studied and the technique applied in a wide branch of industries, e.g. the pulp and paper, the textile and the chemical processing industry. However, most present applications and most of the potential applications studied involve dilute solutions, the permeating stream being generally water containing monovalent salts. In this study nanotiltration is investigated more as a fractionation method. A well-known application in the dairy industry is concentration and partial salt removal from whey. Concentration and partial demineralization is beneficial for futher processing of whey as whey concentrates are used e.g. in baby foods. In the experiments of this study nanotiltration effectively reduced the monovalent salts in the whey concentrate. The main concern in this application is lactose leakage into the permeate. With the nanofiltration membranes used the lactose retentions were practically ? 99%. Another dairy application studied was the purification and reuse of cleaning solutions. This is an environmentally driven application. An 80% COD reduction by nanofiltration was observed for alkaline cleaning-in-place solution. Nanofiltration is not as commonly applied in the sugar and sweeteners industry as in the dairy industry. In this study one potential application was investigated, namely xylose purification from hemicellulose hydrolyzate. Xylose is raw material for xylitol production. Xylose separation from glucose was initially studied with xylose-glucose model solutions. The ability of nanofiltration to partially separate xylose into the permeate from rather concentrated xylose-glucose solutions (10 w-% and 30 w-%) became evident. The difference in size between xylose and glucose molecules according to any size measure is small, e.g. the Stokes diameter of glucose is 0.73 nm compared to 0.65 nm for xylose. In further experiments, xylose was purified into nanoliltration permeate from a hemicellulose hydrolyzate solution. The xylose content in the total solids was increased by 1.4—1.7 fold depending on temperature, pressure and feed composition.

Fouling, prevention of fouling, and clearing in filtration

In this thesis fouling of conventional filter fabrics and membranes was studied. In the beginning of the thesis fouling and how it can be measured and predicted is reviewed. Information on different methods on how fouling canbe decreased or cleaned away is also given. The experimental part is divided into two sections; fabric filtration and membrane filtration. Fouling of the filter fabrics was studied with silica or cupper slurries and fouling of the membranes was studied with pulp and paper mill waters. The fouled filter materials were characterised according to many different methods. The most useful way to observe fouling is to measure the changes in the permeate flux. Fouling can also be seen visually e.g. with scanning electron microscopy. Consequently, also the reason for the fouling in question might be found. Different filtration characteristics affect fouling e.g. as the filtration pressure was increased it did not have much influence on the permeate flux, but the pressure caused the membrane to get fouled faster. Also, an increase of shear rate on the membrane surface decreased fouling. Different pretreatment methods for the effluent were tested in membrane filtration to decrease fouling. The tested methods; biological treatment, ozonation, enzymatic treatment and flocculation, did not have a clear influence on the fouling of the membrane, but e.g. a biological treatment combined with ultrafiltration made the tested groundwood mill circulation water purer than ultrafiltration alone.

Brightness of multilayer boards

A good appearance of a package enhances the sale of the product. The packing gives information about the content and instructions for the usage. In this master’s thesis, the optical properties of multilayer packaging board is studied. Especially means of increasing brightness of the multilayer board are evaluated. In the literature part, the effect of different factors on optical properties of a multilayer board are evaluated with the help of light scattering and absorption coefficients. The Kubelka-Munk theory can be used also in modelling brightness of the multilayer board. A large variety of different process factors, chemical aids and machine variables affect optical properties of board. In the experimental part, different methods to increase brightness of a 3-layer board were evaluated. It was discovered that brightness variation of broke (30 % share of the center layer pulp) have only minor influence on brightness of the board. The brightness variation must be high, roughly 9 % in order to alter brightness of the board by 1 %. Higher brightness can be achieved by bleaching the pulp, which holds the largest share of the center layer pulp. Here, 2,6 % increase in brightness of the pulp (60 % share of the center layer pulp) increased brightness of the board by 1 %. In a trial run at a board machine, there was no indication of decreased bulk of the board due to extended bleaching of the pulp. With pulp dyeing appearance and optical properties of a multilayer board can be influenced. By using bluish dyes the natural yellowness of pulps can be decreased and impression of whiteness is then increased. Brightness may deteriorate though, because of increasing light absorption of the dyed pulps. When the yellowness comes from the center layer pulp, the dye should be introduced there. Then the brightness decreasing effect of the dye decreases brightness of the board less. It was noticed that it is more important to maintain brightness of the top layer than brightness of the center layer, because the top layer pulp affects on brightness of the board the most. By introducing fillers into the top layer of a multilayer board it is possible to increase brightness of the board. Fillers with the highest light scattering increased the brightness of the board the most. Increasing light scattering increases brightness and also opacity. Higher opacity in the top layer decreases also the darkening effect of the center layer. Calcinated kaolin and PCC was found to increase the light scattering of the top layer the most at the filler comparison. Introducing fillers into the top layer of multilayer board may decrease bulk and modulus of elasticity of the top layer. This could lead to deteriorated bending stiffness.

Computational and Experimental Investigation of the Grooved Roll in Paper Machine Environment

In the paper machine, it is not a desired feature for the boundary layer flows in the fabric and the roll surfaces to travel into the closing nips, creating overpressure. In this thesis, the aerodynamic behavior of the grooved roll and smooth rolls is compared in order to understand the nip flow phenomena, which is the main reason why vacuum and grooved roll constructions are designed. A common method to remove the boundary layer flow from the closing nip is to use the vacuum roll construction. The downside of the use of vacuum rolls is high operational costs due to pressure losses in the vacuum roll shell. The deep grooved roll has the same goal, to create a pressure difference over the paper web and keep the paper attached to the roll or fabric surface in the drying pocket of the paper machine. A literature review revealed that the aerodynamic functionality of the grooved roll is not very well known. In this thesis, the aerodynamic functionality of the grooved roll in interaction with a permeable or impermeable wall is studied by varying the groove properties. Computational fluid dynamics simulations are utilized as the research tool. The simulations have been performed with commercial fluid dynamics software, ANSYS Fluent. Simulation results made with 3- and 2-dimensional fluid dynamics models are compared to laboratory scale measurements. The measurements have been made with a grooved roll simulator designed for the research. The variables in the comparison are the paper or fabric wrap angle, surface velocities, groove geometry and wall permeability. Present-day computational and modeling resources limit grooved roll fluid dynamics simulations in the paper machine scale. Based on the analysis of the aerodynamic functionality of the grooved roll, a grooved roll simulation tool is proposed. The smooth roll simulations show that the closing nip pressure does not depend on the length of boundary layer development. The surface velocity increase affects the pressure distribution in the closing and opening nips. The 3D grooved roll model reveals the aerodynamic functionality of the grooved roll. With the optimal groove size it is possible to avoid closing nip overpressure and keep the web attached to the fabric surface in the area of the wrap angle. The groove flow friction and minor losses play a different role when the wrap angle is changed. The proposed 2D grooved roll simulation tool is able to replicate the grooved aerodynamic behavior with reasonable accuracy. A small wrap angle predicts the pressure distribution correctly with the chosen approach for calculating the groove friction losses. With a large wrap angle, the groove friction loss shows too large pressure gradients, and the way of calculating the air flow friction losses in the groove has to be reconsidered. The aerodynamic functionality of the grooved roll is based on minor and viscous losses in the closing and opening nips as well as in the grooves. The proposed 2D grooved roll model is a simplification in order to reduce computational and modeling efforts. The simulation tool makes it possible to simulate complex paper machine constructions in the paper machine scale. In order to use the grooved roll as a replacement for the vacuum roll, the grooved roll properties have to be considered on the basis of the web handling application.

Training system for conceptual design and evaluation for wastewater treatment

Rising population, rapid urbanisation and growing industrialisation have severely stressed water quality and its availability in Malawi. In addition, financial and institutional problems and the expanding agro industry have aggravated this problem. The situation is worsened by depleting water resources and pollution from untreated sewage and industrial effluent. The increasing scarcity of clean water calls for the need for appropriate management of available water resources. There is also demand for a training system for conceptual design and evaluation for wastewater treatment in order to build the capacity for technical service providers and environmental practitioners in the country. It is predicted that Malawi will face a water stress situation by 2025. In the city of Blantyre, this situation is aggravated by the serious pollution threat from the grossly inadequate sewage treatment capacity. This capacity is only 23.5% of the wastewater being generated presently. In addition, limited or non-existent industrial effluent treatment has contributed to the severe water quality degradation. This situation poses a threat to the ecologically fragile and sensitive receiving water courses within the city. This water is used for domestic purposes further downstream. This manuscript outlines the legal and policy framework for wastewater treatment in Malawi. The manuscript also evaluates the existing wastewater treatment systems in Blantyre. This evaluation aims at determining if the effluent levels at the municipal plants conform to existing standards and guidelines and other associated policy and regulatory frameworks. The raw material at all the three municipal plants is sewage. The typical wastewater parameters are Biochemical Oxygen Demand (BOD5), Chemical Oxygen Demand (COD), and Total Suspended Solids (TSS). The treatment target is BOD5, COD, and TSS reduction. Typical wastewater parameters at the wastewater treatment plant at MDW&S textile and garments factory are BOD5 and COD. The treatment target is to reduce BOD5 and COD. The manuscript further evaluates a design approach of the three municipal wastewater treatment plants in the city and the wastewater treatment plant at Mapeto David Whitehead & Sons (MDW&S) textile and garments factory. This evaluation utilises case-based design and case-based reasoning principles in the ED-WAVE tool to determine if there is potential for the tool in Blantyre. The manuscript finally evaluates the technology selection process for appropriate wastewater treatment systems for the city of Blantyre. The criteria for selection of appropriate wastewater treatment systems are discussed. Decision support tools and the decision tree making process for technology selection are also discussed. Based on the treatment targets and design criteria at the eight cases evaluated in this manuscript in reference to similar cases in the ED-WAVE tool, this work confirms the practical use of case-based design and case-based reasoning principles in the ED-WAVE tool in the design and evaluation of wastewater treatment 6 systems in sub-Sahara Africa, using Blantyre, Malawi, as the case study area. After encountering a new situation, already collected decision scenarios (cases) are invoked and modified in order to arrive at a particular design alternative. What is necessary, however, is to appropriately modify the case arrived at through the Case Study Manager in order to come up with a design appropriate to the local situation taking into account technical, socio-economic and environmental aspects. This work provides a training system for conceptual design and evaluation for wastewater treatment.

Structure-related magnetic fabric studies : implications for deformed and undeformed Precambrian rocks

The aim of this thesis research was to gain a better understanding of the emplacement of rapakivi granite intrusions, as well as the emplacement of gold-bearing hydrothermal fluids in structurally controlled mineralizations. Based on investigations of the magnetic fabric, the internal structures could be analysed and the intrusion mechanisms for rapakivi granite intrusions and respectively different deformation stages within gold-bearing shear and fault zones identified. Aeromagnetic images revealed circular structures within the rapakivi granite batholiths of Wiborg, Vehmaa and Åland. These circular structures represent intrusions that eventually build up these large batholiths. The rapakivi granite intrusions of Vehmaa, Ruotsinpyhtää within the Wiborg batholith and Saltvik intrusions within the Åland batholith all show bimodal magnetic susceptibilities with paramagnetic and ferromagnetic components. The distribution of the bimodality is related to different magma batches of the studied intrusions. The anisotropy of magnetic susceptibility (AMS) reveals internal structures that cannot be studied macroscopically or by microscope. The Ruotsinpyhtää and Vehmaa intrusions represent similar intrusion geometries, with gently to moderately outward dipping magnetic foliations. In the case of Vehmaa, the magnetic lineations are gently plunging and trend in the directions of the slightly elongated intrusion. The magnetic lineations represent magma flow. The shapes of the AMS ellipsoids are also more planar (oblate) in the central part of the intrusion, whereas they become more linear (prolate) near the margin. These AMS results, together with field observations, indicate that the main intrusion mechanism has involved the subsidence of older blocks with successive intrusion of fractionated magma during repeated cauldron subsidence. The Saltvik area within the Åland batholith consists of a number of smaller elliptical intrusions of different rapakivi types forming a multiple intrusive complex. The magnetic fabric shows a general westward dipping of the pyterlite and eastward dipping of the contiguous even-grained rapakivi granite, which indicates a central inflow of magma batches towards the east and west resulting from a laccolitic emplacement of magma batches, while the main mechanism for space creation was derived from subsidence. The magnetic fabric of structurally controlled gold potential shear and fault zones in Jokisivu, Satulinmäki and Koijärvi was investigated in order to describe the internal structures and define the deformation history and emplacement of hydrothermal fluids. A further aim of the research was to combine AMS studies with palaeomagnetic methods to constrain the timing for the shearing event relative to the precipitation of ferromagnetic minerals and gold. All of the studied formations are dominated by monoclinic pyrrhotite. The AMS directions generally follow the tectonic structures within the formations. However, internal variations in the AMS direction as well as the shapes of the AMS ellipsoids are observed within the shear zones. In Jokisivu and Satulinmäki in particular, the magnetic signatures of the shear zone core differ from the margins. Furthermore, the shape of the magnetic fabric in the shear zone core of Jokisivu is dominated by oblate shapes, whereas the margins exhibit prolate shapes. These variations indicate a later effect of the hydrothermal fluids on the general shear event. The palaeo-magnetic results reveal a deflection from the original Svecofennian age geomagnetic direction. These results, coupled with correlations between the orientation of the NRM vectors and the magnetic and rock fabrics, imply that the gold-rich hydrothermal fluids were emplaced pre/syntectonically during the late stages of the Svecofennian orogeny.

e-Business and collaboration: A case study of pulp supply chain

This thesis studies how the case company could digitalize its supply chain and what kind of advantages this would create in the light of supply chain efficiency. The case company manufactures several pulp products that are used for paper, fabrics and packaging products by customers worldwide. The paper and pulp industry has been paying more and more attention to increasing supply chain efficiency with new operating and service models made possible by today’s information technology. The main focus of this study is on the supply chain between the case company and its key customers and the goal is to find ways to make the operations between them as efficient as possible. The study relays heavily on collaboration techniques and digitalization technologies. In addition to a theoretical framework, the study includes several empirical studies that offer real-life examples of how these theories and technologies are applied in operating environments similar to the case company. A plan with strategic and operational levels is created according to the findings of the previous sections to support the case company’s future operations. The plan is based on an RFID-supported collaboration model that aims to advance information sharing between the supply chain partners. The time for an RFID-investment is sought to be very optimal and the benefits of such system to be noteworthy, but challenging to measure in monetary terms.

Stability and properties of cellulose-sodium hydroxide solution systems

Since cellulose is a linear macromolecule it can be used as a material for regenerated cellulose fiber products e.g. in textile fibers or film manufacturing. Cellulose is not thermoformable, thus the manufacturing of these regenerated fibers is mainly possible through dissolution processes preceding the regeneration process. However, the dissolution of cellulose in common solvents is hindered due to inter- and intra-molecular hydrogen bonds in the cellulose chains, and relatively high crystallinity. Interestingly at subzero temperatures relatively dilute sodium hydroxide solutions can be used to dissolve cellulose to a certain extent. The objective of this work was to investigate the possible factors that govern the solubility of cellulose in aqueous NaOH and the solution stability. Cellulose-NaOH solutions have the tendency to form a gel over time and at elevated temperature, which creates challenges for further processing. The main target of this work was to achieve high solubility of cellulose in aqueous NaOH without excessively compromising the solution stability. In the literature survey an overview of the cellulose dissolution is given and possible factors contributing to the solubility and solution properties of cellulose in aqueous NaOH are reviewed. Furthermore, the concept of solution rheology is discussed. In the experimental part the focus was on the characterization of the used materials and properties of the prepared solutions mainly concentrating on cellulose solubility and solution stability.