Extraction of polymeric galactoglucomannans from spruce wood by pressurized hot water

The major type of non-cellulosic polysaccharides (hemicelluloses) in softwoods, the partly acetylated galactoglucomannans (GGMs), which comprise about 15% of spruce wood, have attracted growing interest because of their potential to become high-value products with applications in many areas. The main objective of this work was to explore the possibilities to extract galactoglucomannans in native, polymeric form in high yield from spruce wood with pressurised hot-water, and to obtain a deeper understanding of the process chemistry involved. Spruce (Picea abies) chips and ground wood particles were extracted using an accelerated solvent extractor (ASE) in the temperature range 160 – 180°C. Detailed chemical analyses were done on both the water extracts and the wood residues. As much as 80 – 90% of the GGMs in spruce wood, i.e. about 13% based on the original wood, could be extracted from ground spruce wood with pure water at 170 – 180°C with an extraction time of 60 min. GGMs comprised about 75% of the extracted carbohydrates and about 60% of the total dissolved solids. Other substances in the water extracts were xylans, arabinogalactans, pectins, lignin and acetic acid. The yields from chips were only about 60% of that from ground wood. Both the GGMs and other non-cellulosic polysaccharides were extensively hydrolysed at severe extraction conditions when pH dropped to the level of 3.5. Addition of sodium bicarbonate increased the yields of polymeric GGMs at low additions, 2.5 – 5 mM, where the end pH remained around 3.9. However, at higher addition levels the yields decreased, mainly because the acetyl groups in GGMs were split off, leading to a low solubility of GGMs. Extraction with buffered water in the pH range 3.8 – 4.4 gave similar yields as with plain water, but gave a higher yield of polymeric GGMs. Moreover, at these pH levels the hydrolysis of acetyl groups in GGMs was significantly inhibited. It was concluded that hot-water extraction of polymeric GGMs in good yields (up to 8% of wood) demands appropriate control of pH, in a narrow range about 4. These results were supported by a study of hydrolysis of GGM at constant pH in the range of 3.8 – 4.2 where a kinetic model for degradation of GGM was developed. The influence of wood particle size on hot-water extraction was studied with particles in the range of 0.1 – 2 mm. The smallest particles (< 0.1 mm) gave 20 – 40% higher total yield than the coarsest particles (1.25 – 2 mm). The difference was greatest at short extraction times. The results indicated that extraction of GGMs and other polysaccharides is limited mainly by the mass transfer in the fibre wall, and for coarse wood particles also in the wood matrix. Spruce sapwood, heartwood and thermomechnical pulp were also compared, but only small differences in yields and composition of extracts were found. Two methods for isolation and purification of polymeric GGMs, i.e. membrane filtration and precipitation in ethanol-water, were compared. Filtration through a series of membranes with different pore sizes separated GGMs of different molar masses, from polymers to oligomers. Polysaccharides with molar mass higher than 4 kDa were precipitated in ethanol-water. GGMs comprised about 80% of the precipitated polysaccharides. Other polysaccharides were mainly arabinoglucuronoxylans and pectins. The ethanol-precipitated GGMs were by 13C NMR spectroscopy verified to be very similar to GGMs extracted from spruce wood in low yield at a much lower temperature, 90°C. The obtained large body of experimental data could be utilised for further kinetic and economic calculations to optimise technical hot-water extractionof softwoods.

Lysine supplementation of barley wet distillers' solids diets for growing-finishing pigs

Selostus: Rankkivalkuaisdieetin lysiinitäydennyksen vaikutus sikojen tuotantotuloksiin

Export of dissolved organic carbon, nitrogen and phosphorus following clear-cutting of three Norway spruce forest growing on drained peatlands in southern Finland

Abstract

Rheology of high solids surface size starches

Tämän diplomityön tarkoituksena oli tutkia pintaliimatärkkelysten reologista käyttäytymistä korkeissa kuiva-ainepitoisuuksissa. Tarve työn suorittamiselle syntyi kun tutkittiin pintaliimausta filminsiirtopuristimella tavallista korkeammissa kuiva-ainepitoisuuksissa, sileän sauvan ollessa applikointilaitteena. Koska applikointi sileällä sauvalla tapahtuu hydrodynaamisten periaatteiden mukaisesti, sen käyttö edellyttää pintaliimojen reologisten ominaisuuksien tarkkaa tuntemusta ja hallintaa.Kiinnostuksen kohteena olevat ominaisuudet olivat tärkkelysten kuiva-ainepitoisuuden (8 – 30 %) vaikutus viskositeettiin eri lämpötiloissa (20, 30, 40 ja 50 ºC), leikkausnopeus alueella 1 s-1 - 700 000 s-1. Myös tärkkelysten myötörajat määritettiin tutkimuksessa. Viskositeetti eri leikkausnopeusalueilla mitattiin seuraavilla laitteilla: Bohlin VOR (matalat leikkausnopeudet ja myötöraja) ja Hercules HiShear (keskitason leikkausnopeudet) reometrit sekä Eklund kapillaariviskometri (korkeat leikkausno-peudet). Analysoidut tärkkelykset olivat kaksi anionista matalaviskoottista peruna (tärkkelys A) ja ohra (tärkkelys C) tärkkelystä, sekä yksi kationinen korkeaviskoottinen peruna tärkkelys (tärkkelys B). Tutkittujen tärkkelysten Brookfield viskositeetit (100 rpm) olivat (10 % liuos, 60 °C:ssa) tärkkelys A ja C: 25 ± 5 mPas ja tärkkelys B: 100 ± 20 mPas.Tärkkelysliuosten kuiva-ainepitoisuuden noustessa muuttui virtauskäyttäytyminen Newtoniaalisesta leikkausohenevaksi. Leikkausoheneva käyttäytyminen oli voimakkainta tärkkelys B:n kohdalla. Viskositeetti – lämpötila riippuvuus korkeissa leikkausnopeuksissa (esim. 500 000 s-1) oli vähäisempää, mitä oli oletettavissa Brookfield viskositeettiarvojen perusteella. Kaikki tarkkelykset osoittautuivat tiksotrooppisiksi, myös tiksotrooppisuus lisääntyi kuiva-ainepitoisuuden kasvaessa. Tärkkelysten myötörajat osoittautuivat odottamattoman alhaisiksi, kuitenkin varsinkin tärkkelys B:n myötörajat olivat selvästi riippuvaisia lämpötilasta ja kuiva-ainepitoisuudesta. Tutkittujen tärkkelysten virtauskäyttäytyminen oli kirjallisuudessa esitetyn kaltaista. Tärkkelysmolekyylien ketjun pituus oli tärkein tärkkelyksen reologisia ominaisuuksia määrittävä tekijä; mitä matalampi on tärkkelyksen molekyylimassa, sitä matalammat ovat viskositeetti ja myötöraja. Pintaliimauksessa tärkkelysmolekyylien ketjunpituudella on suuri vaikutus ajettavuuteen ja lopputuotteen ominaisuuksiin. Haasteellista pintaliimatärkkelyksen valinnassa on sellaisen yhdistelmän löytäminen, jossa sopivan reologisen käyttäytymisen omaava tärkkelys ja pintaliimatulle paperille tai kartongille asetetut vaatimukset kohtaavat.

Flokkulaation seuraaminen partikkelikokoanalysaattorilla

Tässä työssä tutkittiin kahden erilaisen partikkelikokoanalysaattorin, PSyA:n ja PIA:n soveltuvuutta flokkuloinnin online-seurantaan. Kummallekin menetelmälle määritettiin raja-arvot, kuten lietteen maksimisakeus. Lisäksi tutkittiin flokkulanttiannostuksen, sekoitusnopeuden, sekoitusajan ja lietteen kiintoainepitoisuuden vaikutusta flokkikokojakaumaan. Kirjallisuusosassa tarkasteltiin kolloidisen suspension ominaispiirteitä, koaguloinnin ja flokkuloinnin teoriaa, flokkulaation kokeellista tutkimista sekä prosessin jatkuvatoimiseen seurantaan soveltuvia laitteita. Lisäksi esitettiin taustaa hydrometallurgisesta prosessista, johon työ liittyy. Flokkauskokeissa käytettiin jätevettä, jonka koostumus vastasi metalliteollisuuden peittausjätevesien tyypillistä koostumusta. Tutkittava jätevesimäärä käsiteltiin ensin kalkkimaidolla, jonka jälkeen saostunut kiintoaine flokattiin synteettisellä polymeeriflokkulantilla. Lietteen keskimääräinen kiintoainepitoisuus oli n. 10 g/l. Esikokeiden perusteella PSyA:lla voitiin mitata ilman laimennusta, mutta PIA:lla tuloksia ei saatu ilman laimentamista kiintoainepitoisuuteen n. 2,5 g/l. Kokeiden aikana havaittiin, että flokit muodostuivat erittäin nopeasti. Flokkien hajoaminen alkoi pian sen jälkeen, kun flokkulantin annostelu lopetettiin. Sekoitusnopeudella 40 r/min tai alle flokit alkoivat laskeutua astian pohjalle sekoituksesta huolimatta ja ne pysyivät pitempään koossa kuin suuremmilla sekoitusnopeuksilla. 5 - 10 minuutin kuluttua flokkulantin lisäämisestä saavutettiin tasapaino, jolloin flokkien kokojakauma ei enää muuttunut. Sekoitusnopeuksilla 80 r/min ja 120 r/min tasapainotilanteen koko-jakauma oli selvästi kapeampi kuin pienimmällä sekoitusnopeudella. Alkuperäisessä lietteessä flokit olivat suurempia kuin laimennetussa lietteessä. PSyA:lla jännepituusjakaumien määrittäminen oli varsin hidasta prosessissa tapahtuviin muutoksiin verrattuna, ja tuloksissa oli suurta hajontaa. PIA:lla saadut partikkelikokojakaumat sitä vastoin olivat johdonmukaisempia, vaikka suurimpien flokkien määrittäminen osoittautuikin epämääräiseksi. Menetelmän suurimmaksi puutteeksi todettiin soveltumattomuus sakeiden lietteiden analysointiin. Kumpikaan menetelmä ei ilman modifiointia sovellu tutkitun lietteen kaltaisten prosessilietteiden flokkuloinnin seurantaan.

Kunnostusojituksen vaikutus kiintoaine- ja ravinnehuuhtoumiin ojitetuilta soilta

Seloste artikkelista: Nieminen, M., Ahti, E., Koivusalo, H., Mattson, T., Sarkkola, S. & Laurén, A. / Export of suspended solids and dissolved elements from peatland areas after ditch network maintenance in south-central Finland. Silva Fennica 44 (2010) : 1, 39-49.

Käytetyn voiteluöljyn regenerointilaitoksen prosessivesien karakterisointi

Käytetyn voiteluöljyn regeneroinnissa muodostuu prosessivettä useista lähteistä. Tehokas päästöjenhallinta on yksi tärkeimmistä tavoitteista regenerointilaitoksen operoinnissa ja sen takia sitä tulee kehittää jatkuvasti entistä paremmaksi. Tavoitteisiin pääsemiseksi on oleellista tunnistaa vesienkäsittelyprosessin laadullinen massatase ja laadunvaihtelut ajotilanteiden mukaan. Työssä tutkitaan ja analysoidaan veden sisältämiä epäpuhtauksia sekä kirjallisuuslähteiden perusteella, että standardimenetelmillä ja modifioiduilla menetelmillä, joilla on akkreditointi. Analyysituloksista muodostetaan laadullinen massatase, josta nähdään epäpuhtauksien ja niitä kuvaavien parametrien kuormitukset kussakin prosessivesivirrassa. Tulosten perusteella arvioidaan nykyisen vesienkäsittelyn tehokkuutta, sen säätömahdollisuuksia ja kehitystarvetta. Tarkastelun ulkopuolelle kuitenkin jätetään vesienkäsittelystä ulosjohdettavan prosessiveden puhdistuslaitos. Tutkimusten perusteella regenerointilaitoksessa muodostuvien prosessivesien epäpuhtaudet koostuvat öljystä, BTEX-yhdisteistä, fenoliyhdisteistä, liuottimista, polttoaineiden ja voiteluöljyjen lisäaineista, typpi- ja rikkiyhdisteistä, metalliyhdisteistä sekä kiintoaineesta. Öljy jakautuu kevyisiin (C5-C10), keskiraskaisiin (C10-21) ja raskaisiin (C21-40) jakeisiin. Vesienkäsittelyssä suurin osa öljystä ja epäpuhtauksista saadaan erottumaan vedestä, jolloin puhdistuslaitokselle päätyy jäämäpitoisuudet öljyä, haihtuvia yhdisteitä sekä muita epäpuhtauksia. Puhdistuslaitosta kuormittavat eniten liuenneet orgaaniset yhdisteet sekä korkeaa kemiallista hapenkulutusta aiheuttavat epäorgaaniset yhdisteet (suolat), joiden erottamista prosessivesistä on syytä tulevaisuudessa kehittää.

Solids removal in pyrolysis

Pyrolysis is a process for turning biomass into liquid fuel. The process consists of heating the biomass in inert conditions and quenching the resulting vapors into oil. The oil has many potential uses, such as heating fuel in peak heating plants. In order to broaden the application base and improve the quality of the oil, solids removal has to be addressed. The solids may also increase the probability of plugging in downstream equipment. The purpose of this research was to gain an understanding of the formation of solids in the pyrolysis process and to assess options for reducing the solid content of the oil. From literature it is known that the solids can be removed either by hot vapor filtration, liquid treatment or multiple cyclones. Hot vapor filtration decreases yield, but improves the stability of the oil while simultaneously removing solids and ash. Liquid treatment techniques are good for removing large particles but involve losses of pyrolysis liquid. Cyclones are a traditional robust technique used regularly in pyrolysis. In the experimental part of this thesis, a 2 MWfuel pyrolysis setup with 2 cyclones in series was operated and monitored. Solid and liquid samples were collected from various parts of the process for further examination. Sampling and sample treatment techniques were developed. The chemical properties of the pyrolysis char were also analyzed and assessed as a function of reactor temperature and fluidizing velocity. By measuring the particle size distributions it was noticed that there were much smaller particles collected from the second cyclone than fed into pyrolysis. The solids in the pyrolysis oil were even smaller. This was most likely caused by attrition and shrinkage. Due to better separation efficiency of the cyclones in large particles, excess attrition should be avoided.

Käänteisosmoosin esikäsittelymenetelmät

Käänteisosmoosisuodatusta käytetään erityisesti teollisuuden jätevesien loppupuhdistuksessa. Suodatuksen ongelmana on kalvojen likaantuminen ja tukkiutuminen. Tässä työssä on aiempia tutkimuksia hyväksikäyttäen tutkittu käänteisosmoosiin tulevan veden esikäsittelemistä niin, että kalvojen likaantumiselta vältyttäisiin. Menetelmien vertailussa on käytetty erilaisia veden laadusta kertovia parametreja. Ongelmallisimmiksi aineksiksi huomattiin orgaaninen aines ja jotkin veteen liuenneet ionit. Kiintoaineen erottaminen ei ole ollut suuri ongelma, sillä sen saa poistettua tavallisesti käytetyillä rakeissuodatuksella, laskeutuksella, flotaatiolla ja kalvosuodatuksella. Orgaanista ainesta on saatu erotettua erityisesti hapettamalla, aktiivilieteprosessilla ja biologisella aktiivihiilisuodattimella. Mikro- ja ultrasuodatusta käytetään usein juuri ennen käänteisosmoosia poistamaan erityisesti kolloidista materiaalia ja joitain liuenneita ioneja. Flokkien muodostaminen koagulaatiossa ja flokkulaatiossa parantaa lähes kaikkien menetelmien toimivuutta selvästi. Veden puhdistuksessa käytetyt kemikaalit voivat myös liika-annosteltuina liata kalvoja. Vesien pitoisuuksissa eri ainesten osalta on huomattavia eroja, joten puhdistettava vesi on hyvä analysoida etukäteen parhaiden käsittelymenetelmien valitsemiseksi.

Utilization of steelmaking waste materials for production of calcium carbonate (CaCO3)

The steel industry produces, besides steel, also solid mineral by-products or slags, while it emits large quantities of carbon dioxide (CO2). Slags consist of various silicates and oxides which are formed in chemical reactions between the iron ore and the fluxing agents during the high temperature processing at the steel plant. Currently, these materials are recycled in the ironmaking processes, used as aggregates in construction, or landfilled as waste. The utilization rate of the steel slags can be increased by selectively extracting components from the mineral matrix. As an example, aqueous solutions of ammonium salts such as ammonium acetate, chloride and nitrate extract calcium quite selectively already at ambient temperature and pressure conditions. After the residual solids have been separated from the solution, calcium carbonate can be precipitated by feeding a CO2 flow through the solution. Precipitated calcium carbonate (PCC) is used in different applications as a filler material. Its largest consumer is the papermaking industry, which utilizes PCC because it enhances the optical properties of paper at a relatively low cost. Traditionally, PCC is manufactured from limestone, which is first calcined to calcium oxide, then slaked with water to calcium hydroxide and finally carbonated to PCC. This process emits large amounts of CO2, mainly because of the energy-intensive calcination step. This thesis presents research work on the scale-up of the above-mentioned ammonium salt based calcium extraction and carbonation method, named Slag2PCC. Extending the scope of the earlier studies, it is now shown that the parameters which mainly affect the calcium utilization efficiency are the solid-to-liquid ratio of steel slag and the ammonium salt solvent solution during extraction, the mean diameter of the slag particles, and the slag composition, especially the fractions of total calcium, silicon, vanadium and iron as well as the fraction of free calcium oxide. Regarding extraction kinetics, slag particle size, solid-to-liquid ratio and molar concentration of the solvent solution have the largest effect on the reaction rate. Solvent solution concentrations above 1 mol/L NH4Cl cause leaching of other elements besides calcium. Some of these such as iron and manganese result in solution coloring, which can be disadvantageous for the quality of the PCC product. Based on chemical composition analysis of the produced PCC samples, however, the product quality is mainly similar as in commercial products. Increasing the novelty of the work, other important parameters related to assessment of the PCC quality, such as particle size distribution and crystal morphology are studied as well. As in traditional PCC precipitation process, the ratio of calcium and carbonate ions controls the particle shape; a higher value for [Ca2+]/[CO32-] prefers precipitation of calcite polymorph, while vaterite forms when carbon species are present in excess. The third main polymorph, aragonite, is only formed at elevated temperatures, above 40-50 °C. In general, longer precipitation times cause transformation of vaterite to calcite or aragonite, but also result in particle agglomeration. The chemical equilibrium of ammonium and calcium ions and dissolved ammonia controlling the solution pH affects the particle sizes, too. Initial pH of 12-13 during the carbonation favors nonagglomerated particles with a diameter of 1 μm and smaller, while pH values of 9-10 generate more agglomerates of 10-20 μm. As a part of the research work, these findings are implemented in demonstrationscale experimental process setups. For the first time, the Slag2PCC technology is tested in scale of ~70 liters instead of laboratory scale only. Additionally, design of a setup of several hundreds of liters is discussed. For these purposes various process units such as inclined settlers and filters for solids separation, pumps and stirrers for material transfer and mixing as well as gas feeding equipment are dimensioned and developed. Overall emissions reduction of the current industrial processes and good product quality as the main targets, based on the performed partial life cycle assessment (LCA), it is most beneficial to utilize low concentration ammonium salt solutions for the Slag2PCC process. In this manner the post-treatment of the products does not require extensive use of washing and drying equipment, otherwise increasing the CO2 emissions of the process. The low solvent concentration Slag2PCC process causes negative CO2 emissions; thus, it can be seen as a carbon capture and utilization (CCU) method, which actually reduces the anthropogenic CO2 emissions compared to the alternative of not using the technology. Even if the amount of steel slag is too small for any substantial mitigation of global warming, the process can have both financial and environmental significance for individual steel manufacturers as a means to reduce the amounts of emitted CO2 and landfilled steel slag. Alternatively, it is possible to introduce the carbon dioxide directly into the mixture of steel slag and ammonium salt solution. The process would generate a 60-75% pure calcium carbonate mixture, the remaining 25-40% consisting of the residual steel slag. This calcium-rich material could be re-used in ironmaking as a fluxing agent instead of natural limestone. Even though this process option would require less process equipment compared to the Slag2PCC process, it still needs further studies regarding the practical usefulness of the products. Nevertheless, compared to several other CO2 emission reduction methods studied around the world, the within this thesis developed and studied processes have the advantage of existing markets for the produced materials, thus giving also a financial incentive for applying the technology in practice.

Behavior of black liquor nitrogen in combustion : formation of cyanate

The Kraft pulping process is the dominant chemical pulping process in the world. Roughly 195 million metric tons of black liquor are produced annually as a by-product from the Kraft pulping process. Black liquor consists of spent cooking chemicals and dissolved organics from the wood and can contain up to 0.15 wt% nitrogen on dry solids basis. The cooking chemicals from black liquor are recovered in a chemical recovery cycle. Water is evaporated in the first stage of the chemical recovery cycle, so the black liquor has a dry solids content of 65-85% prior to combustion. During combustion of black liquor, a portion of the black liquor nitrogen is volatilized, finally forming N2 or NO. The rest of the nitrogen remains in the char as char nitrogen. During char conversion, fixed carbon is burned off leaving the pulping chemicals as smelt, and the char nitrogen forms mostly smelt nitrogen (cyanate, OCN-). Smelt exits the recovery boiler and is dissolved in water. The cyanate from smelt decomposes in the presence of water, forming NH3, which causes nitrogen emissions from the rest of the chemical recovery cycle. This thesis had two focuses: firstly, to determine how the nitrogen chemistry in the recovery boiler is affected by modification of black liquor; and secondly, to find out what causes cyanate formation during thermal conversion, and which parameters affect cyanate formation and decomposition during thermal conversion of black liquor. The fate of added biosludge nitrogen in chemical recovery was determined in Paper I. The added biosludge increased the nitrogen content of black liquor. At the pulp mill, the added biosludge did not increase the NO formation in the recovery boiler, but instead increased the amount of cyanate in green liquor. The increased cyanate caused more NH3 formation, which increased the NCG boiler’s NO emissions. Laboratory-scale experiments showed an increase in both NO and cyanate formation after biosludge addition. Black liquor can be modified, for example by addition of a solid biomass to increase the energy density of black liquor, or by separation of lignin from black liquor by precipitation. The precipitated lignin can be utilized in the production of green chemicals or as a fuel. In Papers II and III, laboratory-scale experiments were conducted to determine the impact of black liquor modification on NO and cyanate formation. Removal of lignin from black liquor reduced the nitrogen content of the black liquor. In most cases NO and cyanate formation decreased with increasing lignin removal; the exception was NO formation from lignin lean soda liquors. The addition of biomass to black liquor resulted in a higher nitrogen content fuel mixture, due to the higher nitrogen content of biomass compared to black liquor. More NO and cyanate were formed from the fuel mixtures than from pure black liquor. The increased amount of formed cyanate led to the hypothesis that black liquor is catalytically active and converts a portion of the nitrogen in the mixed fuel to cyanate. The mechanism behind cyanate formation during thermal conversion of black liquor was not clear before this thesis. Paper IV studies the cyanate formation of alkali metal loaded fuels during gasification in a CO2 atmosphere. The salts K2CO3, Na2CO3, and K2SO4 all promoted char nitrogen to cyanate conversion during gasification, while KCl and CaCO3 did not. It is now assumed that cyanate is formed when alkali metal carbonate or an active intermediate of alkali metal carbonate (e.g. -CO2K) reacts with the char nitrogen forming cyanate. By testing different fuels (bark, peat, and coal), each of which had a different form of organic nitrogen, it was concluded that the form of organic nitrogen in char also has an impact on cyanate formation. Cyanate can be formed during pyrolysis of black liquor, but at temperatures 900°C or above, the formed cyanate will decompose. Cyanate formation in gasifying conditions with different levels of CO2 in the atmosphere was also studied. Most of the char nitrogen was converted to cyanate during gasification at 800-900°C in 13-50% CO2 in N2, and only 5% of the initial fuel nitrogen was converted to NO during char conversion. The formed smelt cyanate was stable at 800°C 13% CO2, while it decomposed at 900°C 13% CO2. The cyanate decomposition was faster at higher temperatures and in oxygen-containing atmospheres than in an inert atmosphere. The presence of CO2 in oxygencontaining atmospheres slowed down the decomposition of cyanate. This work will provide new information on how modification of black liquor affects the nitrogen chemistry during thermal conversion of black liquor and what causes cyanate formation during thermal conversion of black liquor. The formation and decomposition of cyanate was studied in order to provide new data, which would be useful in modeling of nitrogen chemistry in the recovery boiler.

Kunnallisen jätevedenkäsittelyn tehostaminen membraanitekniikan avulla – esimerkkinä Savitaipaleen jätevedenpuhdistamo

Työssä tutkittiin mahdollisuutta tehostaa kunnallista jätevedenpuhdistusta membraanitekniikkaa käyttäen. Teoriaosassa perehdyttiin kunnallisen jäteveden omi-naisuuksiin ja perinteiseen puhdistusprosessiin. Tämän lisäksi membraanien yleisiä ominaisuuksia, membraanityyppien kykyä erottaa jäteveden sisältämiä yhdisteitä sekä erilaisia mahdollisuuksia membraanisuodatukselle perinteisen jäteve-denpuhdistusprosessin yhteydessä käytiin läpi. Kokeellisessa osassa keskityttiin Savitaipaleen puhdistamon puhdistetun jäteveden laadun parantamiseen membraanisuodatukseen perustuvalla jälkikäsittely-yksiköllä eli tertiäärisuodatuksella. Erilaisia paineavusteisia membraanitekniikoita (MF, UF, NF ja RO) tutkittiin jäteveden puhdistamiseksi ja erotustehokkuuden vertailemiseksi. Tavoitteena oli löytää tehokas ja käytännössä toimiva tapa poistaa fosforia ja typpeä puhdistetusta jätevedestä. Tasomaisilla membraaneilla tehdyissä suodatuksissa MF-membraanit poistivat tehokkaasti fosforia (97 – 98 %) sekä kiintoainesta (100 %) jätevedestä. RO-membraanit alensivat fosfori- (100 %) ja typpipitoisuutta (90 – 94 %) tehokkaasti, poistaen myös liuenneita orgaanisia yhdisteitä (DOC, 90 – 94 %). Mikrosuodatukseen perustuvilla onttokuitumembraaneilla saavutettiin tehokkaan fosforinpoiston lisäksi tasainen kapasiteetti suodatuksen aikaista puhdistusmene-telmää optimoimalla. Pitoisuusalenemat olivat myös erittäin korkeita fosforille (97 – 99 %), kiintoaineelle (100 %), sameudelle (96 – 99 %) sekä COD:lle (38 – 55 %). Tulosten perusteella membraanitekniikkaan perustuva onttokuitusuodatus olisi tehokas ja toimiva jälkikäsittelyprosessi fosforinpoistoon ja jäteveden laadun pa-rantamiseen. Typen poistamiseen parhaiten toimi RO-membraani.

Intensification of Operation of Inclined Plate Settler at Fertilizer Plant

Fertilizer plant’s process waters contain high concentrations of nitrogen compounds, such as ammonium and nitrate. Phosphorus and fluorine, which originate from phosphoric acid and rock phosphate (apatite) used in fertilizer production, are also present. Phosphorus and nitrogen are the primary nutrients causing eutrophication of surface waters. At fertilizer plant process waters are held in closed internal circulation. In a scrubber system process waters are used for washing exhaust gases from fertilizer reactors and dry gases from granulation drums as well as for cooling down the fertilizer slurry in neutralization reactor. Solids in process waters are separated in an inclined plate settler by gravitational sedimentation. However, the operation of inclined plate settler has been inadequate. The aim of this thesis was to intensify the operation of inclined plate settler and thus the solids separation e.g. through coagulation and/or flocculation process. Chemical precipitation was studied to reduce the amount of dissolved species in process waters. Specific interest was in precipitation of nitrogen, phosphorus, and fluorine containing specimens. Amounts of phosphorus and fluorine were reduced significantly by chemical precipitation. When compared to earlier studies, annual chemical costs were almost eight times lower. Instead, nitrogen compounds are readily dissolved in water, thus being difficult to remove by precipitation. Possible alternative techniques for nitrogen removal are adsorption, ion exchange, and reverse osmosis. Settling velocities of pH adjusted and flocculated process waters were sufficient for the operation of inclined plate settler. Design principles of inclined plate settler are also presented. In continuation studies, flow conditions in inclined plate settler should be modelled with computational fluid dynamics and suitability of adsorbents, ion exchange resins, and membranes should be studied in laboratory scale tests.