A System-Level Simulation Model for a Protocol Processor

As the development of integrated circuit technology continues to follow Moore’s law the complexity of circuits increases exponentially. Traditional hardware description languages such as VHDL and Verilog are no longer powerful enough to cope with this level of complexity and do not provide facilities for hardware/software codesign. Languages such as SystemC are intended to solve these problems by combining the powerful expression of high level programming languages and hardware oriented facilities of hardware description languages. To fully replace older languages in the desing flow of digital systems SystemC should also be synthesizable. The devices required by modern high speed networks often share the same tight constraints for e.g. size, power consumption and price with embedded systems but have also very demanding real time and quality of service requirements that are difficult to satisfy with general purpose processors. Dedicated hardware blocks of an application specific instruction set processor are one way to combine fast processing speed, energy efficiency, flexibility and relatively low time-to-market. Common features can be identified in the network processing domain making it possible to develop specialized but configurable processor architectures. One such architecture is the TACO which is based on transport triggered architecture. The architecture offers a high degree of parallelism and modularity and greatly simplified instruction decoding. For this M.Sc.(Tech) thesis, a simulation environment for the TACO architecture was developed with SystemC 2.2 using an old version written with SystemC 1.0 as a starting point. The environment enables rapid design space exploration by providing facilities for hw/sw codesign and simulation and an extendable library of automatically configured reusable hardware blocks. Other topics that are covered are the differences between SystemC 1.0 and 2.2 from the viewpoint of hardware modeling, and compilation of a SystemC model into synthesizable VHDL with Celoxica Agility SystemC Compiler. A simulation model for a processor for TCP/IP packet validation was designed and tested as a test case for the environment.

Supporting UK Repositories; a Cohesive Strategy

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Designing a Bit Preservation System

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Hajautetun automaation käyttö osana simulaatiota

Työssä perehdytään simulaatiotekniikkaan, jossa käytetään osana fyysistä laitteistoa, ja siihen tarvittaviin komponentteihin, kuten ohjelmistorajapintoihin sekä kenttäväylään. Työssä tutustutaan myös IEC 61131-3 ja IEC 61499 -standardien mukaisiin toimintolohkomalleihin, joita käytetään automaatiossa. Näiden perusteella kehitetään järjestelmä, jonka avulla Simulink-ympäristössä voidaan oman toimintolohkon avulla käyttää taajuusmuuttajaa osana simulaatiota. Tällaisen reaaliaikaisen systeemin eri osien väliseen synkronointiin kiinnitetään myös huomiota. Järjestelmää testataan simulaatiomallilla, jossa syötetään vääntömomenttiohje taajuusmuuttajalle, joka mittaa siihen kytketyn moottorin pyörimisnopeuden. Mallilla voidaan esimerkiksi arvioida kuorman hitausmomentti. Työssä tutustutaan myös taajuusmuuttajien ohjelmallisiin ominaisuuksiin ja niiden perusteella pohditaan esitetyn kaltaisten järjestelmien käyttöä hajautettuna automaatiojärjestelmänä. Kokeellinen työ tehtiin säätö- ja digitaalitekniikan laboratoriossa vuoden 2010 aikana.

Designing Digital Filters for Servo Systems

The aim of this work was to select an appropriate digital filter for a servo application and to filter the noise from the measurement devices. Low pass filter attenuates the high frequency noise beyond the specified cut-off frequency. Digital lowpass filters in both IIR and FIR responses were designed and experimentally compared to understand their characteristics from the corresponding step responses of the system. Kaiser Windowing and Equiripple methods were selected for FIR response, whereas Butterworth, Chebyshev, InverseChebyshev and Elliptic methods were designed for IIR case. Limitations in digital filter design for a servo system were analysed. Especially the dynamic influences of each designed filter on the control stabilityof the electrical servo drive were observed. The criterion for the selection ofparameters in designing digital filters for servo systems was studied. Control system dynamics was given significant importance and the use of FIR and IIR responses in different situations were compared to justify the selection of suitableresponse in each case. The software used in the filter design was MatLab/Simulink® and dSPACE's DSP application. A speed controlled Permanent Magnet Linear synchronous Motor was used in the experimental work.

Methods of Design and Testing of Real Time Systems

Teollusuussovelluksissa vaaditaan nykyisin yhä useammin reaaliaikaista tiedon käsittelyä. Luotettavuus on yksi tärkeimmistä reaaliaikaiseen tiedonkäsittelyyn kykenevän järjestelmän ominaisuuksista. Sen saavuttamiseksi on sekä laitteisto, että ohjelmisto testattava. Tämän työn päätavoitteena on laitteiston testaaminen ja laitteiston testattavuus, koska luotettava laitteistoalusta on perusta tulevaisuuden reaaliaikajärjestelmille. Diplomityössä esitetään digitaaliseen signaalinkäsittelyyn soveltuvan prosessorikortin suunnittelu. Prosessorikortti on tarkoitettu sähkökoneiden ennakoivaa kunnonvalvontaa varten. Uusimmat DFT (Desing for Testability) menetelmät esitellään ja niitä sovelletaan prosessorikortin sunnittelussa yhdessä vanhempien menetelmien kanssa. Kokemukset ja huomiot menetelmien soveltuvuudesta raportoidaan työn lopussa. Työn tavoitteena on kehittää osakomponentti web -pohjaiseen valvontajärjestelmään, jota on kehitetty Sähkötekniikan osastolla Lappeenrannan teknillisellä korkeakoululla.

Test automation of digital mammography device

Testing of a complex software is time consuming. Automated tools are available quite a lot for desktop applications, but for embedded systems a custom-made tool is required Building a complete test framework is a complicated task. Therefore, the test platform was built on top of an already existing tool, CANoe. CANoe is a tool for CAN bus analysis and node simulation. The functionality of CANoe was extended with LabVIEW DLL. The LabVIEW software was used for simulating hardware components of the embedded device As a result of the study, a platform was created where tests could be automated. Of the current test plan, 10 percent were automated and up to 60 percent could be automated with the current functionality.

Factors Affecting Consumer’s Illicit Purchase of Copyrighted Digital Work

Peer-to-Peer (P2P) technology has revolutionized file exchange activities besides enhancing processing power distribution. As such, this technology which is nowadays made freely available to all internet users also imposes a threat as it enables the illegal distribution of copyrighted digital work. P2P technology continuously evolves in a greater pace than copyright legislation, leading to compatibility gaps between the applicability of copyright law and the illicit file sharing and downloading. Such issues give high incentives to consumers to practise piracy using P2P systems with a low perception of risk towards prosecution, leading to substantial losses for copyright owners. This study focuses on developing insights for content owners on consumer behaviour towards piracy in Finland, where quantitative analyses are assessed using a data set based on a survey conducted by the Helsinki Institute for IT. The research approach investigates the significance of three fundamental areas in relation to evaluate consumer behaviour as: environmental-related factors, innovation-related factors and consumer-related. each of these are integrates concepts derived in previous theoretical models such as the technology acceptance model, theory of reasoned action, theory of planned behaviour, the issue-risk-judgement model and the Hunt & Vitell’s model.

Building the ‘Digital’ Library: Routes to Managing our Institutional Digital Learning, Teaching and Research Assets Together

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

ORCIDs in the Wild: Implementing ORCIDs into Research Support and Repository Systems

Panel at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Repository Rant -- Digital Scavenging

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

GIS in Digital Repositories

Workshop at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Theses and Dissertations Digital Library: Ten years of Open Access and Open Archives in Brazil

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Analyses of the usefulness of Software Defined Storage Solutions for Web-based Digital Preservation Applications

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

When Metadata Collides: Lessons on Combining Records from Multiple Repository Systems.

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014