Formation and Control of Trace Metal Emissions in Co-Firing of Biomass, Peat, and Wastes in Fluidised Bed Combustors

Environmentally harmful consequences of fossil fuel utilisation andthe landfilling of wastes have increased the interest among the energy producers to consider the use of alternative fuels like wood fuels and Refuse-Derived Fuels, RDFs. The fluidised bed technology that allows the flexible use of a variety of different fuels is commonly used at small- and medium-sized power plants ofmunicipalities and industry in Finland. Since there is only one mass-burn plantcurrently in operation in the country and no intention to build new ones, the co-firing of pre-processed wastes in fluidised bed boilers has become the most generally applied waste-to-energy concept in Finland. The recently validated EU Directive on Incineration of Wastes aims to mitigate environmentally harmful pollutants of waste incineration and co-incineration of wastes with conventional fuels. Apart from gaseous flue gas pollutants and dust, the emissions of toxic tracemetals are limited. The implementation of the Directive's restrictions in the Finnish legislation is assumed to limit the co-firing of waste fuels, due to the insufficient reduction of the regulated air pollutants in the existing flue gas cleaning devices. Trace metals emission formation and reduction in the ESP, the condensing wet scrubber, the fabric filter, and the humidification reactor were studied, experimentally, in full- and pilot-scale combustors utilising the bubbling fluidised bed technology, and, theoretically, by means of reactor model calculations. The core of the model is a thermodynamic equilibrium analysis. The experiments were carried out with wood chips, sawdust, and peat, and their refuse-derived fuel, RDF, blends. In all, ten different fuels or fuel blends were tested. Relatively high concentrations of trace metals in RDFs compared to the concentrations of these metals in wood fuels increased the trace metal concentrations in the flue gas after the boiler ten- to hundred-folds, when RDF was co-fired with sawdust in a full-scale BFB boiler. In the case of peat, lesser increase in trace metal concentrations was observed, due to the higher initial trace metal concentrations of peat compared to sawdust. Despite the high removal rate of most of the trace metals in the ESP, the Directive emission limits for trace metals were exceeded in each of the RDF co-firing tests. The dominat trace metals in fluegas after the ESP were Cu, Pb and Mn. In the condensing wet scrubber, the flue gas trace metal emissions were reduced below the Directive emission limits, whenRDF pellet was used as a co-firing fuel together with sawdust and peat. High chlorine content of the RDFs enhanced the mercuric chloride formation and hence the mercury removal in the ESP and scrubber. Mercury emissions were lower than theDirective emission limit for total Hg, 0.05 mg/Nm3, in all full-scale co-firingtests already in the flue gas after the ESP. The pilot-scale experiments with aBFB combustor equipped with a fabric filter revealed that the fabric filter alone is able to reduce the trace metal concentrations, including mercury, in the flue gas during the RDF co-firing approximately to the same level as they are during the wood chip firing. Lower trace metal emissions than the Directive limits were easily reached even with a 40% thermal share of RDF co-firing with sawdust.Enrichment of trace metals in the submicron fly ash particle fraction because of RDF co-firing was not observed in the test runs where sawdust was used as the main fuel. The combustion of RDF pellets with peat caused an enrichment of As, Cd, Co, Pb, Sb, and V in the submicron particle mode. Accumulation and release oftrace metals in the bed material was examined by means of a bed material analysis, mass balance calculations and a reactor model. Lead, zinc and copper were found to have a tendency to be accumulated in the bed material but also to have a tendency to be released from the bed material into the combustion gases, if the combustion conditions were changed. The concentration of the trace metal in the combustion gases of the bubbling fluidised bed boiler was found to be a summary of trace metal fluxes from three main sources. They were (1) the trace metal flux from the burning fuel particle (2) the trace metal flux from the ash in the bed, and (3) the trace metal flux from the active alkali metal layer on the sand (and ash) particles in the bed. The amount of chlorine in the system, the combustion temperature, the fuel ash composition and the saturation state of the bed material in regard to trace metals were discovered to be key factors affecting therelease process. During the co-firing of waste fuels with variable amounts of e.g. ash and chlorine, it is extremely important to consider the possible ongoingaccumulation and/or release of the trace metals in the bed, when determining the flue gas trace metal emissions. If the state of the combustion process in regard to trace metals accumulation and/or release in the bed material is not known,it may happen that emissions from the bed material rather than the combustion of the fuel in question are measured and reported.

Research of wood fuel market in Ukraine and the Republic of Belarus

The goal of the present work was to describe the wood fuel market of Ukraine and the Republic of Belarus, to estimate wood fuel potential and to research opportunities of wood fuel trading. Nowadays the wood waste, wood residues and by-products are becoming more and more potential raw materials for energy production. Against the background of unstable prices of traditional energy sources and environmental degradation, European States are planning to get 12% of energy from alternative sources already in 2010. Wastes of wood-working and agricultural productions are such sources. At present time the most popular wood biofuels are wood pellets, briquettes, wood chips and logs. Ukraine and the Republic of Belarus have a rather big potential of wood fuel resources. But wood fuels markets of these countries are on the entry level and quite disorganized. There is almost no domestic usage of wood biofuel. All produced pellets, briquettes as well as wood chips and logs go to the export, but the volumes are not high at present time. Ukraine and the Republic of Belarus have a very suitable geographical location. The most promising directions of wood fuel trading are developed wood fuel markets of Northern countries, Austria, Germany as well as actively developing markets of Poland and Hungary. At the long distance truck and sea transportation are the most appropriate. At a short distance cheap transportation by rail is more suitable. Thereby export is a potential opportunity for development of wood fuel production and in the future for usage in the researched countries.

Iran's domestic and foreign policies

Iran has a reputation of being a problematic country. Right now, it is proceeding with its nuclear program despite the opposition of the West and neighboring countries and the massive sanctions inflicted upon it. The country is also struggling with domestic issues. Half of Iran’s population belongs to different ethnic or religious minorities. They have poor rights to express their culture in the country, which is a cause of dissatisfaction among non-Shiite and non-Persian citizens. After the Arab Spring, the situation in Iran is getting more topical than ever. In the Syrian conflict, the Shiite Iran is constantly giving support to al-Assad’s regime. These are all factors that have aggravated the already irritated relations between Iran and the West.

Decentralized management of organic household wastes in the Kathmandu Valley using small-scale composting reactors

The sustainable management of municipal solid waste in the Kathmandu Valley has always been a challenging task. Solid waste generation has gone rapidly high in the Kathmandu Valley over the last decade due to booming population and rapid urbaniza-tion. Finding appropriate landfill sites for the disposal of solid wastes generated from the households of the Kathmandu Valley has always been a major problem for Nepalese government. 65 % of total generated wastes from the households of Nepal consist of organic materials. As large fractions of generated household wastes are organic in na-ture, composting can be considered as one of the best sustainable ways to recycle organ-ic wastes generated from the households of Nepal. Model Community Society Development (MCDS), a non-governmental organization of Nepal carried out its small-scale project in five households of the Kathmandu Valley by installing composting reactors. This thesis is based on this small-scale project and has used secondary data provided by MCDS Nepal for carrying out the study. Proper man-agement of organic wastes can be done at household levels through the use of compost-ing reactors. The end product compost can be used as soil conditioners for agricultural purposes such as organic farming, roof-top farming and gardening. The overall average organic waste generation in the Kathmandu Valley is found to be 0,23 kg/person/day and the total amount of organic household wastes generated in the Kathmandu Valley is around 210 Gg/yr. Produced composts from five composting reac-tors contain high amount of moistures but have sufficient amount of nutrients required for the fertility of land and plant growth. Installation of five composting reactors in five households have prevented 2,74 Mg of organic wastes going into the landfills, thus re-ducing 107 kg of methane emissions which is equivalent to 2,7 Mg of carbondioxide.

Teollinen symbioosi - kansallisen ohjelman toteuttaminen Suomessa Britanniaan verrattuna

This master thesis examines the possibility of implementing a national industrial symbiosis programme in Finland. Industrial symbiosis is a close cooperation between companies in which the actors make use of each other's wastes and by-products as raw materials for pro-cesses. Symbiosis programme aims to promote industrial symbiosis by identifying possible synergies. In the United Kingdom (UK), a national level programme NISP (National Industri-al Symbiosis Programme) has been successfully implemented. This thesis studies whether it would be possible to implement a similar program in Finland. The implementation of the pro-gram in Finland is evaluated by analyzing and comparing Finnish and British business envi-ronments using PESTEL and diamond models. The goal is to identify factors that promote or hinder the implementation of the programme in Finland. Based on this study, it can be said that implementing the programme in Finland is possible. The programme can be carried out in almost the same principles as in the UK, but some char-acteristics of the Finnish business environment, such as the high level of technological know-how, should especially be taken as an advantage. On the other hand, there are features, such as low level domestic demand, which may prevent the implementation of the program unless they are given special attention.

Study of Control Methods of a High-Frequency Cycloconverter for Domestic Induction Heating Appliances

A high-frequency cyclonverter acts as a direct ac-to-ac power converter circuit that does not require a diode bidge rectifier. Bridgeless topology makes it possible to remove forward voltage drop losses that are present in a diode bridge. In addition, the on-state losses can be reduced to 1.5 times the on-state resistance of switches in half-bridge operation of the cycloconverter. A high-frequency cycloconverter is reviewed and the charging effect of the dc-capacitors in ``back-to-back'' or synchronous mode operation operation is analyzed. In addition, a control method is introduced for regulating dc-voltage of the ac-side capacitors in synchronous operation mode. The controller regulates the dc-capacitors and prevents switches from reaching overvoltage level. This can be accomplished by variating phase-shift between the upper and the lower gate signals. By adding phase-shift between the gate signal pairs, the charge stored in the energy storage capacitors can be discharged through the resonant load and substantially, the output resonant current amplitude can be improved. The above goals are analyzed and illustrated with simulation. Theory is supported with practical measurements where the proposed control method is implemented in an FPGA device and tested with a high-frequency cycloconverter using super-junction power MOSFETs as switching devices.

Feeling vs. Being like a Domestic Goddess: Cookbooks and Lifestyle Choices

Tämä pro gradu -tutkielma tarkastelee, miten keittokirjat muovaavat pääasiassa naispuolista lukijakuntaansa. Tärkein kysymys, johon tutkielmassa on etsitty vastausta on, että onko naisilla, menneiden sukupolvien taisteltua vuosikymmeniä tasa-arvon puolesta, oikeus valita viettää aikaa keittiössä ja oikeasti nauttiakin siitä. Kahtena päälähteenä tutkielmassa on käytetty brittiläisen Nigella Lawsonin keittokirjoja How to Eat ja How to be a Domestic Goddess. Näiden kirjojen analysoinnin ja muiden lähteiden avulla tutkielmassa on käsitelty ruuanlaiton ja leipomisen nautittavuutta ja sitä onko se ylipäätään sallittua vai syntistä. Lawson on julkaissut urallaan sitten vuoden 1998 yhteensä yhdeksän keittokirjaa, joiden lisäksi kirjojen tueksi on tehty useita televisiosarjoja. How to Eat on yleispätevä opas hyvän ruuan nautintoihin ja periaatteisiin, How to be a Domestic Goddess taas sisältää lähinnä leivontareseptejä. Nämä kaksi kirjaa ovat Lawsonin ensimmäiset keittokirjat. Nigella Lawsonin keittokirjat eivät ole vain reseptikokelmia eivätkä reseptit vain aineisosalistoja ja valmistusohjeita. Lawsonin kirjoja voi lukea kirjallisuutena eikä vain reseptien takia. Lawson viittaa usein naisen asemaan ja yrittää vakuuttaa lukijoitaan ruuanlaiton ja leipomisen nautittavuudesta.

Optimization of PV and battery capacity for domestic purposes

The usage of PV batteries nowadays became more and more widely spread. Due to the fact that the efficiency of modern PV is rising every year the prevalence of this source of energy is increasing. As the source of the energy is sunlight, these batteries need to be complimented by storage capacitors which will store energy for future use. Nevertheless the less the calculation of demanded amount of energy according the load and capacity of a storage battery that will keep the end consumer in work during certain time still is not overviewed. In this thesis the overall system will be considered and there will be made economic calculations for configurations of such system that will depend from the load. Also the behavior of the system in different geographical and climate conditions that influence of the amount of energy produced will be overviewed.