Hylynkäsittelyn ja annostelun vaikutus kartongin laatuun

Tämän työn tavoitteena oli löytää keinot taivekartongin riittävän z-suuntaisen lujuuden saavuttamiseksi tilanteessa, jossa runkokerrokseen annosteltavan hylyn määrää joudutaan pysyvästi vähentämään. Työn kirjallisuusosassa selvitettiin taivekartongin tärkeimmät ominaisuudet, joista tarkemmin tarkasteltiin palstautumislujuutta ja siihen vaikuttavia tekijöitä. Lisäksi käytiin läpi palstautumislujuuden mittausmenetelmät. Merkittävimpiä teoriaosassa käsiteltyjä palstautumislujuuteen vaikuttavia tekijöitä olivat massojen käsittely ja annostelu, kuivalujalisäaineiden käyttö sekä rainanmuodostus. Hylyn annosteluosuuden pienentäminen vähensi taivekartongin paksuussuuntaista lujuutta ja runkomassan vedenpoistovastusta, mutta samanaikaisesti lisääntyivät kartongin paksuus ja taivutusjäykkyys. Hylyn vähäisemmän käytön seurauksena menetettyä lujuutta ei pystytty palauttamaan hylyn jauhatuksen määrää lisäämällä, eikä kartonkikoneen runkoviiraosan vedenpoistoon vaikuttamalla. Kun hylyn annosteluosuus laskettiin 20 %:in, saavutettiin runkokerroksen riittävä lujuus ainoastaan runkomassan pääkomponenttina käytettävän hiokemassaseoksen jauhatusastetta nostamalla tai korvaamalla pieni osa hiokkeesta hyvin hienoksi jauhetulla mäntysellulla. Hiokkeen freeness oli laskettava tasolta 300 ml CSF tasolle 250 ml CSF. Vastaavasti mäntysellu oli jauhettava hyvin pitkälle (°SR 74) tai annosteluosuuden oli oltava vähintään 2 %, jolloin jauhatusaste °SR 49 oli riittävä. Vähäisemmällä hylyn käytöllä saavutettu etu vedenpoistossa saatettaisiin menettää näiden toimenpiteiden vaikutuksesta.

Fiber-reinforced composite fixed dental prostheses: Studies of the materials used as pontics

Fiber-reinforced composite fixed dental prostheses – Studies of the materials used as pontics University of Turku, Faculty of Medicine, Institute of Dentistry, Department of Biomaterials Science, Finnish Doctoral Program in Oral Sciences – FINDOS, Annales Universitatis Turkuensis, Turku, Finland 2015 Fiber-reinforced composites (FRC), a non-metallic biomaterial, represent a suitable alternative in prosthetic dentistry when used as a component of fixed dental prostheses (FDPs). Some drawbacks have been identified in the clinical performance of FRC restorations, such as delamination of the veneering material and fracture of the pontic. Therefore, the current series of studies were performed to investigate the possibilities of enhancing the mechanical and physical properties of FRC FDPs by improving the materials used as pontics, to then heighten their longevity. Four experiments showed the importance of the pontic design and surface treatment in the performance of FRC FDPs. In the first, the load-bearing capacities of inlay-retained FRC FDPs with pontics of various materials and thicknesses were evaluated. Three different pontic materials were assessed with different FRC framework vertical positioning. Thicker pontics showed increased load-bearing capacities, especially ceramic pontics. A second study was completed investigating the influence of the chemical conditioning of the ridge-lap surface of acrylic resin denture teeth on their bonding to a composite resin. Increased shear bond strength demonstrated the positive influence of the pretreatment of the acrylic surfaces, indicating dissolution of the denture surfaces, and suggesting potential penetration of the monomer systems into the surface of denture teeth. A third study analyzed the penetration depth of different monomer systems on the acrylic resin denture teeth surfaces. The possibility of establishing a durable bond between acrylic pontics and FRC frameworks was demonstrated by the ability of monomers to penetrate the surface of acrylic resin denture teeth, measured by a confocal scanning type microscope. A fourth study was designed to evaluate the load-bearing capacities of FRC FDPs using the findings of the previous three studies. In this case, the performance of pre-shaped acrylic resin denture teeth used as pontics with different composite resins as filling materials was evaluated. The filling material influenced the load-bearing capacities, providing more durable FRC FDPs. It can be concluded that the mechanical and physical properties of FRC FDPs can be improved as has been shown in the development of this thesis. The improvements reported then might provide long lasting prosthetic solutions of this kind, positioning them as potentially permanent rehabilitation treatments. Key words: fiber-reinforced composite, fixed dental prostheses, inlay-retained bridges, adhesion, acrylic resin denture teeth, dental material.

Reconstruction of cranial bone defects with fiber-reinforced composite–bioactive glass implants

A cranial bone defect may result after an operative treatment of trauma, infection, vascular insult, or tumor. New biomaterials for cranial bone defect reconstructions are needed for example to mimic the biomechanical properties and structure of cranial bone. A novel glass fiber-reinforced composite implant with bioactive glass particulates (FRC–BG, fiber-reinforced composite–bioactive glass) has osteointegrative potential in a preclinical setting. The aim of the first and second study was to investigate the functionality of a FRC–BG implant in the reconstruction of cranial bone defects. During the years 2007–2014, a prospective clinical trial was conducted in two tertiary level academic institutions (Turku University Hospital and Oulu University Hospital) to evaluate the treatment outcome in 35 patients that underwent a FRC–BG cranioplasty. The treatment outcome was good both in adult and pediatric patients. A number of conventional complications related to cranioplasty were observed. In the third study, a retrospective outcome evaluation of 100 cranioplasty procedures performed in Turku University Hospital between years 2002–2012 was conducted. The experimental fourth study was conducted to test the load-bearing capacity and fracture behavior of FRC–BG implants under static loading. The interconnective bars in the implant structure markedly increased the load-bearing capacity of the implant. A loading test did not demonstrate any protrusions of glass fibers or fiber cut. The fracture type was buckling and delamination. In this study, a postoperative complication requiring a reoperation or removal of the cranioplasty material was observed in one out of five cranioplasty patients. The treatment outcomes of cranioplasty performed with different synthetic materials did not show significant difference when compared with autograft. The FRC–BG implant was demonstrated to be safe and biocompatible biomaterial for large cranial bone defect reconstructions in adult and pediatric patients.