Reliability of SMD interconnections on flexible low-temperature substrates with inkjet-printed conductors

julkaisumaa: NLD

DFM(A)-Aspects of an Advanced Cable Gland Design

Nowadays typical motor junction boxes do not incorporate cable glands, which would provide good electrical performance interms of electromagnetic compatibility. In this paper, a manufacturability and assembly analysis for the new construction of a rigid body feeder cable junction of an electric motor is presented especially for converter drives (practical tests were carried out at LUT during 2007). Although the cable junction should also clamp the cable to provide enough tensile strength, the phase conductors should not get squashed by the groundingconnection. In order to ensure good performance in an electrical mean especially in converter drives, the grounding of the cable should be connected 360 degrees around the cable. In this paper, following manufacturing technologies are discussed: traditional turning, precision and centrifugal casting, and rotation moulding. DFM(A)-aspects are presented in detail.

Elinkaarikustannusten ja toimitusvarmuuden analysointi sähkönjakelun saneerausmenetelmille

Tässä työssä tutkitaan haja-asutusalueiden sähkönjakeluverkkojen kehittämistä. Kehityskohteiksi on valittu viisi tekniikkaa, 1000 V-järjestelmä, keskijännitejohtojen siirtäminen teiden varsille, PAS -johtojen käyttö, maakaapelointi sekä pylväskatkaisijan käyttö. Teoreettisen tarkastelun tavoitteena on määrittää reunaehdot tarkasteltavien tekniikoiden kannattavuudelle. Aiemmin keskijänniteverkko on rakennettu lähes poikkeuksetta avojohtona. Viime vuosien myrskyt sekä lumikuormat ovat häirinneet sähkönjakelua ja nostaneet painetta jakeluvarmuuden kasvattamiseksi. Tutkimuksessa haja-asutusalueiden sähkönjakeluverkon kehittämiseen etsitään teknillisesti sekä taloudellisesti kannattavia ratkaisumalleja. Kehittämisen tavoitteena on parantaa kuluttajien sähkön laatua ja toimitusvarmuutta. Tutkimuksessa käsitellään tarkasteltavia tekniikoita esimerkkikohteiden avulla, jotka on valittu Itä-Suomelle tyypillisiltä jakelualueilta. Kohteissa taloudellista kannattavuutta tutkitaan vertaamalla perinteistä saneeraamista tarkastelussa oleviin korvaaviin menetelmiin. Korvaavilla ratkaisuilla toimitusvarmuus paranee, mutta kannattavuus riippuu siirrettävästä tehosta, asiakasryhmien jakaumasta sekä saavutettavasta vikataajuuden muutoksesta.

Haja-asutusalueen keskijänniteverkon kaapeloinnin ja automaation suunnittelumetodiikka

Tässä diplomityössä tutkitaan erilaisia keskijänniteverkon kehittämismenetelmiä sekä suunnittelua haja-asutusalueelle. Suunnittelumetodiikan perustana on vertailla sähköverkon käyttövarmuuden tunnuslukujen sekä kokonaiskustannusten kehittymistä erilaisilla investointiratkaisuilla. Lähemmässä tarkastelussa ovat erilaiset kaapelointimenetelmät sekä automaatiolaitteet kuten maastoon sijoitettavat katkaisijat sekä kauko-ohjattavat erottimet. Kehittämisratkaisujen vertailemiseksi sähköverkosta muodostetaan laskentaa varten malli, jonka avulla on mahdollista tarkastella mm. käyttövarmuuden tunnuslukujen sekä verkon kustannusten kehittymistä. Verkon kustannuksissa otetaan huomioon investointikustannukset, käyttö- ja kunnossapitokustannukset, viankorjauskustannukset sekä keskeytyskustannukset. Keskeytysten laskentaa varten toteutetaan erilliset laskentalohkot, jotta keskeytyskustannukset saadaan mallinnettua tarkasti. Kaapelointistrategia-analyysissä vertaillaan kaapeloinnin erilaisia toteuttamisperiaatteita. Erilaisia tutkittavia kaapelointimenetelmiä ovat vyörytysmenetelmä, vikaherkimpien kohteiden uusinta, vanhimpien kohteiden uusinta, täydellinen kaapelointi sekä optimiverkostoratkaisu, jossa on hyödynnetty keskijännitejohtojen kaapeloinnin lisäksi mm. automaatioratkaisuja ja 1000 V tekniikkaa. Kaapelointimenetelmiä vertailtaessa on havaittu, että vikaherkimmistä kohteista aloitettava saneeraus tuottaa parhaimman tuloksen, jos optimiratkaisua ei oteta huomioon.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Wind Turbine Direct-Drive Permanent-Magnet Generator with Direct Liquid Cooling for Mass Reduction

Today’s electrical machine technology allows increasing the wind turbine output power by an order of magnitude from the technology that existed only ten years ago. However, it is sometimes argued that high-power direct-drive wind turbine generators will prove to be of limited practical importance because of their relatively large size and weight. The limited space for the generator in a wind turbine application together with the growing use of wind energy pose a challenge for the design engineers who are trying to increase torque without making the generator larger. When it comes to high torque density, the limiting factor in every electrical machine is heat, and if the electrical machine parts exceed their maximum allowable continuous operating temperature, even for a short time, they can suffer permanent damage. Therefore, highly efficient thermal design or cooling methods is needed. One of the promising solutions to enhance heat transfer performances of high-power, low-speed electrical machines is the direct cooling of the windings. This doctoral dissertation proposes a rotor-surface-magnet synchronous generator with a fractional slot nonoverlapping stator winding made of hollow conductors, through which liquid coolant can be passed directly during the application of current in order to increase the convective heat transfer capabilities and reduce the generator mass. This doctoral dissertation focuses on the electromagnetic design of a liquid-cooled direct-drive permanent-magnet synchronous generator (LC DD-PMSG) for a directdrive wind turbine application. The analytical calculation of the magnetic field distribution is carried out with the ambition of fast and accurate predicting of the main dimensions of the machine and especially the thickness of the permanent magnets; the generator electromagnetic parameters as well as the design optimization. The focus is on the generator design with a fractional slot non-overlapping winding placed into open stator slots. This is an a priori selection to guarantee easy manufacturing of the LC winding. A thermal analysis of the LC DD-PMSG based on a lumped parameter thermal model takes place with the ambition of evaluating the generator thermal performance. The thermal model was adapted to take into account the uneven copper loss distribution resulting from the skin effect as well as the effect of temperature on the copper winding resistance and the thermophysical properties of the coolant. The developed lumpedparameter thermal model and the analytical calculation of the magnetic field distribution can both be integrated with the presented algorithm to optimize an LC DD-PMSG design. Based on an instrumented small prototype with liquid-cooled tooth-coils, the following targets have been achieved: experimental determination of the performance of the direct liquid cooling of the stator winding and validating the temperatures predicted by an analytical thermal model; proving the feasibility of manufacturing the liquid-cooled tooth-coil winding; moreover, demonstration of the objectives of the project to potential customers.

Application of Carbon Nanotubes in Rotating Electrical Machines

Demand for increased energy efficiency has put an immense need for novel energy efficient systems. Electrical machines are considered as a much matured technology. Further improvement in this technology needs of finding new material to incorporate in electrical machines. Progress of carbon nanotubes research over the latest decade can open a new horizon in this aspect. Commonly known as ‘magic material’, carbon nanotubes (CNTs) have promising material properties that can change considerably the course of electrical machine design. It is believed that winding material based on carbon nanotubes create the biggest hope for a giant leap of modern technology and energy efficient systems. Though carbon nanotubes (CNTs) have shown amazing properties theoretically and practically during the latest 20 years, to the best knowledge of the author, no research has been carried out to find the future possibilities of utilizing carbon nanotubes as conductors in rotating electrical machines. In this thesis, the possibilities of utilizing carbon nanotubes in electrical machines have been studied. The design changes of electrical machine upon using carbon nanotubes instead of copper have been discussed vividly. A roadmap for this carbon nanotube winding machine has been discussed from synthesis, manufacturing and operational points of view.

Hiilinanojohteiden makroskooppinen johtavuus

Hiilinanojohteet ovat sähkönjohteita, joiden valmistuksessa on käytetty hiilinanoputkia, eli yhden atomikerroksen paksuisesta hiiliatomiverkosta koostuvia rakenteita. Hiilinanoputket ovat viime vuosina keränneet suurta mielenkiintoa erinomaisten fysikaalisten ominaisuuksiensa ansiosta. Tämän työn tavoitteena on selvittää, voitaisiinko hiilinanojohteiden sähkönjohtavuus saada riittävälle tasolle, jotta niillä saatettaisiin korvata nykyisiä kuparista valmistettuja johteita. Vaikka kuparilla on erinomainen johtavuus, sen käytöllä on omat heikkoutensa, kuten korkea hinta, virran ahtautuminen, suuri tiheys ja heikko mekaaninen kestävyys. Hiilinanojohteet voisivat olla yksi osa-alue kehitettäessä uusia energiatehokkaita ja ympäristöystävällisiä laitteita nyky-yhteiskunnan tarpeisiin. Työn tulosten perusteella voidaan todeta, että nykyisten hiilinanojohteiden sähkönjohtavuus on yhä liian pieni laajamittaiseen käyttöön. Johtavuus on kuitenkin lisääntynyt jatkuvasti viime vuosina. Kehitystyön avulla hiilimateriaalin potentiaalia saadaan hyödynnettyä koko ajan enemmän, ja ajan myötä hiilijohteista voi tulla varteenotettava kilpailija perinteisille johdemateriaaleille. Hiilinanojohteet tulevat luultavasti aluksi yleistymään käyttökohteissa, joissa niiden muut ominaisuudet täydentävät hyvin sähkönjohtavuutta.

Permanent magnet synchronous generator design solution for large directdrive wind turbines: Thermal behavior of the LC DD-PMSG

Wind is one of the most compelling forms of indirect solar energy. Available now, the conversion of wind power into electricity is and will continue to be an important element of energy self-sufficiency planning. This paper is one in a series intended to report on the development of a new type of generator for wind energy; a compact, high-power, direct-drive permanent magnet synchronous generator (DD-PMSG) that uses direct liquid cooling (LC) of the stator windings to manage Joule heating losses. The main param-eters of the subject LC DD-PMSG are 8 MW, 3.3 kV, and 11 Hz. The stator winding is cooled directly by deionized water, which flows through the continuous hollow conductor of each stator tooth-coil winding. The design of the machine is to a large degree subordinate to the use of these solid-copper tooth-coils. Both steady-state and timedependent temperature distributions for LC DD-PMSG were examined with calculations based on a lumpedparameter thermal model, which makes it possible to account for uneven heat loss distribution in the stator conductors and the conductor cooling system. Transient calculations reveal the copper winding temperature distribution for an example duty cycle during variable-speed wind turbine operation. The cooling performance of the liquid cooled tooth-coil design was predicted via finite element analysis. An instrumented cooling loop featuring a pair of LC tooth-coils embedded in a lamination stack was built and laboratory tested to verify the analytical model. Predicted and measured results were in agreement, confirming the predicted satisfactory operation of the LC DD-PMSG cooling technology approach as a whole.

Optical and photoelectric properties of dry bacteriorhodopsin sensors

In this thesis, bacteriorhodopsin (BR) photosensor’s optical and electrical properties were studied. The BR sensor consisted of a dry film with BR in polyvinyl alcohol and covered with transparent conductors. In the experiments the BR photocycle was started with two lasers. The characteristics of the BR sensor were measured in two ways. The first approach was theoretical and it required knowing the laser parameters. The second way required assembling a measurement setup for the optical response measurements. However, no measurable results were obtained due to low laser power. The photoelectric response was measured in the experiments with two laser systems and the amplifier was tested. In the experiment with a Cavitar laser, the photoelectric response was obtained. In the experiment with FemtoFiber Pro laser, the photoelectric response was not measured. The expected amplitude of the response was obtained. The experimental data was analyzed and possible solutions for reducing the interference were given.