Management of Metals in the Pulping Process

Diplomityön tarkoituksena oli löytää keino korkean mangaanipitoisuuden hallintaan ECF-valkaisussa. Kirjallisuusosassa käsiteltiin eri metallien ja kuidun vuorovaikutuksia sekä niiden vaikutuksia prosessiin. Lisäksi käytiin läpi sellunvalmituksen yleisimpiä metallienhallintamenetelmiä. Työn kokeellisessa osassa tehtiin esikokeina laboratoriokokeita, jotta löydettiin oikeat kelatointistrategiat tehdasmittakaavan koeajoille. Laboratoriovalkaisut suoritettiin kuudella eri kemikaalilla käyttäen DD3-pesurin jälkeistä massaa ja samanlaisia parametrejä kuin tehdasvalkaisussa. Kolmesta eri valkaisusekvenssistä paras tulos saavutettiin D0-QEP-sekvenssillä. Tehdasmittakaavan koeajojen tavoitteena oli saavuttaa alle 1 mg/kg jäännösmangaanipitoisuus valkaistussa massassa ja korkeampi vaaleus EOP-vaiheessa pienemmällä klooridioksidin kulutuksella. Koeajoissa käytettiinDTPA:ta ja EDTA:ta kahdeksassa eri koepisteessä. Pienimpiin jäännöspitoisuuksiin päästiin koepisteissä, joissa kelatointiaine annosteltiin ennen valkaisun viimeistä pesuvaihetta tai sen jälkeen. Samanlaisia tuloksia saavutettiin koepisteissä, joissa kelatointiaine lisättiin suoraan EOP-vaiheeseen. Tällöin kelatointiaineen käyttö johti myös korkeampaan vaaleuteen EOP-vaiheessa pienemmällä kappakertoimella kuin referenssissä. Säästöt klooridioksidin kulutuksessa eivät olleet kuitenkaan tarpeeksi suuret kattaakseen kelatointiaineiden käytön kustannuksia. Kustannustehokkain tapa kontrolloida jäännösmangaanipitoisuutta oli EDTA:n annostelu D2 DD-pesurin jälkeen. Haittapuolena tälläisessä kelatoinnissa oli metallikompleksien palautuminen valkaisuun kuivauskoneen kiertoveden mukana. Tärkeimmät onnistuneeseen kelatointiin vaikuttavat parametrit olivat lajittelussa käytetyn rikkihapon annos, D0-vaiheen pH ja D0 DD-pesurin pesutehokkuus.

Optimization of the procedure for removing iron deposits on ceramic filter media

In this thesis, cleaning of ceramic filter media was studied. Mechanisms of fouling and dissolution of iron compounds, as well as methods for cleaning ceramic membranes fouled by iron deposits were studied in the literature part. Cleaning agents and different methods were closer examined in the experimental part of the thesis. Pyrite is found in the geologic strata. It is oxidized to form ferrous ions Fe(II) and ferric ions Fe(III). Fe(III) is further oxidized in the hydrolysis to form ferric hydroxide. Hematite and goethite, for instance, are naturally occurring iron oxidesand hydroxides. In contact with filter media, they can cause severe fouling, which common cleaning techniques competent enough to remove. Mechanisms for the dissolution of iron oxides include the ligand-promoted pathway and the proton-promoted pathway. The dissolution can also be reductive or non-reductive. The most efficient mechanism is the ligand-promoted reductive mechanism that comprises two stages: the induction period and the autocatalytic dissolution.Reducing agents(such as hydroquinone and hydroxylamine hydrochloride), chelating agents (such as EDTA) and organic acids are used for the removal of iron compounds. Oxalic acid is the most effective known cleaning agent for iron deposits. Since formulations are often more effective than organic acids, reducing agents or chelating agents alone, the citrate¿bicarbonate¿dithionite system among others is well studied in the literature. The cleaning is also enhanced with ultrasound and backpulsing.In the experimental part, oxalic acid and nitric acid were studied alone andin combinations. Also citric acid and ascorbic acid among other chemicals were tested. Soaking experiments, experiments with ultrasound and experiments for alternative methods to apply the cleaning solution on the filter samples were carried out. Permeability and ISO Brightness measurements were performed to examine the influence of the cleaning methods on the samples. Inductively coupled plasma optical emission spectroscopy (ICP-OES) analysis of the solutions was carried out to determine the dissolved metals.

Mangaani mekaanisen massan peroksidivalkaisussa

Mangaanilla on havaittu olevan haitallisia vaikutuksia mekaanisen massan peroksidivalkaisussa. Suurin ongelma on mangaanin katalyyttisen aktiivisuuden aiheuttama peroksidin hajoaminen. On havaittu, että mangaanin hapetusasteella voisi olla merkittävä vaikutus mangaanin kelatoitumiseen sekä sen katalysoimaan peroksidin hajoamiseen valkaisun aikana. Työssä selvitettiin, miten massan mangaanipitoisuus ja mangaanin hapetusasteen muutos vaikuttavat valkaisuun ja mangaanin kelatoitumiseen. Laboratoriokokeiden tulokset osoittavat, että mangaani kelatoituu hapetusasteilla +II ja +III happamissa oloissa yhtä hyvin. pH:n nousu heikentää enemmän hapetusasteella +III olevan mangaanin kelatoitumista. Mangaani ei kelatoidu hapetusasteella +IV lainkaan. Valkaisukokeiden perusteella mangaani katalysoi peroksidin hajoamista hapetusasteilla +II ja +III yhtä voimakkaasti, mikä näkyy samalla vaaleuden nousun heikkenemisenä peroksidin määrän vähetessä. Mn(IV) ei katalysoi peroksidin hajoamista ollenkaan ja sen vaikutus vaaleuteen on selvästi pienempi kuin hapetusasteilla +II ja +III. Laboratoriokokeiden tulokset osoittavat myös, että kompleksinmuodostajalla on valkaisussa selvä positiivinen vaikutus. DTPA estää hapetusasteen +II katalyyttistä aktiivisuutta voimakkaammin kuin hapetusasteen +III. Valkaisusakeuden nosto pienensi mangaanin katalyyttistä aktiivisuutta, minkä oletettiin johtuvan stabilointikemikaalien konsentraation noususta.

Epäpuhtauksien vaikutus monokaliumfosfaattikiteen kasvuun

Työssä on tutkittu epäpuhtauksien vaikutusta kastelulannoitesuolojen monokaliumfosfaatin, kaliumnitraatin ja ureafosfaatin kiteytyksessä. Kirjallisuusosassa on käsitelty kastelulannoiteprosessit ja epäpuhtauksien vaikutus kastelulannoitteiden valmistuksessa. Kiteytys ja kiteenkasvu on esitetty perusyhtälöin, joissa on otettu epäpuhtauksien vaikutus huomioon. Tarkemmin on perehdytty monokaliumfosfaatin kiteytykseen ja kolmenarvoisten kationeiden, Al3+, Fe3+ ja Cr3+, vaikutukseen kiteiden kasvuun. Kolmenarvoiset metalli-ionit adsorboituvat kiteen pintaan haitaten kiteenkasvua, mikä vaikuttaa erityisesti kiteen prismapinnan kasvuun. Lisäksi on esitelty muita kiteenkasvuun vaikuttavia olosuhteita. Lopuksi on käsitelty kompleksinmuodostajia metalli-ionien haitallisten vaikutusten ehkäisijöinä. Kokeellisessa osassa suoritettiin liukoisuuskokeita monokaliumfosfaatin liukoisuuden selvittämiseksi eri pH-olosuhteissa. Suoritetuissa yksikidekokeissa tutkittiin pH:n ja kolmenarvoisten kationeiden; Al3+, Fe3+ ja Cr3+, vaikutus monokaliumfosfaattikiteen pituus- ja leveyskasvuun ja kidemuotoon eri ylikylläisyyksillä. Lisäksi tutkittiin voidaanko lämpötilaa ja pH muuttamalla tai pyrofosfaattia lisäämällä poistaa raudan kasvua inhiboima vaikutus. Kiteytyslämpötilaa nostamalla voidaan poistaa raudan haitallinen vaikutus kiteen kasvuun.

Biohajoavat kompleksinmuodostajat mekaanisen massan peroksidivalkaisussa

Mekaanisen massan peroksidivalkaisussa on perinteisesti käytetty kahta kompleksinmuodostajaa, jotka ovat dietyleenitriamiinipentaetikkahappo (DTPA) ja etyleenidiamiinipentaetikkahappo (EDTA). Kompleksinmuodostajat saavat aikaan hyvän kelatointituloksen muodostamalla valkaisulle haitallisten metalli-ionien kanssa kompleksin ja estäen näin metalli-ionien valkaisutulosta huonontavan vaikutuksen. Perinteiset kompleksinmuodostajat DTPA ja EDTA eivät kuitenkaan ole biohajoavia ja niiden epäillään irrottavan metalleja vesistöjen sedimenteistä. Työssä selvitettiin kolmen eri biohajoavan kompleksinmuodostajan valkaisuteho verrattuna perinteisiin kompleksinmuodostajiin. Laboratoriossa suoritetut pesukokeet osoittivat, että mikään biohajoava kompleksinmuodostaja ei saavuttanut samaa pesutehoa kuin perinteiset kompleksinmuodostajat. Valkaisukokeet kuitenkin osoittivat, että biohajoava kompleksinmuodostaja ISA pääsi hyvin lähelle perinteisten kompleksinmuodostajien valkaisutuloksia suoritettaessa valkaisu siten, että massa esipestään kompleksinmuodostajalla ja sen jälkeen valkaistaan vakiokemikaaliannoksella alkalina ollessa natriumhydroksidi. Kaksi muuta biohajoavaa kompleksinmuodostajaa, ISA+EDDS ja HAS, eivät saavuttaneet samaa tasoa. HAS toimi kyllä stabilaattorina, muttei pystynyt nostamaan massan vaaleutta.

EDTA- and DTPA-functionalized silica gel and chitosan adsorbents for the removal of heavy metals from aqueous solutions

Adsorbents functionalized with chelating agents are effective in removal of heavy metals from aqueous solutions. Important properties of such adsorbents are high binding affinity as well as regenerability. In this study, aminopolycarboxylic acid, EDTA and DTPA, were immobilized on the surface of silica gel, chitosan, and their hybrid materials to achieve chelating adsorbents for heavy metals such as Co(II), Ni(II), Cd(II), and Pb(II). New knowledge about the adsorption properties of EDTA- and DTPA-functionalizedadsorbents was obtained. Experimental work showed the effectiveness, regenerability, and stability of the studied adsorbents. Both advantages and disadvantages of the adsorbents were evaluated. For example, the EDTA-functionalized chitosan-silica hybrid materials combined the benefits of the silica gel and chitosan while at the same time diminishing their observed drawbacks. Modeling of adsorption kinetics and isotherms is an important step in design process. Therefore, several kinetic and isotherm models were introduced and applied in this work. Important aspects such as effect of error function, data range, initial guess values, and linearization were discussed and investigated. The selection of the most suitable model was conducted by comparing the experimental and simulated data as well as evaluating the correspondence between the theory behind the model and properties of the adsorbent. In addition, modeling of two-component data was conducted using various extended isotherms. Modeling results for both one- and twocomponent systems supported each other. Finally, application testing of EDTA- and DTPA-functionalized adsorbents was conducted. The most important result was the applicability of DTPA-functionalized silica gel and chitosan in the capturing of Co(II) from its aqueous EDTA-chelate. Moreover, these adsorbents were efficient in various solution matrices. In addition, separation of Ni(II) from Co(II) and Ni(II) and Pb(II) from Co(II) and Cd(II) was observed in two- and multimetal systems. Lastly, prior to their analysis, EDTA- and DTPA-functionalized silica gels were successfully used to preconcentrate metal ions from both pure and salty waters

Chelating Adsorbents in Purification of Hydrometallurgical Solutions

In this thesis, equilibrium and dynamic sorption properties of weakly basic chelating adsorbents were studied to explain removal of copper, nickel from a concentrated zinc sulfate solution in a hydrometallurgical process. Silica-supported chelating composites containing either branched poly(ethyleneimine) (BPEI) or 2-(aminomethyl)pyridine (AMP) as a functional group were used. The adsorbents are commercially available from Purity Systems Inc, USA as WP-1® and CuWRAM®, respectively. The fundamental interactions between the adsorbents, sulfuric acid and metal sulfates were studied in detail and the results were used to find the best conditions for removal of copper and nickel from an authentic ZnSO4 process solution. In particular, the effect of acid concentration and temperature on the separation efficiency was considered. Both experimental and modeling aspectswere covered in all cases. Metal sorption is considerably affected by the chemical properties of the studied adsorbents and by the separation conditions. In the case of WP-1, acid affinity is so high that column separation of copper, nickel and zinc has to be done using the adsorbent in base-form. On the other hand, the basicity of CuWRAM is significantly lower and protonated adsorbent can be used. Increasing temperature decreases the basicity and the metals affinity of both adsorbents, but the uptake capacities remain practically unchanged. Moreover, increasing temperature substantially enhances intra-particle mass transport and decreases viscosities thus allowing significantly higher feed flow rates in the fixed-bed separation. The copper selectivity of both adsorbents is very high even in the presence of a 250-fold excess of zinc. However, because of the basicity of WP-1, metal precipitation is a serious problem and therefore only CuWRAM is suitable for the practical industrial application. The optimum temperature for copper removal appears to be around 60 oC and an alternative solution purification method is proposed. The Ni/Zn selectivity of both WP-1 and CuWRAM is insufficient for removal of the very small amounts of nickel present in the concentrated ZnSO4 solution.

Studies on 68Ga-Based Agents for PET Imaging of Cancer and Inflammation

Studies on ⁶⁸Ga-Based Agents for PET Imaging of Cancer and Inflammation Positron emission tomography (PET) is based on the use of radiolabeled agents and facilitates in vivo imaging of biological processes, such as cancer. Because the detection of cancer is demanding and is often obscured by inflammation, there is a demand for better PET imaging agents. The aim was to preliminarily evaluate new PET agents for imaging cancer and inflammation using experimental models. ⁶⁸Ga-chloride and peptides, ⁶⁸Ga-labeled through 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid (DOTA), targeting matrix metalloproteinase-9 (MMP-9) were tested for tumor imaging. In addition, a ⁶⁸Ga-DOTA-conjugated peptide targeting vascular adhesion protein-1 (VAP-1), was tested for inflammation imaging. The ⁶⁸Ga-based imaging agents described here showed potential features by passing the essential in vitro tests, proceeding further to preclinical in vivo evaluation and being able to visualize the target. The target uptake and target-to-background ratios of ⁶⁸Ga-based agents were, however, not optimal. ⁶⁸Ga-chloride showed slow clearance caused by its binding to blood transferrin. In the case of ⁶⁸Ga-DOTA-peptides low in vivo stability and/or low lipophilicity led to too rapid blood clearance and urinary excretion. The properties of ⁶⁸Ga-labeled peptides are modifiable, as shown with matrix metalloproteinase-9 targeting ligands. In the conclusion of this PhD thesis, ⁶⁸Ga-based agents for PET imaging of cancer and inflammation could be applied in the development of drugs, earlier diagnostics and following-up of the efficacy of therapies.

Studies on Neuromuscular Blocking Agents and Their Antagonists During Anaesthesia

Neuromuscular blocking agents (NMBAs) are widely used in clinical anaesthesia and emergency medicine. Main objectives are to facilitate endotracheal intubation and to allow surgery by reducing muscle tone and eliminating sudden movements, which may otherwise lead to trauma and complications. The most commonly used NMBAs are non-depolarizing agents with a medium duration of action, such as rocuronium and cisatracurium. They bind to the acetylcholine receptors in the neuromuscular junction, thus inhibiting the depolarization of the postsynaptic (muscular) membrane, which is a prerequisite for muscle contraction to take place. Previously, it has been assumed that nitrous oxide (N2O), which is commonly used in combination with volatile or intravenous anaesthetics during general anaesthesia, has no effect on NMBAs. Several studies have since claimed that N2O in fact does increase the effect of NMBAs when using bolus administration of the relaxant. The effect of N2O on the infusion requirements of two NMBAs (rocuronium and cisatracurium) with completely different molecular structure and pharmacological properties was assessed. A closed-loop feedback controlled infusion of NMBA with duration of at least 90 minutes at a 90% level of neuromuscular block was used. All patients received total intravenous anaesthesia (TIVA) with propofol and remifentanil. In both studies the study group (n=35) received N2O/Oxygen and the control group (n=35) Air/Oxygen. There were no significant differences in the mean steady state infusion requirements of NMBA (rocuronium in Study I; cisatracurium in Study II) between the groups in either study. In Study III the duration of the unsafe period of recovery after reversal of rocuronium-induced neuromuscular block by using neostigmine or sugammadex as a reversal agent was analyzed. The unsafe period of recovery was defined as the time elapsed from the moment of no clinical (visual) fade in the train-of-four (TOF) sequence until an objectively measured TOF-ratio of 0.90 was achieved. The duration of these periods were 10.3 ± 5.5 and 0.3 ± 0.3 min after neostigmine and sugammadex, respectively (P < 0.001). Study IV investigated the possible effect of reversal of a rocuronium NMB by sugammadex on depth of anaesthesia as indicated by the bispectral index and entropy levels in thirty patients. Sugammadex did not affect the level of anaesthesia as determined by EEG-derived indices of anaesthetic depth such as the bispectral index and entropy.

Bonding of Composite Resin to Alumina and Zirconia Ceramics with Special Emphasis on Surface Conditioning and Use of Coupling Agents

Dental oxide ceramics have been inspired by their biocompability and mechanical properties which have made durable all-ceramic structures possible. Clinical longevity of the prosthetic structures is dependent on effective bonding with luting cements. As the initial shear bond strength values can be comparable with several materials and procedures, long-term durability is affected by ageing. Aims of the current study were: to measure the shear bond strength of resin composite-to-ceramics and to evaluate the longevity of the bond; to analyze factors affecting the bond, with special emphasis on: the form of silicatization of the ceramic surface; form of silanization; type of resin primer and the effect of the type of the resin composite luting cement; the effect of ageing in water was studied regarding its effect to the endurance of the bond. Ceramic substrates were alumina and yttrium stabilized zirconia. Ceramic conditioning methods included tribochemical silicatization and use of two silane couplings agents. A commercial silane primer was used as a control silane. Various combinations of conditioning methods, primers and resin cements were tested. Bond strengths were measured by shear bond strength method. The longevity of the bond was generally studied by thermocycling the materials in water. Additionally, in one of the studies thermal cycling was compared with long-term water storaging. Results were analysed statistically with ANOVA and Weibull analysis. Tribochemical treatment utilizing air pressure of 150 kPa resulted shear bond strengths of 11.2 MPa to 18.4 MPa and air pressure of 450 kPa 18.2 MPa to 30.5 MPa, respectively. Thermocycling of 8000 cycles or four years water storaging both decreased shear bond strength values to a range of 3.8 MPa to 7.2 MPa whereas initial situation varied from 16.8. Mpa to 23.0 MPa. The silane used in studies had no statistical significance. The use of primers without 10-MDP resulted spontaneous debonding during thermocycling or shear bond strengths below 5 MPa. As conclusion, the results showed superior long-term bonding with primers containing 10-MDP. Silicatization with silanizing showed improved initial shear bond strength values which considerably decreased with ageing in water. Thermal cycling and water storing for up to four years played the major role in reduction of bond strength, which could be due to thermal fatigue of the bonding interface and hydrolytic degradation of the silane coupled interface.

Accountability and corruption : a study into political institutions as referees between principals and agents

Representativ demokrati innebär att medborgare istället för att själv göra beslut i frågor som angår dem, ofta delegerar dylikt beslutsfattande till representanter. Det här betyder att viktiga beslut görs av personer som medborgarna i allmänhet inte känner speciellt väl, och i vars ageranden medborgarna endast har lite insyn. Vanliga medborgare och deras representanter har därtill ofta mycket olika intressen, d.v.s. har olika syn på vad som är viktigt. Representanterna har följaktligen både möjligheter och incitament att missbruka den makt som anförtrotts dem, bl.a. genom korrupt verksamhet. Denna avhandling analyserar mekanismer genom vilka korruption bland representanter kan förebyggas, och (då korrupta handlingar redan ägt rum) upptäckas. Avhandlingen granskar mekanismer som a) ger medborgare och andra ansvarsutkrävare mer information om representanternas målsättningar och ageranden, b) som tvingar representanterna att rättfärdiga sina ageranden gentemot medborgare och andra ansvarsutkrävare, och c) som gör det möjligt för medborgare och andra ansvarsutkrävare att straffa representanter som agerat korrupt. Avhandlingen hävdar att tillämpandet av dylika mekanismer minskar lockelsen för och möjligheterna att engagera sig i korrupta handlingar. Avhandlingen studerar de mekanismer för ansvarsutkrävande som skapas genom politiskt institutionsbyggande. Bl.a. analyseras i vilken grad olika valsystem och typer av maktfördelning gör det möjligt att hålla representanter till svars, och därmed förhindra och upptäcka korruption. Sambandet mellan institutionsbyggande, möjligheter till ansvarsutkrävande och förekomst av korruption studeras på såväl makro- som mikronivå. Studien på makronivå inkluderar ett flertal länder och analyserar sambandet med hjälp av statistisk analys. Studien på mikronivå däremot består av två fallstudier (Österrike och Botswana) och utgör en djupdykning i dessa länders politiska institutioner, möjligheter till ansvarsutkrävande inom ramen för institutionerna, och följder i form av korruption.