Paalutuskoneen vakavuuslaskennan kehittäminen

Tässä diplomityössä tutkitaan paalutuskoneen stabiliteetti- elivakavuuslaskennan toteuttamista yleisesti käytetyn monikappaledynamiikan ohjelmiston avulla. Vakavuuslaskenta kuuluu olennaisena osana paalutuskoneen suunnitteluun ja siitä saadut tulokset asettavat rajat massoille, joita paalutuskone pystyy turvallisesti käsittelemään. Tutkittavana kohteena oli uudentyyppinen poraavapaalutuskone, josta saatiin myös todellista mittaustietoa työssä laaditun simulointimallin toimivuuden arvioimiseksi. Työssä kokeiltiin erityisesti ohjelmiston tarjoamia keinoja laskentaprosessin yksinkertaistamiseksi jasimulointimallin käytön helpottamiseksi. Koska simulointimalli haluttiin säilyttää mahdollisimman yksinkertaisena, porakoneen komponentit mallinnettiin jäykkinä. Mallin ratkaisussa käytettiin staattista ja kvasistaattista analyysia. Dynaamisten voimien vaikutus porakoneeseen otettiin mallissa huomioon lisäämällä massakeskipisteisiin vastaavat pistevoimat.

A Feasibility Study of a Pelleting Plant as an Option for By Product Upgrading in Wood-Processing Industry

Tämän kannattavuustutkimuksen lähtökohtana oli se, että Yhtyneet Sahat Oy:n Kaukaan sahalla ja Luumäen jatkojalostuslaitoksella haluttiin selvittää pellettitehtaan kannattavuus nykyisessä markkinatilanteessa. Tämä työon luonteeltaan teknis-taloudellinen selvitys eli ns. feasibility study. Pelletöintiprosessi on tekniikaltaan yksinkertainen eikä edellytä korkea teknologian laitteita. Toimiala on maailmanlaajuisesti varsin uusi. Suomessa pellettimarkkinat ovat vielä pienet ja kehittymättömät, mutta kasvua on viime vuosina tapahtunut. Valtaosa kotimaan tuotannosta menee vientiin. Investoinnin laskentaprosessissa saadut tuotannon alkuarvot sekä kustannusrakenteen määrittelyt ovat perustana varsinaisille kannattavuuslaskelmille. Laskelmista on selvitetty investointeihin liittyvät yleisimmät taloudelliset tunnusluvut ja herkimpiä muuttujia on tutkittu ja pohdittu herkkyysanalyysiä apuna käyttäen.

Development of rotating drum under mechanical and thermal load

A variable temperature field sets exacting demands to the structure under mechanical load. Most of all the lifetime of the rotating drum structure depends on temperature differences between parts inside the drum. The temperature difference was known because of the measurements made before. The list of demands was created based on customers’ needs. The limits of this paper were set to the inner structure of the drum. Creation of ideas for the inner structure was started open minded. The main principle in the creation process was to create new ideas for the function of the product with the help of sub-functions. The sub-functions were created as independent as possible. The best sub-functions were combined together and the new working principles were created based on them. Every working principle was calculated separately and criticized at the end of the calculation process. The main objective was to create the new kind of structure, which is not based too much to the old, inoperative structure. The affect of own weight of the inner structure to the stress values was quite small but it was also taken into consideration when calculating the maximum stress value of the structure. Because of very complex structures all of the calculations were made with the help of the ProE – Mechanica software. The fatigue analyze was made also for the best structure solution.

Optimizing of intelligence level in welding

The productivity, quality and cost efficiency of welding work are critical for metal industry today. Welding processes must get more effective and this can be done by mechanization and automation. Those systems are always expensive and they have to pay the investment back. In this case it is really important to optimize the needed intelligence and this way needed automation level, so that a company will get the best profit. This intelligence and automation level was earlier classified in several different ways which are not useful for optimizing the process of automation or mechanization of welding. In this study the intelligence of a welding system is defined in a new way to enable the welding system to produce a weld good enough. In this study a new way is developed to classify and select the internal intelligence level of a welding system needed to produce the weld efficiently. This classification contains the possible need of human work and its effect to the weld and its quality but does not exclude any different welding processes or methods. In this study a totally new way is developed to calculate the best optimization for the needed intelligence level in welding. The target of this optimization is the best possible productivity and quality and still an economically optimized solution for several different cases. This new optimizing method is based on grounds of product type, economical productivity, the batch size of products, quality and criteria of usage. Intelligence classification and optimization were never earlier made by grounds of a made product. Now it is possible to find the best type of welding system needed to welddifferent types of products. This calculation process is a universal way for optimizing needed automation or mechanization level when improving productivity of welding. This study helps the industry to improve productivity, quality and cost efficiency of welding workshops.

Virtuaalisen lajittelujärjestelmän hyödyntäminen postipalveluyrityksen tuotannollisessa prosessissa

Työn tavoitteena oli kehittää toimintoperusteista kustannuslaskentaa soveltamalla laskentamalli, jonka avulla on mahdollista tutkia postipalveluyrityksen tuotannollisen prosessin kokonaistuottavuuden kannalta optimaalista tapaa hyödyntää virtuaalista lajittelujärjestelmää. Kimputuksen osalta syntyi teoreettinen laskentamalli, mutta kuljetusyksiköinnin osalta pyrittiin muodostamaan todellista prosessia mahdollisimman hyvin noudattava malli, jonka tuloksia on helppo tutkia erilaisilla kustannus- ja lähetysparametreillä. Virtuaalisen lajittelujärjestelmän tuotannollisen hyödyntämisen ohella työssä oli tarkoitus toteuttaa alustavaa analyysia siitä, millä tapaa järjestelmän avulla voidaan tuottaa myös muuta lisäarvoa postipalvelutuotannolle. Analyysissa havaittiin alustavia hyödyntämismahdollisuuksia palvelutuotannon kuormitussuunnittelun, osoitelaatusidonnaisten toimintojen sekä postiin jätön ja prosessiin ohjauksen osalta. Ottamatta kantaa hyödyntämismahdollisuuksien toteutettavuuteen analyysin keskeinen tulos oli kuitenkin se, että järjestelmän hyödyntämisen osalta tutkimattomia teitä on vielä lukuisia.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Sähkönsiirtoprojektien kustannuslaskennan kehittäminen

Tämän tutkimuksen tarkoituksena oli lisätä tietoa asiakasyrityksen voimajohto- ja sähköasemaliiketoimintayksiköiden tarjouslaskennan nykytilasta, etsiä ongelmakohtia ja kehittää ratkaisuja ongelmiin. Työn tuloksena saatu tieto on kyseisille liiketoimintayksiköille tärkeää tulevaisuuden kannattavuuden ja jatkuvuuden kannalta. Työn alun teoriaosuudessa esitellään Suomen sähkönsiirtojärjestelmä, käydään läpi voimajohto- ja sähköasemarakentamisen perusteet sekä esitellään kirjallisuuskatsaus projektiliiketoiminnasta. Teoriaosuutta hyödynnetään myöhemmissä tarkasteluissa joissa pyrittiin löytämään kustannuslaskennan ongelmia. Tutkimuksen tärkein tavoite oli löytää tämän hetkisen kustannuslaskennan ongelmakohdat. Tutkimukseen sisältyy tarjouslaskentaohjelmiston koekäyttö sekä sen analysointi. Työn lopputuloksena todetaan, ettei tarkasteltu ohjelma ole sopiva voimajohto- tai sähköasematarjouslaskennan toteutukseen. Ohjelma on laskentatarkkuudeltaan hyvä, mutta ohjelman käyttö hidastaa ja vaikeuttaa sekä laskennan että projektin talouden seurannan suorittamista. Lopputuloksissa todetaan myös erinäisiä pienempiä kehityskohteita tarjouslaskennan sujuvoittamiseksi ja sen tarkkuuden parantamiseksi. 

Development of Piping Stress Analysis Guideline for Neste Jacobs' Projects

The aim of this research was to develop a piping stress analysis guideline to be widely used in Neste Jacobs Oy’s domestic and foreign projects. The company’s former guideline to performing stress analysis was partial and lacked important features, which were to be fixed through this research. The development of the guideline was based on literature research and gathering of existing knowledge from the experts in piping engineering. Case study method was utilized by performing stress analysis on an existing project with help of the new guideline. Piping components, piping engineering in process industry, and piping stress analysis were studied in the theory section of this research. Also, the existing piping standards were studied and compared with one another. By utilizing the theory found in literature and the vast experience and know-how collected from the company’s employees, a new guideline for stress analysis was developed. The guideline would be widely used in various projects. The purpose of the guideline was to clarify certain issues such as which of the piping would have to be analyzed, how are different material values determined and how will the results be reported. As a result, an extensive and comprehensive guideline for stress analysis was created. The new guideline more clearly defines formerly unclear points and creates clear parameters to performing calculations. The guideline is meant to be used by both new and experienced analysts and with its aid, the calculation process was unified throughout the whole company’s organization. Case study was used to exhibit how the guideline is utilized in practice, and how it benefits the calculation process.

Welding time models for cost calculations in the early stages of the design process

It is generally accepted that between 70 and 80% of manufacturing costs can be attributed to design. Nevertheless, it is difficult for the designer to estimate manufacturing costs accurately, especially when alternative constructions are compared at the conceptual design phase, because of the lack of cost information and appropriate tools. In general, previous reports concerning optimisation of a welded structure have used the mass of the product as the basis for the cost comparison. However, it can easily be shown using a simple example that the use of product mass as the sole manufacturing cost estimator is unsatisfactory. This study describes a method of formulating welding time models for cost calculation, and presents the results of the models for particular sections, based on typical costs in Finland. This was achieved by collecting information concerning welded products from different companies. The data included 71 different welded assemblies taken from the mechanical engineering and construction industries. The welded assemblies contained in total 1 589 welded parts, 4 257 separate welds, and a total welded length of 3 188 metres. The data were modelled for statistical calculations, and models of welding time were derived by using linear regression analysis. Themodels were tested by using appropriate statistical methods, and were found to be accurate. General welding time models have been developed, valid for welding in Finland, as well as specific, more accurate models for particular companies. The models are presented in such a form that they can be used easily by a designer, enabling the cost calculation to be automated.

Description and implementation of cut calculation-method in a sawmill

Työn tavoitteena oli kuvata ja ottaa käyttöön sahauseräkohtaisen kannattavuuden laskentamenetelmä sahalle, sekä tehdä laskentamalli menetelmän tueksi. Sahauksen peruskäsitteiden jälkeen työssä on esitelty sahan tuotantoprosessi. Tuotantoprosessi on kuvattu kirjallisuuden ja asiantuntijoiden haastattelujen perusteella. Seuraavaksi kartoitettiin hyötyjä ja vaikutuksia, mitä laskentamenetelmältä odotetaan.. Kustannuslaskennan teoriaa selvitettiin kirjallisuuslähteitä käyttäen silmälläpitäen juuri tätä kehitettävää laskentamenetelmää. Lisäksi esiteltiin Uimaharjun sahalla käytettävät ja laskentaan liittyvät laskenta- ja tietojärjestelmät.Nykyisin sahalla ei ole minkäänlaista menetelmää sahauseräkohtaisen tuloksen laskemiseksi. Pienillä muutoksilla sahan tietojärjestelmään ja prosessikoneisiin voidaan sahauserä kuljettaa prosessin läpi niin, että jokaisessa prosessin vaiheessa sille saadaan kohdistettua tuotantotietoa. Eri vaiheista saatua tietoa käyttämällä saadaan tarkasti määritettyä tuotteet, joita sahauserä tuotti ja paljonko tuotantoresursseja tuottamiseen kului. Laskentamalliin syötetään tuotantotietoja ja kustannustietoa ja saadaan vastaukseksi sahauserän taloudellinen tulos.Toimenpide ehdotuksena esitetään lisätutkimusta tuotantotietojen automaattisesta keräämisestä manuaalisen työn ja virheiden poistamiseksi. Suhteellisen pienillä panoksilla voidaan jokaiselle sahauserälle kerätä tuotantotiedot täysin automaattisesti. Lisäksi kehittämäni laskentamallin tilalle tulisi hankkia sovellus, joka käyttäisi paremmin hyväksi nykyisiä tietojärjestelmiä ja poistaisi manuaalisen työvaiheen laskennassa.

Improving the calculation of rate of stratification in APROS

APROS (Advanced Process Simulation Environment) is a computer simulation program developed to simulate thermal hydraulic processes in nuclear and conventional power plants. Earlier research at VTT Technological Research Centre of Finland had found the current version of APROS to produce inaccurate simulation results for a certain case of loop seal clearing. The objective of this Master’s thesis is to find and implement an alternative method for calculating the rate of stratification in APROS, which was found to be the reason for the inaccuracies. Brief literature study was performed and a promising candidate for the new method was found. The new method was implemented into APROS and tested against experiments and simulations from two test facilities and the current version of APROS. Simulation results with the new version were partially conflicting; in some cases the new method was more accurate than the current version, in some the current method was better. Overall, the new method can be assessed as an improvement.

Modelling of calciner in post-combustion carbon capture process

Climate change has given an impetus to research and developed new technologies to reduce significantly carbon dioxide emissions in energy production in the developed countries. The major pollution source, fossil fuels, will be used as an energy source for many decades, which provides the demand for carbon capture and storage technologies. Over recent years many new technologies has been developed and one of the most promising is calcium-looping in post-combustion carbon capture process, which use carbonation-calcination cycle to capture carbon dioxide from the flue gas of a combustion process. First pilot plant for calcium-looping process has been built in Oviedo, Spain. In this study, a three-dimensional model has been created for the calciner, which is one of the two fluidized bed reactors needed for the process. The calciner is a regenerator where the captured carbon dioxide is removed from the calcium material and then collected after the reactor. Thesis concentrates in creating the calciner 3D-model frame with CFB3D-program and testing the model with two different example cases. Used input parameters and calciner geometry are Oviedo pilot plant design parameters. The calculation results give information about the process and show that pilot plant calciner should perform as planned. This Master’s Thesis is done in participation to EU FP7 project CaOling.

Separation of lignin in Pulp Mill process and its effect on sodium sulphur balance

The aim of this thesis is to define effects of lignin separation process on Pulp mill chemical balance especially on sodium/sulphur-balance. The objective is to develop a simulation model with WinGEMS Process Simulator and use that model to simulate the chemical balances and process changes. The literature part explains what lignin is and how kraft pulp is produced. It also introduces to the methods that can be used to extract lignin from black liquor stream and how those methods affect the pulping process. In experimental part seven different cases are simulated with the created simulation model. The simulations are based on selected reference mill that produces 500 000 tons of bleached air-dried (90 %) pulp per year. The simulations include the chemical balance calculation and the estimated production increase. Based on the simulations the heat load of the recovery boiler can be reduced and the pulp production increased when lignin is extracted. The simulations showed that decreasing the waste acid stream intake from the chlorine dioxide plant is an effective method to control the sulphidity level when about 10 % of lignin is extracted. With higher lignin removal rates the in-mill sulphuric acid production has been discovered to be a better alternative to the sulphidity control.