Wet Oxidation of Concentrated Wastewaters: Process Combination and Reaction Kinetic Modeling

The accumulation of aqueous pollutants is becoming a global problem. The search for suitable methods and/or combinations of water treatment processes is a task that can slow down and stop the process of water pollution. In this work, the method of wet oxidation was considered as an appropriate technique for the elimination of the impurities present in paper mill process waters. It has been shown that, when combined with traditional wastewater treatment processes, wet oxidation offers many advantages. The combination of coagulation and wet oxidation offers a new opportunity for the improvement of the quality of wastewater designated for discharge or recycling. First of all, the utilization of coagulated sludge via wet oxidation provides a conditioning process for the sludge, i.e. dewatering, which is rather difficult to carry out with untreated waste. Secondly, Fe2(SO4)3, which is employed earlier as a coagulant, transforms the conventional wet oxidation process into a catalytic one. The use of coagulation as the post-treatment for wet oxidation can offer the possibility of the brown hue that usually accompanies the partial oxidation to be reduced. As a result, the supernatant is less colored and also contains a rather low amount of Fe ions to beconsidered for recycling inside mills. The thickened part that consists of metal ions is then recycled back to the wet oxidation system. It was also observed that wet oxidation is favorable for the degradation of pitch substances (LWEs) and lignin that are present in the process waters of paper mills. Rather low operating temperatures are needed for wet oxidation in order to destruct LWEs. The oxidation in the alkaline media provides not only the faster elimination of pitch and lignin but also significantly improves the biodegradable characteristics of wastewater that contains lignin and pitch substances. During the course of the kinetic studies, a model, which can predict the enhancements of the biodegradability of wastewater, was elaborated. The model includes lumped concentrations suchas the chemical oxygen demand and biochemical oxygen demand and reflects a generalized reaction network of oxidative transformations. Later developments incorporated a new lump, the immediately available biochemical oxygen demand, which increased the fidelity of the predictions made by the model. Since changes in biodegradability occur simultaneously with the destruction of LWEs, an attempt was made to combine these two facts for modeling purposes.

Wet Oxidation of TMP Concentrated Paper Mill Process Water. Kinetics of the reaction

Työn tarkoituksena oli tutkia lämpötilan, paineen, pH:n ja katalyytin vaikutusta paperitehtaan TMP-konsentroidun prosessiveden märkähapetuksessa. Teoriaosio sisältää katsauksen sellu- ja paperiteollisuuteen, jätevesien käsittelyyn, nanosuodatuksen ja märkähapetusprosessin toimintaperiaatteet ja sovellukset hybriditeknologialle nanosuodatus-märkähapetuksessa. Empiirinen osa koostuu märkähapetuskokeista eri lämpötiloissa, paineissa, pH:ssa ja eri katalyyseillä. Työssä tutkittiin näiden vaikutusta kemialliseen hapenkulutukseen (COD), Biologiseen hapenkulutukseen (BOD), Välittömästi saatavana olevan biologisen hapenkulutukseen (IABOD), ligniiniin, täysin orgaanisen hiileen (TOC) ja rasvaliukoisten uuteaineiden (LWEs) pitoisuuteen. Tuloksina kokeellisesta työstä saatiin korkeimmat COD:n alenemat ja BOD/COD (biohajoavuus) suurimmilla lämpötilaolosuhteilla (COD:n alenema 70 % ja BOD/COD 97 % 200 °C:ssa ja hapen 10 bar osapaineella). Tutkimuksessa, jossa selvitettiin hapen osapaineen vaikutusta saatiin tuloksena, että hapen osapaineen kasvu parantaa orgaanisen kuormituksen poistoa: COD poisto oli olosuhteilla130°C, 5bar 5 %, olosuhteilla 130 °C, 15bar 15 %, olosuhteilla 170 °C, 5bar 20 % ja olosuhteilla 170 °C, 15bar 50 %. Lähes täydellinen LWEs –poisto saavutettiin 150 °C ja 10bar olosuhteilla, vaikka tässä lämpötilassa ei saavutettu korkeata orgaanisen kuormituksen poistoa. Emäksinen pH vaikutti suosivan hapettavia reaktioita, koska korkein COD:n poisto saavutettiin näissä olosuhteilla; kuitenkin alkalisen väliaineen tehokkuudelle löydettiin tärkeä lämpötilariippuvuus.

Validation of plant dynamic model by online and laboratory measurements – a tool to predict online COD loads out of production of mechanical printing papers

COD discharges out of processes have increased in line with elevating brightness demands for mechanical pulp and papers. The share of lignin-like substances in COD discharges is on average 75%. In this thesis, a plant dynamic model was created and validated as a means to predict COD loading and discharges out of a mill. The assays were carried out in one paper mill integrate producing mechanical printing papers. The objective in the modeling of plant dynamics was to predict day averages of COD load and discharges out of mills. This means that online data, like 1) the level of large storage towers of pulp and white water 2) pulp dosages, 3) production rates and 4) internal white water flows and discharges were used to create transients into the balances of solids and white water, referred to as “plant dynamics”. A conversion coefficient was verified between TOC and COD. The conversion coefficient was used for predicting the flows from TOC to COD to the waste water treatment plant. The COD load was modeled with similar uncertainty as in reference TOC sampling. The water balance of waste water treatment was validated by the reference concentration of COD. The difference of COD predictions against references was within the same deviation of TOC-predictions. The modeled yield losses and retention values of TOC in pulping and bleaching processes and the modeled fixing of colloidal TOC to solids between the pulping plant and the aeration basin in the waste water treatment plant were similar to references presented in literature. The valid water balances of the waste water treatment plant and the reduction model of lignin-like substances produced a valid prediction of COD discharges out of the mill. A 30% increase in the release of lignin-like substances in the form of production problems was observed in pulping and bleaching processes. The same increase was observed in COD discharges out of waste water treatment. In the prediction of annual COD discharge, it was noticed that the reduction of lignin has a wide deviation from year to year and from one mill to another. This made it difficult to compare the parameters of COD discharges validated in plant dynamic simulation with another mill producing mechanical printing papers. However, a trend of moving from unbleached towards high-brightness TMP in COD discharges was valid.

Impact of unsymmetrical loads in distribution networks

Since it is virtually impossible to balance loads in three-phase system, unbalance in a varying degree exists almost in all distribution networks. The aim of the thesis is to analyze the impact of this unbalance subject to different configurations of distribution system and winding connection of the supplying transformer. Also impact of the voltage unbalance on the equipment is investigated. In order to make the investigation more visual, the following calculations have been conducted: - Unsymmetrical load in four-wire star connected network - Unsymmetrical load in four-wire star connected network with broken zero conductor (or three-wire network). - Unsymmetrical load when the supplying transformer is so-called zigzag transformer. PDF created

Imatran tehtaiden jätevesipäästöjen hallinta- ja analysointityökalun kehittäminen

Työn tavoitteena oli kehittää Stora Enso Oyj:n Imatran tehtaille Wedge-pohjainen analysointityökalu, jolla voidaan hallita prosessi- ja päästötietojen yhteys nykyistä paremmin. Wedgeen määriteltiin päästömittauksia, olennaisia prosessimittauksia ja tarpeelliset laskennat kuormituksen ennustamiseksi lähtien tuotantoprosessien tilasta. Työssä tehtiin kemialliselle ja biologiselle jätevedenpuhdistamolle meneville jätevesille laskennallisia malleja, joita verrattiin mitattuihin arvoihin. Kemialliselle jätevedenpuhdistamolle meneville jätevesille tehtiin malli jäteveden virtaamalle. Biologiselle jätevedenpuhdistamolle meneville jätevesille tehtiin mallit jäteveden virtaamalle sekä COD-, AOX- ja alkuainekuormituksille. Alkuaineista työhön otettiin mukaan natrium, rikki ja kloori. Teoriaosassa on käsitelty sellu- ja paperitehtaiden vedenkäyttöä, tehtaan eri osastojen jätevesikuormitusta, jäteveden puhdistusmenetelmiä sekä prosessidatan käsittelymenetelmiä. Kokeellisessa osassa on esitelty mitattujen ja laskennallisten mallien yhteyttä. Suurin osa laskennallisista malleista näyttää seuraavan kohtuullisen hyvin mitattuja arvoja. Kokeellisessa osassa on myös havainnollistettu esimerkkien avulla mallien hyödyntämistä. Työn hyötynä on normaalien kuormitusvaihteluiden ja häiriöpäästöjen entistä tarkempi ja nopeampi erottelu. Pitkällä tähtäimellä Wedge-ohjelman avulla pystytään keskittämään jätevesikuormituksen vähentämistoimenpiteet olennaisimpiin kohteisiin.

Concentrated Winding Multiphase Permanent Magnet Machine Design and Electromagnetic Properties – Case Axial Flux Machine

Concentrated winding permanent magnet machines and their electromagnetic properties are studied in this doctoral thesis. The thesis includes a number of main tasks related to the application of permanent magnets in concentrated winding open slot machines. Suitable analytical methods are required for the first design calculations of a new machine. Concentrated winding machines differ from conventional integral slot winding machines in such a way that adapted analytical calculation methods are needed. A simple analytical model for calculating the concentrated winding axial flux machines is provided. The next three main design tasks are discussed in more detail in the thesis. The magnetic length of the rotor surface magnet machines is studied, and it is shown that the traditional methods have to be modified also in this respect. An important topic in this study has been to evaluate and minimize the rotor permanent magnet Joule losses by using segmented magnets in the calculations and experiments. Determination of the magnetizing and leakage inductances for a concentrated winding machine and the torque production capability of concentrated winding machines with different pole pair numbers are studied, and the results are compared with the corresponding properties of integral slot winding machines. The thesis introduces a new practical permanent magnet motor type for industrial use. The special features of the machine are based on the option of using concentrated winding open slot constructions of permanent magnet synchronous machines in the normal speed ranges of industrial motors, for instance up to 3000 min-1, without excessive rotor losses. By applying the analytical equations and methods introduced in the thesis, a 37 kW 2400 min-1 12-slot 10-pole axial flux machine with rotor-surfacemounted magnets is designed. The performance of the designed motor is determined by experimental measurements and finite element calculations.

Optimization of parameters for fiber laser-MAG hybrid welding in shipbuilding applications

The Arctic region becoming very active area of the industrial developments since it may contain approximately 15-25% of the hydrocarbon and other valuable natural resources which are in great demand nowadays. Harsh operation conditions make the Arctic region difficult to access due to low temperatures which can drop below -50 °C in winter and various additional loads. As a result, newer and modified metallic materials are implemented which can cause certain problems in welding them properly. Steel is still the most widely used material in the Arctic regions due to high mechanical properties, cheapness and manufacturability. Moreover, with recent steel manufacturing development it is possible to make up to 1100 MPa yield strength microalloyed high strength steel which can be operated at temperatures -60 °C possessing reasonable weldability, ductility and suitable impact toughness which is the most crucial property for the Arctic usability. For many years, the arc welding was the most dominant joining method of the metallic materials. Recently, other joining methods are successfully implemented into welding manufacturing due to growing industrial demands and one of them is the laser-arc hybrid welding. The laser-arc hybrid welding successfully combines the advantages and eliminates the disadvantages of the both joining methods therefore produce less distortions, reduce the need of edge preparation, generates narrower heat-affected zone, and increase welding speed or productivity significantly. Moreover, due to easy implementation of the filler wire, accordingly the mechanical properties of the joints can be manipulated in order to produce suitable quality. Moreover, with laser-arc hybrid welding it is possible to achieve matching weld metal compared to the base material even with the low alloying welding wires without excessive softening of the HAZ in the high strength steels. As a result, the laser-arc welding methods can be the most desired and dominating welding technology nowadays, and which is already operating in automotive and shipbuilding industries with a great success. However, in the future it can be extended to offshore, pipe-laying, and heavy equipment industries for arctic environment. CO2 and Nd:YAG laser sources in combination with gas metal arc source have been used widely in the past two decades. Recently, the fiber laser sources offered high power outputs with excellent beam quality, very high electrical efficiency, low maintenance expenses, and higher mobility due to fiber optics. As a result, fiber laser-arc hybrid process offers even more extended advantages and applications. However, the information about fiber or disk laser-arc hybrid welding is very limited. The objectives of the Master’s thesis are concentrated on the study of fiber laser-MAG hybrid welding parameters in order to understand resulting mechanical properties and quality of the welds. In this work only ferrous materials are reviewed. The qualitative methodological approach has been used to achieve the objectives. This study demonstrates that laser-arc hybrid welding is suitable for welding of many types, thicknesses and strength of steels with acceptable mechanical properties along very high productivity. New developments of the fiber laser-arc hybrid process offers extended capabilities over CO2 laser combined with the arc. This work can be used as guideline in hybrid welding technology with comprehensive study the effect of welding parameter on joint quality.

Comparison of Different Concentrated Solar Power Collector Designs and Development of a Linear Fresnel Solar Collector Model

Concentrated solar power (CSP) is a renewable energy technology, which could contribute to overcoming global problems related to pollution emissions and increasing energy demand. CSP utilizes solar irradiation, which is a variable source of energy. In order to utilize CSP technology in energy production and reliably operate a solar field including thermal energy storage system, dynamic simulation tools are needed in order to study the dynamics of the solar field, to optimize production and develop control systems. The object of this Master’s Thesis is to compare different concentrated solar power technologies and configure a dynamic solar field model of one selected CSP field design in the dynamic simulation program Apros, owned by VTT and Fortum. The configured model is based on German Novatec Solar’s linear Fresnel reflector design. Solar collector components including dimensions and performance calculation were developed, as well as a simple solar field control system. The preliminary simulation results of two simulation cases under clear sky conditions were good; the desired and stable superheated steam conditions were maintained in both cases, while, as expected, the amount of steam produced was reduced in the case having lower irradiation conditions. As a result of the model development process, it can be concluded, that the configured model is working successfully and that Apros is a very capable and flexible tool for configuring new solar field models and control systems and simulating solar field dynamic behaviour.