Influence of stationary phase and eluent properties on chromatographic separation of carbohydrates

In this thesis, the sorption and elastic properties of the cation-exchange resins were studied to explain the liquid chromatographic separation of carbohydrates. Na+, Ca2+ and La3+ form strong poly(styrene-co-divinylbenzene) (SCE) as well as Na+ and Ca2+ form weak acrylic (WCE) cation-exchange resins at different cross-link densities were treated within this work. The focus was on the effects of water-alcohol mixtures, mostly aqueous ethanol, and that of the carbohydrates. The carbohydrates examined were rhamnose, xylose, glucose, fructose, arabinose, sucrose, xylitol and sorbitol. In addition to linear chromatographic conditions, non-linear conditions more typical for industrial applications were studied. Both experimental and modeling aspectswere covered. The aqueous alcohol sorption on the cation-exchangers were experimentally determined and theoretically calculated. The sorption model includes elastic parameters, which were obtained from sorption data combined with elasticity measurements. As hydrophilic materials cation-exchangers are water selective and shrink when an organic solvent is added. At a certain deswelling degree the elastic resins go through glass transition and become as glass-like material. Theincreasing cross-link level and the valence of the counterion decrease the sorption of solvent components in the water-rich solutions. The cross-linkage or thecounterions have less effect on the water selectivity than the resin type or the used alcohol. The amount of water sorbed is higher in the WCE resin and, moreover, the WCE resin is more water selective than the corresponding SCE resin. Theincreased aliphatic part of lower alcohols tend to increase the water selectivity, i.e. the resins are more water selective in 2-propanol than in ethanol solutions. Both the sorption behavior of carbohydrates and the sorption differences between carbohydrates are considerably affected by the eluent composition and theresin characteristics. The carbohydrate sorption was experimentally examined and modeled. In all cases, sorption and moreover the separation of carbohydrates are dominated by three phenomena: partition, ligand exchange and size exclusion. The sorption of hydrophilic carbohydrates increases when alcohol is added into the eluent or when carbohydrate is able to form coordination complexes with the counterions, especially with multivalent counterions. Decreasing polarity of the eluent enhances the complex stability. Size exclusion effect is more prominent when the resin becomes tighter or carbohydrate size increases. On the other hand,the elution volumes between different sized carbohydrates decreases with the decreasing polarity of the eluent. The chromatographic separation of carbohydrateswas modeled, using rhamnose and xylose as target molecules. The thermodynamic sorption model was successfully implemented in the rate-based column model. The experimental chromatographic data were fitted by using only one adjustable parameter. In addition to the fitted data also simulated data were generated and utilized in explaining the effect of the eluent composition and of the resin characteristics on the carbohydrate separation.

Ion-exchange resins as stationary phase in reactive chromatography

Dynamic behavior of bothisothermal and non-isothermal single-column chromatographic reactors with an ion-exchange resin as the stationary phase was investigated. The reactor performance was interpreted by using results obtained when studying the effect of the resin properties on the equilibrium and kinetic phenomena occurring simultaneously in the reactor. Mathematical models were derived for each phenomenon and combined to simulate the chromatographic reactor. The phenomena studied includes phase equilibria in multicomponent liquid mixture¿ion-exchange resin systems, chemicalequilibrium in the presence of a resin catalyst, diffusion of liquids in gel-type and macroporous resins, and chemical reaction kinetics. Above all, attention was paid to the swelling behavior of the resins and how it affects the kinetic phenomena. Several poly(styrene-co-divinylbenzene) resins with different cross-link densities and internal porosities were used. Esterification of acetic acid with ethanol to produce ethyl acetate and water was used as a model reaction system. Choosing an ion-exchange resin with a low cross-link density is beneficial inthe case of the present reaction system: the amount of ethyl acetate as well the ethyl acetate to water mole ratio in the effluent stream increase with decreasing cross-link density. The enhanced performance of the reactor is mainly attributed to increasing reaction rate, which in turn originates from the phase equilibrium behavior of the system. Also mass transfer considerations favor the use ofresins with low cross-link density. The diffusion coefficients of liquids in the gel-type ion-exchange resins were found to fall rapidly when the extent of swelling became low. Glass transition of the polymer was not found to significantlyretard the diffusion in sulfonated PS¿DVB ion-exchange resins. It was also shown that non-isothermal operation of a chromatographic reactor could be used to significantly enhance the reactor performance. In the case of the exothermic modelreaction system and a near-adiabatic column, a positive thermal wave (higher temperature than in the initial state) was found to travel together with the reactive front. This further increased the conversion of the reactants. Diffusion-induced volume changes of the ion-exchange resins were studied in a flow-through cell. It was shown that describing the swelling and shrinking kinetics of the particles calls for a mass transfer model that explicitly includes the limited expansibility of the polymer network. A good description of the process was obtained by combining the generalized Maxwell-Stefan approach and an activity model that was derived from the thermodynamics of polymer solutions and gels. The swelling pressure in the resin phase was evaluated by using a non-Gaussian expression forthe polymer chain length distribution. Dimensional changes of the resin particles necessitate the use of non-standard mathematical tools for dynamic simulations. A transformed coordinate system, where the mass of the polymer was used as a spatial variable, was applied when simulating the chromatographic reactor columns as well as the swelling and shrinking kinetics of the resin particles. Shrinking of the particles in a column leads to formation of dead volume on top of the resin bed. In ordinary Eulerian coordinates, this results in a moving discontinuity that in turn causes numerical difficulties in the solution of the PDE system. The motion of the discontinuity was eliminated by spanning two calculation grids in the column that overlapped at the top of the resin bed. The reactive and non-reactive phase equilibrium data were correlated with a model derived from thethermodynamics of polymer solution and gels. The thermodynamic approach used inthis work is best suited at high degrees of swelling because the polymer matrixmay be in the glassy state when the extent of swelling is low.

Antitromboottisten lääkeaineiden enantiomeerien kromatografinen fraktiointi

Suuri osa käytössä olevista lääkeaineista on kiraalisia yhdisteitä. Lääkevalmisteet sisältävät yhdisteen enantiomeerien ominaisuuksista riippuen joko yksittäistä enantiomeeria tai näiden seosta. Antitromboottisiin eli veren hyytymistä estäviin lääkeaineisiin kuuluvat varfariini ja rivaroksabaani ovat kiraalisia yhdisteitä, joiden enantiomeerien ominaisuudet poikkeavat antitromboottisen vaikutuksen voimakkuuden suhteen. Varfariinia käytetään kliinisesti enantiomeeriensa raseemisena seoksena, kun taas rivaroksabaani on käytössä lääkevalmisteena puhtaana S-enantiomeerinaan. Lääkeaineen enantiomeerien erottaminen toisistaan on tärkeää esimerkiksi enantiomeerien puhdistamiseksi, lääkevalmisteen oikean koostumuksen varmistamiseksi tai yksittäisten enantiomeerien käyttäytymisen arvioimiseksi elimistössä. Tässä kirjallisuustyössä käsiteltiin nestekromatografian käyttöä antitromboottisiin lääkeaineisiin kuuluvien antikoagulanttien enantiomeerien fraktioinnissa. Kirjallisuudesta saadun tiedon perusteella arvioitiin, millä erotusmateriaaleilla ja millaisissa koeolosuhteissa varfariinin sekä rivaroksabaanin enantiomeerit tulisi erottaa toisistaan. Varfariinin enantiomeerien erotukseen parhaiten sopivaksi erotusmateriaaliksi todettiin kirjallisuuden perusteella kiraalinen vankomysiinipohjainen stationaarifaasi (Chirobiotic V) metanolin, etikkahapon ja veden seoksen toimiessa eluenttina. Eluentin virtausnopeudella 0,3 mL/min ja pienellä injektiotilavuudella varfariinin enantiomeerit saatiin erottumaan täydellisesti ja nopeasti toisistaan. Kirjallisuuden perusteella rivaroksabaanin enantiomeerien erotuksessa erotusmateriaalina toimii parhaiten kiraalinen selluloosapohjainen stationaarifaasi (Chiralcel OD-RH), kun eluenttina käytetään n-heksaanin ja isopropanolin seosta virtausnopeudella 1 mL/min. Varfariinin ja rivaroksabaanin enantiomeerien fraktiointiin parhaiten sopivia menetelmiä voidaan käyttää eri tilanteissa, kuten lääkevalmisteiden laadunvarmistuksessa tai enantiomeerien erotuksessa niiden synteesin jälkeen.

Aminohappojen enantiomeerien kromatografinen erottaminen

Enantiomeerit ovat yhdisteitä, jotka ovat toistensa peilikuvamuotoja. Enantiomeerien erotusmenetelmiä ovat neste-nesteuutto, kalvotekniikka, kiteytys, kromatografia ja kapillaarielektroforeesi. Nestekromatografinen erotus perustuu joko suoraan erotukseen tai epäsuoraan erotukseen. Kiraaliset stationaarifaasit erottavat yhdisteet kolonnissa suoralla erotuksella. Derivoimattomia aminohappojen enantiomeerejä on erotettu käyttäen ligandinvaihto-, kruunueetteri-, antibiootti- ja polysakkaridistationaarifaaseja. Epäsuora erotus vaatii erotettavan enantiomeeriparin esikäsittelyn ennen kolonnia. Markkinoilta löytyy niukasti preparatiiviseen mittakaavaan soveltuvia enantiomeerien erotusmateriaaleja. Työn kokeellisessa osassa enantiomeerien erotuksia tehtiin sekä analyyttisessä mittakaavassa että preparatiivisessa mittakaavassa. Tutkittavina pääkomponentteina aminohapoista olivat metioniinin, proliinin ja seriinin enantiomeeriparit. Analyyttisessä mittakaavassa kuparimuotoisella ligandinvaihtokolonnilla tehty erotus onnistui erittäin hyvin. Piikkien resoluutioiden arvot vaihtelivat tyypillisesti välillä 2,0-35 ja erotustekijöiden arvot välillä 1,5-30. Parhaiten onnistuttiin erottamaan metioniinin enantiomeerit toisistaan. Prepatatiivisen mittakaavan erotusmateriaalin tutkimus keskittyi materiaalin kokeiluun ja kehitykseen aminohappojen enantiomeerien erotukseen soveltuvaksi. Erotusmateriaalilla onnistuttiin erottamaan aminohappoja toisistaan, mutta aminohappojen enantiomeerien erottumista ei onnistuttu selkeästi havaitsemaan. Erotusmateriaali toimi parhaiten muunnettuna alkaalisissa olosuhteissa kuparimuotoiseksi. Kuparin pysymättömyys erotusmateriaalissa aiheutti kuitenkin ongelmia kokeiden toistettavuuteen.

Koboltin ja nikkelin poisto sinkkisulfaattiliuoksesta ioninvaihdolla

Työssä tutkittiin kahden silikapohjaisen erotusmateriaalin soveltuvuutta nikkelin ja koboltin poistoon sinkkisulfaattiliuoksista. Suurin osa kokeista tehtiin ioninvaihtimella, jonka funktionaalinen ryhmä on iminodietikkahappo. Vertailuerotusmateriaalin toiminta perustui adsorptioon. Liuoksina käytettiin sekä autenttista prosessiliuosta että synteettistä ZnSO4-liousta. Ioninvaihtimen kestävyyskokeissa selvisi, että tutkittu ioninvaihdin kestää hyvin sekä 60 oC lämpötilan että happamia olosuhteita. Emäksisissä liuoksissa silikarunko ei kestä. Jo 0,1 M NaOH-liuos liuottaa merkittävästi hartsia vuorokauden aikana. Vaihtimen vetyionikapasiteetiksi saatiin titrauksella 2,3 mekv/g. Tasapainokokeilla saatiin selville, että ioninvaihdin on selektiivinen nikkelille sinkin suhteen ja että selektiivisyys kasvaa liuoksen pH:n laskiessa. Koboltille ioninvaihdin ei ole selektiivinen sinkin suhteen. Mikäli sinkin pitoisuus on tuhansia kertoja nikkelin pitoisuutta suurempi, ei ioninvaihtimen Ni-selektiivisyys riitä myöskään nikkelille. Synteettisillä ZnSO4-liuoksilla tehtyjen kolonnikokeiden perusteella havaittiin, että tutkitulla ioninvaihtimella voidaan laimeista ZnSO4-liuoksista poistaa nikkeliä selektiivisesti. Nikkelin eluointi onnistui helposti 1 M H2SO4:lla. Vertailukokeen perusteella oli ioninvaihtimen Ni/Zn-selektiivisyys referenssiadsorbentin Ni/Zn-selektiivisyyttä pienempi. Ioninvaihtokolonnin mallintaminen ei onnistunut riittävän hyvin kuvaamaan ioninvaihtimessa tapahtuvaa samanaikaista ioninvaihtoa ja adsorptiota. Sen sijaan kun kolonnissa oli vertailumateriaalina käytetty adsorbentti, saatiin kolonnikokeiden tulokset mallilla hyvin ennustettua.

Polymeeriadsorbenttien käyttö kromatografisessa erotuksessa

Polymeeriadsorbentteja valmistetaan silloittamalla styreeniä, akrylaattia tai fenoliformaldehydiä. Useimmiten ristisilloittajana toimii divinyylibentseeni. Polymeeriadsorbenteissa ei itsessään ole ioninvaihtoryhmiä, joten ne sopivat ionittomien ja heikosti ionisoitujen aineiden adsorptioon. Usein polymeeriadsorbentteja käytetään vaihtoehtona aktiivihiilelle eri sovelluksissa. Työn kirjallisuusosassa on katsaus polymeeriadsorbenttien sovelluksiin lähinnä elintarviketeollisuudessa. Lisäksi siinä selvitetään polymeeriadsorbenttien rakennetta ja synteesimenetelmiä. Kokeellisessa osassa tutkittiin valittujen styreeni- ja akrylaattipohjaisten polymeeriadsorbenttien soveltuvuutta kromatografisen erotuksen stationaarifaasiksi. Kromatografia-ajoissa käytettiin eluenttina vettä, jonka lämpötila oli pääasiassa joko 75 tai 125 °C. Jälkimmäisessä lämpötilassa vesi on paineistettua neste, jota kutsutaan myös alikriittiseksi vedeksi. Malliaineina oli eri sokereita, aminohappoja sekä bentsoehappoa ja bentsyylialkoholia. Kromatografisen soveltuvuuden lisäksi selvitettiin adsorbenttien termistä kestävyyttä ja rakennetta. Termisesti polymeeriadsorbentit kestivät hyvin lämpötiloja 125 °C:eseen saakka. Polymeeriadsorbenteilla, joilla on suuri ominaispinta-ala, on myös suuri adsorptiokapasiteetti. Styreenipohjaiset adsorbentit erottivat kaikkia tutkittuja malliaineita akrylaattipohjaisia paremmin. Jotkut adsorbentit eivät erottaneet mitään tutkituista yhdisteistä. Lämpötilan nostaminen kavensi piikkejä ja nopeutti malliaineiden retentoitumista, mutta ei parantanut erottumista.

Improvements in the Assessment of Bacterial Viability and Killing

It is axiomatic that our planet is extensively inhabited by diverse micro-organisms such as bacteria, yet the absolute diversity of different bacterial species is widely held to be unknown. Different bacteria can be found from the depths of the oceans to the top of the mountains; even the air is more or less colonized by bacteria. Most bacteria are either harmless or even advantageous to human beings but there are also bacteria, which can cause severe infectious diseases or spoil the supplies intended for human consumption. Therefore, it is vitally important not only to be able to detect and enumerate bacteria but also to assess their viability and possible harmfulness. Whilst the growth of bacteria is remarkably fast under optimum conditions and easy to detect by cultural methods, most bacteria are believed to lie in stationary phase of growth in which the actual growth is ceased and thus bacteria may simply be undetectable by cultural techniques. Additionally, several injurious factors such as low and high temperature or deficiency of nutrients can turn bacteria into a viable but non-culturable state (VBNC) that cannot be detected by cultural methods. Thereby, various noncultural techniques developed for the assessment of bacterial viability and killing have widely been exploited in modern microbiology. However, only a few methods are suitable for kinetic measurements, which enable the real-time detection of bacterial growth and viability. The present study describes alternative methods for measuring bacterial viability and killing as well as detecting the effects of various antimicrobial agents on bacteria on a real-time basis. The suitability of bacterial (lux) and beetle (luc) luciferases as well as green fluorescent protein (GFP) to act as a marker of bacterial viability and cell growth was tested. In particular, a multiparameter microplate assay based on GFP-luciferase combination as well as a flow cytometric measurement based on GFP-PI combination were developed to perform divergent viability analyses. The results obtained suggest that the antimicrobial activities of various drugs against bacteria could be successfully measured using both of these methods. Specifically, the data reliability of flow cytometric viability analysis was notably improved as GFP was utilized in the assay. A fluoro-luminometric microplate assay enabled kinetic measurements, which significantly improved and accelerated the assessment of bacterial viability compared to more conventional viability assays such as plate counting. Moreover, the multiparameter assay made simultaneous detection of GFP fluorescence and luciferase bioluminescence possible and provided extensive information about multiple cellular parameters in single assay, thereby increasing the accuracy of the assessment of the kinetics of antimicrobial activities on target bacteria.

Chromatographic recovery of chemicals from acidic biomass hydrolysates

Lignocellulosic biomasses (e.g., wood and straws) are a potential renewable source for the production of a wide variety of chemicals that could be used to replace those currently produced by petrochemical industry. This would lead to lower greenhouse gas emissions and waste amounts, and to economical savings. There are many possible pathways available for the manufacturing of chemicals from lignocellulosic biomasses. One option is to hydrolyze the cellulose and hemicelluloses of these biomasses into monosaccharides using concentrated sulfuric acid as catalyst. This process is an efficient method for producing monosaccharides which are valuable platforn chemicals. Also other valuable products are formed in the hydrolysis. Unfortunately, the concentrated acid hydrolysis has been deemed unfeasible mainly due to high chemical consumption resulting from the need to remove sulfuric acid from the obtained hydrolysates prior to the downstream processing of the monosaccharides. Traditionally, this has been done by neutralization with lime. This, however, results in high chemical consumption. In addition, the by-products formed in the hydrolysis are not removed and may, thus, hinder the monosaccharide processing. In order to improve the feasibility of the concentrated acid hydrolysis, the chemical consumption should be decreased by recycling of sulfuric acid without neutralization. Furthermore, the monosaccharides and the other products formed in the hydrolysis should be recovered selectively for efficient downstream processing. The selective recovery of the hydrolysis by-products would have additional economical benefits on the process due to their high value. In this work, the use of chromatographic fractionation for the recycling of sulfuric acid and the selective recovery of the main components from the hydrolysates formed in the concentrated acid hydrolysis was investigated. Chromatographic fractionation based on the electrolyte exclusion with gel type strong acid cation exchange resins in acid (H+) form as a stationary phase was studied. A systematic experimental and model-based study regarding the separation task at hand was conducted. The phenomena affecting the separation were determined and their effects elucidated. Mathematical models that take accurately into account these phenomena were derived and used in the simulation of the fractionation process. The main components of the concentrated acid hydrolysates (sulfuric acid, monosaccharides, and acetic acid) were included into this model. Performance of the fractionation process was investigated experimentally and by simulations. Use of different process options was also studied. Sulfuric acid was found to have a significant co-operative effect on the sorption of the other components. This brings about interesting and beneficial effects in the column operations. It is especially beneficial for the separation of sulfuric acid and the monosaccharides. Two different approaches for the modelling of the sorption equilibria were investigated in this work: a simple empirical approach and a thermodynamically consistent approach (the Adsorbed Solution theory). Accurate modelling of the phenomena observed in this work was found to be possible using the simple empirical models. The use of the Adsorbed Solution theory is complicated by the nature of the theory and the complexity of the studied system. In addition to the sorption models, a dynamic column model that takes into account the volume changes of the gel type resins as changing resin bed porosity was also derived. Using the chromatography, all the main components of the hydrolysates can be recovered selectively, and the sulfuric acid consumption of the hydrolysis process can be lowered considerably. Investigation of the performance of the chromatographic fractionation showed that the highest separation efficiency in this separation task is obtained with a gel type resin with a high crosslinking degree (8 wt. %); especially when the hydrolysates contain high amounts of acetic acid. In addition, the concentrated acid hydrolysis should be done with as low sulfuric acid concentration as possible to obtain good separation performance. The column loading and flow rate also have large effects on the performance. In this work, it was demonstrated that when recycling of the fractions obtained in the chromatographic fractionation are recycled to preceding unit operations these unit operations should included in the performance evaluation of the fractionation. When this was done, the separation performance and the feasibility of the concentrated acid hydrolysis process were found to improve considerably. Use of multi-column chromatographic fractionation processes, the Japan Organo process and the Multi-Column Recycling Chromatography process, was also investigated. In the studied case, neither of these processes could compete with the single-column batch process in the productivity. However, due to internal recycling steps, the Multi-Column Recycling Chromatography was found to be superior to the batch process when the product yield and the eluent consumption were taken into account.

Covariant Phase Observables in Quantum Mechanics

The aim of this thesis is to present a solution to the quantum phase problem of the single-mode optical field. The solution is based on the use of phase shift covariant normalized positive operator measures. These measures describe realistic direct coherent state phase measurements such as the phase measurement schemes based on eight-port homodyne detection or heterodyne detection. The structure of covariant operator measures and, more generally, covariant sesquilinear form measures is analyzed in this work. Four different characterizations for phase shift covariant normalized positive operator measures are presented. The canonical covariant operator measure is definded and its properties are studied. Finally, some other suggested phase theories are introduced to investigate their connections to the covariant sesquilinear form measures.