Suffering and the ways of being human : an interview with Arthur Kleinman

Artikkelin tekijämerkintönä virheellisesti Johan Lindqvist

Design of adjustable packaging line

Diplomityön tavoite oli tutkia, mitä toimintoja ja tekniikoita uusi, joustava kartonkipakkauslinja sisältää ja mitkä suuntaukset pakkausteollisuudessa tulevat olemaan tärkeitä tulevaisuudessa. Pakkauslinjan päätoimintoja tarkasteltiin nykyisten jatulevaisuuden tekniikoiden pohjalta. Erityisesti tarkasteltiin laser-sovellusten käytön mahdollisuutta pakkauslinjan eri osatoiminnoissa. Katsaus pakkausteollisuuden tulevaisuuden näkymiin luotiin kirjallisuuden ja aikaisempien tutkimusten pohjalta, minkä perusteella työssä oletetaan, että yksilölliset ja monitoimipakkaukset tulevat lisääntymään tulevaisuudessa. Eri tuotantoerien välillä olevat asetusajat tulee saada minimoitua, mutta millä keinoin joustavuus on saavutettavissa? Yksi ratkaisu pakkausten valmistamisessa on käyttää robottisolua, mikä on mahdollista luultavasti ainakin kuppimuotoisten pakkausten kohdalla. Muutenkin robotiikka on lisääntymässä pakkausteollisuudessa. Digitaalisten painotekniikoiden kehitys on mahdollistanut yksilölliset painatukset. Tulevaisuudessa painatus on mahdollista tehdä pakkauslinjan loppupäässä, jopa vasta täytön ja suljennan jälkeen. Laserleikkaus on jo nyt käytössä, mutta tulevaisuudessa myös saumaus ja perinteinen nuuttaus on mahdollista tehdä lasersovelluksia käyttäen. Kehittynyt, väyläpohjainen ohjausjärjestelmä on tulevaisuudessa välttämätön joustavassa pakkauslinjassa. Internetin välityksellä toimiva etäohjattu virheenkorjausdiagnostiikka tulee myös olemaan itsestäänselvyys tulevaisuudessa. Kustannussäästöjä voidaan saavuttaa käyttämälläpakkauslinjassa modulaarista rakennetta. Standardiosien ja standardiosajärjestelmien käyttäminen pienentää myös käyttö- ja huoltokustannuksia. Tärkeää on kuitenkin muistaa, ettei joustavuutta voida saavuttaa pelkästään yhtä ominaisuutta tai tekniikkaa hyödyntäen vaan monia menetelmiä yhdistäen. Suunniteltavan pakkauslinjan toiminta on myös hyvä varmistaa käyttäen apuna mallinnusta ja simulointia.

Australiassa muistitietotutkimus on "must" : Old Stories, New Ways

Ajankohtaista

Palveluväylää hyödyntävät järjestelmäintegraatiot

Tässä työssä kuvataan Lahti Fenix Kuntalaistilijärjestelmän ja Tekla Xcity-järjestelmän välille toteutetun järjestelmäintegraation eri vaiheet. Kuntalaistilijärjestelmä on Lahden kaupungin Fenix-hankkeessa kehitteillä oleva sähköinen palvelualusta, jota pitkin kuntalaisille tarjotaan erilaisia kunnallisia palveluja, kuten vastaanottoaikoja hammaslääkärille. Tekla Xcity on kuntien ja kaupunkien käyttöön tarkoitettu järjestelmä, josta on mahdollista hakea esimerkiksi henkilö- ja paikkatietoja. Aluksi työssä esitellään lyhyesti erilaisia tapoja toteuttaa järjestelmäintegraatioita. Seuraavaksi kiinnitetään erityistä huomiota niin sanottuihin web-palveluihin, joiden etuja ja haittoja arvioidaan käytännön esimerkin kautta. Tässä pidetään viitekehyksenä Kuntalaistilijärjestelmää ja siinä käytettyä palvelukeskeistä arkkitehtuuria. Arkkitehtuurin ja viestiliikenneratkaisujen arvioinnin jälkeen siirrytään käytännön osuuteen, jossa itse järjestelmäintegraatio toteutetaan. Järjestelmäintegraatio toteutetaan käyttäen avoimen lähdekoodin palveluväylää ja sille saatavissa olevia viestintäkehyksiä. Integraation eri vaiheissa tutustutaan erilaisiin viestiliikenneprotokolliin ja niiden käyttöön valittujen viestintäkehysten kanssa. Kunkin protokollan toimivuus varmennetaan analysoimalla integraatioon liittyvien komponenttien ja päätepisteiden välistä tietoliikennettä.

Building object-oriented software with the D-Bus messaging system

Object-oriented programming is a widely adopted paradigm for desktop software development. This paradigm partitions software into separate entities, objects, which consist of data and related procedures used to modify and inspect it. The paradigm has evolved during the last few decades to emphasize decoupling between object implementations, via means such as explicit interface inheritance and event-based implicit invocation. Inter-process communication (IPC) technologies allow applications to interact with each other. This enables making software distributed across multiple processes, resulting in a modular architecture with benefits in resource sharing, robustness, code reuse and security. The support for object-oriented programming concepts varies between IPC systems. This thesis is focused on the D-Bus system, which has recently gained a lot of users, but is still scantily researched. D-Bus has support for asynchronous remote procedure calls with return values and a content-based publish/subscribe event delivery mechanism. In this thesis, several patterns for method invocation in D-Bus and similar systems are compared. The patterns that simulate synchronous local calls are shown to be dangerous. Later, we present a state-caching proxy construct, which avoids the complexity of properly asynchronous calls for object inspection. The proxy and certain supplementary constructs are presented conceptually as generic object-oriented design patterns. The e ect of these patterns on non-functional qualities of software, such as complexity, performance and power consumption, is reasoned about based on the properties of the D-Bus system. The use of the patterns reduces complexity, but maintains the other qualities at a good level. Finally, we present currently existing means of specifying D-Bus object interfaces for the purposes of code and documentation generation. The interface description language used by the Telepathy modular IM/VoIP framework is found to be an useful extension of the basic D-Bus introspection format.

Bus bar aeolian vibration field tests

Large amplitude bus bar aeolian vibration may lead to post insulator damage. Different damping applications are used to decrease the risk of large amplitude aeolian vibration. In this paper the post insulator load caused by the bus bar aeolian vibration and the effect of damping methods are evaluated. The effects of three types of bus bar connectors and three types of primary structures are studied. Two actual damping devices, damping cable and their combinations are studied. The post insulator loads are studied with strain gage based custom made force sensors installed on the both ends of the post insulator and with the displacement sensor installed on the midpoint of the bus bar. The post insulator loads are calculated from the strain values and the damping properties are determined from the displacement history. The bus bar is deflected with a hanging weight. The weight is released and the bus bar is left to free damped vibration. Both actual bus bar vibration dampers RIBE and SBI were very effective against the aeolian vibration. Combining vibration damper with damping cable will increase the damping ratio but it may be unnecessary considering the extra effort. Bus bar connector type or primary structure have no effect on the vertical load. The bending moment at the post insulator with double sided bus bar connector is significantly higher than at the post insulator with single sided bus bar connector. No reliable conclusions about bus bar connector type effect can be done, but the roller bearing type or central bearing type connector may reduce the bending moment. The RHS steel frame as primary structure may increase the bending moment peak values since it is the least rigid primary structure type and it may start to vibrate as a response to the awakening force of the vibrating bus bar.

Potential utilization ways of recovered chemical products from digestate

The study evaluates the potential application of chemical substances, obtained from biogas plants` by-products. Through the anaerobic digestion process with biogas the large amount of digestate is produced. This digestate mainly consists on the organic matter with the high concentration of nutrients such as nitrogen and phosphorus. During ammonia stripping and phosphorus precipitation the products- ammonia water, ammonium sulfate, ammonium nitrate, ferrous phosphate, aluminum phosphate, calcium phosphate and struvite can be recovered. These chemicals have potential application in different industrial sectors. According to Finnish market and chemicals properties, the most perspective industrial applications were determined. Based on the data, obtained through the literature review and market study, the ammonia water was recognized as a most perspective recovered substances. According to interview provided among Finnish companies, ammonia water is used for flue gas treatment in SNCR technology. This application has a large scale in the framework of Finnish industrial sectors. As well nitrogen with phosphorous can be used as a source of nutrients in the biological wastewater treatment plants of paper mills.

Mythology as a key to historical ways of thinking

Kirjallisuusarvostelu

20 Ways to Reuse Repository Metadata

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Embedded Service Bus for Internet of Things Interoperability

Internet of Things (IoT) technologies are developing rapidly, and therefore there exist several standards of interconnection protocols and platforms. The existence of heterogeneous protocols and platforms has become a critical challenge for IoT system developers. To mitigate this challenge, few alliances and organizations have taken the initiative to build a framework that helps to integrate application silos. Some of these frameworks focus only on a specific domain like home automation. However, the resource constraints in the large proportion of connected devices make it difficult to build an interoperable system using such frameworks. Therefore, a general purpose, lightweight interoperability framework that can be used for a range of devices is required. To tackle the heterogeneous nature, this work introduces an embedded, distributed and lightweight service bus, Lightweight IoT Service bus Architecture (LISA), which fits inside the network stack of a small real-time operating system for constrained nodes. LISA provides a uniform application programming interface for an IoT system on a range of devices with variable resource constraints. It hides platform and protocol variations underneath it, thus facilitating interoperability in IoT implementations. LISA is inspired by the Network on Terminal Architecture, a service centric open architecture by Nokia Research Center. Unlike many other interoperability frameworks, LISA is designed specifically for resource constrained nodes and it provides essential features of a service bus for easy service oriented architecture implementation. The presented architecture utilizes an intermediate computing layer, a Fog layer, between the small nodes and the cloud, thereby facilitating the federation of constrained nodes into subnetworks. As a result of a modular and distributed design, the part of LISA running in the Fog layer handles the heavy lifting to assist the lightweight portion of LISA inside the resource constrained nodes. Furthermore, LISA introduces a new networking paradigm, Node Centric Networking, to route messages across protocol boundaries to facilitate interoperability. This thesis presents a concept implementation of the architecture and creates a foundation for future extension towards a comprehensive interoperability framework for IoT.

New ways to do business plans in multicultural organizations

Business plans are made when establishing new company or when organizations launch new product or services. In this Master Thesis was examined the elements are included in the business plan and emphasized. Business plan is a wide document and can also contain company specific information, the literature review was restricted into three areas which were investigated from the relating literature and articles. The selected areas were Market Segmentation and Targeting, Competitive Environment, and Market Positioning and Strategy. The different business plan models were investigated by interviewing companies who operates in a different industry sectors from each other’s. The models were compared to each other and to the findings from literature. Based on interview results and literature findings, the business plan for fibre based packaging. The created business plan contains three selected areas. It was found that the selected business plan elements can be found from the interviewed companies’ business plans. The market segmentation was done by comparing the market share to known total market size. When analyzing the competitive environment, there was no one selected model in use. The tools to evaluate competitive environment was selected parts from both SWOT analysis and Porter’s five forces model in applicable part. Based on interview results, it can be state that the company or organization should find and built its own model for business plans. In order to receive the benefits for future planning, the company should use the same model for long time.