Modeling of fractal antennas

In this Master Thesis the characteristics of the chosen fractal microstrip antennas are investigated. For modeling has been used the structure of the square Serpinsky fractal curves. During the elaboration of this Master thesis the following steps were undertaken: 1) calculation and simulation of square microstrip antennа, 2) optimizing for obtaining the required characteristics on the frequency 2.5 GHz, 3) simulation and calculation of the second and third iteration of the Serpinsky fractal curves, 4) radiation patterns and intensity distribution of these antennas. In this Master’s Thesis the search for the optimal position of the port and fractal elements was conducted. These structures can be used in perspective for creation of antennas working at the same time in different frequency range.

Performance Evaluation of Six-Sectored Configuration in Hexagonal WCDMA (UMTS) Cellular Network Layout

The objective of this master's thesis is to evaluate the optimum performance of sixsectored hexagonal layout of WCDMA (UMTS) network and analyze the performance at the optimum point. The maximum coverage and the maximum capacity are the main concern of service providers and it is always a challenging task for them to achieve economically. Because the optimum configuration of a network corresponds to a configuration which minimizes the number of sites required to provide a target service probability in the planning area which in turn reduces the deployment cost. The optimum performance means the maximum cell area and themaximum cell capacity the network can provide at the maximum antenna height satisfying the target service probability. Hexagon layout has been proven as the best layout for the cell deployment. In this thesis work, two different configurations using six-sectored sites have been considered for the performance comparison. In first configuration, each antenna is directed towards each corner of hexagon, whereas in second configurationeach antenna is directed towards each side of hexagon. The net difference in the configurations is the 30 degree rotation of antenna direction. The only indoor users in a flat and smooth semi-urban environment area have been considered for the simulation purpose where the traffic distribution is 100 Erl/km2 with 12.2 kbps speech service having maximum mobile speed of 3 km/hr. The simulation results indicate that a similar performance can be achieved in both the configurations, that is, a maximum of 947 m cellrange at antenna height of 49.5 m can be achieved when the antennas are directed towards the corner of hexagon, whereas 943.3 m cell range atantenna height of 54 m can be achieved when the antennas are directed towards the side of hexagon. However, from the interference point of view the first configuration provides better results. The simulation results also show that the network is coverage limited in both the uplink and downlink direction at the optimum point.

Antennimittausjärjestelmän toteutus ja ominaisuuksien määrittäminen

Diplomityössä tarkasteltiin antennien säteilykuviomittauksiin käytettävien antennimittaratojen ominaisuuksia. Sovelletun elektroniikan laboratorion antennimittaradasta kehitettiin toimiva säteilykuvion mittausjärjestelmä, johon kuuluvat radiokaiuton kammio, suuntauskoneisto ja antennikannakkeet, HP 8720D -piirianalysaattori ja RF-kaapelointi sekä valmistutetut mitta-antennitorvet. Työssä vertailtiin koaksiaalikaapeleita ja valittiin antennimittaukseen soveltuvat. 1,70–2,60 GHz:n taajuusalueen mittastandardiksi suunniteltiin torviantenni, jonka kaksi prototyyppiä valmistutettiin konetekniikan osastolla. Torviantennien ominaisuudet mitattiin. Antennimittaradan ominaisuudet ja soveltuvuus erilaisiin antennimittauksiin selvitettiin sekä teoreettisesti että mittauksin.

DFM(A)- aspects for a horn antenna design

In this paper aspects of design for manufacturability and assembly (DFMA) are applied to the design of coaxially fed standard gain horn antenna for 1.70 - 2.60 GHz. Possibilities to utilize cross-technological approach method is examined. Methods of DFMA for laser processing are covered and practical design guides and methods are developed. Antenna construction for easy manufacturing and specialized performance is shown. Required dimensions and tolerances are discussed and suitable materials for laser processing are selected.

Epäpuhtauksien optinen laskenta sulpusta

Työn tarkoituksena oli hakea mittausjärjestelmän raja-arvoja optiselle kamerapohjaiselle roskalaskentajärjestelmälle sekä testata roskalaskentajärjestelmän toimivuus käytännössä. Tavoitteena oli tuotteistaa kamerapohjainen roskalaskenta-analyysi palvelutuotteeksi, jota voitaisiin hyödyntää sihtien kuntokartoituksessa ja ongelmanratkaisuvälineenä. Teoriaosa koostui kahdesta kokonaisuudesta: sulpun epäpuhtauksista, roskalaskennan teoriasta ja epäpuhtauksien mittausmenetelmistä sekä markkinoinnista, tuotteistamis- ja lanseerausprosessista palvelutuotteen näkökulmasta. Kokeellisessa osassa selvitettiin kamerapohjaiseen roskalaskentaanalyysiin vaikuttavia tekijöitä: kameran tarkennus, kuvan terävyys, analysoitavan arkin väri, neliömassa ja roskapitoisuus, impregnointi, valonlähde, kuvan muokkaus, tiedostomuoto ja pikselimäärä. Kamerapohjaisen roskalaskenta-analyysin soveltuvuus käytäntöön testattiin tehdasesimerkin avulla. Havaittiin, että kamerapohjaista roskalaskenta-analyysiä voitaisiin käyttää lähes kaikille massatyypeille. Työssä määriteltiin kalibrointimenetelmä kameran tarkentamiseksi arkin tasoon sekä suljinnopeusanalyysi massatyypistä riippuvan suljinnopeuden selvitykseen. Kamerapohjaisessa roskalaskenta-analyysissä määritettiin käytettäväksi arkin neliömassana 60 g/m2, suljinaukkoa F5 ja terävyysasetusta 5. Tulokseksi saatiin, että analysoitavia arkkeja ei tarvitse impregnoida tai jälkikäsitellä. Korrelaatiota Somerville-erotustehokkuuteen ei löytynyt. Esimerkkitehtaasta selvitettiin primääriportaan roskapitoisuudet ja erotustehokkuudet. Tehdasesimerkin tulosten perusteella havaittiin happivaiheen ja D0-vaiheen olleen tehokkaimpia epäpuhtauksien poistajia.

ZigBee-verkot ja evaluointilaitteen suunnittelu

In this thesis a closer look at ZigBee wireless network protocol was made and a ZigBee evaluation device was designed and built for testing it. ZigBee is a digital wireless network technology published in 2004, which was developed for wireless control and automation systems. It is based on the IEEE 802.15.4-2003 standard, and its aim was to create a reliable wireless networking protocol with secure data transmissions, low power consumption and low manufacturing costs. The low power consumption requirement has also led to a slow data rate and a short range, but in a ZigBee network individual network devices can route messages to each other, so short range is not a problem. In automation and control systems a fast data rate is not usually an important requirement either. ZigBee network can form automatically and one ZigBee network can theoretically include thousands of devices, all of which can communicate with each other. ZigBee network is also self-healing, so an individual device dropping out of the network, like breaking down, does not affect functionality of the network. Evaluation device was designed and implemented in four different versions, which were tested with six different antenna designs. All antennas were tested at a range of 100 meters in an open terrain using two different frequencies and transmission powers. Also a range test was performed for selected antennas using transmission power of 4,5 dBm, which was maximum power of the ZigBee chip used in the evaluation device. Range test resulted in a measured range of several hundred meters, which can be considered as a good result for a short-range technology.

LTE tulevaisuuden mobiiliverkkoratkaisuna

Tässä kandidaatintyössä käytiin läpi kuinka LTE soveltuu tulevaisuuden mobiiliverkkoratkaisuksi. Ensiksi selvitettiin sen kehityshistoriaa ja vaatimuksia. Seuraavaksi käytiin läpi LTE:n teknistä puolta, kuten radiotekniikkaa, taajuusjakoa ja antenneja. Työssä tehtiin katsaus myös uuteen SAE verkkoarkkitehtuuriin. Teknillisen puolen jälkeen työssä käytiin läpi LTE:n kilpailijoita, sekä tutustuttiin tarkemmin sen pahimpaan haastajaan WiMAX:iin. Näiden kahden tekniikan välillä tehtiin myös vertailu. Lopuksi katsottiin tulevaisuuden trendejä ja mobiilin datasiirron kehittymistä sekä tutustuttiin LTE:n seuraavaan versioon LTE-Advanced:iin.

The Possibilities and Dosimetric Limitations of MLC-Based Intensity-Modulated Radiotherapy Delivery and Optimization Techniques

The use of intensity-modulated radiotherapy (IMRT) has increased extensively in the modern radiotherapy (RT) treatments over the past two decades. Radiation dose distributions can be delivered with higher conformality with IMRT when compared to the conventional 3D-conformal radiotherapy (3D-CRT). Higher conformality and target coverage increases the probability of tumour control and decreases the normal tissue complications. The primary goal of this work is to improve and evaluate the accuracy, efficiency and delivery techniques of RT treatments by using IMRT. This study evaluated the dosimetric limitations and possibilities of IMRT in small (treatments of head-and-neck, prostate and lung cancer) and large volumes (primitive neuroectodermal tumours). The dose coverage of target volumes and the sparing of critical organs were increased with IMRT when compared to 3D-CRT. The developed split field IMRT technique was found to be safe and accurate method in craniospinal irradiations. By using IMRT in simultaneous integrated boosting of biologically defined target volumes of localized prostate cancer high doses were achievable with only small increase in the treatment complexity. Biological plan optimization increased the probability of uncomplicated control on average by 28% when compared to standard IMRT delivery. Unfortunately IMRT carries also some drawbacks. In IMRT the beam modulation is realized by splitting a large radiation field to small apertures. The smaller the beam apertures are the larger the rebuild-up and rebuild-down effects are at the tissue interfaces. The limitations to use IMRT with small apertures in the treatments of small lung tumours were investigated with dosimetric film measurements. The results confirmed that the peripheral doses of the small lung tumours were decreased as the effective field size was decreased. The studied calculation algorithms were not able to model the dose deficiency of the tumours accurately. The use of small sliding window apertures of 2 mm and 4 mm decreased the tumour peripheral dose by 6% when compared to 3D-CRT treatment plan. A direct aperture based optimization (DABO) technique was examined as a solution to decrease the treatment complexity. The DABO IMRT technique was able to achieve treatment plans equivalent with the conventional IMRT fluence based optimization techniques in the concave head-and-neck target volumes. With DABO the effective field sizes were increased and the number of MUs was reduced with a factor of two. The optimality of a treatment plan and the therapeutic ratio can be further enhanced by using dose painting based on regional radiosensitivities imaged with functional imaging methods.

Thermal Stress in a Roll-to-Roll Printed Electronics Substrate

The Roll-to-Roll process makes it possible to print electronic products continuously onto a uniform substrate. Printing components on flexible surfaces can bring down the costs of simple electronic devices such as RFID tags, antennas and transistors. The possibility of quickly printing flexible electronic components opens up a wide array of novel products previously too expensive to produce on a large scale. Several different printing methods can be used in Roll-to-Roll printing, such as gravure, spray, offset, flexographic and others. Most of the methods can also be mixed in one production line. Most of them still require years of research to reach a significant commercial level. The research for this thesis was carried out at the Konkuk University Flexible Display Research Center (KU-FDRC) in Seoul, Korea. A system using Roll-to-Roll printing requires that the motion of the web can be controlled in every direction in order to align different layers of ink properly. Between printers the ink is dried with hot air. The effects of thermal expansion on the tension of the web are studied in this work, and a mathematical model was constructed on Matlab and Simulink. Simulations and experiments lead to the conclusion that the thermal expansion of the web has a great influence on the tension of the web. Also, experimental evidence was gained that the particular printing machine used for these experiments at KU-FDRC may have a problem in controlling the speeds of the cylinders which pull the web.

Länsimaisten SAR/GMTI-tutkien suorituskyky

SAR/GMTI-tutka (Synthetic Aperture Radar/Ground Moving Target Indicator) tuottaa tiedustelutietoa johtamisen, tiedustelun, valvonnan ja maalinosoituksen tueksi. SAR/GMTI -tutka on luotettava tiedusteluväline tutkataajuusalueella tapahtuvan tiedustelutiedon tuottamisen ansiosta, jolloin tutkan käyttö ja tiedustelutiedon tuottaminen onnistuvat huonoissakin sääolosuhteissa. SAR/GMTI-tutkien käyttö on yleistynyt sotilaskäytössä viimeisen kahdenkymmenen vuoden aikana ja niillä on ollut suuri merkitys kaikissa suuremmissa konflikteissa kylmän sodan loppumisen jälkeen. SAR-tutka käyttää lavettina liikkuvaa alustaa, useimmiten lentokonetta, muodostaakseen virtuaalisen antenniryhmän ja signaaliprosessoinnin avulla, jolloin vastaanottimeen palautuvat kaiut sijoitetaan kohdilleen ja muodostetaan SAR-kuvaa. Tarkimmillaan nykyisten SARtutkien resoluutio on muutaman kymmenen senttimetrin luokkaa ja mittausetäisyydet suurimmillaan satoja kilometrejä. GMTI-tutka havaitsee liikkuvat kohteet, kun liikkuvista kohteista palautuvat kaiuilla on eri taajuus kuin ympäröivästä maastosta palautuvilla kaiuilla ja kohteet pystytään erottelemaan välkkeen seasta. GMTI-tutkan toiminta perustuu doppler-ilmiöön. SAR-tutkaa pystytään useimmiten käyttämään GMTI-moodissa. Sotilaskäytössä olevat GMTI-tutkat pystyvät havaitsemaan keskimäärin noin henkilöauton kokoisen maalin, joka liikkuu noin 5 km/h nopeudella. SAR/GMTI-tutkia on käytetty menestyksellisesti molemmissa Irakin sodissa Yhdysvaltojen toimesta, kun tasainen aavikko ei aiheuttanut juurikaan ongelmia alueen valvontaan ilmasta käsin. Sen sijaan haasteita SAR/GMTI-tutkille ovat aiheuttaneet operaatiot Balkanilla ja Afganistanissa korkean vuoriston, peitteisen maaston ja kohteiden hankalan tunnistettavuuden takia. Suoraan taistelun tukemiseen liittyen GMTI-tutkat ovat olleet hyödyllisiä, kun valvontakoneilta saadut tiedot liikkuvista vihollisosastoista on voitu lähettää datalinkkien kautta lähestulkoon reaaliajassa. SAR-tutkat ovat olleet hyödyllisiä ennen taisteluiden alkua tiedustelutiedon keräämisessä ja vaikeakulkuisessa maastossa SAR-tutkia on käytetty esimerkiksi taisteluvaikutuksen jälkiarviointiin. SAR/GMTI-tutkien suorituskyky kehittyy jatkuvasti laitteiden resoluution ja koon pienentyessä. Datalinkeillä voidaan välittää tietoa alajohtoportaille ja SAR/GMTI-tutkia on voitu sijoittaa esimerkiksi UAV-lennokkeihin (Unmanned Aerial Vehicle), joilla on voitu suorittaa tarkempaa aluevalvontaa kuin mitä isomman kokoluokan valvontakoneilla voitaisiin toteuttaa.

Michelson interferometer with porch swing bearing for portable FTIR spectrometer

The interferometer for low resolution portable Fourier Transform middle infrared spectrometer was developed and studied experimentally. The final aim was a concept for a commercial prototype. Because of the portability, the interferometer should be compact sized and insensitive to the external temperature variations and mechanical vibrations. To minimise the size and manufacturing costs, Michelson interferometer based on plane mirrors and porch swing bearing was selected and no dynamic alignment system was applied. The driving motor was a linear voice coil actuator to avoid mechanical contact of the moving parts. The driving capability for low mirror driving velocities required by the photoacoustic detectors was studied. In total, four versions of such an interferometer were built and experimentally studied. The thermal stability during the external temperature variations and the alignment stability over the mirror travel were measured using the modulation depth of the wide diameter laser beam. Method for estimating the mirror tilt angle from the modulation depth was developed to take account the effect from the non-uniform intensity distribution of the laser beam. The spectrometer stability was finally studied also using the infrared radiation. The latest interferometer was assembled for the middle infrared spectrometer with spectral range from 750 cm−1 to 4500 cm−1. The interferometer size was (197 × 95 × 79) mm3 with the beam diameter of 25 mm. The alignment stability as the change of the tilt angle over the mirror travel of 3 mm was 5 μrad, which decreases the modulation depth only about 0.7 percent in infrared at 3000 cm−1. During the temperature raise, the modulation depth at 3000 cm−1 changed about 1 . . . 2 percentage units per Celsius over short term and even less than 0.2 percentage units per Celsius over the total temperature raise of 30 °C. The unapodised spectral resolution was 4 cm−1 limited by the aperture size. The best achieved signal to noise ratio was about 38 000:1 with commercially available DLaTGS detector. Although the vibration sensitivity requires still improving, the interferometer performed, as a whole, very well and could be further developed to conform all the requirements of the portable and stable spectrometer.

Radar cross-section measurement using the Doppler effect

In this Master Thesis we discuss issues related to the measurement of the effective scattering surface, based on the Doppler Effect. Modeling of the detected signal was made. Narrowband signal filtering using low-frequency amplifier was observed. Parameters of the proposed horn antennas were studied; radar cross section charts for three different objects were received.

Antenna feed design for omnidirectional broadband antenna

This thesis is about development broadband feed for two-mirror antenna system that match following requirements: beamwidth from 45 to 90 degrees at -3 dB level, circular polarization, absence of radiation to the lower hemisphere area. Literature review was done in the areas of the UWB antennas creation. During the work attempts were made to create a feed in a form of the quad ridged horn and "eleven" antennas. The latter is introduced as the most effective feed among all antennas discussed in thesis. Radiation patterns and other results for "eleven" antenna were obtained. Results were saved as far field sources and placed slightly below focal point into the two-mirror antenna system, because phase center of the “eleven” antenna is predominantly shifted upwards. Directivity patterns for the two-mirror system were obtained and the conclusions about the work results have been made

Control of a line robot system with Embedded Linux

Many, if not all, aspects of our everyday lives are related to computers and control. Microprocessors and wireless communications are involved in our lives. Embedded systems are an attracting field because they combine three key factors, small size, low power consumption and high computing capabilities. The aim of this thesis is to study how Linux communicates with the hardware, to answer the question if it is possible to use an operating system like Debian for embedded systems and finally, to build a Mechatronic real time application. In the thesis a presentation of Linux and the Xenomai real time patch is given, the bootloader and communication with the hardware is analyzed. BeagleBone the evaluation board is presented along with the application project consisted of a robot cart with a driver circuit, a line sensor reading a black line and two Xbee antennas. It makes use of Xenomai threads, the real time kernel. According to the obtained results, Linux is able to operate as a real time operating system. The issue of future research is the area of embedded Linux is also discussed.