Antenna feed design for omnidirectional broadband antenna

This thesis is about development broadband feed for two-mirror antenna system that match following requirements: beamwidth from 45 to 90 degrees at -3 dB level, circular polarization, absence of radiation to the lower hemisphere area. Literature review was done in the areas of the UWB antennas creation. During the work attempts were made to create a feed in a form of the quad ridged horn and "eleven" antennas. The latter is introduced as the most effective feed among all antennas discussed in thesis. Radiation patterns and other results for "eleven" antenna were obtained. Results were saved as far field sources and placed slightly below focal point into the two-mirror antenna system, because phase center of the “eleven” antenna is predominantly shifted upwards. Directivity patterns for the two-mirror system were obtained and the conclusions about the work results have been made

DFM(A)- aspects for a horn antenna design

In this paper aspects of design for manufacturability and assembly (DFMA) are applied to the design of coaxially fed standard gain horn antenna for 1.70 - 2.60 GHz. Possibilities to utilize cross-technological approach method is examined. Methods of DFMA for laser processing are covered and practical design guides and methods are developed. Antenna construction for easy manufacturing and specialized performance is shown. Required dimensions and tolerances are discussed and suitable materials for laser processing are selected.

Antennimittausjärjestelmän toteutus ja ominaisuuksien määrittäminen

Diplomityössä tarkasteltiin antennien säteilykuviomittauksiin käytettävien antennimittaratojen ominaisuuksia. Sovelletun elektroniikan laboratorion antennimittaradasta kehitettiin toimiva säteilykuvion mittausjärjestelmä, johon kuuluvat radiokaiuton kammio, suuntauskoneisto ja antennikannakkeet, HP 8720D -piirianalysaattori ja RF-kaapelointi sekä valmistutetut mitta-antennitorvet. Työssä vertailtiin koaksiaalikaapeleita ja valittiin antennimittaukseen soveltuvat. 1,70–2,60 GHz:n taajuusalueen mittastandardiksi suunniteltiin torviantenni, jonka kaksi prototyyppiä valmistutettiin konetekniikan osastolla. Torviantennien ominaisuudet mitattiin. Antennimittaradan ominaisuudet ja soveltuvuus erilaisiin antennimittauksiin selvitettiin sekä teoreettisesti että mittauksin.

Tuning the design procedures for laser processed microwave mechanics

This research has been focused at the development of a tuned systematic design methodology, which gives the best performance in a computer aided environment and utilises a cross-technological approach, specially tested with and for laser processed microwave mechanics. A tuned design process scheme is also presented. Because of the currently large production volumes of microwave and radio frequency mechanics even slight improvements of design methodologies or manufacturing technologies would give reasonable possibilities for cost reduction. The typical number of required iteration cycles could be reduced to one fifth of normal. The research area dealing with the methodologies is divided firstly into a function-oriented, a performance-oriented or a manufacturability-oriented product design. Alternatively various approaches can be developed for a customer-oriented, a quality-oriented, a cost-oriented or an organisation-oriented design. However, the real need for improvements is between these two extremes. This means that the effective methodology for the designers should not be too limited (like in the performance-oriented design) or too general (like in the organisation-oriented design), but it should, include the context of the design environment. This is the area where the current research is focused. To test the developed tuned design methodology for laser processing (TDMLP) and the tuned optimising algorithm for laser processing (TOLP), seven different industrial product applications for microwave mechanics have been designed, CAD-modelled and manufactured by using laser in small production series. To verify that the performance of these products meets the required level and to ensure the objectiveness ofthe results extensive laboratory tests were used for all designed prototypes. As an example a Ku-band horn antenna can be laser processed from steel in 2 minutes at the same time obtaining a comparable electrical performance of classical aluminium units or the residual resistance of a laser joint in steel could be limited to 72 milliohmia.

Development of advanced silicon radiation detectors for harsh radiation environment

This thesis describes the development of advanced silicon radiation detectors and their characterization by simulations, used in the work for searching elementary particles in the European Organization for Nuclear Research, CERN. Silicon particle detectors will face extremely harsh radiation in the proposed upgrade of the Large Hadron Collider, the future high-energy physics experiment Super-LHC. The increase in the maximal fluence and the beam luminosity up to 1016 neq / cm2 and 1035 cm-2s-1 will require detectors with a dramatic improvement in radiation hardness, when such a fluence will be far beyond the operational limits of the present silicon detectors. The main goals of detector development concentrate on minimizing the radiation degradation. This study contributes mainly to the device engineering technology for developing more radiation hard particle detectors with better characteristics. Also the defect engineering technology is discussed. In the nearest region of the beam in Super-LHC, the only detector choice is 3D detectors, or alternatively replacing other types of detectors every two years. The interest in the 3D silicon detectors is continuously growing because of their many advantages as compared to conventional planar detectors: the devices can be fully depleted at low bias voltages, the speed of the charge collection is high, and the collection distances are about one order of magnitude less than those of planar technology strip and pixel detectors with electrodes limited to the detector surface. Also the 3D detectors exhibit high radiation tolerance, and thus the ability of the silicon detectors to operate after irradiation is increased. Two parameters, full depletion voltage and electric field distribution, is discussed in more detail in this study. The full depletion of the detector is important because the only depleted area in the detector is active for the particle tracking. Similarly, the high electric field in the detector makes the detector volume sensitive, while low-field areas are non-sensitive to particles. This study shows the simulation results of full depletion voltage and the electric field distribution for the various types of 3D detectors. First, the 3D detector with the n-type substrate and partial-penetrating p-type electrodes are researched. A detector of this type has a low electric field on the pixel side and it suffers from type inversion. Next, the substrate is changed to p-type and the detectors having electrodes with one doping type and the dual doping type are examined. The electric field profile in a dual-column 3D Si detector is more uniform than that in the single-type column 3D detector. The dual-column detectors are the best in radiation hardness because of their low depletion voltages and short drift distances.

Laajakaistainen Vivaldi-antennielementti

Diplomityössä suunniteltiin, rakennettiin ja mitattiin laajakaistainen antennielementti lineaariseen antenniryhmään. Elementti toimii mikroaaltoalueella, ja sen kaistanleveys on noin 4,8:1. Elementti koostuu kaksipuolisesta eksponentiaalisesti taperoidusta rakoantennista eli Vivaldi-antennista ja laajakaistaisesta siirtymästä liuskajohdosta kaksipuoliseen rakojohtoon. Elementin koko pienimmällä käyttötaajuudella on noin 0,31 lambda kertaa 0,34 lambda, josta antennitorven koko on vain noin 0,21 lambda kertaa 0,21 lambda. Elementti suunniteltiin HFSS-simulointiohjelman avulla ja rakennettiin kahdesta erillisestä piirilevystä puristamalla nämä yhteen alumiinisella kehyksellä. Mittauksilla varmistettiin elementin toiminta ja simulointien luotettavuus. Osoitettiin, että elementti voidaan suunnitella simulointiohjelman avulla ja rakentaa työssä käytetyllä tavalla. Osoitettiin myös, että tarvittavaa mitoitussimulointien määrää voidaan vähentää yhdistämällä erikseen mitoitetut rakoantenni ja siirtymä. Lisäksi simuloinnein osoitettiin, että elementti toimii myös ryhmässä ja että sen toimintaa voidaan parantaa kehyksen avulla.

Larghetto for Horn and Orchestra

Soitinnus: Käyrätorvi, ork.

Antenna Design for Contactless IC Card Applications

Contactless integrated circuit cards are one form of application of radio frequency identification. They are used in applications such as access control, identification, and payment in public transport. The contactless IC cards are passive which means that both the data and the energy are transferred to the card without contact using inductive coupling. Antenna design and optimization of the design for contactless IC cards defined by ISO/IEC14443 is studied. The basic operation principles of contactless system are presented and the structure of contactless IC card is illustrated. The structure was divided between the contactless chip and the antenna. The operation of the antenna was covered in depth and the parameters affecting to the performance of the antenna were presented. Also the different antenna technologies and connection technologies were provided. The antenna design process with the parameters and the design tools isillustrated and optimization of the design is studied. To make the design process more ideal a target of development was discovered, which was the implementation of test application. The optimization of the antenna design was presented based on the optimization criteria defined in this study. The solution for the implementation of these criteria and the effect of each criterion was found. For enhancing the performance of the antenna a focus for future study was proposed.

Design and characterization of large area position sensitive radiation detectors

Planar, large area, position sensitive silicon detectors are widely utilized in high energy physics research and in medical, computed tomography (CT). This thesis describes author's research work relating to development of such detector components. The key motivation and objective for the research work has been the development of novel, position sensitive detectors improving the performance of the instruments they are intended for. Silicon strip detectors are the key components of barrel-shaped tracking instruments which are typically the innermost structures of high energy physics experimental stations. Particle colliders such as the former LEP collider or present LHC produce particle collisions and the silicon strip detector based trackers locate the trajectories of particles emanating from such collisions. Medical CT has become a regular part of everyday medical care in all developed countries. CT scanning enables x-ray imaging of all parts of the human body with an outstanding structural resolution and contrast. Brain, chest and abdomen slice images with a resolution of 0.5 mm are possible and latest CT machines are able to image whole human heart between heart beats. The two application areas are presented shortly and the radiation detection properties of planar silicon detectors are discussed. Fabrication methods and preamplifier electronics of the planar detectors are presented. Designs of the developed, large area silicon detectors are presented and measurement results of the key operating parameters are discussed. Static and dynamic performance of the developed silicon strip detectors are shown to be very satisfactory for experimental physics applications. Results relating to the developed, novel CT detector chips are found to be very promising for further development and all key performance goals are met.

The Global War on Terrorism in the Horn of Africa

Ever since Siad Barre’s regime was toppled in the beginning of the 1990’s Somalia has been without an effective central government. As a result Somalia has remained in an anarchic condition of state collapse for nearly two decades. This anarchy has often been put forward as a potential breeding ground for terrorism. As a response to this threat the United States has undertaken several policies, initiatives, and operations in the Horn of Africa generally and in Somalia specifically. In this descriptive study a twofold analysis has been undertaken. First, conditions in present day Somalia as well as Somali history have been analyzed to evaluate the potential Somalia holds as a terrorist base of operations or a recruiting- or staging area. Second, US strategies and actions have been analyzed to evaluate the adequacy of the US response to the threat Somalia poses in terms of terrorism. Material for the analyses have been derived from anthropological, political, and security studies dealing with Somalia. This material has been augmented by a wide range of news coverage, western and non-western. Certain different US policy documents from different levels have been chosen to represent US strategies for the Global War on Terrorism. Because Somali social institutions, such as the clan system, hold great weight in Somali society, Somalia is a difficult area of operations for terrorist networks. In addition the changing nature of Somali alliances and the tangled webs of conflict that characterize present day Somalia aggravate the difficulties that foreign terrorist networks would encounter in Somalia, would they choose to try to utilize it in any great extent. The US has taken potential terrorism threats in Africa and specifically Somalia very seriously. US actions in Somalia have mainly focused on apprehending or neutralizing terror suspects. Such policies, coupled with backing the Ethiopian invasion of Somalia may have actually turned out increasing Somalia’s terror potential.