Kulutus- korroosionkestävien materiaalien laserpinnoitus

Diplomityössä tutkitaan kulutus- ja korrosionkestävien materiaalien laserpinnoitusta. Laserpinnoituksessa sulatetaan uutta materiaalia työkappaleen pintaan lasersäteen avulla. Tarkoituksena on yleensä parantaa pinnan korroosion, kulumisen tai pintapaineen kestävyyttä. Laserpinnoitukseen liittyy useita etuja verrattuna konventionaalisiin päällehitsausprosesseihin. Työssä tutkittavat pinnoitemateriaalit ovat kobolttipohjaiset Stellite 1 ja Stellite 6, työkaluteräkset WR 4 ja WR 6 sekä metallimatriisikomposiitti Anval50/50+30 % Cr3C2. Pinnoitettavat perusaineet ovat hiiliteräs Fe 52, ruostumaton teräs AISI 316 ja valurauta GRP 500. Työn tavoitteena on löytää kunkin pinnoite/perusaine-yhdistelmän pinnoitusparametrit. Pinnoituskokeissa käytettiin LTKK:n 6 kW:n CO2-laseria. Pinnoitetuille koekappeleille tehtiin kovuusmittaukset ja kulutuskokeet. Pinnoitteiden mikrorakenteet analysoitiin ja sekoittumisasteet laskettiin. Virheitä tutkittiin silmämääräisesti sekä radiografisella kuvauksella. Optimiparametreja pinnoitemateriaaleille ei löydetty. Pinnoitteiden sekoittumisasteet muodostuivat suuriksi liiallisen lasertehon ja/tai huonon lisäaineen kohdistuksen vuoksi. Suuri sekoittuminen alensi pinnoitteiden kovuutta ja kulumiskestävyyttä. Pinnoitusparametreja arvioidaan koetulosten perusteella ja niille annetaan korjausehdotuksia. Lopuksi esitetään suosituksia tutkimusprojektin jatkotoimille.

Utilization of non ferrous metals in boiler combustion environment

The made research is focused on possibility of application of non ferrous metals in boiler pressure parts as a substitute of currently used ferrous-base alloys. The main issue was to define resistive ability of some perspective non ferrous metals to chlorine induced corrosion. Experimental study was performed using simultaneous thermal analysis (STA) in the temperature range of 400-700 °C. The chloride induced corrosion was simulated by mixtures of metal samples with potassium chloride treated by synthetic air. The advantage of synergetic effect of non ferrous alloys compare to single metals is shown due to the obtained data from conducted thermal balance tests.

Weldability of high strength aluminium alloys

The need for reduced intrinsic weight of structures and vehicles in the transportation industry has made aluminium research of interest. Aluminium has properties that are favourable for structural engineering, including good strength-to-weight ratio, corrosion resistance and machinability. It can be easily recycled saving energy used in smelting as compared to steel. Its alloys can have ultimate tensile strength of up to 750 MPa, which is comparable to steel. Aluminium alloys are generally weldable, however welding of high strength alloys like the 7xxx series pose considerable challenges. This paper presents research on the weldability of high strength aluminium alloys, principally the 7xxx series. The weldability with various weld processes including MIG, TIG, and FSW, is discussed in addition to consideration of joint types, weld defects and recommendations for minimizing or preventing weld defects. Experimental research was carried out on 7025-T6 and AW-7020 alloys. Samples were welded, and weld cross sections utilized in weld metallurgy studies. Mechanical tests were carried out including hardness tests and tensile tests. In addition, testing was done for the presence of Al2O3 on exposed aluminium alloy. It was observed that at constant weld heat input using a pulsed MIG system, the welding speed had little or no effect on the weld hardness. However, the grain size increased as the filler wire feed rate, welding current and welding speed increased. High heat input resulted in lower hardness of the weld profile. Weld preheating was detrimental to AW- 7020 welds; however, artificial aging was beneficial. Acceptable welds were attained with pulsed MIG without the removal of the Al2O3 layer prior to welding. The Al2O3 oxide layer was found to have different compositions in different aluminium alloys. These findings contribute useful additional information to the knowledge base of aluminium welding. The application of the findings of this study in welding will help reduce weld cost and improve high strength aluminium structure productivity by removing the need for pre-weld cleaning. Better understanding of aluminium weld metallurgy equips weld engineers with information for better aluminium weld design.

Effect of Shielding Gases in Laser Welding of Aluminium Alloys

High reflectivity to laser light, alloying element evaporation during high power laser welding makes aluminium alloys highly susceptibility to weld defects such as porosity, cracking and undercutting. The dynamic behaviour of the keyhole, due to fluctuating plasma above the keyhole and the vaporization ofthe alloying elements with in the keyhole, is the key problem to be solved for the improvement of the weld quality and stabilization of the keyhole dynamics isperhaps the single most important development that can broaden the application of laser welding of aluminium alloys. In laser welding, the shielding gas is commonly used to stabilize the welding process, to improve the welded joint features and to protect the welded seam from oxidation. The chemicalcomposition of the shielding gas is a key factor in achieving the final qualityof the welded joints. Wide range of shielding gases varying from the pure gasesto complex mixtures based on helium, argon, nitrogen and carbon dioxide are commercially available. These gas mixtures should be considered in terms of their suitability during laser welding of aluminium alloys to produce quality welds. The main objective of the present work is to study the effect of the shielding gascomposition during laser welding of aluminium alloys. Aluminium alloy A15754 was welded using 3kW Nd-YAG laser (continuous wave mode). The alloy samples were butt welded with different shielding gases (pure and mixture of gases) so that high quality welds with high joint efficiencies could be produced. It was observed that the chemical composition of the gases influenced the final weld quality and properties. In general, the mixture gases, in correct proportions, enabled better utilisation of the properties of the mixing gases, stabilized the welding process and produced better weld quality compared to the pure shielding gases.

Nd:YAG Laser Welding of 5083 Aluminium Alloy using Filler Wire

High reflectivity and high thermal conductivity, high vapour pressure of alloyingelements as well as low liquid surface tension and low ionisation potential, make laser welding of aluminium and its alloys a demanding task.Problems that occur during welding are mainly process instabilities of the keyhole and the melt pool, increased plasma formation above the melt pool and loss of alloying elements. These problems lead to unwanted metallurgical defects like hot cracks and porosity in the weld bead andother problems concerning the shape and appearance of the weld bead. In order to minimise the defects and improve the weld quality, the process and beam parameters need to be carefully adjusted along with a consideration concerning the use of filler wire for the welding process. In this work the welding of 3,0 mm thick grade 5083 aluminium alloy plates using a 3,0 kW Nd:YAG laser with grade 5183 filler wire addition is investigated. The plates were welded as butt joints with air gap sizes 0,5 mm, 0,7mm and 1,0 mm. The analysis of the weld beads obtained from the weldedsamples showed that the least imperfections were produced with 0,7 mm air gaps at moderate welding speeds. The analysis also covered the calculation of the melting efficiency and the study of the shape of the weld bead. The melting efficiency was on average around 20 % for the melting process of the welded plates. The weld beads showed the characteristic V-shape of a laser weld and retained this shape during the whole series of experiments.

Spectroscopic monitoring during laser welding of aluminium alloy

The mechanical properties of aluminium alloys are strongly influenced by the alloying elements and their concentration. In the case of aluminium alloy EN AW-6060 the main alloying elements are magnesium and silicon. The first goal of this thesis was to determine stability, repeatability and sensitivity as figures of merit of the in-situ melt identification technique. In this study the emissions from the laser welding process were monitored with a spectrometer. With the information produced by the spectrometer, quantitative analysis was conducted to determine the figures of merit. The quantitative analysis concentrated on magnesium and aluminium emissions and their relation. The results showed that the stability of absolute intensities was low, but the normalized magnesium emissions were quite stable. The repeatability of monitoring magnesium emissions was high (about 90 %). Sensitivity of the in-situ melt identification technique was also high. As small as 0.5 % change in magnesium content was detected by the spectrometer. The second goal of this study was to determine the loss of mass during deep penetration laser welding. The amount of magnesium in the material was measured before and after laser welding to determine the loss of magnesium. This study was conducted for aluminium alloy with nominal magnesium content of 0-10 % and for standard material EN AW-6060 that was welded with filler wire AlMg5. It was found that while the magnesium concentration in the material changed, the loss of magnesium remained fairly even. Also by feeding filler wire, the behaviour was similar. Thirdly, the reason why silicon had not been detected in the emission spectrum needed to be explained. Literature research showed that the amount of energy required for silicon to excite is considerably higher compared to magnesium. The energy input in the used welding process is insufficient to excite the silicon atoms.

Hitsatun alumiinirakenteen suunnittelu

Alumiiniseosten käyttö konstruktiomateriaalina lisääntyy johtuen sen lukuisista variaatioista lujuuden ja muovattavuuden suhteen. Alumiinin keveys on merkittävä kilpailuetu teräkseen nähden. Alumiiniseosten hitsattavuus on parantunut hitsausmenetelmien kehittyessä. Uusilla menetelmillä lämmöntuontia hallitaan paremmin, kuten myös alumiinin huokoisuutta sekä lujuuden laskua hitsauksen yhteydessä. Tässä diplomityössä tutkitaan alumiinin metallurgiaa, hitsausmenetelmiä, sekä alumiinin ja teräksen sekaliitoksen toteutusta. Tutkimuksella pyritään tekemään hitsatun alumiinirakenteen suunnittelua ymmärrettävämmäksi. SFS-EN standardit antavat perustuksen alumiinirakenteen suunnittelulle. Tässä diplomityössä tehdään suunnitteluesimerkki hitsatun alumiinirakenteen hitsien suunnittelusta. Suunnitteluesimerkissä tutkitaan alumiiniseoksen lujuuden laskua hitsattaessa, ja etsitään standardien antamia ratkaisuja toimivan hitsatun rakenteen toteuttamiseksi.

Backhoe loaders as base machines in logging operations

Summary

Effect of anionic salts in concentrate mixture on some blood and urine minerals, acid-base balance and feed intake of dry pregnant cows on grass silage based feeding with high calcium intake

Selostus: Kationi-anionitasapaino ummessaolevien lypsylehmien säilörehuruokinnassa kalsiumin saannin ollessa runsas

Effect of anionic salts in concentrate mixture and calcium intake on some blood and urine minerals, acid-base balance and feed intake of dry pregnant cows on grass silage based feeding

Selostus: Kationi-anionitasapaino ja kalsiumin saanti ummessaolevien lypsylehmien säilörehuruokinnassa

Effect of anionic salts in concentrate mixture and magnesium intake on some blood and urine minerals and acid-base balance of dry pregnant cows on grass silage based feeding

Selostus: Kationi-anionitasapaino ja magnesiumin saanti ummessaolevien lypsylehmien säilörehuruokinnassa