Cost Models for Routing and Wavelength Assignment in Wavelength-Division Multiplexing Optical Net

WDM (Wavelength-Division Multiplexing) optiset verkot on tällä hetkellä suosituin tapa isojen määrän tietojen siirtämiseen. Jokaiselle liittymälle määrätään reitin ja aallonpituus joka linkin varten. Tarvittavan reitin ja aallon pituuden löytäminen kutsutaan RWA-ongelmaksi. Tämän työn kuvaa mahdollisia kustannuksen mallein ratkaisuja RWA-ongelmaan. Olemassa on paljon erilaisia optimoinnin tavoitteita. Edellä mainittuja kustannuksen malleja perustuu näillä tavoitteilla. Kustannuksen malleja antavat tehokkaita ratkaisuja ja algoritmeja. The multicommodity malli on käsitelty tässä työssä perusteena RV/A-kustannuksen mallille. Myöskin OB käsitelty heuristisia menetelmiä RWA-ongelman ratkaisuun. Työn loppuosassa käsitellään toteutuksia muutamalle mallille ja erilaisia mahdollisuuksia kustannuksen mallein parantamiseen.

Impact of unsymmetrical loads in distribution networks

Since it is virtually impossible to balance loads in three-phase system, unbalance in a varying degree exists almost in all distribution networks. The aim of the thesis is to analyze the impact of this unbalance subject to different configurations of distribution system and winding connection of the supplying transformer. Also impact of the voltage unbalance on the equipment is investigated. In order to make the investigation more visual, the following calculations have been conducted: - Unsymmetrical load in four-wire star connected network - Unsymmetrical load in four-wire star connected network with broken zero conductor (or three-wire network). - Unsymmetrical load when the supplying transformer is so-called zigzag transformer. PDF created

Local Services in a Fourth Generation Mobile Network

Neljännen sukupolven mobiiliverkot kokoaa kaikki tietoliikenneverkot ja palvelut Internetin ympärille. Tämä mullistus muuttaa vanhat vertikaaliset tietoliikenneverkot joissa yhden tietoliikenneverkon palvelut ovat saatavissa vain kyseisen verkon päätelaitteille horisontaaliseksi malliksi jossa päätelaitteet käyttävät omaa verkkoansa pääsynä Internetin palveluihin. Tämä diplomityö esittelee idean paikallisista palveluista neljännen sukupolven mobiiliverkossa. Neljännen sukupolven mobiiliverkko yhdistää perinteiset televerkkojen palvelut ja Internet palvelut sekä mahdollistaa uuden tyyppisten palveluiden luonnin. TCP/IP protokollien ja Internetin evoluutio on esitelty. Laajakaistaiset, lyhyen kantaman radiotekniikat joita käytetään langattomana yhteytenä Internetiin on käsitelty. Evoluutio kohti neljännen sukupolven mobiiliverkkoja on kuvattu esittelemällä vanhat, nykyiset ja tulevat mobiiliverkot sekä niiden palvelut. Ennustukset palveluiden ja markkinoiden tulevaisuuden kehityksestä on käsitelty. Neljännen sukupolven mobiiliverkon arkkitehtuuri mahdollistaa paikalliset palvelut jotka ovat saatavilla vain yhdessä paikallisessa 4G verkossa. Paikalliset palvelut voidaan muunnella jokaiselle käyttäjälle erikseen käyttäen profiili-informaatiota ja paikkatietoa. Työssä on pohdittu paikallisten palveluiden käyttökelpoisuutta ja mahdollisuuksia käyttäen Lappeenrannan teknillisen korkeakoulun 4G projektin palvelupilotin tuloksia.

Investigation of the two-photon induced fluorescence in Rb vapour excited by Ti:Sapphire femtosecond laser pulses

In this work we report the observation of the blue visible fluorescence at 420 nm in rubidium vapour as a result of two-photon absorption excited by femtosecond laser pulses 790 nm. After experimental investigation of the spa-tial and spectral characteristics of the obtained emission we can claim that mechanism of this coherent fluorescence at 420 nm was not caused by ampli-fied spontaneous emission, but represents the nondegenerate four-wave mixing. As a probable outcome of this investigation an opportunity of creation an ultrafast all-optical switcher might appear.

Memory Effects in the Dynamics of Open Quantum Systems

In this Thesis various aspects of memory effects in the dynamics of open quantum systems are studied. We develop a general theoretical framework for open quantum systems beyond the Markov approximation which allows us to investigate different sources of memory effects and to develop methods for harnessing them in order to realise controllable open quantum systems. In the first part of the Thesis a characterisation of non-Markovian dynamics in terms of information flow is developed and applied to study different sources of memory effects. Namely, we study nonlocal memory effects which arise due to initial correlations between two local environments and further the memory effects induced by initial correlations between the open system and the environment. The last part focuses on describing two all-optical experiment in which through selective preparation of the initial environment states the information flow between the system and the environment can be controlled. In the first experiment the system is driven from the Markovian to the non- Markovian regime and the degree of non-Markovianity is determined. In the second experiment we observe the nonlocal nature of the memory effects and provide a novel method to experimentally quantify frequency correlations in photonic environments via polarisation measurements.

Two-dimensional atom localization and Raman cooling of tripod-type atoms

Both atom localization and Raman cooling, considered in the thesis, reflect recent progress in the area of all-optical methods. We focus on twodimensional (2D) case, using a four-level tripod-type atomic scheme for atom localization within the optical half-wavelength as well as for efficient subrecoil Raman cooling. In the first part, we discuss the principles of 1D atom localization, accompanying by an example of the measurement of a spontaneously-emitted photon. Modifying this example, one archives sub-wavelength localization of a three-level -type atom, measuring the population in its upper state. We go further and obtain 2D sub-wavelength localization for a four-level tripod-type atom. The upper-state population is classified according to the spatial distribution, which in turn forms such structures as spikes, craters and waves. The second part of the thesis is devoted to Raman cooling. The cooling process is controlled by a sequence of velocity-selective transfers from one to another ground state. So far, 1D deep subrecoil cooling has been carried out with the sequence of square or Blackman pulses, applied to -type atoms. In turn, we discuss the transfer of atoms by stimulated Raman adiabatic passage (STIRAP), which provides robustness against the pulse duration if the cooling time is not in any critical role. A tripod-type atomic scheme is used for the purpose of 2D Raman cooling, allowing one to increase the efficiency and simplify the realization of the cooling.

On the differential evolution algorithm and its appliation to training radial basis function networks

The parameter setting of a differential evolution algorithm must meet several requirements: efficiency, effectiveness, and reliability. Problems vary. The solution of a particular problem can be represented in different ways. An algorithm most efficient in dealing with a particular representation may be less efficient in dealing with other representations. The development of differential evolution-based methods contributes substantially to research on evolutionary computing and global optimization in general. The objective of this study is to investigatethe differential evolution algorithm, the intelligent adjustment of its controlparameters, and its application. In the thesis, the differential evolution algorithm is first examined using different parameter settings and test functions. Fuzzy control is then employed to make control parameters adaptive based on an optimization process and expert knowledge. The developed algorithms are applied to training radial basis function networks for function approximation with possible variables including centers, widths, and weights of basis functions and both having control parameters kept fixed and adjusted by fuzzy controller. After the influence of control variables on the performance of the differential evolution algorithm was explored, an adaptive version of the differential evolution algorithm was developed and the differential evolution-based radial basis function network training approaches were proposed. Experimental results showed that the performance of the differential evolution algorithm is sensitive to parameter setting, and the best setting was found to be problem dependent. The fuzzy adaptive differential evolution algorithm releases the user load of parameter setting and performs better than those using all fixedparameters. Differential evolution-based approaches are effective for training Gaussian radial basis function networks.

Object-Oriented Modelling of Multilayer Networks

Tämä diplomityökuuluu tietoliikenneverkkojen suunnittelun tutkimukseen ja pohjimmiltaan kohdistuu verkon mallintamiseen. Tietoliikenneverkkojen suunnittelu on monimutkainen ja vaativa ongelma, joka sisältää mutkikkaita ja aikaa vieviä tehtäviä. Tämä diplomityö esittelee ”monikerroksisen verkkomallin”, jonka tarkoitus on auttaa verkon suunnittelijoita selviytymään ongelmien monimutkaisuudesta ja vähentää verkkojen suunnitteluun kuluvaa aikaa. Monikerroksinen verkkomalli perustuu yleisille objekteille, jotka ovat yhteisiä kaikille tietoliikenneverkoille. Tämä tekee mallista soveltuvan mielivaltaisille verkoille, välittämättä verkkokohtaisista ominaisuuksista tai verkon toteutuksessa käytetyistä teknologioista. Malli määrittelee tarkan terminologian ja käyttää kolmea käsitettä: verkon jakaminen tasoihin (plane separation), kerrosten muodostaminen (layering) ja osittaminen (partitioning). Nämä käsitteet kuvataan yksityiskohtaisesti tässä työssä. Monikerroksisen verkkomallin sisäinen rakenne ja toiminnallisuus ovat määritelty käyttäen Unified Modelling Language (UML) -notaatiota. Tämä työ esittelee mallin use case- , paketti- ja luokkakaaviot. Diplomityö esittelee myös tulokset, jotka on saatu vertailemalla monikerroksista verkkomallia muihin verkkomalleihin. Tulokset osoittavat, että monikerroksisella verkkomallilla on etuja muihin malleihin verrattuna.

Building an Access Network for Triple-Play Services

This final project was made for the Broadband department of TeliaSonera. This project gives an overview on how internet service provider might build an access network so that they can offer triple-play services. It also gives information on what equipment is needed and what is required from the access, aggregation and edge networks. The project starts by describing the triple-play service. Then it moves on to optical fiber cables, the network technology and network architecture. At the end of the project there is an example of the process and construction of the access network. It will give an overview of the total process and problems that a network planner might face during the planning phase of the project. It will give some indication on how one area is built from the start to finish. The conclusion of the project presents some points that must be taken into consideration when building an access network. The building of an access network has to be divided to a time span of eight to ten years, where one year is one phase in the project. One phase is divided into three parts; Selecting the areas and targets, Planning the areas and targets, and Documentation. The example area gives indication on the planning of an area. It is almost impossible to connect all targets at the same time. This means that the service provider has to complete the construction in two or three parts. The area is considered to be complete when more than 80% of the real estates have fiber.

Use of the Optical Cantilever Microphone in Photoacoustic Spectroscopy

A novel cantilever pressure sensor was developed in the Department of Physics at the University of Turku in order to solve the sensitivity problems which are encountered when condenser microphones are used in photoacoustic spectroscopy. The cantilever pressure sensor, combined with a laser interferometer for the measurement of the cantilever movements, proved to be highly sensitive. The original aim of this work was to integrate the sensor in a photoacoustic gas detector working in a differential measurement scheme. The integration was made successfully into three prototypes. In addition, the cantilever was also integrated in the photoacoustic FTIR measurement schemes of gas-, liquid-, and solid-phase samples. A theoretical model for the signal generation in each measurement scheme was created and the optimal celldesign discussed. The sensitivity and selectivity of the differential method were evaluated when a blackbody radiator and a mechanical chopper were used with CO₂, CH4, CO, and C2H4 gases. The detection limits were in the sub-ppm level for all four gases with only a 1.3 second integration time and the cross interference was well below one percent for all gas combinations other than those between hydrocarbons. Sensitivity with other infrared sources was compared using ethylene as an example gas. In the comparison of sensitivity with different infrared sources the electrically modulated blackbody radiator gave a 35 times higher and the CO2-laser a 100 times lower detection limit than the blackbody radiator with a mechanical chopper. As a conclusion, the differential system is well suited to rapid single gas measurements. Gas-phase photoacoustic FTIR spectroscopy gives the best performance, when several components have to be analyzed simultaneously from multicomponent samples. Multicomponent measurements were demonstrated with a sample that contained different concentrations of CO₂, H₂O, CO, and four different hydrocarbons. It required an approximately 10 times longer measurement time to achieve the same detection limit for a single gas as with the differential system. The properties of the photoacoustic FTIR spectroscopy were also compared to conventional transmission FTIR spectroscopy by simulations. Solid- and liquid-phase photoacoustic FTIR spectroscopy has several advantages compared to other techniques and therefore it also has a great variety of applications. A comparison of the signal-to-noise ratio between photoacoustic cells with a cantilever microphone and a condenser microphone was done with standard carbon black, polyethene, and sunflower oil samples. The cell with the cantilever microphone proved to have a 5-10 times higher signal-to-noise ratio than the reference detector, depending on the sample. Cantilever enhanced photoacoustics will be an effective tool for gas detection and analysis of solid- and liquid-phase samples. The preliminary prototypes gave good results in all three measurement schemes that were studied. According to simulations, there are possibilities for further enhancement of the sensitivity, as well as other properties, of each system.

Operation and Maintenance Security Service for OSS-RC networks

Security issues in telecommunication networks have become more important due to the development of the industry. The number of network elements and services has increased in the radio network as in the core network side, which has increased the number of security related issues. Ericsson has developed an OSS-RC product for operation and maintenance porpoises into the telecommunication networks. OSS-RC is used in a number of telecommunications operators, which have Ericsson's products used in their telecommunication networks. Ericsson provides product installation and maintenance support and guidance, but despite this, the product may have security related issues, either due to lack of following the instructions, human error or defect in the product itself or in a third party products attached. Ericsson’s Operation and Maintenance Security Service for OSS-RC networks aims to provide tools for checking the security level of the O&M product so that it meets all requirements and Ericsson’s own security related rules. Each customer has a unique telecommunications network structure and services, and so the security service has to be to create individually depending on the customer. The purpose of this thesis is to define the basic instructions for creating the security service for different customers.

Future vision of information networks according to EU 7th framework

The purpose of this thesis is to investigate projects funded in European 7th framework Information and Communication Technology- work programme. The research has been limited to issue ”Pervasive and trusted network and service infrastructure” and the aim is to find out which are the most important topics into which research will concentrate in the future. The thesis will provide important information for the Department of Information Technology in Lappeenranta University of Technology. First in this thesis will be investigated what are the requirements for the projects which were funded in “Pervasive and trusted network and service infrastructure” – programme 2007. Second the projects funded according to “Pervasive and trusted network and service infrastructure”-programme will be listed in to tables and the most important keywords will be gathered. Finally according to the keyword appearances the vision of the most important future topics will be defined. According to keyword-analysis the wireless networks are in important role in the future and core networks will be implemented with fiber technology to ensure fast data transfer. Software development favors Service Oriented Architecture (SOA) and open source solutions. The interoperability and ensuring the privacy are in key role in the future. 3D in all forms and content delivery are important topics as well. When all the projects were compared, the most important issue was discovered to be SOA which leads the way to cloud computing.

Development of research networks : the case of social capital

The aim of this study is to explore how a new concept appears inscientific discussion and research, how it diffuses to other fields and out of the scientific communities, and how the networks are formed around the concept. Text and terminology take the interest of a reader in the digital environment. Texts create networks where the terminology used is dependent on the ideas, viewsand paradigms of the field. This study is based mainly on bibliographic data. Materials for bibliometric studies have been collected from different databases. The databases are also evaluated and their quality and coverage are discussed. The thesauri of those databases that have been selected for a more in depth study have also been evaluated. The material selected has been used to study how long and in which ways an innovative publication, which can be seen as a milestone in a specific field, influences the research. The concept that has been chosen as a topic for this research is Social Capital, because it has been a popular concept in different scientific fields as well as in everyday speech and the media. It seemed to be a `fashion concept´ that appeared in different situations at the Millennium. The growth and diffusion of social capital publications has been studied. The terms connected with social capital in different fields and different stages of the development have also been analyzed. The methods that have been used in this study are growth and diffusion analysis, content analysis, citation analysis, coword analysis and cocitation analysis. One method that can be used tounderstand and to interpret results of these bibliometric studies is to interview some key persons, who are known to have a gatekeeper position in the diffusion of the concept. Thematic interviews with some Finnish researchers and specialists that have influenced the diffusion of social capital into Finnish scientificand social discussions provide background information. iv The Milestone Publications on social capital have been chosen and studied. They give answers to the question "What is Social Capital?" By comparing citations to Milestone Publications with the growth of all social capital publications in a database, we can drawconclusions about the point at which social capital became generally approved `tacit knowledge´. The contribution of the present study lies foremost in understanding the development of network structures around a new concept that has diffused in scientific communities and also outside them. The network means both networks of researchers, networks of publications and networks of concepts that describe the research field. The emphasis has been on the digital environment and onthe socalled information society that we are now living in, but in this transitional stage, the printed publications are still important and widely used in social sciences and humanities. The network formation is affected by social relations and informal contacts that push new ideas. This study also gives new information about using different research methods, like bibliometric methods supported by interviews and content analyses. It is evident that interpretation of bibliometric maps presupposes qualitative information and understanding of the phenomena under study.

Modelling flexible asset management in industrial maintenance companies and networks

The tightening competition and increasing dynamism have created an emerging need for flexible asset management. This means that the changes of market demand should be responded to with adjustments in the amount of assets tied to the balance sheets of companies. On the other hand, industrial maintenance has recently experienced drastic changes, which have led to an increase in the number of maintenance networks (consisting of customer companies that buy maintenance services, as well as various supplier companies) and inter-organizational partnerships. However, the research on maintenance networks has not followed the changes in the industry. Instead, there is a growing need for new ways of collaboration between partnering companies to enhance the competitiveness of the whole maintenance network. In addition, it is more and more common for companies to pursue lean operations in their businesses. This thesis shows how flexible asset management can increase the profitability of maintenance companies and networks under dynamic operating conditions, and how the additional value can then be shared between the network partners. Firstly, I have conducted a systematic literature review to identify what kind of requirements for asset management models are set by the increasing dynamism. Then I have responded to these requirements by constructing an analytical model for flexible asset management, linking asset management to the profitability and financial state of a company. The thesis uses the model to show how flexible asset management can increase profitability in maintenance companies and networks, and how the created value can be shared in the networks to reach a win-win situation. The research indicates that the existing models for asset management are heterogeneous by nature due to the various definitions of ‘asset management’. I conclude that there is a need for practical asset management models which address assets comprehensively with an inter-organizational, strategic view. The comprehensive perspective, taking all kinds of asset types into account, is needed to integrate the research on asset management with the strategic management of companies and networks. I will show that maintenance companies can improve their profitability by increasing the flexibility of their assets. In maintenance networks, reorganizing the ownership of the assets among the different network partners can create additional value. Finally, I will introduce flexible asset management contracts for maintenance networks. These contracts address the value sharing related to reorganizing the ownership of assets according to the principles of win-win situations.

Communication Solutions for LVDC Island Networks

Production and generation of electrical power is evolving to more environmental friendly technologies and schemes. Pushed by the increasing cost of fossil fuels, the operational costs of producing electrical power with fossil fuels and the effect in the environment, like pollution and global warming, renewable energy sources gain con-stant impulse into the global energy economy. In consequence, the introduction of distributed energy sources has brought a new complexity to the electrical networks. In the new concept of smart grids and decen-tralized power generation; control, protection and measurement are also distributed and requiring, among other things, a new scheme of communication to operate with each other in balance and improve performance. In this research, an analysis of different communication technologies (power line communication, Ethernet over unshielded twisted pair (UTP), optic fiber, Wi-Fi, Wi-MAX, and Long Term Evolution) and their respective characteristics will be carried out. With the objective of pointing out strengths and weaknesses from different points of view (technical, economical, deployment, etc.) to establish a richer context on which a decision for communication approach can be done depending on the specific application scenario of a new smart grid deployment. As a result, a description of possible optimal deployment solutions for communication will be shown considering different options for technologies, and a mention of different important considerations to be taken into account will be made for some of the possible network implementation scenarios.