Characterization Of Process Efficiency Improvement In Laser Additive Manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, has gained a lot of interest in past recent years within various industries, such as medical and aerospace industries. LAM enables fabrication of complex 3D geometries by melting metal powder layer by layer with laser beam. Research in laser additive manufacturing has been focused in development of new materials and new applications in past 10 years. Since this technology is on cutting edge, efficiency of manufacturing process is in center role of research of this industry. Aim of this thesis is to characterize methods for process efficiency improvements in laser additive manufacturing. The aim is also to clarify the effect of process parameters to the stability of the process and in microstructure of manufactured pieces. Experimental tests of this thesis were made with various process parameters and their effect on build pieces has been studied, when additive manufacturing was performed with a modified research machine representing EOSINT M-series and with EOS EOSINT M280. Material used was stainless steel 17-4 PH. Also, some of the methods for process efficiency improvements were tested. Literature review of this thesis presents basics of laser additive manufacturing, methods for improve the process efficiency and laser beam – material- interaction. It was observed that there are only few public studies about process efficiency of laser additive manufacturing of stainless steel. According to literature, it is possible to improve process efficiency with higher power lasers and thicker layer thicknesses. The process efficiency improvement is possible if the effect of process parameter changes in manufactured pieces is known. According to experiments carried out in this thesis, it was concluded that process parameters have major role in single track formation in laser additive manufacturing. Rough estimation equations were created to describe the effect of input parameters to output parameters. The experimental results showed that the WDA (width-depth-area of cross-sections of single track) is correlating exponentially with energy density input. The energy density input is combination of the input parameters of laser power, laser beam spot diameter and scan speed. The use of skin-core technique enables improvement of process efficiency as the core of the part is manufactured with higher laser power and thicker layer thickness and the skin with lower laser power and thinner layer thickness in order to maintain high resolution. In this technique the interface between skin and core must have overlapping in order to achieve full dense parts. It was also noticed in this thesis that keyhole can be formed in LAM process. It was noticed that the threshold intensity value of 106 W/cm2 was exceeded during the tests. This means that in these tests the keyhole formation was possible.

Näkökulmia 3D-tulostuksen opetukseen ja koulutukseen

Additive manufacturing, or 3D printing, is globally one of most interesting area in developing of manufacturing technologies. This technology is suitable for fabrication off industrial products and it interests actors in fields of computer sciences, economics, medical sciences and design&arts. Additive manufacturing is often referred as third industrial revolution: first revolution was invention of steam engines in 18th century and second was industrial revolution started by Henry Ford in 1920s. Companies should be able to test suitability of their products for additive manufacturing and 3D printing but also how much better products could be when products are totally re-designed so that all potential of this new technology can be utilized. This is where education has its importance; new generations who enter working life should be educated to know of additive manufacturing and 3D printing, its advantages but also of it limits. There has to be also possibility to educate industry and people already working there, so that industrial implementation could be done successfully. This is especially very valid for Finland. Education is strongly needed so that Finnish industry can maintain its competence in global markets. Role of education is extremely important when a new technology is industrially implemented. Additive manufacturing and 3D printing offers freedom to design new products, production and generally ways of doing things. Development, planning and execution of education for additive manufacturing and 3D printing is challenging as this area develops very fast. New innovations are coming almost every month. Planning of education for additive manufacturing and 3D printing requires collection pieces of data from various of sources. Additive manufacturing and 3D printing industry and its development has to be followed frequently, and material for additive manufacturing and 3D printing has to be renewed frequently.

Näin opetan lisäävää valmistusta ja 3D-tulostusta: Pohdintoja uuden teknologian opetuksesta ja koulutuksesta

Additive manufacturing (shortened as AM), or more commonly 3D printing, consists of wide variety of different modern manufacturing technologies. AM is based on direct printing of a digital 3D model to a final product which is fabricated adding material layer by layer. This is from where term additive manufacturing has its origin. It is not only material what is added, but it is also value, properties etc. which are added. AM enables production of different and even better products compared to conventional manufacturing technologies. An estimation of potential of additive manufacturing can be gathered by considering the potential of laser cutting, which is one of the most widely used modern manufacturing technologies. This technique has been used over 40 years, and whole market around this technology is at the moment c. four billion euros and yearly growth is around 10 %. One factor affecting this success of laser cutting is that laser cutting enables radical improvements to products made of flat sheet. AM and 3D printing will do the same for three dimensional parts. Laser devices, which are at the moment used in 3D printing, are globally at the moment only around 1% of all laser devices used in any fabrication technology, so even with a cautious estimate the potential growth of at least 100 % is coming in next few years. Role of education is very important, when this kind of modern technology is industrially implemented. When both generation entering to work life and also generation who has been a while in work life understands new technology, its potential and limitations, this is the point when also product design can be rethought Potential of product design is driving force for wide use of additive manufacturing and 3D printing. Utilization of additive manufacturing and 3D printing is also opportunity for Finland and Finnish industry. This technology can save Finnish manufacturing industry. This technique has stron potential, as Finland has traditionally strong industrial know-how and good ICT knowledge.

Energy and raw material consumption analysis of powder bed fusion: case study: CNC machining and laser additive manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, is a powder bed fusion (PBF) type of additive manufacturing (AM) technology used to manufacture metal parts layer by layer by assist of laser beam. The development of the technology from building just prototype parts to functional parts is due to design flexibility. And also possibility to manufacture tailored and optimised components in terms of performance and strength to weight ratio of final parts. The study of energy and raw material consumption in LAM is essential as it might facilitate the adoption and usage of the technique in manufacturing industries. The objective this thesis was find the impact of LAM on environmental and economic aspects and to conduct life cycle inventory of CNC machining and LAM in terms of energy and raw material consumption at production phases. Literature overview in this thesis include sustainability issues in manufacturing industries with focus on environmental and economic aspects. Also life cycle assessment and its applicability in manufacturing industry were studied. UPLCI-CO2PE! Initiative was identified as mostly applied exiting methodology to conduct LCI analysis in discrete manufacturing process like LAM. Many of the reviewed literature had focused to PBF of polymeric material and only few had considered metallic materials. The studies that had included metallic materials had only measured input and output energy or materials of the process and compared to different AM systems without comparing to any competitive process. Neither did any include effect of process variation when building metallic parts with LAM. Experimental testing were carried out to make dissimilar samples with CNC machining and LAM in this thesis. Test samples were designed to include part complexity and weight reductions. PUMA 2500Y lathe machine was used in the CNC machining whereas a modified research machine representing EOSINT M-series was used for the LAM. The raw material used for making the test pieces were stainless steel 316L bar (CNC machined parts) and stainless steel 316L powder (LAM built parts). An analysis of power, time, and the energy consumed in each of the manufacturing processes on production phase showed that LAM utilises more energy than CNC machining. The high energy consumption was as result of duration of production. Energy consumption profiles in CNC machining showed fluctuations with high and low power ranges. LAM energy usage within specific mode (standby, heating, process, sawing) remained relatively constant through the production. CNC machining was limited in terms of manufacturing freedom as it was not possible to manufacture all the designed sample by machining. And the one which was possible was aided with large amount of material removed as waste. Planning phase in LAM was shorter than in CNC machining as the latter required many preparation steps. Specific energy consumption (SEC) were estimated in LAM based on the practical results and assumed platform utilisation. The estimated platform utilisation showed SEC could reduce when more parts were placed in one build than it was in with the empirical results in this thesis (six parts).

Characterization of design of a product for additive manufacturing

The purpose of conducting this thesis is to gather around information about additive manufacturing and to design a product to be additively manufactured. The specific manufacturing method dealt with in this thesis, is powder bed fusion of metals. Therefore when mentioning additive manufacturing in this thesis, it is referred to powder bed fusion of metals. The literature review focuses on the principle of powder bed fusion, the general process chain in additive manufacturing, design rules for additive manufacturing. Examples of success stories in additive manufacturing and reasons for selecting parts to be manufactured with additive manufacturing are also explained in literature review. This knowledge is demanded to understand the experimental part of the thesis. The experimental part of the thesis is divided into two parts. Part A concentrates on finding proper geometry for building self-supporting pipes and proper parameters for support structures of them. Part B of the experimental part concentrates on a case study of designing a product for additive manufacturing. As a result of experimental part A, the design process of self-supporting pipes, results of visual analysis and results of 3D scanning are presented. As a result of experimental part B the design process of the product is presented and compared to the original model.

Katsaus lisäävän valmistuksen (aka 3D-tulostus) mahdollisuuksiin ja kustannuksiin metallisten tuotteiden valmistuksessa: Case jauhepetitekniikka

Suurelle yleisölle lisäävä valmistustekniikka eli ns. 3D-tulostustekniikka näyttäytyy lehtien otsikoissa ja artikkeleissa esiin pulpahtavana ”muotiaiheena”, mutta sekä muovien 3D-tulostustekniikka että metallienkin vastaava valmistustekniikka on ollut olemassa maailmalla ja Suomessa 80-luvun puolivälistä alkaen. Yhdysvalloissa ja Saksassa tekniikkaa käytetään valmistavassa teollisuudessa toiminnallisten osien tuotannossa. Esimerkiksi lentokoneen suihkumoottorien osia ja lääketieteellisiä välineitä tehdään metallijauheesta lisäävän valmistuksen avulla. Itse asiassa eräs menetelmä metalliesineiden valmistamiseksi lasersäteen avulla keksittiin Suomessa ja sitä myös kehiteltiin täällä, mutta teollisuudenala lähti aikanaan nousuun Saksassa. Lisäävä valmistus on tällä hetkellä maailmanlaajuisesti eräs kiinnostavista tuotantotekniikoista, jonka uskotaan muuttavan monia asioita tuotteiden suunnittelussa, toiminnoissa ja valmistuksessa. Tämä tekniikka ei kiinnosta pelkästään valmistavaa teollisuutta, vaan tietotekniikan, lääketieteen, koruvalmistuksen ja muotoilun osaajat sekä uusien liiketoimintamallien kehittäjät ja logistiikka operaattorit ovat teknologiasta kiinnostuneita. Suomelle 3D-tulostustekniikka on suuri mahdollisuus, sillä maassamme on vahva teollinen tieto- ja viestintätekniikkaosaaminen sekä lisäksi olemme maassamme erikoistuneet varsin vaativien teollisiin laitteiden valmistukseen. Eräät suurimmista mahdollisuuksista tällä tekniikalla ovat toimitusketjuihin liittyvät muutokset. Uutta on, että pienetkin yritykset ja organisaatiot voivat soveltaa tätä tekniikkaa valmistuksessa ja jopa kehitellä täysin uusia tuotteita. On myös arvioitu, että lisäävän valmistuksen merkitys valmistustapoihin ja toimitusketjuihin voi olla suurempi kuin koskaan aikaisemmin minkään teknologisen uudistuksen kohdalla. Lisäävästä valmistuksesta usein puhutaankin kolmantena teollisena vallankumouksena juuri tämän takia. 3D-tulostuksen kustannuksia tarkasteltaessa on tärkeätä huomata että vain sulatetun jauheen määrä ratkaisee, ei käytettävän geometrian monimutkaisuus. Tämä erottaa perinteisen ja lisäävän valmistuksen toisistaan. Perinteisesti kappaleen keventäminen on maksanut ”ylimääräistä”, kun taas lisäävässä valmistuksessa kappaleen keveys on jopa kustannusta alentava tekijä. Valmistettavan kappaleen korkeus on yksi kriittisimpiä kustannuksiin vaikuttavia tekijöitä. Tämän vuoksi useamman kappaleen valmistus yhdellä kertaa parantaa kannattavuutta huomattavasti. Samalla kertaa voi ja itse asiassa kannattaakin valmistaa keskenään erilaisia kappaleita. Perinteiset valmistustavat sen sijaan ovat nykyajan vaatimuksille liian hitaita; ne joustavat huonosti, kun kyseessä on pienet, asiakaslähtöiset erät. Trendi on globaalisti kohden yksilöllisiä asiakaslähtöisiä tuotteita, jolloin myös valmistustekniikoiden on oltava joustavia pysyäkseen näiden vaatimusten perässä. Lisäävä valmistus sopii erityisesti hyvin piensarjatuotantoon. Suuremmissa valmistuserissä kuitenkin perinteiset tekniikat ovat kustannustehokkaampia.

Metal additive manufacturing of internal flow channels with powder bed fusion processes

This thesis studies the advantages, disadvantages and possibilities of additive manufacturing in making components with internal flow channels. These include hydraulic components, components with cooling channels and heat exchangers. Processes studied in this work are selective laser sintering and selective laser melting of metallic materials. The basic principles of processes and parameters involved in the process are presented and different possibilities of internal channel manufacturing and flow improvement are introduced

Monitoring Directed Energy Deposition Processes in Additive Manufacturing

The purpose of this study is to find out how laser based Directed Energy Deposition processes can benefit from different types of monitoring. DED is a type of additive manufacturing process, where parts are manufactured in layers by using metallic powder or metallic wire. DED processes can be used to manufacture parts that are not possible to manufacture with conventional manufacturing processes, when adding new geometries to existing parts or when wanting to minimize the scrap material that would result from machining the part. The aim of this study is to find out why laser based DED-processes are monitored, how they are monitored and what devices are used for monitoring. This study has been done in the form of a literature review. During the manufacturing process, the DED-process is highly sensitive to different disturbances such as fluctuations in laser absorption, powder feed rate, temperature, humidity or the reflectivity of the melt pool. These fluctuations can cause fluctuations in the size of the melt pool or its temperature. The variations in the size of the melt pool have an effect on the thickness of individual layers, which have a direct impact on the final surface quality and dimensional accuracy of the parts. By collecting data from these fluctuations and adjusting the laser power in real-time, the size of the melt pool and its temperature can be kept within a specified range that leads to significant improvements in the manufacturing quality. The main areas of monitoring can be divided into the monitoring of the powder feed rate, the temperature of the melt pool, the height of the melt pool and the geometry of the melt pool. Monitoring the powder feed rate is important when depositing different material compositions. Monitoring the temperature of the melt pool can give information about the microstructure and mechanical properties of the part. Monitoring the height and the geometry of the melt pool is an important factor in achieving the desired dimensional accuracy of the part. By combining multiple different monitoring devices, the amount of fluctuations that can be controlled will be increased. In addition, by combining additive manufacturing with machining, the benefits of both processes could be utilized.

3D-tulostustekniikan hyödyntäminen diagnostisten pikatestien tuotekehityksessä

Pikamallinnustekniikat ovat kehittyneet viime vuosina nopeasti. Tämä antaa jo lähes rajat-tomat mahdollisuudet tuottaa 3D-tulostamalla erilaisia tuotteita. 3D-tulostuksen hyödyntä-minen on yleistynyt erityisesti teollisuuden ja teknologian aloilla. Tässä työssä tutkittiin miten 3D-tulostamista voidaan hyödyntää diagnostisten pikatestien tuotekehityksessä. Immunologinen lateral flow-testi on vasta-aineisiin perustuva, nopea ja helppokäyttöinen mittausmenetelmä pienten ainemäärien havaitsemiseen. Tässä työssä kehitettiin lateral flow-testikotelo, jonka suunnitteluun ja rakenteen mallintamiseen käytettiin 3D-tulostustekniikkaa. Testikotelon toimivuus lateral flow- testissä varmistettiin kehittämällä testikoteloon sopiva pikatesti, jonka suorituskykyä analysoitiin sekä visuaalisesti että Actim 1ngeni-lukulaitteella. Työ aloitettiin tutkimalla eri pikavalmistustekniikoita, joista testikotelon tulostamiseen valittiin SLA-tekniikka sen tulostustarkkuuden ja tuotteen pinnan laadun perusteella. Testikotelon suunnittelu aloitettiin määrittämällä millaisia ominaisuuksia testikotelolta haluttiin. Näitä ominaisuuksia olivat lateral flow-testin suojaaminen sekä testissä kulkevan näytteen virtauksen varmistamien. Lateral flow- testin kehityksessä hyödynnettiin osin aiemmin kehitetystä pikatestistä saatuja tietoja. Lateral flow- kasettitestin valmistusprosessi koostui seitsemästä eri prosessivaiheesta jotka olivat: Vasta-aineen/kontrollireagenssin konjugointi, näytetyynyn käsittely, konjugointityynyn käsittely, konjugointityynylle annostelu, membraanille annostelu, tikkujen laminointi ja leikkaus sekä kasettitestin kokoonpano. Kehitetyn lateral flow- kasettitestin toimivuus varmistettiin tutkimalla testin reaktiokinetiikkaa ja analyyttistä herkkyyttä sekä visuaalisesti että lukulaitteen avulla. Tutkimustulosten perusteella 3D-tulostus on erittäin hyödyllinen menetelmä pikatestien tuotekehityksessä suunniteltaessa testikotelorakenteita, näytteen annosteluvälineitä ja näiden yhdistelmiä.

3D-tulostettu tuuliturbiinin vaihteen pienoismalli

Työn aiheena on vaihteen pienoismallin suunnittelu ja toteutus 3d-tulostusta hyväksi käyttäen. Pienoismalli tehdään Moventas Gears Oy:n suunnittelemasta tuuliturbiinin vaihteesta. Vaihteen pienentämisestä johtuen malliin on suunniteltava uudet laakeripesät ja hammaspyörät. 3D-tulostuksen ja pienoismallin pienen koon ansiosta vaihdetta voidaan yksinkertaistaa suuresti ja näin vähentää tulostettavien osien määrää. Lisäksi työssä selvitetään, mitä ongelmia 3D-tulostus tuo valmistukseen ja suunnitteluun. Työn kirjallisessa osassa selvennetään planeettavaihteen toimintaa yleisesti sekä esitellään Exceed Series 3+ vaihdetta. Lisäksi kerrotaan 3D-tulostuksesta, sen periaatteesta, erilaisista tulostusmenetelmistä, tulostinlaitteesta ja mahdollisista ongelmista tulostuksessa. Kokeellinen osa koostuu pienoismallin suunnittelusta ja valmistuksesta. Valmistuksessa olleiden virheiden takia muutama osa jouduttiin tulostamaan uudelleen. Muutamia osia jouduttiin myös hieman jälkikäsittelemään tulostuksen jälkeen, jotta malli saatiin kasattua. Ongelmakohdaksi muodostui tulostimen ohjelmisto ja tulostustiedostot. Tulostusprosessi sujui kuitenkin hyvin. Lopputuloksena saatiin toimiva pienoismalli. 3D-tulostus toimii hyvin monimutkaisten kappaleiden tulostuksessa. Tulostuksen hinta nousi kuitenkin varsin korkeaksi. Tulostuslaitteistosta riippuen tulostuksen voisi mahdollisesti suorittaa myös halvemmallakin.

Welding of additively manufactured stainless steel parts: Comparative study between sheet metal and selective laser melted parts

Additive manufacturing is a fast growing manufacturing technology capable of producing complex objects without the need for conventional manufacturing process planning. During the process the work piece is built by adding material one layer at a time according to a digital 3D CAD model. At first additive manufacturing was mainly used to make prototypes but the development of the technology has made it possible to also make final products. Welding is the most common joining method for metallic materials. As the maximum part size of additive manufacturing is often limited, it may sometimes be required to join two or more additively manufactured parts together. However there has been almost no research on the welding of additively manufactured parts so far, which means that there has been very little information available on the possible differences compared to the welding of sheet metal parts. The aim of this study was to compare the weld joint properties of additively manufactured parts to those of sheet metal parts. The welding process that was used was TIG welding and the test material was 316L austenitic stainless steel. Weld joint properties were studied by making tensile, bend and hardness tests and by studying the weld microstructures with a microscope. Results show that there are certain characteristics in the welds of additively manufactured parts. The building direction of the test pieces has some impact on the mechanical properties of the weld. Nevertheless all the welds exhibited higher yield strength than the sheet metal welds but at the same time elongation at break was lower. It was concluded that TIG welding is a feasible process for welding additively manufactured parts.

Sulautetun ohjausjärjestelmän kehittäminen 3D-tulostimelle

Kandidaatintyössä tutkittiin Adam Klodowskin tutkimuksessa käytetyn menetelmän soveltuvuutta 3D-tulostimen mekanismiin. Tutkimustyö liittyy RepRap-projektiin, jonka tavoitteena on valmistaa 3D-tulostin 3D-tulostetuista osista. Mekaniikasta oli luotu matemaattinen malli, jota tutkittiin simuloinnin avulla. Työssä toteutettiin täysin yksilöity sulautettu ohjausjärjestelmä kyseiselle mekanismille ja tutkittiin järjestelmän soveltuvuutta käytäntöön. Tavoitteena oli vähentää komponenttien lukumäärää ja pienentää laitteiston vaatimaa tilaa.